Newtonian behavior of a styrene–butadiene–styrene block copolymer

The melt rheological behavior of an anionically polymerized styrene–butadiene–styrene (SBS) block copolymer sample (S: 7 × 10³ and B: 43 × 10³) was studied using a Weissenberg rheogoniometer. Highly non-Newtonian behavior, high viscosity and high elasticity, which are characteristics of ABA type block copolymers, were observed at 125°C, 140°C, and 150°C. The data at these temperatures superimposed well onto a master curve giving a constant flow activation energy. However, the data at 175°C indicated a marked change in the flow mechanism between 150°C and 175°C. At 175°C, the sample showed Newtonian behavior, negligible elasticity, and deviation from the master curve. These findings may be considered as an indication that the SBS block copolymer sample undergoes a structural change from a multiphase structure at low temperatures into a homogeneous structure at some temperature between 150°C and 175°C.     

Structure and properties of a styrene–butadiene–styrene block copolymer

Electron-microscopic texture and physical properties of a styrene–butadiene–styrene (SBS) block copolymer obtained by casting from toluene, carbon tetrachloride, ethyl acetate, and methyl ethyl ketone are discussed. Two peaks are observed in the mechanical loss (tan delta;) curve at ?70 and 100°C which are attributed to segmental motion of polybutadiene and polystyrene, respectively. The polybutadiene peak heights are in the order of solubility in the solvent used; the polystyrene peak heights are in converse order. In addition to these peaks, a third peak is observed at 10°C for specimens cast from ethyl acetate or methyl ethyl ketone. A transition corresponding to this peak is also noticed in thermal analysis. It is proposed that aggregation of styrene blocks is relatively incomplete in specimens cast from solution in poor solvents.     

Nature of melt rheological transition in a styrene–butadiene–styrene block copolymer

Our laboratory previously reported the observation of a high temperature, melt rheological transition in a styrene–butadiene–styrene (S:7 × 10³ and B:43 × 10³) block copolymer from the highly elastic, nonlinear viscous behavior typical of a multiphase structure to linear viscous behavior with insignificant elasticity typical of a single-phase structure. We have investigated the precise nature of this melt rheological transition in the 7S-43B-7S sample by measuring the dynamic viscoelastic properties at more than 11 temperatures, including several in the transition region. A new procedure was developed for accurately measuring the sample temperature in a Weissenberg rheogoniometer. The transition is found to start at about 140°C and proceed over a narrow transition region from 140 to about 150°C. Data at all temperatures superimpose onto a single master curve only at high reduced frequencies. At low reduced frequencies, two characteristic branches of the master curve are formed. The data at temperatures below the transition region superimpose onto the upper branch where the dynamic viscosity η′(ω) is a strong function of ω, whereas the data at temperatures above the transition region superimpose onto the lower branch where η′(ω) is independent of ω. The data at temperatures within the transition region fall between the upper and lower branches, ordered according to their temperature positions. The apparent flow activation energy is found to be constant at about 22.8 kcal/mole below the transition region, but appears to decrease to about 17.4 kcal/mole above the transition region. The narrowness of the rheological transition far above the glass transition temperature of the polystyrene domains and the limiting linear viscoelastic behavior at low frequencies above the transition suggest an accompanying morphological transition rather than a gradual weakening of the polystyrene domains.     

Epoxidation of styrene–butadiene–styrene block copolymer and use for gas permeation

The epoxidation of styrene–butadiene–styrene triblock copolymer (SBS) by an in situ generated peracid method is discussed. The presence of an acid acting as catalyst led to side reaction. The reactivities of internal double bonds (the 1, 4-structure) were higher than those of the vinyl bonds (the 1, 2-structure). In the 1, 4-structure, the reactivities of cis-structure were higher than those of trans-structure. The oxirane weight content and total oxygen weight content were determined by titration and element analysis, respectively. The cohesive energy, solubility parameter, and the glass transition temperature of epoxidized SBS increased with increasing total oxygen weight content. But the molecular weight between crosslinking points decreased resulting in an increase of crosslinking density with increasing total oxygen weight content. The changes of properties of epoxidized SBS reduced the gas permeability of oxygen and nitrogen through epoxidized SBS membrane, but increased the gas selectivity between oxygen and nitrogen. When the operating temperature of gas permeation was increased, the permeability of oxygen and nitrogen increased but the selectivity decreased. For epoxidized SBS containing 7.35 wt % oxygen content, the activation energy was 9 and 12.2 kcal/mol for oxygen and nitrogen, respectively.     

Effect of morphology on the mechanical and rheo-optical properties of a styrene–butadiene–styrene block copolymer

The mechanical and rheo-optical properties of a styrene–butadiene–styrene block copolymer of a given chemical composition are dependent upon the morphology of the polymer as affected by the solvent system from which a polymer film is cast. Films cast from methyl ethyl ketone and from toluene are compared. Properties found to differ are the stress–strain curve, the birefringence–strain curve, stress relaxation birefringence relaxation, and the dynamic mechanical spectra.     

Free radicals in electron beam irradiated blends of polyethylene and butadiene–styrene block copolymer

Two-components blends, of compositions in a range from 100% of high density polyethylene (PE) to 100% of butadiene–styrene block copolymer (SBS) were investigated from the point of view of basic radiation chemistry and modifications of technological and chemical properties. Irradiations were performed with 10 MeV electrons to doses of 30, 60 and 120 kGy, by the split dose technique to avoid thermal effects. EPR spectra were measured with the Bruker 300 ESP spectrometer, using a computer program for the deconvolution and analysis of spectra.     

Structure of styrene–butadiene–styrene block copolymers by diffusion analysis

In this study, solvent sorption was used to investigate the morphology of a styrene–butadiene–styrene (SBS) triblock copolymer. The sorption process was found to deviate from the normal Fickian character, usually found in conventional elastomer–solvent systems, because of the presence of an interfacial region for both polybutadiene and polystyrene. This interphase absorbed solvent at a temperature below its glass transition and contributed to the resulting non-Fickian time-dependent diffusion process. The equilibrium diffusion coefficient was estimated to be 3.2 × 10^?7 cm²/sec regardless of the casting surface. Nevertheless, according to the sorption measurements, the casting surface did have an effect on the approach to equilibrium. The results indicated a denser packing of the molecules and hence a decreased diffusion coefficient for Teflon and glass cast films, because of internal stresses left within the films during casting.     

Crazing in thin films of styrene–butadiene–styrene block copolymers

The mechanism of craze initiation and growth and its relationship to mechanical properties has been studied in thin films of styrene–butadiene–styrene (SBS) block copolymers. Optical microscopy and transmission electron microscopy were used to examine three copolymers which has a spherical rubber domain morphology but varied in rubber content from 20 to 50%. With increasing rubber content, the crazes became longer and less numerous. Widening of the crazes was at least partially responsible for the higher strains achieved in the copolymers, especially for the composition with the highest rubber content where the crazes widened to form micronecks. Transmission electron microscopy revealed that craze initiation and growth at the craze tip occurred by cavitation in the polystyrene phase. Cavitation of the continuous phase rather than the rubber domains was attributed to the concentration of chain-end flaws in the polystyrene. Crazes in the block copolymers followed a meandering pathway and the boundaries between crazed and uncrazed material were indistinct. Incorporation of fibrillated rubber particles into the craze fibrils strengthened the craze. At higher rubber content, the craze widened in the stress direction by voiding and fibrillation, which produced a cellular morphology.     

Steady flow and dynamic viscosity of branched butadiene–styrene block copolymers

Steady flow and dynamic viscosities were determined for symmetrical linear and starbranched block copolymers of butadiene and styrene above their upper (polystyrene) glass transition. Block structures examined were B-S-B, (B-S-)₃, S-B-S, (S-B-)₃ and (S-B-)₄. At constant molecular weight and total styrene content viscosities were greater for polymers terminating in styrene blocks, irrespective of branching. Branching decreased the viscosity of either polybutadiene-terminated or polystyrene-terminated block polymers, compared at equal M _w. However, comparisons at equal block lengths showed that the length of the terminal blocks, not the total molecular weight, governs the viscoelastic behavior of these polymers to a surprisingly good approximation. This unusual result is rationalized in terms of the two-phase domain structure of these polymers, which persists to a significant degree in the melt. Below the glass transition of the polystyrene blocks the effects of branching were masked by differences in the morphology of the domain structure unrelated to branching.     

Wavelength sensitivity of acrylonitrile–butadiene–styrene

The wavelength sensitivity of unpigmented 100 mil thick ABS exposed to sunlight and filtered xenon are radiation was determined by the sharp cut filter technique based on three types of photochemical changes: bleaching, yellowing and loss in impact strength. Bleaching of the yellow-colored species formed in the processed material is caused by wavelengths between 380 and 525 nm with maximum color change by the 475–485 nm region. Photochemical yellowing is due to wavelengths between 300 and 380 nm with all wavelengths being almost equally effective. The spectral sensitivity based on change in impact strength shifts from the UV to the visible region as photochemical yellowing progresses. Addition of two stabilizers, a benzotriazole ultraviolet absorber and a hindered amine stabilizer, shifts the wavelength sensitivity based on yellowing to wavelengths shorter than 330 nm, but has no influence on the spectral effects based on impact strength. It is postulated that the rate of yellowing is reduced mainly by the ultraviolet absorber and stabilization against loss in impact strength is due largely to the hindered amine. Differences in rates and spectral response of the three types of photochemical changes indicate that they are due to different initiating mechanisms and thus require different types of stabilization. The significance to stability testing is discussed.     

Studies on thermal degradation of acrylonitrile–butadiene–styrene copolymer (ABS-Br) containing brominated flame retardant

The thermal degradation of acrylonitrile-butadiene-styrene copolymer (ABS-Br; 10 g) containing brominated flame retardant (Br: 9.59 wt.%) was carried out at 450 °C using a semi batch operation using two different temperature programs. The heating rate was found to affect the quality of the degradation oil and yield of products (liquid, gas and residue). Data on the effect of the temperature program on the accumulation of liquid products was presented. It was found that the majority of the bromine was concentrated in the carbon residue and while majority of the nitrogen accumulates in the liquid products irrespective of degradation mode. The use of a one step constant heating rate process (I) produced a higher liquid yield (39%), than a two step process (29%). Differences were also noted in the Br and N contained in the liquids produced by the two processes.     

New anion conducting membranes based on functionalized styrene–butadiene–styrene triblock copolymer for fuel cells applications

In this work, the functionalization of polystyrene‐b‐poly(butadiene)‐b‐polystyrene triblock copolymer (SBS) with vinylbenzyl chloride and benzoyl peroxide (BPO) or α,α′‐azo‐bis‐isobutyronitrile (AIBN) as free radical initiators was reported. The functionalization degree (FD), calculated by ¹H NMR spectroscopy and confirmed by elemental analysis, was highly tunable (from 4 to 10 mol %) and positively correlated to the starting percentage of radical initiator. More specifically, at the same initiator molar percentage grafting efficiency is higher using BPO rather than AIBN. Quaternization reaction of the grafted benzyl chloride groups with the bifunctional tertiary amine 1,4‐diazabicyclo[2.2.2]octane (Dabco) led to a chemically and thermally stable homogeneous anion‐exchange membrane. Electrochemical parameters were evaluated for Dabco‐quaternized grafted copolymers having different FDs, and compared with a commercial Tokuyama benchmark membrane. Experimental data showed a positive correlation between FD and both water swelling and ionic conductivity. Best trade‐off between ionic conductivity and water swelling was found for membrane having FD 9.1 mol %, which conductivity is comparable with the Tokuyama benchmark one and water uptake is only slightly higher. The results are discussed based on the molecular parameters with particular reference to ionic content and distribution. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Membrane of epoxidized styrene–butadiene–styrene block copolymer complexing with (N,N′-disalicylideneethylenediamine) cobalt (II) and use for oxygen permeation

The complex formation reaction of epoxidized styrene-butadiene-styrene triblock copolymer (ESBS) with (N,N-disalicylideneethylenediamine) cobalt(II) (CoS) in chloroform solution is studied. The coordination number and formation constant are determined by the Miller method. The membranes of ESBS complexing with CoS (ESBS–CoS) are made by solution casting method. The kinetics of oxygen binding to ESBS–CoS membrane is studied and the equilibrium constant, association, and dissociation constant are determined. The membrane of ESBS–CoS has the affinity to absorb oxygen with reversibility and that is confirmed by the studies of DSC. Due to the reversible absorption of oxygen to ESBS–CoS, the permeation of oxygen through ESBS–CoS membrane can be explained by dual mode.     

Photodegradation of carbon monoxide–styrene copolymer in benzene and formation of block copolymer with methyl methacrylate

Photodegradation of carbon monoxide–styrene copolymer in benzene was investigated. In relation to the average number of main-chain scissions per macromolecule versus photoirradiation time, the straight line did not pass through the origin. This phenomenon was attributed to the presence of a labile bond from the carbonyl group in the main chain, in accordance with the results of Cameron and Lawrence which were found in the study of photodegradation of thermally polymerized polystyrene. In utilization of photodegradative behavior in carbon monoxide–styrene copolymer, a block copolymer of styrene with methyl methacrylate was prepared and was ascertained by precipitated fractionation, elementary analysis, and turbidimetry.     

Relationship between structures of phosphorus compounds and flame retardancies of the mixtures with acrylonitrile–butadiene–styrene and ethylene–vinyl acetate copolymer

Various analogos of phosphonic acid, phosphinic acid, and CH₃? P(O) group containing organo‐phosphorus compounds were synthesized as model compounds to investigate the effects of P content and the structure of flame retardant (FR) on their fire retarding performances of acrylonitrile–butadiene–styrene (ABS) and ethylene–vinyl acetate (EVA) copolymer. The success of synthesis was confirmed by ¹H‐ and ³¹P‐NMR. The flame retarding efficiencies were evaluated by a UL‐94 vertical test method. Thermogravimetric analysis results reveal that all the mixtures of FRs with ABS or EVA exhibit no or very little charred residues at 600°C under inert atmosphere condition, indicating that all FRs work in the gas phase rather than in the condensed phase for both ABS and EVA. The fire retarding efficiency of FR depends not only on the P content in FR but also on the nature of its structure. UL‐94 results show that P FRs with ? CH₃ group attached to the P atom exhibits the best fire retarding performance on both ABS and EVA. It was found that at least 4 wt% P in the formulation is required to show self‐extinguishing ability for both ABS and EVA when P FRs having ? CH₃ group are employed. The fire retarding efficiency of P FRs with different attached group is in order of: ? CH₃ > ? C₆H₅ > ? OH > ? H. Copyright © 2009 John Wiley & Sons, Ltd.     

Miniemulsion polymerization of styrene with a block copolymer surfactant

A series of miniemulsion systems based on styrene/azobisisobutyronitrile in the presence of poly(methyl methacrylate‐b‐2‐(dimethylamino)ethyl methacrylate) as a surfactant and hexadecane (HD) as a cosurfactant were developed. For comparison, a series of pseudoconventional emulsions also were carried out with the same procedure used for the aforementioned series but without the cosurfactant (HD). Both the droplet size and shelf life were also measured. Experimental results indicate that it is possible to slow the effect of Ostwald ripening and thereby produce a stable miniemulsion with the block copolymer as the surfactant and HD as the cosurfactant. In addition, the extent to which varying the surfactant concentration and copolymer composition could affect both the polymer particle size during the polymerization and the polymerization rate was examined. Variation in the polymer particle sizes during polymerization indicates that droplet and aqueous (micellar or both homogeneous) nucleation occurs in the miniemulsion polymerization. With the same concentration of the surfactant used in the miniemulsion polymerization, the polymerization rates of systems with M₁₂B₃₆ are faster than those of systems with M₁₂B₁₂. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1818–1827, 2000     

Surface engineering of styrene/PEGylated‐fluoroalkyl styrene block copolymer thin films

A series of diblock copolymers prepared from styrenic monomers was synthesized using atom transfer radical polymerization. One block was derived from styrene, whereas the second block was prepared from a styrene modified with an amphiphilic PEGylated‐fluoroalkyl side chain. The surface properties of the resulting polymer films were carefully characterized using dynamic contact angle, XPS, and NEXAFS measurements. The polymer morphology was investigated using atomic force microscope and GISAXS studies. The block copolymers possess surfaces dominated by the fluorinated unit in the dry state and a distinct phase separated microstructure in the thin film. The microstructure of these polymers is strongly influenced by the thin film structure in which it is investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 267–284, 2009     

Kinetics and mechanism of grafting of undecylenic acid onto acrylonitrile–butadiene–styrene terpolymer

The graft copolymerization of undecylenic acid onto acrylonitrile–butadiene–styrene terpolymer (ABS) was initiated with benzoyl peroxide (BPO) in a 1,2‐dichloroethane solution. IR spectra confirmed that undecylenic acid was successfully grafted onto the ABS backbone. The influence of the concentrations of undecylenic acid, BPO, and ABS on the graft copolymerization was studied. A reaction mechanism was proposed: the grafting most likely took place through the addition of poly(undecylenic acid) radicals to the double bond of the butadiene region of ABS. A monomer cage effect on the graft reaction was observed to depend on the 1.5 power of the monomer concentration from the experimental results of the initial rate of graft copolymerization. The initial rate of graft copolymerization was written as R_p = 1.77 × 10⁻³[P][I₂][M]^2.5/([P]+2.75[M]^2.5)². © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 486–494, 2001