Catalytic determination of vanadium with the bromate/iodide/ascorbic acid landolt reaction and conductometric monitoring

Vanadium (0–1 mg l^?1) is determined in solutions by a catalytic procedure with conductometric detection. Reaction times of the bromate/iodide/ascorbic acid Landolt reaction are evaluated from conductance vs. time traces, obtained with an instrument with compensation facilities. Results are evaluated by means of calibration graphs, where the t(0)/t(c) ratios are plotted against the concentration of vanadium. Kinetics and mechanism of the reactions are discussed and values for the rate coefficients as well as entropies and enthalpies of activation are presented.     

Sensitive and selective determination of molybdenum by flow injection chemiluminescence method combined with controlled potential electrolysis technique

A sensitive and selective flow injection chemiluminescence (CL) method combined with controlled potential electrolysis technique was described for the determination of molybdenum. The method is based on the chemiluminescence reaction of luminol with unstable molybdenum(III) in alkaline solution. The molybdenum(III) was on-line reduced from molybdenum(VI) via controlled potential electrolysis technique using a homemade flow-through carbon electrolytic cell at the potential of −0.6 V (versus Ag/AgCl). The method allows the determination of molybdenum in the 5.0×10⁻¹⁰ to 5.0×10⁻⁷ g ml⁻¹ range with a limit of detection (3σ) of 5×10⁻¹¹ g ml⁻¹ molybdenum. The relative standard deviation is 2.6% for the 1.0×10⁻⁹ g ml⁻¹ molybdenum solution in 11 repeated measurements. This method was successfully applied to the determination of molybdenum in water samples.     

Flow-injection catalytic spectrophotometic determination of molybdenum(VI) in plants using bromate oxidative coupling of p-hydrazinobensenesulfonic acid with N-(1-naphthyl)ethylenediamine

A novel flow-injection spectrophotometry has been developed for the determination of molybdenum(VI) at nanograms per milliliter levels. The method is based on the catalytic effect of molybdenum(VI) on the bromate oxidative coupling of p-hydrazinobenzenesulfonic acid with N-(1-naphthyl)ethylenediamine to form an azo dye (λ_max = 530 nm). Chromotropic acid (4,5-dihydroxy-2,7-naphthalenedisulfonic acid) acted as an effective activator for the molybdenum(VI)-catalyzed reaction and increased the sensitivity of the method. The reaction was monitored by measuring the change in absorbance of the dye produced. The proposed method allowed the determination of molybdenum(VI) in the range 1.0-20 ng mL⁻¹ with sample throughput of 15 h⁻¹. The limit of detection was 0.5 ng mL⁻¹ and a relative standard deviation for 10 ng mL⁻¹ molybdenum(VI) (n = 10) was 2.5%. The interfering ions were eliminated by using the combination of a masking agent and on-line minicolumn packed with cation exchanger. The present method was successfully applied to the determination of molybdenum(VI) in plant foodstuffs.     

New insights into the reaction of t-butylhydroperoxide with dichloro- and dimethyl(dioxo)molybdenum(VI)

Lewis-base adducts of dichlorodioxomolybdenum(VI) and dimethyldioxomolybdenum(VI) react in an equilibrium reaction with excess t-butylhydroperoxide (TBHP) under the formation of a seven-coordinated molybdenum(VI) complexes displaying a η¹-alkylperoxo-ligand. HCl/CH₄ elimination or the protonation of the Lewis-base ligand is not observed, the TBHP hydrogen atom is instead transferred to one of the terminal oxo ligands under the formation of a molybdenum bound OH moiety. The peroxo species is assumed to be the active catalyst in olefin epoxidation.     

Molecular sensing of 3-chloro-1,2-propanediol by molecular imprinting

A covalent interaction-based molecularly imprinted polymer (MIP) material for 3-chloro-1,2-propanediol (3-MCPD), a post-testicular anti-fertility agent and possible carcinogen and mutagen in food products containing acid-hydrolyzed vegetable proteins, has been successfully fabricated using 4-vinylphenylboronic acid as the functional monomer. Rebinding assay revealed that the binding constant, K_B, for the receptor sites and non-specific sites are 1.93±0.1×10⁴ and 2.74±0.7×10² M⁻¹, respectively. The estimated number of receptor site, B_max, imprinted is 123.3±3 μmol/g of MIP. The MIP material is able to act as a potentiometric chemosensor for 3-MCPD via increase in Lewis acidity of the receptor sites upon reaction of the arylboronic acid with 3-MCPD to form the more acidic arylboronic acid esters. A simple pH glass electrode is sufficient to monitor the analyte-specific rebinding. In unbuffered aqueous media, linear potentiometric response from 0 to 350 ppm of 3-MCPD can be achieved. The MIP-based chemosensing in a soya sauce matrix has also been attempted. It is found that the dynamic range of the potentiometric chemosensing response of the MIP material is much reduced, probably due to the blocking or deactivation of receptor sites by interferents in soya sauces. Nevertheless, the present work demonstrated the feasibility of using MIP-based chemosensors as semi-quantitative analytical tools for screening purposes in quality control of food products.     

Etude cinetique de l'oligomerisation de l'ethylene amorcee par le complexe butyl-lithium tertiaire NNN′N′ tetramethylethylenediamine (tBuLi-TMEDA)

tButyl-lithium in the presence of TMEDA progressively adds ethylene molecules to produce a linear alkyl-lithium compound. This oligomerization has been studied at low pressures (0–1 atm) and temperature (0°). The rate of consumption of ethylene depends on the pressure, tBuLi concentration, and TMEDA concentration. By varying the molar ratio r, (TMEDA/|tBuLi|₀), from 0–1 to 4·3, the rate of consumption increased up to r = 1, where it becomes independent of r. A mechanism for the addition reaction is proposed.     

Das chlorsilylsubstituierte Silanimin Bu2SiNSiClBu2

In the thermolysis of the silaterazolines silatetrazoline ^tBu₂SiNSiCl^tBu₂ · ^tBu₃SiN₃ the silanimine ^tBu₂SiNSiCl^tBu₂ and the silyl azide ^tBu₃SiN₃ are formed quantitatively. The silanimine ^tBu₂SiNSiCl^tBu₂ has been trapped with Et₃NHF, Me₃NHCl, water, 1-butene, 2,3-dimethyl-1,3-butadiene, isobutene, methylvinyl ether, and ^tBu₂SiClN₃. The structure of the disiloxane (^tBu₂SiCl-NH-Si^tBu₂)₂O and of the bis(di-tert-butylchlorsilyl)-substituted silatetrazoline ^tBu₂SiNSiCl^tBu₂ · ^tBu₂SiClN₃ has been determined by X-ray structure analysis.     

Titanium ketimide complexes as α-olefin homo- and copolymerisation catalysts. X-ray diffraction structures of [TiCp(NCBu2)Cl2] (Cp=Ind, Cp*)

The synthesis of [TiInd(NC^tBu₂)Cl₂] and the applications of [TiCp^′(NC^tBu₂)Cl₂] (Cp^′=Ind, Cp*, Cp) as ethylene and propylene homopolymerisation catalysts, as well as its behaviour as catalysts of ethylene and 10-undecen-1-ol copolymerisation are described. The optimisation of the catalytic reactions showed that all compounds are very active homopolymerisation catalysts, particularly [TiInd(NC^tBu₂)Cl₂] that gives 123.37 × 10⁶ g/(molTi [E] h) and 50.77 × 10⁶ g/(molTi [P] h) of linear polyethylene and atatic polypropylene, respectively. The less active homopolymerisation catalyst, [TiCp(NC^tBu₂)Cl₂], is the most effective ethylene/10-undecen-1-ol copolymerisation catalyst, leading to the highest degree of polar monomer incorporation. The polymers obtained were characterised by NMR and DSC. The molecular structures of [TiCp^′(NC^tBu₂)Cl₂] (Cp^′=Ind, Cp*) were determined by X-ray diffraction studies.     

The structure and complexation equilibria of copper(II) with 4-(\bar 4-nitrophenyl)azo-2-phenyloxazolin-5-one

Summary A spectrophotometric method for determining trace amounts of Cu^II using 4-( -nitro-phenyl)azo-2-phenyloxazolin-5-one has been devised. With this reagent, Cu^II forms a stable chelate, in the 6–9.5 pH range which obeys Beer's law at 555 nm with a molar absorptivity of 4.50 × 10³ mol^–1 cm². Other copper-group metals do not interfere with this process. The stoichiometry and stability constant of the copper chelate has been determined using spectrophotometric, potentiometric and conductometric methods.     

Chemical Modified Carbon Paste Electrode for Potentiometric Determination of Mo(VI) and its Application in Food Analysis and Agriculture Fertilizers

Since to the best of our knowledge, there is no potentiometric sensors based on carbon paste electrodes were proposed for the potentiometric determination of molybdenum(VI) ion. In this study, 2,2′-(propane-1,3-diylbis(oxy))dibenzoic acid (PBODBA) was synthesized and used as modifier in the fabrication of carbon paste electrode (CPE) for the quantification of molybdenum(VI). The developed electrodes I and II showed hexavalent Nernstian response of 9.80±0.05 and 9.90±0.08 mV decade⁻¹ over the concentration ranges of 1.0×10⁻⁷–1.0×10⁻³ and 1.0×10⁻⁸–1.0×10⁻³ mol L⁻¹, respectively. The electrodes showed good selectivity for Mo(VI). The modified electrodes were applied for the determination of Mo(VI) concentration in masscuaje agricultural fertilizer and spiked juice extractions containing several metals.     

Nouvelle méthode de mesure électrotitrimétrique1,2

The new method that we propose permits direct measurments of the speed of evolulion dE/de of an electromotive force.The application of this technique to electrometric titratons allows us to detect directly and accurately a great number of potentiometric, conductometric,and even amperometric titrations.     

Simultaneous determination of tin, germanium and molybdenum by diode array detection-flow injection analysis with partial least squares calibration model

Simultaneous determination of tin, germanium and molybdenum in food samples has been established by flow injection-charge coupled detector (CCD) diode array detection spectrophotometry with partial least squares (PLS) algorithm. The method was based on the chromogenic reaction of metal ions and salicylflurone in the presence of cetyltrimethyl ammonium bromide. The overlapping spectra of these complexes are collected by CCD diode array detector and the multi-wavelength absorbance data are processed using partial least squares algorithm. The reaction conditions and analytical parameters of flow injection analysis have been investigated. The method was applied to directly determine Ge, Mo and Sn in several food samples after digestion with satisfactory results. The recoveries of spiked samples were 80.0-102.0% for tin, 86.3-92.0% for germanium and 83.2-95.2% for molybdenum, and the relative standard deviations for samples were 4.4-7.8%. Molybdenum in certified reference material of cattle liver was determined by the proposed method (n=8). The differential values between determined and guarantee values were within the given uncertain value ranges (t=1.687, P>0.05 for t-test). The samples of mung bean, kelp and pork liver were analyzed by the proposed method and inductively couple plasma-atomic emission spectroscopy (ICP-AES) method. The determination results of the two methods are in good agreement. The sampling rate is 30 samples h⁻¹.     

Development of in situ ion selective sensors for dissolution

The dissolution of formulations of the drugs dapoxetine, paliperidone, cinnarizine, tetrazepam, mebeverine, loperamide, galantamine and ibuprofen was studied by an in-line potentiometric measurement system. The transpose of a Nikolskii-Eisenman type function performed the conversion of potential to percentage of dissolution. A novel gradient membrane electrode was developed especially for dissolution, varying continuously in composition from an ionically conducting rubber phase to an electronically conducting solid state PVC/graphite composite. The gradient part had a thickness of 200 μm. The electrodes life span exceeded 6 months. An ion exchange procedure was used to prepare them for one specific drug. This enabled us to use one universal electrode built to measure a wide array of drugs. The system parameters such as accuracy, reproducibility and linearity were presented with the data obtained for the drug dapoxetine. In dissolution, accurate measurements were possible from 10⁻⁹ to 10⁻³ M concentrations, for high log P drugs. The effect of t₉₀ response times on the measurement error was estimated. The t₉₀ response times of the electrodes were concentration dependent, and varied between 50 and 10 s for, respectively, 10⁻⁶ and 10⁻³ M concentrations. Potential drift was studied in detail. The measurements performed with these electrodes showed an accuracy of 1%, and inter- and intra electrode variabilities of 0.6 and 1.7%, respectively. The electrodes were successfully applied in colloidal media containing suspended matter, typically formed during dissolution of tablets. The advantages and pitfalls of potentiometry over the presently used techniques for dissolution testing are discussed.     

Monomer reactivity ratios of N-isopropylacrylamide-itaconic acid copolymers at low and high conversions

Copolymers of N-isopropylacrylamide (NIPAAm) and itaconic acid (IA) having various compositions were synthesized using free radical solution polymerization in 1,4-dioxane at 50 °C with α,α′-azobisisobutyronitrile (AIBN) as initiator. The structures of the copolymers were confirmed by Fourier transform infrared (FTIR) spectroscopic technique. The copolymer compositions were determined by conductometric and potentiometric methods from the inflection points in the acid-base titration curves and by FTIR spectroscopy through recorded analytical absorption bands for NIPAAm (1620 cm⁻¹ for CO stretching of secondary amides) and for IA (1704 cm⁻¹ for CO stretching) units, respectively. Monomer reactivity ratios of IA (F₁)-NIPAAm (F₂) pair were estimated using the Finemann-Ross, the inverted Finemann-Ross, the Kelen-Tüdós and the extended Kelen-Tüdós graphical methods. The values ranged from 0.40 to 0.60 for r₁ and from 1.20 to 1.90 for r₂, depending on the conversion percentage, calculation methods of monomer reactivity ratios and determination methods of copolymer compositions. In all cases, r₁r₂ < 1 and r₁ < r₂ indicate the random distribution of the monomers in the final copolymers and the presence of higher amount of NIPAAm units in the copolymer than that in the feed, respectively.     

The trace determination of some heavy metals in waters by flow-injection spectrophotometry and potentiometry

Three automated flow-injection systems are proposed for the determination of traces of manganese(II), lead and copper(II) in waters. The first system utilizes the catalytic effect of manganese(II) on the oxidation of N,N-diethylaniline by potassium periodate at pH 6.86–7.10 (30°C) and is used for spectrophotometric determination at 475 nm in the range 0.02–1.00 μg1^?1; the system involves reagent injection and stopped flow. The determination of lead in the range 0.7–100 μg1^?1 is based on spectrophotometric detection of the lead 4/(2-pyridylazo)resorcinol complex at 525 nm after on-line preconcentration of the sample (5–50 ml) on a minicolumn filled with Chelex-100 or Dowex 1-X8 resin. A potentiometric flow-injection system with a copper ion-selective electrode is applied for the determination of 0.5–1000 μg 1^?1 copper(II) after on-line preconcentration of 50–500 ml of sample on Chelex-100 resin. The procedures are tested on synthetic and real water samples, including sea water and waste-waters.     

Nickel-catalyzed C–O/N–H,C–S/N–H,and C–CN/N–H annulation of aromatic amides with alkynes: C–O,C–S,and C–CN activation

The Ni-catalyzed reaction of ortho-phenoxy-substituted aromatic amides with alkynes in the presence of LiO^tBu as a base results in C–O/N–H annulation with the formation of 1(2H)-isoquinolinones. The use of a base is essential for the reaction to proceed. The reaction proceeds, even in the absence of a ligand, and under mild reaction conditions (40 °C). An electron-donating group on the aromatic ring facilitates the reaction. The reaction was also applicable to carbamate (C–O bond activation), methylthio (C–S bond activation), and cyano (C–CN bond activation) groups as leaving groups.

The Ni-catalyzed reaction of ortho-phenoxy-substituted aromatic amides with alkynes in the presence of LiO^tBu as a base results in C–O/N–H annulation with the formation of 1(2H)-isoquinolinones.     

Kinetic isotope effects of nitrogen and hydrogen in reaction of N-tert-butyl-P-phenylphosphonamidothioic acid with alcohols

Nitrogen and hydrogen isotope effects for the reaction of N-tert-butyl-P-phenylphosphonamidothioic acid 1 with alcohols (methanol, butanol, iso-propanol, tert-butanol) were measured in dichloromethane at 30 °C. The observed nitrogen isotope effect k₁₄/k₁₅ is only slightly sensitive to a steric hindrance of the alcohol [1.0070 ± 0.0002 (MeOH), 1.0074 ± 0.0004 (BuOH), 1.0062 ± 0.0004 (PrⁱOH), 1.0087 ± 0.0007 (Bu^tOH)]. The pre-equilibrium step, with proton transfer from oxygen to nitrogen was proved by the inverse hydrogen effect k_ROH/k_ROD[0.778 ± 0.052 (MeOH), 0.863 ± 0.063 (BuOH), 0.883 ± 0.080 (PrⁱOH), 0.746 ± 0.084 (Bu^tOH)]. The experimental values are consistent with theoretical results of semiempirical calculations on PM3 level for an elimination-addition mechanism and metathiophosphonate PhPSO intermediacy. For the reaction with methanol the addition-elimination mechanism is also possible.     

Enantioselective, potentiometric membrane electrodes based on cyclodextrins: application for the determination of R-baclofen in its pharmaceutical formulation

Two enantioselective, potentiometric membrane electrodes based on α- and γ-cyclodextrins were proposed for the assay of R-baclofen. The slopes of the electrodes were 59.50 and 51.00 mV/pR-baclofen for α- and γ-cyclodextrin-based electrodes, respectively. The detection limits of the proposed electrodes were 7 × 10⁻⁹ mol l⁻¹ for α-cyclodextrin-based electrode and 1.44 × 10⁻¹⁰ mol l⁻¹ for γ-cyclodextrin-based electrode. The enantioselectivity was determined over S-baclofen. The proposed electrodes can be employed for the assay of R-baclofen raw materials and its pharmaceutical formulation, Norton-Baclofen^® tablets. The surfaces of the electrodes are stable and easily renewable by polishing on alumina paper.     

A novel method of the separation/preconcentration and determination of trace molybdenum(VI) in water samples using microcrystalline triphenylmethane loaded with salicyl fluorone

It is the first time that triphenylmethane was used as an adsorbent to preconcentrate and separate trace amount of molybdenum in water samples. The effects of different parameters, such as acidity, stirring time and various metal ions, the amounts of triphenylmethane and salicyl fluorine, etc. on the enrichment yield of molybdenum have been studied to optimize the experimental conditions. Under the optimum conditions, molybdenum can be adsorbed on the surface of microcrystalline triphenylmethane loaded with salicyl fluorone by the intermolecular action strength. The possible reaction mechanism for the enrichment of molybdenum was discussed in detail in this paper. Mo(VI) can be completely separated from Pb(II), Co(II), Cu(II), Cr(III), Ni(II), Hg(II), Zn(II), Cd(II), Fe(III) and Al(III) in the solution. The proposed method was successfully applied to the determination of trace amount of molybdenum in various water samples by spectrophotometry after preconcentration using microcrystalline triphenylmethane. The preconcentration factor is from 83 (500 ml water sample was enriched to 6.0 ml) to 166 (1000 ml water sample was enriched to 6.0 ml). The detection limit is 1.3 × 10⁻⁵ mg l⁻¹ and the linearity is maintained in the concentration range 3.8 × 10⁻³ to 0.36 mg l⁻¹ with a correlation coefficient of 0.9998. The recoveries are in the range of 93.5-104%. The relative standard deviation is 1.8-2.9%. Analytical results obtained with this novel method are very satisfactory.