Atomic absorption spectrometric determination of selenium with carbon furnace atomization

A Varian Techtron model 63 carbon rod atomizer is used for the atomic absorption spectrometric determination of nanogram quantities of selenium. The pronounced interferences from the matrices in biological digests can be obviated by isolating selenium from sample matrices by precipitation with ascorbic acid. The precision of the determination is improved by incorporating 5000 μg Ni ml^?1 in the analytical solutions. Selenium at μg g^?1 and sub-μg g^?1 levels in a variety of biological samples can be determined. The detection limit is 25 ng Se g^?1.     

On-line preconcentration of trace copper for flame atomic absorption spectrometry using a spherical cellulose sorbent with chemically bound quinolin-8-ol

Preconcentration was effected using a 50 mm × 2 mm i.d. minicolumn packed with a spherical cellulose sorbent with chemically bound quinolin-8-ol function groups (Ostorb Oxin). The column was connected to the nebulizer of the atomic absorption spectrometer and the sample solution and eluent (2 M hydrochloric acid) were sucked through it at a flow-rate of 2–3 ml min^?1 by utilizing the negative pressure of the nebulizer. The experimental design was tested with the determination of traces of copper. Peak-area and peak-height measurements were compared. Owing to the simple calibration, the former method was used for quantification. The dynamic range was from 0.3 ng ml^?1 (detection limit) to 5 μg ml^?1 (breakthrough). The reproducibility in the concentration range 25 ng ml^?1-5 μg ml^?1 was better than 5%. Water-soluble inorganic salts, ammonia and sodium hydroxide were analysed. The accuracy of the results was checked by anodic-stripping voltammetry and by electrothermal AAS.     

A Fluorosensor with Immobilized Cyclodextrin As A Substrate

Abstract

A flow-through optosensor for phenylalanine and tyrosine is described in this paper. The sensor is developed in conjunction with a flow-injection analysis system and uses immobilized β-cyclodextrin as the sensing agent. The analytical performance characteristics of the proposed sensor for analysis of very low levels of phenylalanine and tyrosine were as follows: the detection limits for phenylalanine and tyrosine were 0.20 μg ml^?1 and 8.9 ng ml^?1, respectively. The observed relative standard deviations were 1.03% for 50 μg ml^?1 of phenylalanine (n = 7) and 3.6% for 0.1 μg ml^?1 of tyrosine (n = 7), respectively.     

Inductively-coupled plasma atomic emission spectrometric determination of boron based on generation of methyl borate

Boron is converted to methyl borate, distilled and condensed, and selectively volatilized at 50°C into the plasma without interference from methanol, which quenches the plasma. The 3σ detection limit is 40 ng ml^?1 boron, the calibration graph is linear up to 10 μg ml^?1 and the r.s.d. 3.0% for 2.0 μg ml^?1 (n = 10). Boron is determined in plant-tissue and steel standards.     

Ion-Associates of Alkaloids and Synthetical Psychopharmaca With Cresol Red.

Abstract

Ethylmorphine, morphine, codeine, cocaine, sernyl (PCP), LSD, 3-quinuclidinyl benzilate (BZ) provide, together with Cresol Red, ion-associates that are extractable by chloroform. The extracts of the ion-associates prove the absorption maxima in the interval 405 to 415 nm. Maximum extraction of the analytes of the ion-associates is reached after 4 minutes, taking readings of different pH values in 4 intervals of 1.5. This method allows detect of alkaloids and synthetical psychopharmaca row of quantities between 0.45 μg.ml^?1 and 1.55 μg.ml^?1 and to determine 1.05 μg.ml^?1 to the amount 2.99 μg.ml^?1 of the analytes in the aqueous solutions.     

Atomic absorption spectrometric studies of the atomization of boron from a carbon rod atomizer

Boron (<20 μg ml^?1) in aqueous solutions gives no absorbance but addition of ascorbic acid, especially with titanium greatly enhances the signal, leading to a detection limit of 0.2 μg ml^?1 boron. The presence of uranium (<10 mg ml^?) only slightly decreases the boron signal.     

Characterization and application of silylated substrates for the preconcentration of cations

Chelating functional groups immobilized on silica and controlled pore glass beads are used to preconcentrate cations from aqueous solution in the concentration region of ng ml^?1. The functional groups are chemically bonded to the substrates by silylation reagents which may be employed as received or further modified. For example, commercially available 1,2-diamines may be used or converted to the dithiocarbamate after immobilization. This report includes studies of ionic strength and sodium chloride effects on the recovery of transition metal ions. Batch extraction of transition metal ions is accomplished with silica as the substrate for solutions containing transition metal ions at μg ml^?1 concentrations. Column extraction of solutions pumped at 50 ml min^?1 is accomplished at concentrations of 25 ng ml^?1. Recovery is good in both cases. The cations were determined directly on pelletized substrates by x-ray fluorescence. However, the ions may be eluted from the substrate and determined by other methods. Examples of determinations of several cations in lake water and high-purity industrial water are given.     

Determination of urinary chromium levels for healthy men and diabetic patients by electrothermal atomic absorption spectrometry

Urinary chromium levels for healthy and diabetic men were determined by direct graphite-furnance atomic absorption spectrometry. The average values were 0.72 ± 0.31 ng ml^?1 for 23 healthy men aged 23 to 35, 0.39 ± 0.19 ng ml^?1 for 19 healthy men aged 47 to 69, and 1.0 ± 0.9 ng ml^?1 for 23 diabetic patients aged 13 to 79. Some urines of diabetic patients exhibit values > 1.3 ng ml^?1, which are never found in healthy men. The proposed method involves direct injection of 20 μl of urine inot a pyrolytically-coated graphite tube, and a standard addition calibration procedure involving a pooled urine sample. The results are compared with those obtained by a liquid-liquid extraction method.     

Spectrophotometric Studies on the Proton Transfer from the Protonated DNA to 5,10,15,20-Tetrakis[4-(trimethyammonio)-phenyl]porphine

Abstract

The interaction of nucleic acids with 5, 10, 15, 20-tetrakis[4-trimethy-ammonio)phenyl]porpine (TAPP) were investigated on the basis of a mechanistic discussion, and a spectrophotometric method for DNAs was accordingly proposed in the present paper. Depending on the acidity of the solution, TAPP can interact with nucleic acids, producing different absorption features. When the pH of the solution is higher than 6.39, TAPP can interact with both DNAs and RNA, giving a new absorption band at 420.3 nm. If the pH is lower than 6.39, however, the interactions with DNAs (but not RNA) can give an absorption band centered at 436.3 nm. It was found that the absorption band at 436.3 nm originates from the proton transfer from the protonated double-stranded structure of DNA to TAPP. At optimal conditions, the absorbance at 436.3 nm is in proportion to the concentration of the DNAs. Calibration curves were linear in the range of 0±3.0 μg.ml^?1 for calf thymus and 0±3.2 μg.ml^?1 for fish sperm DNA. No interference of 4-fold of RNA was found for the determination of DNAs. The limits of determination (3[sgrave]) were 34.6 ng.ml^?1 for calf thymus DNA and 33.2 ng.ml^?1 for fish sperm DNA, respectively. Four synthetic samples were determined with satisfaction.     

Fluorimetric determination of mebendazole and flubendazole in pharmaceutical dosage forms after alkaline hydrolysis

The selective and very sensitive fluorimetric determination of mebendazole and flubendazole is based on alkaline hydrolysis and adsorption on Whatman 42 filter paper. Limits of detection are 0.1 μg ml^?1 and 0.5 μg ml^?1, respectively, with linear response sponse up to 10 μg ml^?1 and 50 μg ml^t?1. The fluorescence produced is very stable (λ_em = 460 nm) and the method is applicable to anthelmintic pharmaceutical preparations.     

Voltammetric behaviour of ascorbic acid at a graphite—epoxy composite electrode chemically modified with cobalt phthalocyanine and its amperometric determination in multivitamin preparations

Cyclic voltammetry was used to investigate the electrochemical behaviour of ascorbic acid at a carbon—epoxy composite electrode modified with the electron mediator cobalt phthalocyanine. The modified electrode reduced the overpotential necessary for the oxidation of the vitamin by approximately 150 mV to 0.21 V vs. The saturated calomel electrode; the process was dependent on the pH of the supporting electrolyte, but independent of ionic strength over the range studied. The relative standard deviation (r.s.d.) of the peak heights of the cyclic voltammograms was 0.81% for a 1 × 10^?4 M ascorbic acid solution (n = 7). The optimum supporting electrolyte was found to be 0.05 M phosphate buffer (pH 5).Amperometry in stirred solutions was then done at an applied potential of +0.25 V. The limit of detection was 0.65 ng ml^?1 and the calibration graph was linear in the range 175 ng ml^?1?50 μg ml^?1. The method was used to determine ascorbic acid concentrations in single- and multivitamin preparations; the recovery was 97.86% for the vitamin added to one preparation. The r.s.d. for the analyses in these samples was about 5%. For comparison, the vitamin was also determined in these tablets using LC with UV detection at 254 nm; the correlation coefficient for the levels determined was 0.9989 (p = 0.0007).     

Rapid spectrophotometric determination of ruthenium(III) with prochlorperazine maleate

A rapid, simple spectrophotometric method for the determination of μg amounts of ruthenium, based on the formation of a pink complex between the metal and prochlorperazine maleate (PCPM) in sulphuric or hydrochloric acid solution, is described. The complex has an absorption maximum at 530 nm and its molar absorptivity is 6.733·10³ l mol^?1 cm^?1. The sensitivity is 0.0151 μg Ru cm^?2 for log I_o/I = 0.001. Beer's law is valid over the range 0.2–10 μg Ru ml^?1 ; the optimal range for spectrophotometric determination is 0.8–8.0 μg Ru ml^?1. Job's method of continuous variation, the mole ratio method and the slope ratio method indicate a 1:1 composition for the complex. The effects of acidity, time, temperature, order of addition of reagents, reagent concentration, and the interferences from various ions are reported.     

Determination of vanadium and titanium in steel by inductively coupled plasma atomic emission spectrometry with modified use of a tungsten boat furnace atomizer for atomic absorption spectrometry

For electrothermal sample introduction, a commercially available tungsten boat atomizer for atomic absorption spectrometry (AAS) was transferred to a vaporizer for inductively coupled plasma atomic emission spectrometry (ICP-AES). The modification retained as much of the original design of the atomizer as possible, so that the apparatus could be switched easily between conventional tungsten boat furnace (TBF)-AAS and TBF-ICP-AES. By using this system, a procedure for the determination of vanadium and titanium in steel was investigated. The detection limits (S/N=3) of vanadium and titanium were 3.9 and 1.5 ng ml^?1, respectively. The relative standard deviations for five replicate determinations were ca. 3% for both elements. The calibration graphs were linear up to 100 μg ml^?1 vanadium(V) and 10 μg ml^?1 titanium(IV). Results of analyses of some low-alloy steel samples are given.     

Integrated Retention/Spectrophotometric Detection Method for the Determination of Formaldehyde

Abstract

An integrated-sensor method for the determination of formaldehyde based on retention of the reaction product of the analyte with p-rosaniline and sulfite in a flow-cell packed with Dowex 1-X-8 anion exchange resin was developed. The method has a good selectivity with a detection limit of 0.3 μg ml^?1 (1 ml sample) or 75 ng ml^?1 (2 ml sample), and a linear range between 1–30 μg ml^?1. The relative standard deviations (n = 11) were 2.8 and 1.3% for 2 and 20 μg ml^?1 formaldehyde, respectively. Depending on the working conditions, the sampling frenquency ranged between 10 and 18 h^?1. The method was applied to the determination of formaldehyde in well water.     

Indirect determination of vanadium by atomic absorption spectrometry

An indirect method for the determination of vanadium as vanadate by atomic absorption spectrometry is described. In neutral medium, vanadate forms a stable ion-association complex with copper (II) and biguanide, which is extractable into butanol with an efficiency higher than 99%. The copper content in the extract (and hence indirectly VO^?₃) is determined by aspirating it directly into an acetylene flame. The calibration graph is linear up to 3.4 μg ml^?1 of VO^?₃. The limit of detection is 16 ng ml^?1. Only chromium interferes.     

Indirect atomic absorption spectrometric determination of perchlorate by liquid-liquid extraction in a flow-injection system

The determination is based on the continuous liquid-liquid extraction of the copper(I)/6-methylpicolinealdehyde azine/perchlorate ion-pair into 4-methyl-2-pentanone in a flow-injection manifold. The organic fills a loop of an injector situated in an integrated feed system of an atomic absorption spectrometer. Measurement of the copper atomic absorption signal from the organic phase allows the indirect determination of 0.5–5 μg ml^?1 perchlorate, giving a 3-fold increase in sensitivity over the conventional spectrophotometric method. The detection limit is 70 ng ml^?1. The sampling frequency is 45 ± 5 h^?1. The method is highly selective, and has been used for the determination of perchlorate added to serum and urine samples.     

Simultaneous determination of free and EDTA-complexed copper ions by flame atomic absorption spectrometry with an ion-exchange flow-injection system

A simple method is described for the simultaneous determination of free and complexed copper ions in a flow-injection system comprising ion-exchange and flame atomic absorption spectrometry. Sampling rates for 400-μl samples were 90 h^?1. Typical relative standard deviations for the simultaneous determinations were 1.6% for the complexed metal (0.50 μg ml^?1) and 1.0% for the free metal (0.20 μg ml^?1).     

Flow Injection Analysis of Famotidine with Spectrophotometric Detection

Abstract

A flow injection determination of famotidine has been described. The method is based on the reaction of the drug with cupric acetate to form a blue coloured complex which shows absorption maxima at 314 nm and 630 nm. For an injection volume of 100 μl calibration graphs were rectilinear from 10- 50 μg. ml^?1 and 50–500 μg.ml^?1 of drug at the two wavelengths respectively. Samples could be analysed at rates upto 60 per hour with a relative standard deviation less than 1.4%. The method was evaluated by analysis of the pure drug and commercial formulations. The results compare well with those obtained by official methods.     

Phosphorescence detection in flowing systems: selective determination of aluminium by flow-injection liquid room-temperature phosphorimetry

The concept of the micelle stabilized liquid room-temperature phosphorescence (MS-LRTP) was applied to the determination of a metal (aluminium) in a flowing system. A three-line flow-injection manifold was developed and various parameters were optimized. A linear calibration graph was obtained for 0–4 μg ml^?1 aluminium. The limit of detection was 50 ng ml^?1 and the relative standard deviations for 0.1 and 1.0 μg ml^?1 aluminium were 2.7 and 1.3% respectively. The proposed procedure is fairly selective. More than 20 common ions studied did not interfere with the determination of aluminium or could be masked by appropriate reagents. The flow-injection method proposed was applied without any preliminary separation to the determination of aluminium in simulated synthetic samples in water and in clinical samples of particular importance in the control of aluminium toxicity in renal failure patients.     

Determination of arsenic at the picogram level by atomic absorption spectrometry with miniaturized suction-flow hydride generation

A continuous-flow hydride generator is modified and miniaturized for the determination of picogram amounts of arsenic by atomic absorption spectrometry. A 300-μl sample is dropped into a teflon cup and pumped into an alkaline sodium tetrahydroborate stream, which is acidified in a reaction coil. The evolved hydride is swept with argon through a phase separator into an electrically-heated quartz absorption cell and the absorbance is recorded. To eliminate differences in sensitivity between arsenic(III) and arsenic(V) without prereduction by potassium iodide, it is important that arsenic(V) be mixed with tetrahydroborate prior to mixing with hydrochloric acid. The method has a detection limit of 0.08 ng As ml^?1 (24 pg) and the calibrations is linear up to 50 ng As ml^?1. The relative standard deviation for 10 replicate measurements is 5.4% for 0.5 ng As ml^?1. The addition of potassium iodide and hydroxylamine is confirmed to be effective in minimizing some interferences. The sampling rate is 90 h^?1. Results for NBS biological and steel reference materials demonstrate applicability of the technique.