Concentration of polyaromatic hydrocarbons in water to sodium dodecyl sulfate-gamma-alumina admicelle

Polyaromatic hydrocarbons (PAHs) in water were concentrated into sodium dodecyl sulfate (SDS)-gamma-alumina and di-2-ethylhexyl sodium sulfosuccinate (Aerosol-OT, AOT)-gamma-alumina admicelles. The comparison of the binding constants (Kad[={adsorbed concentration of the solute (mol/g surfactant)}/{the concentration in the bulk aqueous phase (mol/ml)}] indicated almost the same extraction abilities of the both admicelles. However, better and more reproducible recovery was obtained in the concentration of PAHs into the SDS-gamma-alumina admicelle. PAHs in tobacco smoke that were trapped in water were successfully concentrated into SDS-gamma-alumina admicelle for the HPLC analysis.     

超声萃取-高效液相色谱法测定沉积物中多环芳烃

提出了高效液相色谱法测定沉积物中多环芳烃(PAH′s)含量的方法。样品中多环芳烃用正己烷-丙酮(1+1)混合溶液超声提取,离心分离后,所得萃取液经蒸发浓缩,然后过装有1g无水硫酸钠和2g硅胶的层析柱净化。以Varian PAHs色谱柱为分离柱,不同比例配成的甲醇和水为流动相梯度洗脱,用荧光检测器检测。方法的检出限(3S/N)在0.34～1.52ng.g-1之间。方法用于沉积物中多环芳烃的测定,测定结果的相对标准偏差(n=5)在3.2%～10.6%之间。用标准加入法测定方法的回收率,结果在57.1%～103.4%之间     

DNA Nanogels To Snare Carcinogens: A Bioinspired Generic Approach with High Efficiency

Polycyclic aromatic hydrocarbons (PAHs) are combustion‐related pollutants and are ubiquitous in the environment, including in sources of drinking water. Upon contact with DNA, stable PAH–DNA adducts form rapidly as the first step towards their toxic effects. In this work, we prepared hydrophilic DNA nanogels to exploit this generic complexation process as a biomimetic scavenging method. This approach relies on interaction between PAHs and the complete network that constitutes the water‐swollen nanogels, and is not restricted to interfacial adsorption. Up to 720 μg of PAH per gram of DNA nanogel are taken up, meaning that 1 mg of DNA nanogel is sufficient to purify a liter of water containing the critical PAH concentration for cancer risk (600 ng L^?1). As a result of short diffusion pathways, PAH uptake is rapid, reaching 50 % loading after 15 minutes. Beyond PAHs, DNA nanogels may be useful for the generic detoxification of water containing genotoxins, since most known molecules that strongly associate with DNA are mutagenic.     

Determination of polycyclic aromatic hydrocarbons in the needles of a Scotch pine (<Emphasis Type="Italic">Pinus sylvestris</Emphasis> L.), a biomonitor of atmospheric pollution

A procedure was developed for the determination of polycyclic aromatic hydrocarbons (PAH) in the needles of a Scotch pine (Pinus sylvestris L.), which is characterized by the simple and efficient sample preparation. The procedure involves the steps of the extraction of PAH with n-hexane on ultrasonic irradiation, the precipitation of concomitant cereous components from the extract on its cooling, the purification of the PAH fraction on a cartridge with silica gel (0.5 g), and the redissolution of the concentrated eluate in methanol. The quantitative determination of PAH (15 compounds including 13 priority) with the use of chromatography-mass spectrometry in the selective ion detection mode exhibits the interlaboratory precision of the results of the PAH determination V _Rl = 0.059–0.088 for the concentration of PAH in needles from 0.3 to 600 ng/g and a detection limit of 0.06 ng/g (signal-to-noise ratio = 3; mass of the sample for extraction was 10 g). The accumulation levels of PAH in the Scotch pine needles were presented; the needles were first studied as a biomonitor of atmospheric pollution over the southern part of the Baikal natural territory.     

Decomposition‐Assembly of Tetraphenylethylene Nanoparticles With Uniform Size and Aggregation‐Induced Emission property

Tetraphenylethylene (TPE)‐substituted poly(allylamine hydrochloride) (PAH‐g‐TPE) is synthesized by a Schiff base reaction between PAH and TPE‐CHO. The PAH‐g‐TPE forms micelles in water at pH 6, which are further transformed into pure TPE‐CHO nanoparticles (NPs) with a diameter of ≈300 nm after incubation in a solution of low pH value. In contrast, only amorphous precipitates are obtained when TPE‐CHO methanol solution is incubated in water. The aggregation‐induced emission feature of the TPE molecule is completely retained in the TPE NPs, which can be internalized into cells and show blue fluorescence. Formation mechanism of the TPE NPs is proposed by taking into account the guidance effect of linear and charged PAH molecules, and the propeller‐stacking manner between the TPE‐CHO molecules.     

Preparation of transparent conductive multilayered films using active pentafluorophenyl ester modified multiwalled carbon nanotubes

A mutilayered film was prepared by layer-by-layer (LBL) assembly of active ester modified multiwalled carbon nanotubes (MWCNTs) and poly(allylamine hydrochloride) (PAH). For this purpose, carboxylic groups on the surface of the oxidized MWCNTs were converted to the acyl chlorides by their reaction with thionyl chloride. Subsequent reaction of the acyl chlorides with pentafluorophenol formed the active esters. These active ester modified MWCNTs (MWCNTs-COOC 6F 5) were air-stable and moisture resistant, but showed a high reactivity toward primary or secondary amines resulting in amide bonds. For the preparation of a multilayered film, the surface of a quartz slide was first activated and sacrificial double layers of PAH and poly(sodium 4-styrene sulfonate) (PSS) were deposited. Subsequently, LBL assembly of MWCNTs-COOC 6F 5 and PAH was then conducted on these double layers [(PAH/PSS) 2]. In the process of the assembly, a reaction occurred between the active ester on the surface of MWCNTs and the amine groups of polyallylamine yielding amide bonds, which resulted in a mechanically stable thin film. A free-standing film was obtained after dissolving the sacrificial layer [(PAH/PSS) 2] in a concentrated aqueous NaOH solution. The surface resistance of the multilayered film with 20 bilayers decreased to around 10 kOmega while remaining a reasonable transparency (70% at 500 nm).     

Counterions and water in polyelectrolyte multilayers: a tale of two polycations

Attenuated total internal reflectance Fourier transform infrared, ATR-FTIR, spectroscopy was used to compare the water uptake and doping within polyelectrolyte multilayers made from poly(styrene sulfonate), PSS, and a polycation, either poly(allylamine hydrochloride), PAH, or poly(diallyldimethylammonium chloride), PDADMAC. Unlike PDADMA/PSS multilayers, whose water content depended on the solution ionic strength, PAH/PSS multilayers were resistant to doping by NaCl to a concentration of 1.2 M. Using (infrared active) perchlorate salt, the fraction of residual counterions in PDADMA/PSS and PAH/PSS was determined to be 3% and 6%, respectively. The free energy of association between the polymer segments, in the presence of NaClO4, was about 5 kJ mol-1 and -10 kJ mol-1, respectively, for PDADMA/PSS and PAH/PSS, indicating the relatively strong association between the polymer segments in the latter relative to the former. Varying the pH of the solution in contact with the PAH/PSS multilayer revealed a transition to a highly swollen state, interpreted to signal protonation of PAH under much more basic conditions than the pKa of the solution polymer. The increase in the multilayer pKa suggested an interaction energy for PAH/PSS in NaCl of ca. 16 kJ mol-1.     

Partitioning of polycyclic aromatic hydrocarbons in the polyethylene/water system

The suitability of polyethylene sheets as passive samplers of lipophilic contaminants in water bodies was tested. High-density polyethylene (HDPE) and low-density polyethylene (LDPE) sheets were contaminated with PAH. Uncontaminated and pre-contaminated sheets were deployed simultaneously and collected at intervals over 32 days. The exposed sheets and water samples were analyzed for PAH. The initial PAH concentrations in the contaminated and uncontaminated sheets differed by two to three orders of magnitude, but approached a common equilibrium concentration during exposure. The two- to four-ring PAH achieved quasi-equilibrium within the 32-day exposure period, whereas the five- and six-ring PAH did not. The estimated PE/water partition coefficients were approximately three times higher for HDPE than for LDPE, and they were similar in magnitude to the K(ow) values (the partition coefficients between n-octanol and water). The uptake rate constants were approximately four times higher for HDPE than LDPE, which was attributed to the four times higher specific surface area. The uptake and elimination in HDPE followed linear first-order kinetics, whereas for LDPE very slow elimination rates were observed that could not be explained. The results show that PE is a simple, effective, and inexpensive material for sampling trace organic contaminants in water.     

Polycyclic aromatic hydrocarbon analysis in different matrices of the marine environment

Polycyclic aromatic hydrocarbons (PAHs) were determined in marine samples of various types, i.e. seawater, sediment and mussel homogenate samples. The samples were spiked with standard PAH mixtures in both polar (acetonitrile) and non-polar (i-octane) solvents, then extracted. Extraction from seawater was performed by liquid/liquid extraction to hexane (LLE) and with solid phase extraction (SPE) discs. The water samples were filtered and unfiltered seawater, and redistilled water for comparison. The discs with PAHs adsorbed from water samples, and also the sediment and mussel homogenate samples, were extracted with acetonitrile by sonication. PAHs in the disc extracts and from the LLE were cleaned-up using TLC and next determined by GC/MS/IT (with ion-trap) and HPLC-DAD/UV. The analytical procedures were verified with deuterated PAH standard mixtures. The large differences in PAH recoveries (from 12 to 86% for sum, and from 3 to 135% for particular PAHs) do not depend solely on the type of matrix and analytical procedure applied (e.g. standard solvent, volume of evaporated sample), but also on the concentration and molecular structure of the analyte. Usually, only a fraction of each PAH content in the matrix is determined, depending on the particulate matter in seawater and the sorption properties of the solid matrix. The recoveries of deuterated PAHs are higher than those of non-deuterated compounds.     

Determining PAHs and PCBs in aqueous samples: finding and evaluating sources of error

This work describes the problems that occur during routine multi-step determinations of polyaromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs), which can be present at trace levels in water, and identifies sources of analyte losses at particular steps during the analytical procedure. PAH and PCB adsorption onto the walls of the container ranged from 0 to 70%. PAH and PCB recoveries of >70% were achieved during the LLE and SPE extraction steps. During the process of enriching the dichloromethane extract with PAHs and PCBs, based on the gentle evaporation of solvent, losses were <24% and <19%, respectively. Model experiments show that neither isolation of PAHs and PCBs (performed using either LLE or SPE) nor extract enrichment reduce the reliability of PAH and PCB determination. The steps that lead to the greatest loss of analyte are the ones that involve sampling, transport and storage of the water samples.     

Polymer film sensor for sampling and remote analysis of polycyclic aromatic hydrocarbons in clear and turbid aqueous environments

A sensor for remote analysis of polycyclic aromatic hydrocarbons (PAHs) has been developed. It is based on direct solid phase extraction of the pollutants on a polymeric film, followed by monitoring the laser induced fluorescence, emitted from the film, via optical fibers. The proposed sensor has been applied to direct PAH analysis in clear and turbid aqueous environments. Linear calibration plots have been obtained for PAH solutions containing both humic substances and clay suspensions. Detection limits in the range of 10 ppt have been achieved. Results are obtained almost instantaneously (in drinking water) or within minutes, in more complicated matrices. This set-up has provided considerable improvement of the detection limits, when compared to the traditional fiber-optic fluorescence probe. In case of pyrene, a 100-fold and a 250-fold improvement in the detection limits have been obtained for the clay and humic substances-containing water, respectively. The spectral response of the polymeric film has been studied under various conditions and the feasibility of the method for analysis of PAH mixtures has been addressed.     

Probing of polyelectrolyte monolayers by zeta potential and wettability measurements

Detection of the very first step of polyelectrolyte adsorption onto a solid support is of great importance for understanding mechanisms of solid surface modification. It was shown that streaming potential and contact angle measurements can be successfully used for polyelectrolyte (PE) adsorption characterization in a broad range of surface coverage. Cationic polyallylamine hydrochloride (PAH) was used for the formation of the layer. The electrokinetic characteristics of the substrate covered by the PAH layer were compared with contact angles measured under wet (captive air bubble/substrate in water) and dry (sessile water droplet/dried substrate) conditions. It has been demonstrated that contact angle values determined under both conditions are in good agreement. The observed rapid increase in the contact angle from zero for the bare mica surface to the value close to one characteristic of the PAH monolayer appears in the same PAH coverage range as zeta potential value changes due to adsorption. These results show that wettability can be as sensitive to the presence of small amounts of adsorbed species as electrokinetic measurements.     

Determination of polycyclic aromatic hydrocarbons in water by gas chromatography/mass spectrometry with accelerated sample preparation

A novel simplified sample preparation method for quantitative analysis of polycyclic aromatic hydrocarbons (PAH) in water samples by gas chromatography/mass spectrometry (GC/MS) was proposed. The method requires just 1 mL of water and 1 mL of dichloromethane. The detection limits of PAH with the use of high resolution GC/MS are about 1 μg/Λ, while the limits of quantification—10 μg/L. These limits correspond to those for the standard 8270 method of the United States Environmental Protection Agency.     

Salt softening of polyelectrolyte multilayer microcapsules

By using a combination of atomic force and confocal microscopy, we explore the effect of 1:1 electrolyte (NaCl) on the stiffness of polyelectrolyte microcapsules. We study the "hollow" and "filled" (with polystyrene sulfonate) capsules. In both cases the shells are composed of layers of alternating polystyrene sulfonate (PSS) and polyallylamine hydrochloride (PAH). The stiffness of both "hollow" and "filled" capsules was found to be largest in water. It decreases with salt concentration up to approximately 3 mol/L and gets quasi-constant in more concentrated solutions. The "filled" capsules are always stiffer than "hollow." The observed softening correlates with the salt-induced changes in morphology of the multilayer shells detected with the scanning electron microscopy. It is likely that at concentrations below approximately 3 mol/L the multilayer shell is in a "tethered" state, so that the increase in salt concentration leads to a decrease in number of ionic cross-links and, as a result, in the stiffness. In contrast, above the critical concentration of approximately 3 mol/L multilayer shells might be in a new, "melted," state. Here the multilayer structure is still retained, but sufficient amount of ionic cross-links is broken, so that further increase in salt concentration does not change the capsule mechanics. These ideas are consistent with a moderate swelling of multilayers at concentrations below approximately 3 mol/L and significant decrease in their thickness in more concentrated solutions measured with surface plasmon spectroscopy.     

Mass distribution for the microextraction of polycyclic aromatic hydrocarbon metabolites investigated with fluorescence spectrometry

Mass-balance data were acquired using fluorescence spectrometry for 2-naphthol and three polycyclic aromatic hydrocarbon (PAH) metabolites using liquid-liquid-liquid microextraction and liquid-liquid microextraction systems. The PAH metabolites are very important biomarkers, and there has been no previously reported mass-balance data on these compounds with microextraction systems. In addition, the effects of two solvent systems used in the preparation of donor and acceptor phases were investigated. The effects of the solvent systems on the partitioning process were compared. The mass balance results showed that significant amounts of the hydrophobic metabolites were held in the pores of the microfiber in both the three-phase and two-phase microextraction systems. Based on the mass-balance data, a new enrichment factor was defined as the concentration of the solute trapped in the pores of the fiber divided by the initial concentration of the solute in the donor phase. Because of the relatively large amount of the solute in the pores, it is envisioned that the solutes could be easily extracted from the pores, the extraction solvent concentrated, and further separated by capillary electrophoresis or characterized by solid-matrix phosphorescence, solution fluorescence, or mass spectrometry.     

Initial applications of phospholipid-coated mercury electrodes to the determination of polynuclear aromatic hydrocarbons and other organic micropollutants in aqueous systems

Mercury electrodes coated with di-oleoyl lecithin are described for the determination of polynuclear aromatic hydrocarbons (PAHs) and other micropollutants in aqueous solutions. The coated electrodes give a characteristic response in the capacitance/voltage curve to three-, four- and five- ring PAHs. The extent of the negative potential shift in the reversible capacitance peaks (and thus sensitivity) is related to the number of aromatic rings and substituents on the PAH. The capacitance/voltage curves were recorded by phase-sensitive a.c. voltammetry. The response is quantitatively related to the concentration of PAH in solution. Detection limits are about 0.4 μg l^?1 and the reproducibility (RSD) for separate samples is 7%. Intercalibration of the method with fluorescence spectrophotometry of pyrene-spiked sea-water samples, showed recoveries of 80%. The analytical system is useful for sea water and tap water. Bovine serum albumin (1 mg l^?1) enhances the sensitivity to pyrene. The monolayer is sensitive to oil-contaminated waters ( > 40 μg l^?1). The capacitance peaks respond selectively to other groups of compounds and to individual compounds within a group. The monolayer appears highly sensitive to the solution behaviour of PAHs because only soluble unbound PAHs penetrate the monolayer. Humic acid added to the solution decreases the response to PAH presumably by binding a fraction of PAH in the solution.     

New on-line concentrator for LC-GC: Analysis of PAHs with LC-GC

A new, versatile, and low cost on-line LC-GC interface has been devloped for the fast and reliable introduction of large volume samples into a cappillary GC column without using the conventional retention gap. PAHs in soot were analyzed by on-line normal phase HPLC-capillary GC. A glass, vial-shaped on-line concentrator provides a zone for solvent evaporation and sample concentration. Large volumes of HPLC eluate can be concentrated with the on-line concentrator and then transferred directly into the cappillary column. Trace levels (< 10 ppb) of PAH compounds can be efficiently concentrated with the on-line concentrator and determined without loss or contamination.     

Fractionation of cigarette smoke condensate for chemical and biological testing

Large-scale fractionation of cigarette smoke condensate (CSC) was carried out by gel filtration and silicic acid column chromatography, and selected fractions and their subfractions were tested for tumorigenicity by mouse-skin bioassay. The weak-acid fraction was separated into four subfractions, the polynuclear aromatic hydrocarbon (PAH) fraction into two subfractions, and the polar neutral lipid fraction into three subfractions. Also, combinations of subfractions were examined for synergic effects and portions of all active material were subjected to chemical analyses by gel filtration, column, thinlayer and gas chromatography, and ultraviolet and mass spectrometry. A weak-acid subfraction (F-63) in which catechol was concentrated, and which comprized 3.27% CSC was shown to be tumorigenic, as were combinations of this sub fraction with the active PAH (F-67) sub fraction and a polar, neutral lipid (F-70) sub fraction, representing 0.01 and 0.05% CSC, respectively. The results indicated that catechol may be a potent cocarcinogen and that the PAH in CSC interact with other components to exert a tumorigenic effect.     

Penetration of mercury-adsorbed phospholipid monolayers by polynuclear aromatic hydrocarbons

The penetration of phospholipid monolayers (dioleoyl lecithin) adsorbed on mercury by polynuclear aromatic hydrocarbons (PAH) is described. The PAH studied were anthracene, phenanthrene, pyrene, benzo[a]anthracene, fluoranthene and perylene. The penetration is monitored by measuring the differential capacitance of the monolayer; the uptake of PAH causes a potential shift (up to ?0.25 V) in the cathodic capacitance peaks. This occurs without displacement of the lipid from the mercury. The differential capacitance is measured by out-of-phase (90°) a.c. voltammetry and rapid cyclic voltammetry. The PAH permeate the mercury-adsorbed lipid layers from dilute aqueous solution; the order of affinity is benzo[a]anthracene > fluoranthrene = pyrene > anthracene = phenanthrene. The rates of penetration vary for the different compounds and depend on their water solubility.     

The impact of the cononsolvency effect on poly (N-isopropylacrylamide) based microgels at interfaces

The paper addresses the effect of solid interfaces on the cononsolvency effect for poly(N-iso propylacrylamide) based microgels containing different contents of the co-monomer allyl acetic acid (AAA). The cononsolvency effect is studied by dynamic light scattering (DLS) in solution and with atomic force microscopy (AFM) at surfaces against different mixtures of water and organic solvent (ethanol, iso-propanol, and tetrahydrofuran). For the studies at interfaces, the microgels are spin coated on silicon wafers that are precoated with poly(allylamine hydrochloride) (PAH). The minimum in particle volume due to cononsolvency shows a pronounced shift from 10–20 % of organic solvent to 40–50 % after deposition at the Si/PAH wafer. The strong shift indicates an increase of water to organic solvent ratio within the gel at the surface with respect to the bulk solution. In order to understand the increase of water to organic solvent ratio, shrinking/reswelling AFM experiments for different spin-coating conditions and under ambient conditions are carried out. Spin coating from water instead from different solvent mixtures has no effect on the cononsolvency. In ambient conditions, the cononsolvency effect disappears