New soybean oil‐styrene‐divinylbenzene thermosetting copolymers. III. Tensile stress–strain behavior

The tensile stress–strain behavior and fracture properties of some new soybean oil based polymeric materials were investigated at room temperature. These materials were prepared by the cationic copolymerization of regular soybean oil, low saturation soybean oil (LoSatSoy oil), or conjugated LoSatSoy oil with styrene and the diene comonomers divinylbenzene, norbornadiene, or dicyclopentadiene in a process initiated by boron trifluoride diethyl etherate (BF₃ · OEt₂) or related modified initiators. These new polymeric materials exhibited tensile stress–strain behavior ranging from soft rubbers through ductile to relatively brittle plastics. The Young's moduli of these polymers varied from 3 to 615 MPa, the ultimate tensile strengths varied from 0.3 to 21 MPa, and the elongation at break varied from 1.6 to 300%. These properties are obviously related to their crosslink densities. The conjugated LoSatSoy oil polymers had higher mechanical properties than the corresponding LoSatSoy oil and regular soybean oil polymers with the same stoichiometry. Some conjugated LoSatSoy oil polymers with appropriate stoichiometries showed yielding behavior in the tensile test process. A variety of new polymer materials can thus be prepared by varying the stoichiometry, the type of soybean oil, and the crosslinking agent. These soybean oil based polymers possessed mechanical properties comparable to those of commercially available rubbery materials and conventional plastics and thus may serve as replacements in many applications. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 60–77, 2001     

New soybean oil–styrene–divinylbenzene thermosetting copolymers. II. Dynamic mechanical properties

A variety of new polymeric materials ranging from soft rubbers to hard, tough, and brittle plastics were prepared from the cationic copolymerization of regular soybean oil, low saturation soybean oil (LoSatSoy oil), or conjugated LoSatSoy oil with styrene and divinylbenzene initiated by boron trifluoride diethyl etherate (BF₃ · OEt₂) or related modified initiators. The relationship between the dynamic mechanical properties of the various polymers obtained and the stoichiometry, the types of soybean oils and crosslinking agents, and the different modified initiators was investigated. The room‐temperature storage moduli ranged from 6 × 10⁶ to 2 × 10⁹ Pa, whereas the single glass‐transition temperatures (T_g) varied from approximately 0 to 105 °C. These properties were comparable to those of commercially available rubbery materials and conventional plastics. The crosslinking densities of the new polymers were largely dependent on the concentration of the crosslinking agent and the type of soybean oil employed and varied from 74 to 4 × 10⁴ mol/m³. The T_g increased and the intensity of the loss factor decreased irregularly with an increase in the logarithmic crosslinking densities of the polymers. Empirical equations were established to describe the effect of crosslinking on the loss factor in these new polymeric materials. The polymers based on conjugated LoSatSoy oil, styrene, and divinylbenzene possessed the highest room‐temperature moduli and T_g 's. These new soybean oil polymers appear promising as replacements for petroleum‐based polymeric materials. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2721–2738, 2000     

Porous structure formation and swelling properties of styrene–divinylbenzene copolymers – effect of diluent nature

The effect of the diluent solvating power on the porosity and swelling properties of styrene–divinylbenzene copolymers was investigated. A mechanism for the swelling of macroporous copolymers in good and poor solvent was proposed. The porous structures were classified according to kinetic data of a poor solvent sorption. When the diluent–copolymer affinity was reduced, the fixed pore volume increased, but the nuclei swelling and the elasticity of internuclear chains diminished.     

Fractionation of styrene–acrylonitrile copolymers

Three types of commercial styrene–acrylonitrile copolymer were fractionated by coacervate extraction and by column-elution techniques. Both methods were studied with two different solvent–nonsolvent pairs. Glass wool was used as the support material in the column. Fractionation by the coacervate extraction method was studied with benzene–triethylene glycol as a solvent–nonsolvent system at 60°C and with dichloromethane–triethylene glycol at 25°C. Column elution was carried out with acetone–methanol as the solvent–nonsolvent system at 30°C, and with dichloromethane–methanol at 20°C. Results of excellent reproducibility were obtained by these two methods. Characterization of fractions involved determination of both the molecular weight and chemical composition. It was established that the fractionation of the samples tested was dependent upon molecular weight only. The two methods described above are compared. Each gives an efficient procedure for fractionation of styrene–acrylonitrile copolymers.     

Intramolecular cyclization of styrene–p-divinylbenzene copolymers

Styrene has been copolymerized at low conversion with minor quantities of p-divinyl-benzene (p-DVB) in (10–15%) solution in toluene and cyclohexane. Under these conditions the molecular weight of the polystyrene formed in the absence of p-DVB was controlled by chain transfer, and the copolymerization coefficients of the styrene and the p-DVB agreed with previous work. Polymer molecular weights were studied as a function of conversion. At very low conversions the number-average (2.2 × 10⁵) and the weight-average (4.4 × 10⁵) molecular weights were unaffected by substituting some of the styrene by p-DVB, but as the reaction continued M?_n increased slowly and M?_w much faster. On the other hand, even at the lowest conversions the intrinsic viscosity was drastically reduced by the introduction of p-DVB, and the radius of gyration, as measured by light scattering, fell. Infrared studies on the polymer show that the concentration of pendent double bonds in low-conversion copolymers is about half of the doubly substituted phenyl groups. It is concluded that the first polymer chains formed are extensively cyclized with the formation of a relatively large number of small rings.     

Dilute solution properties of styrene–acrylonitrile and styrene–methyl methacrylate copolymers. I. Intrinsic viscosity–molecular weight relations

Styrene–acrylonitrile (St–AN) copolymers of three compositions—27.4 mole-% (SA₁); 38.5 mole-% (SA₂); and 47.5 mole-% (SA₃) acrylonitrile—and styrene–methyl methacrylate (St–MMA) copolymer (SM) of 46.5 mole-% methyl methacrylate were prepared by bulk polymerization at 60°C with benzoyl peroxide as the initiator, and were then fractionated. The molecular weights of unfractionated and fractionated samples were determined by light scattering in a number of solvents. The [η] versus M?_w relations at 30°C were established for SA₁, SA₂, SM, and polystyrene (PSt) in ethyl acetate (EAc), dimethyl formamide (DMF), and γ-butyrolactone (γ-BL), and for SA₃ in methyl ethyl ketone (MEK), DMF, and γ-BL. Second virial coefficients A₂ and the Huggins constant were determined. From values of A₂ and the exponent a of the Mark–Houwink relation it is seen that the solvent power for samples SA₁, SA₂, and PSt is in the order EAc < γ-BL < DMF, while for sample SA₃ the solvent power is in the order MEK < γ-BL < DMF. The solvent power decreases with an increase in AN content. The solvent power of the three solvents used for SM copolymer sample is practically the same within experimental errors. From the a values it is concluded that in a given solvent the copolymer chains are more extended than the corresponding homopolymers.     

Ordered structures of styrene–butadiene block copolymers

Anionically prepared block copolymers of butadiene and styrene exhibit solution properties which result from a two-dimensional ordering of the polymer molecules. The most notable of these properties is the iridescent colors of toluene solutions which are dependent on concentration and abruptly change on mechanical deformation. Electron micrographs of the surface of cast films indicate that the ordered structure is retained to some degree in the solid state.     

Influence of functional sulfonic acid groups on styrene–divinylbenzene copolymer pyrolysis

The decomposition ratio of cation exchange resin (sulfonated ST-DVB copolymer) after pyrolysis is only 50 wt%, while that of ST-DVB copolymer is 90 wt%. Fundamental experiments were performed to investigate the reason for the low decomposition ratio of the former. The cation resin consists of base polymer (ST-DVB copolymer) and functional sulfonic acid groups. Chemical analyses of the pyrolysis products showed that most of the functional groups decomposed at about 300°C and generated SO₂ gas. However, only a small amount of the base polymer was pyrolyzed even at 600°C and the total decomposition ratio was only 50 wt%. The XPS studies on the residue showed that 35% of the functional sulfonic acid groups was converted to sulfonyl and sulfur bridges between the base polymers during pyrolysis. These bridges made the base polymers, namely ST-DVB copolymer, thermally stable.     

13C-NMR spectroscopic analysis of vinyl groups in styrene–divinylbenzene networks

p-Divinylbenzene (DVB) ¹³C-labeled at the methine carbon of the vinyl group was copolymerized in suspension with styrene at 70, 70–95, and 135–155°C using 2,2′-azobisisobutyronitrile (AIBN) as the initiator. The number of unreacted vinyl groups in each copolymer was determined by ¹³C CP–MAS NMR analysis of solid samples, direct polarization ¹³C-NMR analysis of CDCl₃-swollen gels, and bromination. Results from the three methods agree methods agree qualitatively. Even the 1% DVB-crosslinked networks contained 40% unreacted DVB-vinyl groups when prepared by high conversion polymerization at 70°C and 16% unreacted DVB-vinyl groups when polymerization was finished at 95°C. The analyses were also applied to some commercial crosslinked polystyrenes. Every sample examined contained pendent vinyl groups     

Surface properties of styrene–ethylene oxide block copolymers

Hydrophobic–hydrophilic block copolymers were prepared by “living” anionic polymerization. They consist of polystyrene and poly(ethylene oxide) blocks, and are soluble in water. Their interfacial properties were investigated, employing aqueous solutions. The block copolymers lowered the surface tension of water in analogy with the low molecular weight surfactants such as sodium lauryl sulfate and heptaethylene oxide n-dodecyl ether. Their aqueous solutions exhibited solubilization properties differing from those of polyethylene glycol. Therefore, it is thought that the polystyrene blocks produce solubilization phenomena. In samples of the same styrene content, the precipitation temperature of a high molecular weight copolymer in water was lower than that of a low molecular weight copolymer at the same concentration in the same solvent. The surface tension and precipitation temperature of aqueous solutions seem to be influenced by molecular weight and composition.     

Solution behavior of styrene–ethylene oxide block copolymers

Hydrophobic–hydrophilic water-soluble block copolymers were prepared by “living” anionic polymerization. They consist of a polystyrene block and a polyethylene oxide block. From data on solution viscosity and high-resolution NMR in water, the molecular dimensions of the two-blocks copolymers are found similar to that of polyethylene glycols of the same molecular weight in the same solvent. These block copolymers exhibit microphase separation.     

Crazing in thin films of styrene–butadiene–styrene block copolymers

The mechanism of craze initiation and growth and its relationship to mechanical properties has been studied in thin films of styrene–butadiene–styrene (SBS) block copolymers. Optical microscopy and transmission electron microscopy were used to examine three copolymers which has a spherical rubber domain morphology but varied in rubber content from 20 to 50%. With increasing rubber content, the crazes became longer and less numerous. Widening of the crazes was at least partially responsible for the higher strains achieved in the copolymers, especially for the composition with the highest rubber content where the crazes widened to form micronecks. Transmission electron microscopy revealed that craze initiation and growth at the craze tip occurred by cavitation in the polystyrene phase. Cavitation of the continuous phase rather than the rubber domains was attributed to the concentration of chain-end flaws in the polystyrene. Crazes in the block copolymers followed a meandering pathway and the boundaries between crazed and uncrazed material were indistinct. Incorporation of fibrillated rubber particles into the craze fibrils strengthened the craze. At higher rubber content, the craze widened in the stress direction by voiding and fibrillation, which produced a cellular morphology.     

Structure of styrene–butadiene–styrene block copolymers by diffusion analysis

In this study, solvent sorption was used to investigate the morphology of a styrene–butadiene–styrene (SBS) triblock copolymer. The sorption process was found to deviate from the normal Fickian character, usually found in conventional elastomer–solvent systems, because of the presence of an interfacial region for both polybutadiene and polystyrene. This interphase absorbed solvent at a temperature below its glass transition and contributed to the resulting non-Fickian time-dependent diffusion process. The equilibrium diffusion coefficient was estimated to be 3.2 × 10^?7 cm²/sec regardless of the casting surface. Nevertheless, according to the sorption measurements, the casting surface did have an effect on the approach to equilibrium. The results indicated a denser packing of the molecules and hence a decreased diffusion coefficient for Teflon and glass cast films, because of internal stresses left within the films during casting.     

Macroreticular redox polymers. III. Characterization of some hydroquinone–quinone redox polymers

A series of hydroquinone–quinone redox polymers on highly and lightly crosslinked macroreticular styrene–divinylbenzene matrices was characterized for redox capacity, reactivity, equilibria, and redox potential. The effects of cerium(IV), iron(III), and oxygen on determinations of redox capacity are described.     

Dilute solution properties of styrene–acrylonitrile and styrene–methyl methacrylate copolymers. II. Short-range and long-range interactions from intrinsic viscosity data

Experimental data on styrene–acrylonitrile (St–AN), and styrene–methyl methacrylate (St–MMA) copolymers reported in Part I of this series are tested by “two-parameter” theoretical relations. The Fox–Flory (F–F) parameter K is estimated using the F–F, Stockmayer–Fixman (S–F), and Inagaki–Ptitsyn (I–P) equations. In general, the K values obtained by the F–F equation are low for the three St–AN copolymer samples in the systems studied while the values obtained from S–F and I–P equations agree within the limits of experimental error. Values of K obtained from Kurata–Stockmayer (K–S) equation for sample SA₁ agree with values obtained by the S–F and I–P equations. The specific solvent effect on the K values is discussed. Values of the unperturbed dimension r?0²/M?_w, calculated from the K values estimated from the S–F equation and from the homopolymer data are compared. Except in one case, the calculated r?0²/M?_w values from homopolymer data are low in comparison with the values obtained from experimental data, which shows that the presence of the repulsive interactions between unlike monomer units brings about an expansion of copolymer molecule. The effect of composition on the steric factor σ values is discussed. The long-range interaction parameter B, the excess interaction parameters ΔB_AB, and χAB are calculated. The effects of composition and solvent on these parameters are discussed.     

Flexibilized styrene–N‐substituted maleimide copolymers. II. Multiblock copolymers prepared from PTHF‐based iniferters

This article describes the synthesis and molecular characterization of thermal polymeric iniferters, based on hydroxy‐terminated poly(tetrahydrofuran) (PTHF), bearing thiuram disulfide groups along the chain. Thermal polymerization after the addition of styrene (S) and N‐methylmaleimide (MI) to these PTHF‐based polymeric iniferters yielded segmented PTHF (SMI‐block‐PTHF)_n block copolymers that proved to have a single T_g. The multiblock copolymers were molecularly characterized by elemental analysis, IR, and NMR. The thermal stability, as checked by thermogravimetric analysis, proved to be good up to about 350 °C. A size exclusion chromatography/differential viscosity (DV) analysis showed that the molecular weights of the synthesized single‐phase multiblock copolymers were sufficiently high (several times the estimated molecular weight between two adjacent entanglements) to determine the entanglement density from the rubbery plateau modulus, for which the method developed by S. Wu (J Polym Sci Part B: Polym Phys 1989, 27, 723–741) was applied. The entanglement density of flexibilized SMI proved to be about 20–25% higher than that of the nonflexibilized SMI. This increase is disappointing, and more work, based on the described concept, is required to achieve the desired enhancement of the toughness. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3558–3568, 2000     

Molecular structure of synthetic rubber. I. Light-scattering properties of styrene–butadiene copolymers

The discrepancy between the values reported for the weight-average molecular weight and molecular weight distribution of cold-type styrene-butadiene rubber is examined. The results obtained indicate that aggregation of the rubber due to hydrogen bonding or cluster formation is not a contributing factor to the high weight-average molecular weights obtained. The very broad molecular weight distributions, the M?_w/M?_n of the order of 10–20, are attributable to the presence of a few per cent of very high molecular weight fraction microgel in samples polymerized to moderate conversions. This microgel has been removed to various degrees by several methods: (1) mastication, (2) treatment with CaSO₄, (3) ultracentrifugation, and (4) ultrafiltration. The nature of this microgel is examined in terms of its light-scattering property, intrinsic viscosity, and concentrated solution viscosity. The weight-average molecular weight obtained by light scattering on these samples after removal of microgel are lower by as much as an order of magnitude. The operational definition of the weight-average molecular weight, M?′_w, is therefore introduced, corresponding to the one obtained after removal of the microgel. It is suggested that the actual and the operational weight-average molecular weights be used in conjunction in the characterization of these copolymers.