Continuous flow extraction of indium with bis(2-ethylhexyl)phosphoric acid in 4-methylpentane-2-one coupled on-line with flame atomic absorption spectrometry

Extraction in liquid-liquid segmented flow is used for preconcentration of indium from dilute nitric acid solutions into bis(2-ethylhexyl)phosphoric acid dissolved in 4-methylpentane-2-one. The extraction setup is coupled on-line with flame spectrometry to give a fully mechanized system. The detection limit of the method is 0.03 mg l^?1, the calibration plot is linear up to 1.75 mg l^?1. Repeatability is 1.5% RSD measured at 1 mg l^?1. Sample throughput is 60 h^?1.     

Spectrophotometric determination of vanadium(V) with methoxypromazine maleate and its application to vanadium steels and minerals

The reagent in 8-fold excess forms a violet species with vanadium(V) instantaneously in 1–3 M phosphoric acid. The absorption maximum is at 565 nm; the molar absorptivity is 1.65 × 10⁴ l mol^?1 cm^?1. Beer's law is obeyed over the range 0.1–6.5 mg l^?1 vanadium (V); the optimum range is 0.3–6.0 mg l^?1; the Sandell sensitivity is 3.1 ng cm^?2. The method is simple and selective. The method is applicable for the determination of vanadium in vanadium steels and minerals.     

A comparison of some flame atomic absorption spectrometric methods for the determination of cadmium in fertilizers and related materials

A liquid-liquid extraction procedure for cadmium in phosphate rock and phosphate-based fertilizers is described. Extraction with tri-n-octylamine and potassium iodide into methyl isobutyl ketone is shown to be simpler and less prone to interferences than the more commonly used methods based on ammonia pyrrolidine-dithiocarbamate. Iron interest strongly in the dithiocarbamate method. Addition of ascorbic acid, and extraction at low pH allows the dithiocarbamate method to operate up to 0.15 g Fe l^?1, while the amine method tolerates at least 0.2 g Fe l^?1. Direct determination is suitable on samples with a sufficiently high cadmium content. The amine extraction method has been applied successfully at an apatite containing only 0.03 mg kg^?1 cadmium.     

Spectrophotometric determination of micro amounts of cationic polymeric flocculants by flow injection analysis

Cationic polymeric flocculants in water are determined spectrophotometrically with the anionic compound 3-(2-hydroxy-3-carboxyanilide-1-azonaphthalene)-4-hydroxybenzenesulfonic acid at pH 10 by flow injection analysis. The calibration graph at 680 nm is rectilinear from 0 to 20 mg l^?1 under optimal conditions. The relative standard deviation for 20 injections of Cat-Floc (10 mg l^?1) was 1.2%; the sample throughput was 60 h^?1.     

Comparison of four chromogenic reagents for the flow-injection determination of aluminum in water

Pyrocatechol violet (PCV), aluminon, eriochrome cyanine R (ECR) and eriochrome cyanine R with cetyltrimethylammonium bromide (ECR/CTA) are compared as chromogenic reagents for the flow-injection determination of aluminium in water. The detection limit of the ECR/CTA method is 1 μg Al 1^?1. The detection limits of the PCV and ECR methods are 5 μg Al 1^?1. The aluminon method is the least sensitive, with a detection limit of 50 μg Al l^?1. Interference from iron, fluoride, phosphate and the acidity of the sample were investigated. The interference from iron is suppressed by hydroxylammonium chloride/1,10-phenanthroline in the PCV and ECR/CTA methods at concentrations less than 5 mg Fe l^?1. In the ECR and aluminon methods, iron <5 mg l^?1) is masked by ascorbic acid. Fluoride at <0.2 mg l^?1 can be tolerated in all methods. The aluminon method can tolerate up to about 500 mg l^?1 in the three other methods. All methods are sensitive to changes in acidity of the samples; the acidity should be 0.08–0.12 M HCl.     

Determination of a non-ionic surfactant in aqueous environmental samples by flow-injection analysis with chemiluminescence detection

A flow-injection procedure for the determination of a commercially available fatty amine ethoxylate-based non-ionic surfactant in sea water over the range 0–50 mg l^?1 is described. The procedure is based on measurement of the chemiluminescence emission resulting from oxidation of the tertiary amine group with sodium hypochlorite at pH 10.5 in the presence of Rhodamine B, which acts as a sensitizer.     

Simultaneous spectrophotometric determination of calcium and magnesium with chlorphosphonazo-III by flow injection analysis

In this flow-injection method, the total concentration of calcium and magnesium is determined by using triethanolamine/hydrochloric acid buffer (pH 7.0) and chlorphosphonazo-III (CPA-III) in the flow streams, and the concentration of calcium alone is determined by using 1.6×10^?3 M hydrochloric acid and CPA-III in the flow treams. At pH 7.0, medium, the linear calibration ranges were 0–2.00 mg l^?1 for both calcium and magnesium and the detection limits were each 0.02 mg l^?1; at pH 2.2, the linear calibration range for calcium and the detection limit were 0.20–2.00 mg l^?1 and 0.1 mg l^?1, respectively. Injection rates are 200 h. The method is suitable for analyzing natural waters.     

Flow-injection analysis for power plants: Evaluation of detectors for the determination of control parameters in conditioned water—steam cycles

Flow-injection methods are described for monitoring water in power-plant cycles. The parameters considered are pH (in the range 5.5–9.5), using a flat-headed combined electrode, ammonia (0.2–3 mg N l^?1), using Nessler, Berthelot and gas-diffusion methods, hydrazine (0.025–0.3 mg l^?1), using the dimethylamino-4-benzaldehyde method, copper (0.02–0.2 mg l^?1), using bathocuproin and methods based on ion-selective electrodes, iron (0.01–10 mg l^?1), using phenanthroline, ferrozine and biamperometric methods, and silicon (0.02–0.1 mg l^?1), using the heteropoly blue complex, with two different types of reducing agent [tin(II) chloride and ascorbic acid]. The parameters considered were precision, analysis frequency and application range. The results obtained showed that flow-injection methods perform well in terms of sensitivity and analysis frequency and suggested the possibility of transferring this methodology to analytical systems in power plants.     

Reactions between technetium(VII) and some hydrazones and the spectrofluorimetric determination of technetium(VII) with 2,2′-dipyridylketone hydrazone

The reactions between pertechnetate and five hydrazones are described. Of these, the technetium(VII)/2,2′-dipyridylketone hydrazone system was found to be most sensitive, and is studied in detail. Spectrofluorimetric procedures for the determination of technetium(VII) over the range 0.01–12 mg l^?1 are reported. The reaction proceeds most favourably under acidic conditions (1.4 M hydrochloric acid). For 1 mg l^?1 technetium(VII), 100 mg l^?1 levels of U(VI), Re(VII), Mo(VI) or W(VI) do not interfere when the reaction proceeds at room temperature. Sensitivity improves at higher temperatures.     

Study of the solubility of antimony in mercury by cyclic and stripping voltammetry

The solubility of antimony in mercury has been studied by cyclic and stripping voltammetry in solutions of Sb(III) in 4 M HCl. The solubility has been evaluated at 8.57×10^?4 mol l^?1 or 1.27×10^?3 at. % at 25°C which agrees well with solubility values derived from data reported by other authors at different temperatures. A solubility heat (H_sol) of 16.7 kJ mol^?1 was calculated.     

Effects of iron on the degradation of triphenyltin by pyoverdins isolated from Pseudomonas chlororaphis

The yellow compound pyoverdin was isolated from the bacteria Pseudomonas chlororaphis, isolated from mud in Japan. A study of the effects of iron, phosphorus, manganese and zinc on degradation of triphenyltin (TPT) by pyoverdin (20 mg) was carried out in distilled water (30 ml) containing 6 µg l^?1 concentration of TPT at 20 °C for 48 or 96 h. The organotins in water were analyzed by gas chromatograph–mass spectrometry in the selected ion mode. The degradation of TPT by pyoverdin decreased with increase of phosphorus at 0–35 mg l^?1 and Fe‐EDTA at 0–2 mg l^?1 concentrations. Also, degradation of diphenyltin by pyoverdin decreased with increase of Mn‐EDTA at 0–1 mg l^?1 and Zn‐EDTA at 0–1 mg l^?1. On the other hand, degradation of TPT by pyoverdin was found to be unaffected by manganese and zinc in water. Copyright © 2002 John Wiley & Sons, Ltd.     

Flow-injection spectrophotometric determination of aluminium in water with pyrocatechol violet

Optimum conditions for the adaptation of the spectrophotometric pyrocatechol violet method for aluminium to a flow-injection system are described. The detection limit is 3 μg Al l^?1 and calibration graphs are linear up to 3 or 10 mg l^?1 (with 200-μl or 10-μl injection loops, respectively). The relative standard deviation is 〈 2% at 0.1 mg Al l^?1. Potential interferences of 40 common inorganic ions and of 20 organic substances, including fulvic acid, are reported. With the use of conventional masking agents and predigestion of samples with high organic content, the method is suitable for determining total aluminium in natural waters.     

Utilisation of kinetic-based flow injection methods for the determination of chlorine and oxychlorine species

Automated selective iodometric methods for the determination of chlorine and oxychlorine species have been developed for use in the drinking water industry. By utilising kinetic-based methods, linear ranges observed were: chlorine, 0.2–10 mg l^?1; chlorine dioxide, 0.3–10 mg l^?1; chlorite ion, 0.08–5 mg l^?1; and chlorate ion, 0.08–5 mg l^?1.     

Flow-injection technique for the determination of low levels of phosphorus in natural waters

An inexpensive flow-injection instrument for determining low concentrations of dissolved reactive phosphorus in natural waters is reported. The unique feature is the use of an inexpensive detector consisting of a flow cell and a simple photometer that incorporates a super-bright light-emitting diode as the source and a photodiode as the detector. The tin(II) chloride-molybdate method was optimized using a modified simplex optimization method. Silicate interference up to 5 mg Si l^?1 was removed by addition of 0.10% (w/v) tartaric acid. Using the tartaric acid-modified optimized reagents, a detection limit of 0.6 μg P l^?1 was achieved. The method was linear over the range 0–100 μg P l^?1 with an excellent precision (r.s.d. 2.9% at 2.0 and 0.5% at 50 μg P l^?1). An in-line pre-concentration anion-exchange column was used to obtain an even lower detection limit of 0.1 μg P l^?1 and applied to the analysis of real samples.     

Plant Regeneration Through Callus Organogenesis and True-to-Type Conformity of Plants by RAPD Analysis in Desmodium gangeticum (Linn.) DC.

An efficient plant regeneration protocol was established for an endangered ethnomedicinal plant Desmodium gangeticum (Linn.) DC. Morphogenic calli were produced from 96 % of the cultures comprising the immature leaf explants on Murashige and Skoog (MS) medium supplemented with 2,4-dichlorophenoxyacetic acid (4.0 mg?l^?1) in combination with 6-benzylaminopurine (BA; 0.8 mg?l^?1). For callus regeneration, various concentrations of BA (1.0–5.0 mg?l^?1) or thidiazuron (TDZ; 1.0–5.0 mg?l^?1) alone or in combination with indole-3-acetic acid (IAA; 0.2–1.0 mg?l^?1) were used. Highest response of shoot regeneration was observed on MS medium fortified with TDZ (4.0 mg?l^?1) and IAA (0.5 mg?l^?1) combination. Here, 100 % cultures responded with an average number of 22.3 shoots per gram calli. Inclusion of indole-3-butyric acid in half MS medium favored rooting of recovered shoots. Out of 45 rooted plants transferred to soil, 40 survived. Total DNA was extracted from the leaves of the acclimatized plants of D. gangeticum. Analysis of random amplified polymorphic DNA using 13 arbitrary decanucleotide primers showed the genetic homogeneity in all the ten plants regenerated from callus with parental plant, suggesting that shoot regeneration from callus could be used for the true-to-type multiplication of this plant.     

Determination of Ammonia in Water Using Flow Injection Analysis with Automatic Pervaporation Enrichment

Abstract

An automated ammonia monitoring system has been developed by putting a pervaporation unit in an enrichment cycle used in flow injection analysis mode. In the proposed system, an enrichment cycle was equipped to enable the adjustment for the measuring range of ammonium by controlling the duration of the enrichment circulation. Therefore, the system was capable to determine ammonia in both the surface water with low ammonia concentration and the ammonia-rich wastewater with the linear dynamic range of 0.05–15 mg l^?1 and 15–50 mg l^?1, respectively. The relative standard deviations were less than 1.9% and the quantification limit is as low as 0.03 mg l^?1. The sampling frequency is 8–10 h^?1.     

The determination of chlorinated long-chain paraffins in water,sediment and biological samples

Methods are described for the routine determination of traces of industrial chloro-n-paraffins having 13–30 carbon atoms and chlorine contents of 42–45% (frw/w), in environmental samples of water, sediments and biota. The procedures are based on thin-layer chromatography detection and measurement. All samples are cleaned up by liquid—solid adsorption chromatography and thin-layer chromatography but those rich in lipids require preliminary solvent extraction. The methods distinguish between chloro-n-paraffins based on long carbon chains (C₂₀–C₃₀) and those based on shorter chains (C₁₃–C₁₇). The methods cover the ranges 500 ng l^?1 to 8 μg l^?1 for water (i.e. from about the solubility limit upwards) and 50 μg kg^?1 to 16 mg kg^?1 for sediments and biota. The precision of the methods ranges from ± 50% relative at the lowest concentrations to ± 12% relative at the highest. Recoveries are about 90% for water, 80% for sediments and between 80 and 90% for biota according to sample type.     

Reactive Extraction of Citric Acid Using Tri-n-octylamine in Nontoxic Natural Diluents: Part 1—Equilibrium Studies from Aqueous Solutions

Use of cheap, nontoxic, and selective solvents could economically provide a solution to the recovery of carboxylic acids produced by the bioroute. In this regard in the present paper, reactive extraction of citric acid was studied. Problems encompassing the recovery of the acid ([H₃A] _aq ^o ?=?0.1?C0.8) was solved by using tertiary amine (tri-n-octylamine, TOA) in natural diluents (rice bran oil, sunflower oil, soybean oil, and sesame oil). TOA was very effective in removal of acid providing distribution coefficient (D) as high as 18.51 (E%?=?95?%), 12.82 (E%?=?93?%), 15.09 (E%?=?94?%), and 16.28 (E%?=?94?%) when used with rice bran oil, sunflower oil, soybean oil, and sesame oil, respectively. Overall extraction constants and association numbers for TOA + rice bran oil, TOA + sunflower oil, TOA + soybean oil, and TOA + sesame oil were evaluated to be 35.48 (mol/l)^?1.46, 29.79 (mol/l)^?1.30, 33.79 (mol/l)^?1.51, and 37.64 (mol/l)^?1.65 and 1.46, 1.30, 1.51, and 1.65, respectively. Specific equilibrium complexation constants (K _E(n/m)) were also predicted using mathematical modeling.     

Determination of lead in whole blood with a simple flow-injection system and computerized stripping potentiometry

An automated (24 samples/hour) procedure is described for the determination of lead (0–1000 μg l^?1) in human blood based on flow-injection stripping potentiometry. The samples are diluted 20-fold with 0.5 M hydrochloric acid containing 100 mg l^?1 mercury and 40 μg l^?1 cadmium (II), and a 1.1 ml aliquot is injected into the flow system. With a mercury-coated carbon fibre as working electrode, lead (II) is determined by using cadmium (II) as internal standard and a calibration graph prepared from bovine blood. Analyses of two human blood reference samples yielded results of 335±37 and 691±24 μg l^?1 lead, the certified values being 332 and 663 μg l^?1, respectively.     

Determination of gold by atomic absorption spectrometry after extraction into the non-desulphurized fraction of crude oil distillate

The extraction of gold from aqueous chloride solutions into non-desulphurized fractions of crude oil distillates, especially paraffin oil, is described. The fraction boiling at 150–220°C exhibited optimum properties. The extraction is tested for solutions containing chlorides, dissolved chlorine and 0.1–3 M hydrochloric acid. Nitric acid should be absent. The distribution coefficient of gold varies from 400 to 900. Extracts containing ? 0.3 g l^?1 gold are stable for at least 12 months. The organic extract is sprayed into a lean acetylene/air flame with measurement at 242.8 nm (background correction). The calibration graph has linear portions over the ranges 0–2.5 and 2.5–16 mg l^?1. The limit of detection is 0.03 mg l^?1 gold in the extract (0.001 mg l^?1 in the aqueous phase). The minimum measurable concentration for gold in auriferous rocks and ores is 0.018 g per ton with 25-g samples.