Development and validation of a solid-phase extraction and gas chromatography-tandem mass spectrometry method for the determination of isopropyl-9H-thioxanthen-9-one in carton packaged milk

A simple and efficient method for the determination of isopropyl-9H-thioxanten-9-one (ITX) in different fat content milk samples and baby milk samples stored in packaged cartons was developed and validated. Samples were extracted using solid-phase extraction (SPE) and analysed by gas chromatography-tandem mass spectrometry operated in selected reaction monitoring mode (SRM). Validation was carried out in terms of limit of detection (LOD), limit of quantitation (LOQ), linearity, precision and trueness. LOD and LOQ values in the low microg/L were achieved, whereas linearity was established within 0.5-500 microg/L range. Good precision was obtained both in terms of intra-day repeatability and inter-day precision on two concentration levels (RSD% lower than 2%). Good percentage recoveries were obtained (92.0-102.0%) even in the presence of high amount of fat. Finally, the developed method was successfully applied to analyse a number of commercial milk samples with different fat content and baby milk samples.     

Determination of tetracyclines in bovine kidney by liquid chromatography/tandem mass spectrometry with on-line extraction and clean-up

A novel, sensitive, high performance liquid chromatography/tandem mass spectrometric (i.e. mass spectrometry/mass spectrometry) method with on-line extraction and clean-up for the screening and confirmation of residues of tetracyclines in kidney has been developed. After liquid extraction of homogenised kidney with McIlvain buffer, an aliquot of the extract is directly injected on the LC/MS/MS system with further extraction and clean-up of the sample on-line. Detection of the analytes was achieved by positive electrospray ionization followed by multiple reaction monitoring. For each tetracycline the collisional decomposition of the protonated molecule to a unique, abundant fragment ion was monitored. The method has been validated for tetracycline, oxytetracycline, chlortetracycline and doxycycline. Calibration curves resulting from spiked blank kidney samples at the 100-1200 microgram/kg level showed good linear correlation. At the level of 600 microgram/kg both within- and between-day precision, as measured by relative standard deviation (RSD), were less than 7%. The limits of detection (LODs) for tetracycline, oxytetracycline, chlortetracycline and doxycyline were 18, 23, 24 and 21 microgram/kg, respectively. The limits of quantification (LOQs) for tetracycline, oxytetracycline, chlortetracycline and doxycyline were 36, 46, 47 and 42 microgram/kg, respectively. The recoveries ranged from 71 to 91%. The procedure provides a rapid, reliable and sensitive method for the determination of residues of tetracyclines in bovine kidney. The advantage of this method over existing methods is its decreased sample preparation and analysis time, which makes the method more suitable for routine analysis.     

Determination of eight sulfonamides in bovine kidney by liquid chromatography/tandem mass spectrometry with on-line extraction and sample clean-up

A sensitive, high performance liquid chromatography/tandem mass spectrometric (i.e. mass spectrometry/mass spectrometry; LC/MS/MS) method with on-line extraction and sample clean-up for the screening and confirmation of residues of sulfonamides in kidney is described. The sulfonamides are extracted from homogenized kidney with methanol. After centrifugation of the extract, an aliquot of the extract is directly injected on the LC/MS/MS system with further extraction and clean-up of the sample on-line. Detection of the analytes was achieved by positive electrospray ionization (ESI) followed by multiple reaction monitoring. For each sulfonamide the collisional decomposition of the protonated molecule to a common, abundant fragment ion was monitored. The method has been validated for sulfadimethoxine, sulfaquinoxaline, sulfamethazine, sulfamerazine, sulfathiazole, sulfamethoxazole, sulfadiazine and sulfapyridine. Calibration curves resulting from spiked blank kidney samples at the 10-200 microg/kg level showed good linear correlation. At the level of 50, 100 and 200 microg/kg both within- and between-day precision, as measured by relative standard deviation (RSD), were less than 16%. The limits of detection (LODs) ranged from 5 to 13.5 microg/kg. The recoveries ranged from 78 to 82%. The procedure provides a rapid, reliable and sensitive method for the determination of residues of sulfonamides in bovine kidney. The advantage of this method over existing methods is its decreased sample preparation and analysis time, which makes the method more suitable for routine analysis.     

Determination of several pesticides in water by solid-phase extraction, liquid chromatography and electrospray tandem mass spectrometry

The analysis of pesticides in water samples is a problem of primary concern for quality control laboratories due to the toxicity level of these compounds and their public health risk. In order to evaluate the impact of pesticides in the Lisbon drinking water supply system, following the requirements of the European Union Directive 98/83/EC, we developed and validated an analytical method based on the combination of solid-phase extraction with liquid chromatography and tandem mass spectrometry. In this work, several pesticides were studied: imidacloprid, dimethoate, cymoxanil, carbendazime, phosmet, carbofuran, isoproturon, diuron, methidathion, linuron, pyrimethanil, methiocarbe, tebuconazole and chlorpyrifos. Several parameters of the electrospray source were optimized in order to get the best formation conditions of the precursor ion for each pesticide, namely capillary and extractor voltage, cone voltage, cone gas flow rate and desolvation gas flow rate. After optimization of the collision cell energy of the triple quadrupole, two different precursor ion-product ion transitions were selected for each pesticide, one for quantification and one for qualification, and these ions were monitored under time-scheduled multiple reaction monitoring (MRM) conditions. The selection of specific fragment ions for each pesticide guarantees a high degree of selectivity as well as additional sensitivity to quantify trace levels of these pesticides in water samples. This method showed excellent linearity ranges for all pesticides, with correlation coefficients greater than 0.9989. Determination limits (between 0.0041 and 0.0480 microg/L), precision (RSD <9.18%), accuracy and recovery studies in several water samples using solid-phase extraction were also performed.     

Determination of tetracycline residues in soil by pressurized liquid extraction and liquid chromatography tandem mass spectrometry

An optimized extraction and cleanup method for the analysis of chlortetracycline (CTC), doxycycline (DC), oxytetracycline (OTC) and tetracycline (TC) in soil is presented. Soil extraction in a pressurized liquid extraction system, followed by extract clean up using solid-phase extraction (SPE) and tetracycline determination by liquid chromatography tandem mass spectrometry (LC-MS/MS) provided appropriate efficiency and reproducibility. Different dispersing agents and solvents for soil extraction and several SPE cartridges for cleanup were compared. The best extraction results were obtained using ethylenediamine tetraacetic acid-treated sand as dispersing agent, and water at 70 °C. The most effective cleanup was obtained using Strata-X^TM sorbent in combination with a strong anion exchange cartridge. Recoveries ranged from 71% to 96% and precision, as indicated by the relative standard deviations, was within the range of 8–15%. The limits of quantification (LOQs) by using LC-MS/MS, based on signal-to-noise ratio (S/N) of 10, ranged from 1 μg kg⁻¹ for TC to 5 μg kg⁻¹ for CTC. These results pointed out that this technique is appropriate to determine tetracyclines in soils. Analysis of 100 samples taken in the Valencian Community revealed that, in soil, up to 5 μg kg⁻¹ CTC, 15 μg kg⁻¹ OTC, 18 μg kg⁻¹ TC, and 12 μg kg⁻¹ DC could be detected. Detection of the analytes in several samples, which typify great part of the Spanish agricultural soils, should be outlined as most important result of this study. Electronic supplementary material  The online version of this article (doi: ) contains supplementary material, which is available to authorized users.     

基质分散固相萃取-高效液相色谱-串联质谱法检测红薯中的植物生长调节剂

建立了基质分散固相萃取-高效液相色谱-串联质谱测定红薯中氯吡脲、6-苄氨基嘌呤、增效胺以及多效唑含量的方法。样品经硅胶分散剂研磨分散、甲醇洗脱提取后,采用Thermo hypersil GOLD C18色谱柱(150 mm×2.1mm,5μm),以甲醇和0.1%(体积分数)甲酸-5 mmol/L甲酸铵为流动相进行梯度洗脱,在电喷雾离子源正离子或负离子模式下以选择反应监测(SRM)模式检测,外标法定量。氯吡脲、6-苄氨基嘌呤、增效胺和多效唑分别在10.8~216.0、10.8~216.0、12.5~250.0和10.2~204.0 ng/g范围内呈良好的线性关系,相关系数(r2)均大于0.96。以信噪比等于10确定4种植物生长调节剂的定量限,氯吡脲、6-苄氨基嘌呤、增效胺和多效唑的定量限分别为0.1、0.3、0.2和0.1 ng/g。4种植物生长调节剂在50、100及200 ng/g加标水平下的回收率为85.3%~116.0%,相对标准偏差为0.6%~22.7%。该方法操作简单、准确,适用于红薯中氯吡脲、6-苄氨基嘌呤、增效胺以及多效唑的定量检测分析。     

Determination of atorvastatin and its metabolite ortho-hydroxyatorvastatin in human plasma by on-line anion-exchange solid-phase extraction and liquid chromatography tandem mass spectrometry

A rapid, sensitive, and specific method was developed and validated using liquid chromatography-tandem mass spectrometry for the simultaneous quantitation of atorvastatin (ATV) and its major metabolite ortho-hydroxyatorvastatin (o-HATV) in human plasma. The sample preparation involved a liquid–liquid extraction without chlorinated solvents and an on-line solid-phase extraction exploring the possibilities that anion exchange offers. The analytical method presented intraday and day-to-day variation below 10%; intraday and day-to-day accuracy stood between 94% and 105%; the limit of quantification was 0.1 ng/mL for ATV and 0.5 ng/mL for o-HATV; and the recovery was above 75% for both molecules. This method was applied successfully to quantitate ATV and o-HATV concentrations in an unstudied renal transplant recipient cohort treated with an immunosuppressive regime of tacrolimus and mycophenolic acid and a cohort of hypercholesterolemic patients included in the study as a control group. It can be used to evaluate patient adherence, drug–drug interactions, and pharmacokinetic/pharmacodynamic relationships. The results in our study showed that ATV and o-HATV levels in the renal transplant group were significantly increased (p < 0.001), compared to the hypercholesterolemic group.     

Determination of Fusarium mycotoxins by liquid chromatography/tandem mass spectrometry coupled with immunoaffinity extraction

A method for the simultaneous quantitative determination of deoxynivalenol (DON), T‐2 toxin (T‐2), HT‐2 toxin (HT‐2) and zearalenone (ZEN) in wheat and biscuit by liquid chromatography/electrospray ionization tandem mass spectrometry (LC/ESI‐MS/MS) coupled with immunoaffinity extraction is described. A clean‐up was carried out using a DZT MS‐PREP® immunoaffinity column (IAC), and the effect of the sample dilution rate and sample loading was investigated. Furthermore, the effects of ion suppression of a multifunctional column (MFC) and the IAC in the clean‐up were compared. The results with the DZT MS‐PREP® IAC showed that it is possible to make the sample dilution rate low, and indicated a higher solvent‐tolerance than usual with an IAC. Sample loading was optimized at 0.25 g. Ion suppression was lowered by purification of the toxins using the DZT MS‐PREP® IAC. Recoveries of each mycotoxin from wheat and biscuit samples spiked at two levels ranged from 78 to 109%. The limits of detection in wheat and biscuit was in the range of 0.03–0.33 ng·g^?1. From these studies, it is suggested that use of an IAC is effective in the clean‐up of each mycotoxin, and, when combined with LC/ESI‐MS/MS, it is good for the determination of mycotoxins in foodstuffs due to its rapidity and high sensitivity. Copyright © 2010 John Wiley & Sons, Ltd.     

Determination of pharmaceuticals in soils and sediments by pressurized liquid extraction and liquid chromatography tandem mass spectrometry

The present work describes the development of a sensitive analytical method based on pressurized liquid extraction (PLE) and pre-concentration by solid-phase extraction (SPE), followed by liquid chromatography–electrospray tandem mass spectrometry (LC–ESI-MS/MS) for the determination of seventeen pharmaceuticals in soils and sediments. The method is based on sample homogenisation using Na₂–EDTA washed sand and extraction with water at 90 °C. Special emphasis was placed on the optimization of the extraction procedure to develop a green method that reduces, at a maximum, the use of organic solvents in order to eliminate matrix components during the clean-up. The proposed method was linear in a concentration range from 0.3 to 333 ng g⁻¹, with correlation coefficients higher than 0.993. Method detection (MDLs) and quantification (MQLs) limits ranged from 0.1 to 6.8 ng g⁻¹ and from 0.25 to 23 ng g⁻¹, respectively. Absolute recoveries were analyte dependent, varying between 50% and 105% at the MQL level, except for fenofibrate (40%) and diclofenac (34%). The intra-day and inter-day precision was given by RSD values from 0.7% to 7.9% and from 1.6% to 14.5%, respectively. Acetaminophen, carbamazepine, ciprofloxacin, clofibric acid, codeine, diazepam, fenofibrate, metropolol, ofloxacin and propanolol were detected at concentrations from MDL to 35.62 ng g⁻¹ in soils and sediments from marsh areas. Due to the low recoveries, results for fenofibrate and diclofenac can only be considered as semi-quantitative. The method was fully suitable for the other 15 pharmaceuticals.     

Determination of ochratoxin A in wine by liquid chromatography tandem mass spectrometry after combined anion-exchange/reversed-phase clean-up

Ochratoxin A (OTA) is a mycotoxin produced by Aspergillus ochraceus and Penicillium verrucosum. It has been found and analysed in several foods and feeds. Owing to its toxicity and occurrence in food and feed, the European Community has issued directives and some countries have their own regulations for OTA contents in food, feed and beverages. This work describes a method for the determination of OTA in mulled and red wine. It is based on combined anion exchange/reversed-phase clean-up and was analysed by liquid chromatography coupled with tandem mass spectrometry (multiple reaction monitoring). The method was validated with natural contaminated and spiked wine samples with OTA contents from 1.34 to 3.48 g kg^–1. Owing to its accuracy, good reproducibility and repeatability, this easy method is a good alternative to liquid chromatography–fluorescence detection methods.     

Determination of phenothiazines in human body fluids by solid-phase microextraction and liquid chromatography/tandem mass spectrometry

Eleven phenothiazine derivatives with heavy side-chains were found to be extractable from human whole blood and urine samples by solid-phase microextraction (SPME) with a polyacrylate-coated fiber. The fiber was then injected into the desorption chamber of an SPME-liquid chromatography (LC) interface for LC/tandem mass spectrometry (MS/MS) with positive ion electrospray (ES) ionization. All compounds formed base peaks due to [M + 1](+) ions by LC/ES-MS/MS. By use of LC/ES-MS/MS, the product ions produced from each [M + 1](+) ion showed base peaks due to side-chain liberation. Selected reaction monitoring (SRM) and selected ion monitoring (SIM) were compared for the detection of the 11 phenothiazine derivatives from human whole blood and urine. SRM showed much higher sensitivity than SIM for both types of sample. Therefore, a detailed procedure for the detection of drugs by SRM with SPME-LC/MS/MS was established and carefully validated. The extraction efficiencies of the 11 phenothiazine derivatives spiked into whole blood and urine were 0. 0002-0.12 and 2.6-39.8%, respectively. The regression equations for the 11 phenothiazine derivatives showed excellent linearity with detection limits of 0.2-200 ng ml(-1) for whole blood and 4-22 pg ml(-1) for urine. The intra- and inter-day precisions for whole blood and urine samples were not greater than 15.1%. The data obtained after oral administration of perazine or flupentixol to a male subject are presented.     

Characterization of photodegradation products of alachlor in water by on-line solid-phase extraction liquid chromatography combined with tandem mass spectrometry and orthogonal-acceleration time-of-flight mass spectrometry

On-line solid-phase extraction liquid chromatography in combination with mass spectrometry (MS), i.e. MS/MS and orthogonal-acceleration time-of-flight MS, was used for the characterization of photodegradation products of alachlor in river water. Various MS/MS scan functions were used, in particular the precursor-ion and the daughter-ion modes, to screen for degradation products with structures closely related to that of alachlor and to obtain information on characteristic fragments of the degradation products. Elemental compositions of compounds found and some of their fragments were calculated from the accurate mass information obtained with orthogonal-acceleration time-of-flight MS. Some ten degradation products could be characterized by combining various types of mass spectral information. Since quite a number of isomers were identified, structures of the degradation products were proposed by considering the most likely fragmentation patterns in MS/MS experiments. Degradation products of alachlor found in the current study were compared with those reported in the literature.     

Determination of 2,6-dichlorobenzamide and its degradation products in water samples using solid-phase extraction followed by liquid chromatography–tandem mass spectrometry

An analytical method was developed for the determination of 2,6-dichlorobenzamide (BAM) and five degradation products thereof including 2-chlorobenzamide (OBAM), 2,6-dichlorobenzoic acid (DCBA), 2-chlorobenzoic acid (OBA), benzoic acid (BA) and benzamide (BAD) in water samples. Solid-phase extraction was combined with liquid chromatography coupled to tandem mass spectrometry using electrospray ionisation. Groundwater spiked at a concentration of 1.0 μg/L gave recoveries on day 1 between 91 and 102% (relative standard deviation: 2.2–26.5%) for OBAM, BAM, DCBA, BA and OBA, while BAD showed a somewhat lower recovery of 60% (relative standard deviation: 25%). Corresponding figures on day 3 gave recoveries of 97–110% (relative standard deviation: 3–22%) for OBAM, BAM, DCBA, BA and OBA, while BAD had a recovery of 51% (relative standard deviation: 4%). The final SPE-LC–MS/MS method had a LOD_Method of 0.009, 0.007, 0.010, 0.021, 0.253 and 0.170 μg/L groundwater for BAD, OBAM, BAM, DCBA, BA and OBA and a LOQ_Method of 0.030, 0.023, 0.035, 0.071, 0.842 and 0.565 μg/L groundwater in the same order of appearance. Analysis of three different Danish groundwaters confirmed the occurrence of BAM at levels exceeding the threshold value of 0.1 μg/L, while no degradation products were found above LOD_Method.     

Determination of closantel and rafoxanide in animal tissues by online anionic mixed-mode solid-phase extraction followed by isotope dilution liquid chromatography tandem mass spectrometry

A rapid and high-throughput isotope dilution LC-MS/MS method with online sample pre-concentration and clean-up using anionic mixed-mode SPE was described for the determination of closantel and rafoxanide in edible bovine and ovine tissues. Tissue samples were extracted with acetonitrile and acetone mixture (60:40, v/v). Sample pre-concentration, clean-up and analysis were completed simultaneously with the online MAX SPE LC-MS/MS system. Closantel-(13) C(6) and rafoxanide-(13) C(6) were used as the internal standards to improve the precision of the method. The method was validated with edible ovine and bovine tissues (muscle, kidney and liver) fortified at three different levels. The accuracy and RSD were 86-106% and ≤14%, respectively. This high-throughput method was suitable for routine quantitative analysis of closantel and rafoxanide in food safety surveillance samples.     

Determination of cardiovascular drugs in sewage sludge by matrix solid-phase dispersion and ultra-performance liquid chromatography tandem mass spectrometry

Analytical and Bioanalytical Chemistry - The current study presents a single step sample preparation procedure for the simultaneous determination of five antihypertensive (propranolol, losartan,...     

液相色谱-串联质谱法检测贝类产品中的原多甲藻酸贝类毒素

建立了一种贝类组织中原多甲藻酸(azaspiracid, AZA)贝类毒素主要成分AZA1的高效液相色谱-串联质谱检测方法。本方法采用甲醇-水(80:20, v/v)溶液对贝类组织中AZA1进行提取,并用MAX阴离子交换固相萃取(SPE)柱富集净化,使用Atlantis dC18(150 mm×4.6 mm, 5.0 μm)色谱柱分离,以含有50 mmol/L甲酸和2 mmol/L甲酸铵的乙腈-水溶液(80:20, v/v)为流动相进行等度洗脱,质谱采用选择反应监测(SRM)模式。AZA1在5 min内获得完全分离,且在48.85～2 442 ng/L范围内线性良好,相关系数为0.998 1。该方法检出限(S/N=3)为11.00 pg/g,添加水平为36.64、73.27、146.54 pg/g时的平均回收率为75.8%～82.5%(n=6),相对标准偏差小于10%。利用该方法对采自大连、青岛、广州水产品市场上的112个贝类样品进行了分析,发现采自大连和广州的部分贝类样品中含有AZA1。结果表明,该方法具有简单、快速、灵敏度高等特点,能充分满足贝类中AZA1检测的要求。     

Determination of perfluorinated compounds in wastewater and river water samples by mixed hemimicelle-based solid-phase extraction before liquid chromatography-electrospray tandem mass spectrometry detection

A comparative study on the use of cetyltrimethylammonium bromide (CTAB)-coated silica and sodium dodecyl sulphate (SDS)-coated alumina mixed hemimicelles-based solid-phase extraction (SPE) for the pre-concentration of six perfluorinated compounds (PFCs) in environmental water samples was presented. The six analytes heptafluorobutyric acid (HFBA), perfluoroheptanic acid (PFHeA), perfluorooctanic acid (PFOA), perfluorooctanic sulfonic (PFOS), perfluorononanic acid (PFNA) and perfluorodecanic acid (PFDeA) were quantitatively retained on both sorbent materials. The cationic surfactant (CTAB adsorbed onto silica) was more appropriate for SPE of PFCs. The main factors affecting adsolubilization of PFCs including the amount of surfactant, pH of solution, sample loading volume and desorption were investigated and optimized. Concentration factor of 500 were achieved by SPE of 500 mL of several environmental water samples. The method detection limits obtained for HFBA, PFHeA, PFOA, PFOS, PFNA and PFDeA were 0.10, 0.28, 0.07, 0.20, 0.10 and 0.05 ng/L, respectively. The relative standard deviation of recoveries ranged from 2 to 8%, which indicated good method precision.     

Determination of alkylphenol and bisphenol A in beverages using liquid chromatography/electrospray ionization tandem mass spectrometry

A comprehensive analytical method based on liquid chromatography electrospray ionization tandem mass spectrometry (LC–ESI–MS/MS) with negative ionization mode has been developed for measuring of alkylphenols and bisphenol A in beverage samples. Concentration and clean up of samples were performed on 200 mg OASIS HLB solid extraction cartridges. The effects of mobile phases and additives on ionization were assessed. The recoveries for each compound ranged from 76.7 to 96.9% and reproducibilities were represented as having relative standard deviation (R.S.D.) below 10%. The limits of quantification (LOQ) of the method under multiple-reaction monitoring (MRM) acquisition mode were 0.04, 0.03 and 0.2 ng L⁻¹ for 2 L of mineral drinking water and 2.0, 1.8 and 8.0 ng L⁻¹ for 50 mL of soda beverages.     

Determination of alkylphenol and alkylphenolethoxylates in biota by liquid chromatography with detection by tandem mass spectrometry and fluorescence spectroscopy

A quantitative method for the simultaneous determination of octylphenol, nonylphenol and the corresponding ethoxylates (1 to 5) in biota is presented. Extraction methods were developed for egg and fish matrices based on accelerated solvent extraction followed by a solid-phase extraction cleanup, using octadecylsilica or aminopropyl cartridges. Identification and quantitation were accomplished by liquid chromatography-electrospray tandem mass spectrometry (LC-MS-MS) and compared to the traditional liquid chromatography with fluorescence spectroscopy detection. LC-MS-MS provides high sensitivity and specificity required for these complex matrices and an accurate quantitation with the use of 13C-labeled internal standards. Quantitation limits by LC-MS-MS ranged from 4 to 12 ng/g in eggs, and from 6 to 22 ng/g in fish samples. These methods were successfully applied to osprey eggs from the Chesapeake Bay and fish from the Great Lakes area. Total levels found in osprey egg samples were up to 18 ng/g wet mass and as high as 8.2 microg/g wet mass in the fish samples.