Vinylhydroquinone. III. Copolymerization of vinylhydroquinone and vinyl monomers by tri-n-butylborane

The copolymerization of vinylhydroquinone (VHQ) and vinyl monomers, e.g., methyl methacrylate (MMA), 4-vinyl-pyridine (4VP), acrylamide (AA), and vinyl acetate (VAc), by tri-n-butylborane (TBB) was investigated in cyclohexanone at 30°C under nitrogen. VHQ is assumed to copolymerize with MMA, 4VP, and AA by vinyl polymerization. The following monomer reactivity ratios were obtained (VHQ = M₂): for MMA/VHQ/TBB, r₁ = 0.62, r₂ = 0.17; for 4VP/VHQ/TBB, r₁ = 0.57, r₂ = 0.05; for AA/VHQ/TBB, r₁ = 0.35, r₂ = 0.08. The Q and e values of VHQ were estimated on the basis of these reactivity ratios as Q = 1.4 and e = ?;1.1, which are similar to those of styrene. This suggests that VHQ behaves like styrene rather than as an inhibitor in the TBB-initiated copolymerization. No homopolymerization was observed either under nitrogen or in the presence of oxygen. The reaction mechanism is discussed.     

Structure and reactivity of α,β-unsaturated ethers. VIII. Cationic copolymerizations and acetal additions of propenyl and isobutenyl ethyl ethers

Cationic copolymerizations of cis- and trans-propenyl ethyl ethers (PEE) with isobutenyl ethyl ether (IBEE) were carried out in methylene chloride at ?78°C with the use of boron trifluoride etherate as catalyst. Monomer reactivity ratios were r₁ = 24.0 ± 2.4 and r₂ = 0.02 ± 0.02 for the cis-PEE (M₁)–IBEE (M₂) system and r₁ = 19.1 ± 1.8 and r₂ = 0.04 ± 0.02 for the trans-PEE (M₁)–IBEE (M₂) system, indicative of the reactivity order: cis-PEE > trans-PEE ? IBEE. In separate experiments, these β-methyl-substituted vinyl ethers were allowed to react with various acetals in the presence of boron trifluoride etherate. The relative reactivities of these ethers were generally found to decrease in the order: cis-β-monomethylvinyl > vinyl > trans-β-monomethylvinyl > β,β-dimethylvinyl. Comparisons of these results with previously published copolymerization data have permitted the conclusion that, in both the copolymerizations and acetal additions, the single β-methyl substitution on vinyl ethers exerts little steric effect against their additions toward any alkoxycarbonium ion, whereas the β,β-dimethyl substitution results in a large adverse steric effect toward both β-monomethyl- and β,β-dimethyl-substituted alkoxycarbonium ions.     

Functional polymers. XII: Synthesis and polymerization of 2(2-vinyl-4-hydroxyphenyl)2H-benzotriazole and 2(3-vinyl-4-hydroxyphenyl)2H-benzotriazole

Condensation of diazotizedo-nitroaniline with 3-ethylphenol or with 2-ethylphenol followed by reduction of the resulting azo compound with zinc dust in sodium hydroxide solution gave 2-(2-ethyl-4-hydroxyphenyl)2H-benzotriazole and 2(3-ethyl-4-hydroxyphenyl)2H-benzotriazole, respectively. The individual compounds were acetylated, brominated withN-bromosuccinimide to the corresponding 1-bromoethyl compounds which were then dehydrobrominated with triethyl amine in acetonitrile and hydrolyzed to 2(2-vinyl-4-hydroxyphenyl)2H-benzotriazole or 2(3-vinyl-4-hydroxyphenyl)2H-benzotriazole. The two monomers could be polymerized and copolymerized with styrene and methyl methacrylate. The ethyl as well as the vinyl compounds and the corresponding polymers, when tested, are ineffective as ultraviolet absorbers as they have structures of 4-hydroxyphenyl rather than 2-hydroxyphenyl compounds with respect to the benzotriazole ring. A careful NMR analysis for the correct structural assignment is also described.Part XI:S. Yoshida andO. Vogl, Makromol. Chem., in press.     

Organometallic polymers. XXIV. Radical-initiated copolymerization of ferrocenylmethyl acrylate and methacrylate with acrylonitrile,maleic anhydride,and N-vinyl-2-pyrrolidone

Ferrocenylmethyl acrylate (I) and ferrocenylmethyl methacrylate (II) have been readily copolymerized with maleic anhydride in benzene–ethyl acetate solutions. Similarly, II has been copolymerized with both acrylonitrile and N-vinyl-2-pyrrolidone in benzene solutions to give higher molecular weight copolymers in high yields. In all cases azobisisobutyronitrile has been the initiator. Based on e values obtained, the metal carbonyl substituent acts as an electron-withdrawing group. Over a wide range of comonomers (N-vinyl-2-pyrrolidone, styrene, vinyl acetate, methyl acrylate, acrylonitrile, and maleic anhydride) I and II exhibit r₁ values lower than (and r₂ values higher than) similar copolymerizations with methyl acrylate or methyl methacrylate. Further more, the Q values found for I (0.03–0.11) and II (0.08–0.18) are smaller than those for methyl acrylate (0.46) and methyl methacrylate (0.74). Thus, I and II are less reactive than expected, presumably due to steric effects.     

Sulfur-Containing Vinyl Monomers. XIV. Radical Polymerizations and Copolymerizations of Vinyl Mercaptobenzazoles

Vinyl mercaptobenzazoles [thiazole (VMBT), oxazole (VMBO), and imidazole (VMBI)] were prepared through dehydrochlorination of the respective β-chloroethyl mercaptobenzazoles. These monomers were found to undergo vinyl polymerization in the presence of light or radical initiator, α,α'-azobisisobutyonitrile, to give relatively high molecular weight homopolymers. From the results of radical copolymerizations of these monomers with various monomers, the copolymerization parameters were determined as follows: VMBT(M₂): r₁ styrene(M₁): r₁ = 2.12 ± 0.09, r₂ = 0.336 ± 0.028, Q₂ = 0.75, e_z = ?1.38; VMBO(M₂)-styrene(M₁): r₁ = 2.61 ± 0.13, r₂ = 0.274 ± 0.03, Q₂ = 0.61, e₂ = ?1.38; VBMI(M₂)-styrene(M₁) r₁ =4.0, r₂ = 0.2, Q₂ = 0.37, e₂ = ?1.17. The polymerization reactivities of these monomers obtained from these parameters were compared with those of other vinyl sulfide monomers and discussed.     

Determination of the reactivity ratios of methyl acrylate with the vinyl acetate,vinyl 2,2-dimethyl-propanoate,and vinyl 2-ethylhexanoate

The course of composition drift in copolymerization reactions is determined by reactivity ratios of the contributing monomers. Since polymer properties are directly correlated with the resulting chemical composition distribution, reactivity ratios are of paramount importance. Furthermore, obtaining correct reactivity ratios is a prerequisite for good model predictions. For vinyl acetate (VAc), vinyl 2,2-dimethyl-propanoate also known as vinyl pivalate (VPV), and vinyl 2-ethylhexanoate (V2EH), the reactivity ratios with methyl acrylate (MA) have been determined by means of low conversion bulk polymerization. The mol fraction of MA in the resulting copolymer was determined by ¹H-NMR. Nonlinear optimization on the thus-obtained monomer feed–copolymer composition data resulted in the following sets of reactivity ratios: r_MA = 6.9 ± 1.4 and r_VAc = 0.013 ± 0.02; r_MA = 5.5 ± 1.2 and r_VPV = 0.017 ± 0.035; r_MA = 6.9 ± 2.7 and r_V2EH = 0.093 ± 0.23. As a result of the similar and overlapping reactivity data of the three methyl acrylate–vinyl ester monomer systems, for practical puposes these data can be described with one set of reactivity data. Nonlinear optimization of all monomer feed–copolymer composition data together resulted in r_MA = 6.1 ± 0.6 and r_VEst = 0.0087 ± 0.023. © 1994 John Wiley & Sons, Inc.     

Radical copolymerization of novel trifluorovinyl ethers with ethyl vinyl ether and vinyl acetate: Estimating reactivity ratios and understanding reactivity behavior of the propagating radical

Two novel trifluorovinyl ether (TFVE) monomers were copolymerized with either ethyl vinyl ether (EVE) or vinyl acetate (VAc) in a redox‐initiated aqueous emulsion: 1‐(2‐phenoxyethoxy)‐1,2,2‐trifluoroethene (Ph‐TFVE) and 1‐[2‐(2‐ethoxyethoxy)ethoxy]‐1,2,2‐trifluoroethene (Et‐TFVE). Previous studies demonstrated a propensity for radical hydrogen abstraction from the oligoether pendant group during the homopolymerization of Et‐TFVE with continued propagation of the resulting radical, thereby providing the rationale to investigate the copolymerization of our new TFVEs with EVE or VAc. Reactivity ratios were estimated using the error‐in‐variables model from a series of bulk free radical copolymerizations of Ph‐TFVE with EVE or VAc. The reactivity ratios were r_Ph‐TFVE = 0.25 ± 0.07, r_EVE = 0.016 ± 0.04; r_Ph‐TFVE = 0.034 ± 0.04, r_VAc =0.89 ±0.08. Partial hydrolysis of polymers containing VAc to vinyl alcohol (VA) resulted in two terpolymers: poly(Ph‐TFVE‐co‐VAc‐co‐VA) and poly(Et‐TFVE‐co‐VAc‐co‐VA), respectively. We investigated the possibility of hydrogen abstraction from VAc during polymerization by comparing the molar mass before and after hydrolysis. Abstraction from VAc was not apparent during polymerization; however, abstraction from the oligoether pendant group of Et‐TFVE was again evident and was more significant for those copolymers having a greater fraction of Et‐TFVE in the monomer feed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1344–1354, 2000     

FURTHER STUDY OF ALLYL ETHERS AND RELATED COMPOUNDS AS TRANSFER AGENTS IN RADICAL POLYMERIZATIONS

Allyl glycidyl ether (AGE), allyl 1,1,2,3,3,3-hexafluoropropyl ether (AFE), allyl 2-naphthyl ether (ANE), 2-vinyl-1,3-dioxolane (2VD) and allyl alcohol (AA) have been examined as transfer agents in the radical polymerization of methyl methacrylate (MMA) at 60°C; the transfer constants are 1.1 × 10^?3, 0.1 × 10^?3, 0.2 × 10^?3, 1.1 × 10^?3 and 0.6 × 10^?3, respectively. AFE and AA barely affect the rate of polymerization: AGE, ANE, and 2VD act as weak retarders. There is no direct correlation between effectiveness as a transfer agent and the extent of retardation for these additives. For copolymerization with MMA (monomer-1), the monomer reactivity ratios r₁ are 42 ± 5 and 32 ± 5 for AGE and ANE, respectively; for both cases, r₂ is very close to zero; 2VD engages in copolymerization with MMA to a negligible extent. Experiments involving styrene or acrylonitrile gave results consistent with those obtained using MMA.     

Silyl enol ethers as monomer. III. Radical polymerization and copolymerizations of 2-trimethylsilyloxy-1,3-butadiene and desilylation of the resulting polymers

2-Trimethylsilyloxy-1,3-butadiene (TMSBD), the silyl enol ether of methyl vinyl ketone, was homopolymerized with a radical initiator to afford polymers with a molecular weight of ca. 10⁴. Radical copolymerizations of TMSBD with styrene (ST) and acrylonitrile (AN) in bulk or dioxane at 60°C gave the following monomer reactivity ratios: r₁ = 0.64 and r₂ = 1.20 for the ST (M₁)–TMSBD (M₂) system and r₁ = 0.036 and r₂ = 0.065 for the AN (M₁)–TMSBD (M₂) system. The Q and e values of TMSBD determined from the reactivity ratios for the former copolymerization system were 2.34 and ?1.31, respectively. The resulting polymer and copolymers were readily desilylated with hydrochloric acid or tetrabutylammonium fluoride as catalyst to yield analogous polymers having carbonyl groups in the polymer chains.     

Photopolymerization with the use of titanocene dichoride as sensitizer

Titanocene dichloride sensitized photopolymerization of vinyl ethers and styrene but did not polymerize methyl methacrylate and vinyl acetate. In the case of 2-chloroethyl vinyl ether, polymerization started rapidly some time after the color of the liquid had changed from orange to green. Polymerization was also achieved by heating the monomer at 60°C after stopping the irradiation at the end of the induction period. On the basis of the reactivity of the monomers and the effect of additives, polymerization is considered to proceed cationically. In case of the polymerization of styrene, conversion increased linearly with time. The k/k_t value of 6.3 × 10^?5l./mole-sec obtained for the polymerization of styrene agrees well with the value reported for radical polymerization. The agreement of the value and ineffective inhibition of polymerization in the presence of pyridine indicates the polymerization follows a radical mechanism. Copolymerization of styrene (M₁) and 2-chloroethyl vinyl ether (M₂) proceeded radically, and the reactivity ratios were r₁ = 2.5 and r₂ = 0.6.     

Structure and reactivity in cationic polymerization of butadiene derivatives. IV. 1-alkoxybutadienes

The reactivity of trans-1-alkoxybutadienes in cationic homopolymerization and copolymerizations and structure of the polymers produced were investigated. 1-Ethoxybutadiene is polymerized easily at ?78°C by various acidic catalysis. The reactivity of 1-ethoxybutadiene was similar to that of ethyl vinyl ether. The polymers produced possessed molecular weights of several thousands, and were composed of 70–95% 1,4 structure and 5–30% 3,4 structure. In the copolymerization of ethyl vinyl ether (M₁) with 1-ethoxybutadiene at ?78°C in toluene by boron trifluoride diethyl etherate, r₁ = 1.15, r₂ = 2.62. From the Hammett plot of the relative reactivities of alkoxybutadienes (alkoxy: CH₃O, C₂H₅O, i-C₃H₇O), the reaction constant _p^* was determined to be ?2.9. Results of the present study were compared with those of various butadiene derivatives.     

Aminimides. IV. Homo- and copolymerization studies on trimethylamine methacrylimide

Trimethylamine methacrylimide (TAMI) has been homo- and copolymerized with methyl methacrylate, vinyl acetate, vinyl chloride, hydroxypropyl methacrylate, and acrylonitrile by free-radical initiators to soluble, low molecular weight polymers containing pendant aminimide groups along the backbone of the polymer chains. The reactivity ratios in the copolymerization of TAMI (M₁) with acrylonitrile (M₂) were determined: r₁ = 0.10 ± 0.01, r₂ = 0.37 ± 0.04. The Alfrey-Price Q and e values for TAMI were also calculated: Q = 0.18, e = ?0.60. This preliminary work indicates that TAMI has potential for the preparation of reactive polymers.     

Self-crosslinkable polymers. I. Copolymerization of glycidyl methacrylate with 2-vinylpyridine and 2-vinyl-5-ethylpyridine

A soluble and self-crosslinkable linear copolymer with pendant epoxy and pyridyl groups was obtained from glycidyl methacrylate (M₁) and 2-vinylpyridine (M₂) or 2-vinyl-5-ethylpyridine (M₂) by the action of azobisisobutyronitrile. The monomer reactivity ratios were determined in tetrahydrofuran at 60°C: r₁ = 0.510, r₂ = 0.620 with 2-vinylpyridine and r₁ = 0.57, r₂ = 0.62 with 2-vinyl-5-ethylpyridine. These were consistent with the calculated values with the reported Q and e values for these monomers. The intrinsic viscosities of the copolymers with 2-vinylpyridine and with 2-vinyl-5-ethylpyridine were found to be 0.17–0.19 and 0.26–0.38, respectively, in tetrahydrofuran at 30°C; they were independent of the copolymer composition. The copolymers were amorphous, had no clear melting points, and became insoluble crosslinked polymers under heating without further addition of any curing agents.     

Reactivities and NMR spectra of vinyl ethers

Copolymerizations of n-butyl vinyl ether (M₁) with other vinyl ethers were carried out in toluene at ?78°C with EtAlCl₂ catalyst and the monomer reactivity ratios were determined. It was found that the relative reactivity of alkyl vinyl ether log 1/r₁ is higher when the alkyl group is more electron-donating and the reactivity correlates linearly with the Taft σ^* of alkyl group in the monomer. The NMR spectra of vinyl ethers and of vinyl ether–trialkylaluminum complexes were investigated. Close correlations were found between the spectral characteristics and the relative reactivity of vinyl ether in the copolymerization. The degree of resonance contribution in alkyl vinyl ether was also discussed on the basis of NMR data.     

A Comparative Study of (Poly)ether Adducts of Alkaline Earth Iodides – An Overview Including New Compounds

New homoligand and mixed‐ligand adducts of the heavier alkaline earth metal (Ca, Sr, Ba) halides with oxygen‐donor polyether ligands have been isolated and characterized and are compared with previously obtained compounds of the same class in order to give an overview on structures and properties. Homoligand halide adducts, discussed herein, are [CaI(DME)₃]I ( 1 ), trans‐[SrI₂(DME)₃] ( 2 ), trans‐[BaI₂(DME)₃] ( 3 ), (DME = ethylene glycol dimethyl ether), [CaI(diglyme)₂]I ( 4 ), cis‐[SrI₂(diglyme)₂] ( 5 ), trans‐[BaI₂(diglyme)₂] ( 6 ),(diglyme = diethylene glycol dimethyl ether, [SrI(triglyme)₂]I ( 7 ), and [BaI(triglyme)₂]I ( 8 ), (triglyme = triethylene glycol dimethyl ether). Introduction of the mono‐coordinating THF ligand (THF = tetrahydrofuran) in the coordination sphere of 1 , 2 , 3 , 4 allows the formation of the new mixed‐ligand compounds trans‐[CaI₂(DME)₂(THF)] ( 9 ), trans‐[SrI₂(DME)₂(THF)] ( 10 ), trans‐[BaI₂(DME)₂(THF)₂] ( 11 ), and trans‐[CaI₂(diglyme)₂(THF)₂] ( 12 ). These compounds were obtained from the metal halide salts in solution with pure or mixtures of ether solvents. While compounds 1 – 8 appear to be very stable and non‐reactive, adducts 9 – 12 present a comparable reactivity to the well known THF adducts [MI₂(thf)_n] (M = Ca, n = 4; Sr, Ba, n = 5).     

Epoxy Type Inhibitors of Cholesterol Esterase,Acetylcholinesterase, and Butyrylcholinesterase

Epoxy type inhibitors, 3‐t‐butylphenyl 3‐1,2‐epoxybutyl ether ( 1 ), 3‐t‐butylphenyl 3‐1,2‐epoxyhexyl ether ( 2 ), and 2‐naphthyl 3‐1,2‐epoxyhexyl ether ( 3 ) are synthesized as the active site‐directed inhibitors of cholesterol esterase, acetylcholinesterase, and butyrylcholinesterase. All epoxy compounds are characterized as the time‐independent inhibitors for all three enzymes from the stopped‐time assay. Further, all epoxy compounds are characterized as the competitive inhibitors for all three enzymes from the Lineweaver‐Burk plots. The inhibition constants (K_i) of cholesterol esterase for compounds 1‐3 are 320 ± 40, 190 ± 20, 130 ± 20 μM, respectively. The K_i values of acetylcholinesterase for compounds 1‐3 are 490 ± 20, 141 ± 5, 200 ± 30 μM, respectively. Values of K_i of butyrylcholinesterase for compounds 1‐3 are 250 ± 30, 26 ± 4, 120 ± 20 μM, respectively. Compound 2 is the most potent inhibitor for butyrylcholinesterase probably because the compound mimics most the natural substrate, butyrylcholine.     

Geometry and bond‐length alternation in nonlinear optical materials. II. Effects of donor strength in two push–pull molecules

The compounds N‐[2‐(4‐cyano‐5‐dicyanomethylene‐2,2‐dimethyl‐2,5‐dihydrofuran‐3‐yl)vinyl]‐N‐phenylacetamide, C₂₀H₁₆N₄O₂,(I), and 2‐{3‐cyano‐5,5‐dimethyl‐4‐[2‐(piperidin‐1‐yl)vinyl]‐2,5‐dihydrofuran‐2‐ylidene}malononitrile 0.376‐hydrate, C₁₇H₁₈N₄O·0.376H₂O, (II), are novel push–pull molecules. The significant bonding changes in the polyene chain compared with the parent molecule 2‐dicyanomethylene‐4,5,5‐trimethyl‐2,5‐dihyrofuran‐3‐carbonitrile are consistent with the relative electron‐donating properties of the acetanilido and piperidine groups. The packing of (I) utilizes one phenyl–cyano C—H...N and two phenyl–carbonyl C—H...O hydrogen bonds. Compound (II) crystallizes with a partial water molecule (0.376H₂O), consistent with cell packing that is dominated by attractive C—H...N(cyano) interactions. These compounds are precursors to novel nonlinear optical chromophores, studied to assess the impact of donor strength and the extent of conjugation on bond‐length alternation, crystal packing and aggregation.     

Vinylhydroquinone. IV. Preparation and polymerization behavior of 2-methyl-5-vinylhydroquinone derivatives

As in the case of vinylhydroquinone (I), its alkyl-substituted derivative, 2-methyl-5-vinylhydroquinone (II) was found to copolymerize with methyl methacrylate by tri-n-butylborane in cyclohexanone at 30°C. II was prepared from the O,O′-bisether compound, 2-methyl-5-vinyl-O,O′-bis(1′-ethoxyethyl)hydroquinone (III). The monomer reactivity ratios (M₂ = II) were determined to be r₁ = 0.37 and r₂ = 0. No homopolymerization proceeded under the same conditions. Ordinary free-radical initiators, such as azobisisobutyronitrile and benzoyl peroxide, were not effective in the homopolymerization of II. 1:1 Copolymers were obtained from II and maleic anhydride by using tri-n-butylborane as an initiator. The copolymers exhibited no definite melting range and decomposed at 370–375°C endothermally (DSC). The polymerization behavior of III was also investigated. Although tri-n-butylborane did not initiate the homopolymerization of the monomer, azobisisobutyronitrile was capable of initiating the homopolymerization and copolymerization of III. The monomer reactivity ratios (M₁ = styrene) were determined to be r₁ = 0.83 and r₂ = 0.18. The ratios gave the following Q and e values; Q = 0.15 and e = ?2.2.     

Compounds of palladium halides with substituted imidazoles

Summary Compounds of the type PdL₂X₂ (L=1-methylimidazole, 1-vinylimidazole, 1-n-butylimidazole, 1,2-dimethylimidazole, 1-vinyl-2-methylimidazole, 1,2-dimethyl-5-nitroimidazole, 2-isopropyl-4(5)-nitroimidazole and 2-methyl-4(5)-nitro-imidazole; X=Cl or Br) are obtained by treating PdX₂ (1 mole) with solutions of the ligands L (2 moles). An excess of L gives PdL₄X₂ complexes (L=1-methylimidazole, 1-vinylimidazole, 1,2-dimethylimidazole and 1-vinyl-2-methylimidazole). The compounds were characterized by chemical analyses, molar conductivity measurements and i.r. spectra.     

Copolymerization of glycidyl methacrylate with alkyl acrylate monomers

A newer approach to obtaining acrylic thermoset polymers with adequate hydrophilicity required for various specific end uses is reported. Glycidyl methacrylate (GMA) was copolymerized with n-butyl acrylate (n-BA), isobutyl acrylate (i-BA), and 2-ethylhexyl acrylate (2-EHA) in bulk at 60°C. with benzoyl peroxide as free radical initiator. The copolymer composition was determined from the estimation of epoxy group. Reactivity ratios were calculated by the Yezrielev, Brokhina, and Roskin method. For copolymerization of GMA (M₁) with n-BA (M₂) the reactivity ratios were r₁ = 2.15 ± 0.14, r₂ = 0.12 ± 0.03; with i-BA (M₂) they were r₁ = 1.27 ± 0.06, r₂ = 0.33 ± 0.031; and with 2-EHA (M₂) they were r₁ = 2.32 ± 0.14, r₂ = 0.13 ± 0.009. The reactivity ratios were the measure of distribution of monomer units in a copolymer chain; the values obtained are compared and discussed.