Study of chemical modifiers for direct determination of silver in sea water by ETA-AAS with deuterium background correction

Methods for the direct determination of silver in sea water samples by ETA-AAS using different chemical modifiers were studied. The effect of salinity was studied using synthetic sea water of high (72.8 per thousand) and low (34.2 per thousand) salinity, and the results were compared with aqueous standard solutions. The charring temperatures achieved were 800 and 900 degrees C for magnesium nitrate and ammonium dihydrogen phosphate respectively, being 1100 degrees C for palladium nitrate and their mixtures. The best sensitivity obtained in the peak-height measurement mode was achieved by using reduced palladium (limit of detection (LOD) between 0.5 and 1.1 mug l(-1) for an injection volume of 20 mu1) with analytical recoveries close to 100% for synthetic and real sea water samples. The use of ammonium dihydrogen phosphate (LOD of 1.3 mug l(-1) for an injection volume of 20 mu1) produced good recoveries for low salinity; at high salinity an increase of around 25% was obtained, the method being unsuitable for sea water analysis. Finally, an interference study of the major components of sea water was carried out and applied to the analysis of surface sea water from the Galicia coast.     

Microwave induced plasma atomic emission spectrometry: a suitable detection system for the determination of volatile halocarbons

Microwave induced plasma atomic emission spectrometry (MIP-AES), a highly sensitive detection system for organometal compounds, was coupled to an automated purge and trap gas chromatographic system for the determination of volatile halogenated hydrocarbons in environmental water samples. Optimisation of the parameters affecting the injection and detection system led to relative detection limits from 1 to 14 ng · L^–1 for chlorine- and bromine-compounds and from 10 to 75 ng · L^–1 for iodine-compounds, on basis of a 10 mL sample volume. A comparison of the analytical characteristics between atomic emission detection (AED) and electron capture detection (ECD) showed a lower sensitivity of the atomic emission detector for halocarbons, but the detection thresholds are low enough to use the method for the determination of volatile halocarbons in trace level concentrations. The ability of the atomic emission detector provides increased selectivity for monitoring individual halogenated compounds under simplified and rapid chromatographic conditions, within a total analysis time of only 30 min. The method was applied with gas chromatographic separation for the analysis of sea water samples. Concentrations for the different elements between 0.05 and 15.28 μg · L^–1 were determined.     

A new analytical methodology for a fast evaluation of semi-volatile polycyclic aromatic hydrocarbons in the vapor phase downstream of a diesel engine particulate filter

A new sampling method was developed to collect vapor-phase polycyclic aromatic compounds (PAHs) downstream of a diesel engine equipped with a diesel particulate filter (DPF). This configuration allowed us to collect separately the particulate phase, which was trapped inside the DPF, and the vapor phase, which was sampled downstream of the DPF. PAHs, which were not predominantly absorbed into the poor organic fraction of the diesel soot, but were rather physically sorbed on high energetic adsorption sites, should be extracted using very drastic extraction conditions Microwave-assisted extraction using solvent mixtures composed of pyridine and diethylamine were used to desorb particulate PAHs, and the total PAH amounts corresponded to a very low value, i.e., 8 μg g⁻¹ or 0.24 μg km⁻¹, with a predominance of low weight PAHs. For collection of the vapor phase, gas bubbling in an aqueous medium was preferred to conventional methods, e.g., trapping on solid sorbents, for several reasons: aqueous trapping allowed us to use a solid phase enrichment process (SPE) that permitted PAH sampling at the sub-picogram levels. Consequently, low volume sampling was possible even if the sampling duration was very short (20 min). Additionally, the amount of time saved for the analysis was considerable when coupling SPE to the analytical system (liquid chromatography with fluorimetric detection). Solvent consumption for the overall sampling and analytical processes was also drastically reduced. Experiments on a diesel engine showed that vapor phase samples collected downstream of the DPF contained all of the 15 target priority PAHs, even the heaviest ones. The total vapor-phase PAH amount was 6.88 μg N m⁻³ or 10.02 μg km⁻¹, which showed that the gaseous fraction contains more PAHs than the particulate fraction. Partitioning coefficients (K_p) were estimated showing the predominance in the vapor phase of all the PAHs. However, the DPF technology effects a considerable decrease in the total PAH emission when compared to non-equipped diesel vehicles.     

Continuous water purification system for Langmuir film studies

A system for continuous purification of water to make it suitable for use in Langmuir film studies has been designed and implemented in our laboratory. The system incorporates particulate filtration, activated carbon adsorption, deionization by reverse osmosis, and continuous distillation under a nitrogen sweep. Surface tension in excess of 99% of theoretical and resistivity of 18 Megohm-cm at 25°C have been achieved without the use of organic ion exchange resins.     

Direct Determination of Total Chromium in Sea Water by Graphite Furnace Atomic Absorption Spectrometry with Multiple Injections

The method of multiple injections coupled with graphite furnace and atomic absorption spectrometry is applied to direct determination of total chromium at extremely small concentrations in samples of open sea water. The method involves the in situ preconcentration of trace chromium in sea water onto a pyrocoated graphite tube by multiple injections (up to 4 × 90 μL) prior to analysis. The selected ashing temperature is up to 1800 °C, and the background signal caused by high sea-salt contents will be markedly reduced when the ashing time is prolonged up to 200 s. A CASS-2 reference sea water has been used as a quality control sample in the analyses of samples of open sea water samples; the results were found to agree with the certified value. Due to the use of a relatively large volume (up to 0.36 mL) of sample for direct determination of trace chromium in sea water, the detection limit for chromium is 0.057 ppb.     

High-resolution mass spectrometry method for the detection, characterization and quantitation of pharmaceuticals in water

The presence of pharmaceuticals in drinking water is an emerging environmental concern. In most environmental testing laboratories, LC-MS/MS assays based on selected reaction monitoring are used as part of a battery of tests used to assure water quality. Although LC-MS/MS continues to be the best tool for detecting pharmaceuticals in water, the combined use of hybrid high-resolution mass spectrometry (HRMS) and ultrahigh pressure liquid chromatography (UHPLC) is starting to become a practical tool to study emerging environmental contaminants. The hybrid LTQ-orbitrap mass spectrometer is suitable for integrated quantitative and qualitative bioanalysis because of the following reasons: (1) the ability to collect full-scan HRMS spectra with scan speeds suitable for UHPLC separations, (2) routine measurement of mass with less than 5 ppm mass accuracy, (3) high mass resolving power, and (4) ability to perform on-the-fly polarity switching in the linear ion trap (LTQ). In the present work, we provide data demonstrating the application of UHPLC-LTQ-orbitrap for the detection, characterization and quantification of pharmaceuticals and their metabolites in drinking water.     

Semi-automated disk-type solid-phase extraction method for polychlorinated dibenzo-p-dioxins and dibenzofurans in aqueous samples and its application to natural water

A disk-type solid-phase extraction (SPE) method was used for the extraction of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in natural water and tap water. Since this SPE system comprised airtight glass covers with a decompression pump, it enabled continuous extraction with semi-automation. The disk-type SPE method was validated by comparing its recovery rates of spiked internal standards with those of the liquid-liquid extraction (LLE). The recovery ranges of both methods were similar in terms of (13)C-labeled internal standards: 64.3-99.2% for the LLE and 52.4-93.6% for the SPE. For the native spike of 1,3,6,8-tetrachlorinated dibenzo-p-dioxin (TCDD) and octachlorinated dibenzo-p-dioxin (OCDD), the recoveries in the SPE were in the normal range of 77.9-101.1%. However, in the LLE, the recoveries of 1,3,6,8-TCDD decreased significantly. One of the reasons for the low recovery is that the solubility of this congener is high. The semi-automated SPE method was applied to the analysis of different types of water: river water, snow, sea water, raw water for drinking purposes, and tap water. PCDD/F congeners were found in some sea water and snow samples, while their concentrations in the other samples were below the limits of detection (LODs). This SPE system is appropriate for the routine analysis of water samples below 50L.     

Anodic stripping voltammetry in a flow-through cell with a fixed mercury film glassy carbon disc electrode. Part I

Anodic stripping voltammetry at a glassy carbon disc electrode covered by a thin mercury film was adapted for use in a flow-through cell. The resulting system is characterized by extreme simplicity of set-up and operation, high sensitivity and excellent precision and stability. Its performance was tested via the determination of hydrated or labile complex ions of heavy metal ions in sea water, using short (2–10 min) deposition periods. The dependence of the stripping peak charge on metal ion concentration, length of deposition period, solution flow rate and other variables was examined and the reliability of the results obtained were evaluated under conditions resembling continuous monitoring.     

Direct electrothermal atomic absorption spectrometry determination of nickel in sea water using multiple hot injection and Zeeman correction

Methods for the direct determination of Ni in sea water samples by ETAAS were developed using Zeeman effect background correction system (ZEBC) and a multi-injection technique. A mass of palladium nitrate of 2.5 mug (for an injection volume of 100 mul) was used as chemical modifier. The optimum pyrolysis and atomization temperatures were 1700 and 2100 degrees C, respectively. The characteristic mass (m(0)) and characteristic concentration (C(0)), precision and accuracy were studied for different injection volumes (20, 100 and 200 mul). For an injection volume of 100 mul (five 20 mul aliquot) of sample the accuracy analysis of different certified materials (saline and non saline water) was agreeable. The total time of the proposed procedure is 6 min. A m(0) and C(0) of 34.5 pg and 0.3 mug l(-1), respectively were obtained for this injection volume (100 mul). Finally, interferences from major and minor components of sea water was studied.     

Polyhydroxamic Acid Sorbents for Uranium Recovery

Crosslinked polyacrylamides were synthesized by solution polymerization using benzoyl peroxide as the radical initiator. The water–insoluble polymer obtained was functionalized by reacting with hydroxylamine to convert the amide group into hydroxamic acid group. The resultant functionalized polymer was characterized in terms of moisture uptake, elemental composition, IR spectra, thermal stability, exchange capacity and heavy metal sorption. The sorbent, obtained in particulate form, was investigated for its sorption properties with respect to uranium from uranyl nitrate solutions under unstirred batch conditions. This paper will concentrate on preparation, characterization and performance evaluation with respect to uranium sorption as a function of concentration, time, solution pH and temperature. The potential of this sorbent for uranium and other heavy metal ion recovery from sea water is ascertained.     

EB-radiolysis of carbamazepine: in pure-water with different ions and in surface water

A method for the rapid and simultaneous monitoring of particulate and dissolved ¹³⁷Cs concentration in water was developed. This method uses pleated polypropylene nonwoven fabric filter to collect particulate radiocesium, and nonwoven fabric impregnated with Prussian blue (PB) to absorb dissolved radiocesium. The fabric was placed into cylindrical plastic cartridges (SS-cartridge and PB-cartridge). Traditional monitoring methods, such as evaporative concentration, often require time for pre-processing. However, this method described requires much less pre-processing time before the detection. Experiments conducted with simulated river water demonstrated that almost all of the suspended solids weight was collected in the SS-cartridge, and that more than 92 % of dissolved ¹³⁷Cs was absorbed onto the two PB-cartridges by 2.5 L/min flow rate when the range of the pH was 6–8. This device was applied to monitor Abukuma River water at two locations and the results were compared with those obtained using the filtrating and evaporative concentration method. The suspended solids concentration in river water, calculated by weight gain of the SS-cartridge and by sediment weight after filtration with a 0.45-μm membrane filter, agreed well. The radioactivity of the particulate and dissolved ¹³⁷Cs also agreed well in one of the two replications of this method. In addition, the required time for pre-processing was reduced by 60 times that by filtrating and evaporative concentration method. This method can separately collect and concentrate particulate and dissolved radiocesium rapidly and simultaneously in the field.     

Study on air pollution monitoring in Korea using low volume air sampler by instrumental neutron activation analysis

The aim of this research was to enhance the use of nuclear analytical techniques for air pollution studies and to study the feasibility of the use of instrumental neutron activation analysis (INAA) as a routine monitoring tool to reveal environmental pollution sources. For the collection of air particulate samples, the Gent stacked filter unit, low volume sampler with Nucleopore membrane filters were used. Trace elements in samples collected at two suburban residential sites, Taejon and Wonju city in the Republic of Korea, were analyzed by INAA. Variations of the elemental concentrations were measured monthly and the enrichment factors were calculated for the fine (<2 μm EAD) and coarse size (2–10 μm EAD) fractions. The analytical data were treated statistically to estimate the relationship between the two variables, the concentrations of elements and the total suspended particulate matter. The results were used to describe the emission source and their correlation.     

The determination of dissolved chromium(III) and chromium(VI) and particulate chromium in waters at μg l-1 levels by thin-film x-ray fluorescence spectrometry

A method is described for the determination of particulate chromium and dissolved chromium(III) and (VI) in water at μg l^-1 levels. Particulate material is collected by filtration of the water sample through a membrane filter (0.4-μm pore-size). Chromium(III) and chromium(VI) are then coprecipitated, separately and in that order, with iron(III) hydroxide (at pH 8.5) and a cobalt—pyrrolidinedithiocarbamate carrier complex (at pH 4.0). Both precipitates are collected as thin films on membrane filters and, with the particulate material, analysed directly for chromium by x-ray fluorescence spectrometry. Detection limits, for a 100-ml water sample and counting times of 100 s, are 0.1 μg Cr l^-1. The method is unaffected by sea salt and is applicable, without modifications, to river and estuarine waters.     

A sensitive colorimetric method for the micro determination of iodine in marine water

More than 70% of the earth surface is covered by water bodies. Marine pollution is associated with the discharge of oils, petroleum products, sewage agricultural wastes, pesticides, heavy metals, waste substances and dumping of radioactive waters in sea. This in turn results in hazards to human health, hindrance to aquatic organisms and impairment of quality for use of sea water. Sea water is reported to contain iodine but the concentration varies according to the location and depth. Here a simple and sensitive method is described for the determination of iodine using leucocrystal violet as a reagent in different samples of sea water. The method is based on the oxidation of iodine to iodate with bromine water and the liberation of free iodine from the iodate by addition of potassium iodide in acedic medium. This iodine selectively oxidises leucocrystal violet to form the crystal violet dye. Beer's law is obeyed over the concentration range of 0.04-0.36 ppm of iodine at lambda(max) 592 nm. The dye was further extracted in chloroform. The extracting system obeys Beer's law in the range of 0.008-0.08 ppm at lambda(max) 588 nm.     

Determination of 1-nitropyrene in low volume ambient air samples by high-performance liquid chromatography with fluorescence detection

To measure the actual exposure of a person to 1-nitropyrene (1-NP) in airborne particulate matter, it is considered more accurate to collect air samples with a portable air sampler than to sample at a fixed location. However, because the portable samplers can sample only small volumes, a sensitive method is needed to analyze the compounds that are collected on a filter. Here we describe a high-performance liquid chromatographic (HPLC) method with fluorescence detection that is sensitive and precise enough for use with portable air samplers. The developed column-switching system successfully removed the interfering substances in the samples with only a simple pretreatment. To improve the precision of the measurement, deuterated 1-NP was used as an internal standard, and it eluted immediately prior to 1-NP with sufficient resolution (R_s, 1.50). The detection limit was 0.32 fmol/injection, and the calibration range was from 2 to 100 fmol. The proposed method was applied to determining 1-NP in fine airborne particulate matter (PM_2.5) at two sites with low pollution levels. 1-NP was detected in all samples at concentrations in the low fmol/m³ range. The proposed method has enough sensitivity and precision to determine 1-NP in the limited air volume of the portable sampler.     

Chemiluminescence method with potassium permanganate for the determination of organic pollutants in seawater.

A chemiluminescence method with potassium permanganate was developed for use as an indicator of organic pollutants in fresh water. This method could be applied to the determination of organic pollutants in seawater as well. However, the flow chemiluminescence method suffered from the interference of chloride ions at the same concentration of seawater because of the production of manganese dioxide in the oxidation of chloride ions with permanganate. The conditions (concentrations of potassium permanganate and sulfuric acid and sample volume, i.e. flow injection method) were chosen to minimize the interference of chloride ions. The chemiluminescence method shows a good correlation with the chemical oxygen demand method on fresh water added artificial sea salt and seawater samples. Natural seawater was analyzed by the chemiluminescence method. The results obtained were compared with those obtained by chemical oxygen demand under the alkaline condition and total organic carbon methods. The chemiluminescence method has higher sensitivity and reproducibility than the conventional chemical oxygen demand and total organic carbon methods.     

Chemical speciation of chromium in sea water : Part 2. Effects of Manganese Oxides and Reducible Organic Materials on the Redox Processes of Chromium

Experiments designed to clarify the role of manganese oxides in the oxidation process of Cr(III) to Cr(VI) in sea water are described. The theoretical redox equilibrium controlled only by dissolved oxygen is shown not to be always attained for the Cr(III)/ Cr(VI) system in practice. Some naturally occurring materials can reduce Cr(VI) under the conditions of natural sea water.     

Comparative study of magnesium nitrate,palladium nitrate and reduced palladium for the direct determination of mercury in sea water by electrothermal atomization atomic absorption spectrometry

A comparative study of different chemical modifiers in graphite furnace atomic absorption spectrometry for the direct determination of mercury in sea water samples, in synthetic sea water sample of high (72.8%) and low 34.2%) salinity and in aqueous solutions, was carried out. The use of reduced palladium produces better results. The mixture of palladium nitrate and ascorbic acid, gives the best limit of detection (1.9 gl^–1). The use of reduced palladium and magnesium nitrate produced excellent recoveries (close to 100%) in the whole salinity range for all mercury concentration tested. The use of palladium nitrate alone or combined with magnesium nitrate gave good recoveries with respect to a real sea water sample for low salinities. The interference from the major components of sea water were completely removed by using reduced palladium and magnesium nitrate modifiers. Thus, a single calibration curve with synthetic sea water may be applied to the analysis of sea water samples of widely differing salinities.     

The determination of chromium species in natural waters

A method for the determination of chromium species has been developed and successfully applied to both fresh and sea water samples. The method utilizes pre-concentration of total chromium, chromium(ni) and particulate chromium at natural pH with accurate and precise analysis by a single flameless atomic absorption procedure. A minimal blank allows for a reliable detection limit of 0.02 nM, which is sufficient for most natural waters with chromium concentrations in the range 0.01–10 nM. Immediate shipboard preconcentration of the samples minimizes storage problems. The method is simple and rapid; 20 samples can be analysed in duplicate for total chromium, chromium(III) and particulate chromium in one day with routinely available reagents and equipment.     

Improved analysis of Polycyclic Aromatic Hydrocarbons in atmospheric particulate matter by HPLC-fluorescence

An improved method is reported for determination of Polycyclic Aromatic Hydrocarbons (PAHs) in atmospheric particulate matter by HPLC-FLD. The sampling step (air volume collected during each sampling period varies in the range 10/13 m3) is carried out by means of a medium-flow pumping system (15 L min(-1)) on a glass fiber filter (47 mm diameter) placed as collecting substrate in the sampling-cassette. After sampling, the filter is extracted with 3 ml of acetonitrile in an ultrasonic bath for 30 minutes. As for extraction of PAHs from loaded filters a new criterion here is proposed to evaluate the recovery efficiency of PAHs from the sample, instead of the usual spiking method of standard solution. The extract was then reduced to 100 microL and analysed by HPLC-FLD on line spectra system. The method is rapid (about one hour for extraction and analysis), reproducible and enables to measure with good accuracy the atmospheric concentration of benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(a)pyrene (BaP), benzo(ghi)perylene (BghiP), carcinogenic compounds always present in the urban airborne particulate matter. So it is useful for routine pollution studies and suitable to substitute the official method used now. Monthly average air concentrations, for the four PAHs above mentioned, measured in Rome from July 2001 to June 2002, are reported.