Structural analysis of the c(4 × 2) reconstruction in Si(0 0 1) and Ge(0 0 1) surfaces by low-energy electron diffraction

The c(4 × 2) structures in (0 0 1) surfaces of Si and Ge have been studied by low-energy electron diffraction (LEED). Using a proper cleaning method for the Si surface, we were able to observe clear c(4 × 2) LEED patterns up to incident energy of ∼400 eV as well as the Ge surface. Extensive experimental intensity-voltage curves allowed us to optimize the asymmetric dimer model up to the eighth layer (including the dimer layer) in depth in the dynamical LEED calculation. Optimized structural parameters are almost the same for the Si and Ge except for the height of the buckled-up atom of the asymmetric dimer. For the Ge surface, the structural parameters are in excellent agreement with those obtained by a previous theoretical calculation. The tilt angle and bond length of the dimer are 18 ± 1 (19 ± 1)° and 2.4 ± 0.1 (2.5 ± 0.1) Å for the Si(0 0 1) (Ge(0 0 1)), respectively.     

Ga-induced superstructures on the Si(1 1 1) 7 × 7 surface

Monolayer Ga adsorption on Si surfaces has been studied with the aim of forming p-delta doped nanostructures. Ga surface phases on Si can be nitrided by N₂⁺ ion bombardment to form GaN nanostructures with exotic electron confinement properties for novel optoelectronic devices. In this study, we report the adsorption of Ga in the submonolayer regime on 7 × 7 reconstructed Si(1 1 1) surface at room temperature, under controlled ultrahigh vacuum conditions. We use in-situ Auger electron spectroscopy, electron energy loss spectroscopy and low energy electron diffraction to monitor the growth and determine the properties. We observe that Ga grows in the Stranski-Krastanov growth mode, where islands begin to form on two flat monolayers. The variation in the dangling bond density is observed during the interface evolution by monitoring the Si (LVV) line shape. The Ga adsorbed system is subjected to thermal annealing and the residual thermal desorption studied. The difference in the adsorption kinetics and desorption dynamics on the surface morphology is explained in terms of strain relaxation routes and bonding configurations. Due to the presence of an energetic hierarchy of residence sites of adatoms, site we also plot a 2D phase diagram consisting of several surface phases. Our EELS results show that the electronic properties of the surface phases are unique to their respective structural arrangement.     

Density functional theory study of selenium adsorption on Fe(1 1 0)

The adsorption of atomic Se on a Fe(1 1 0) surface is examined using the density functional theory (DFT). Selenium is adsorbed in high-symmetry adsorption sites: the -short and long-bridge, and atop sites at 1/2, 1/4, and 1 monolayer (ML) coverages. The long bridge (LB) site is found to be the most stable, followed by the short bridge (SB) and top sites (T). The following overlayer structures were examined, p(2 × 2), c(2 × 2), and p(1 × 1), which correspond to 1/4 ML, 1/2 ML, and 1 ML respectively. Adsorption energy is −5.23 eV at 1/4 ML. Se adsorption results in surface reconstruction, being more extensive for adsorption in the long bridge site at 1/2 ML, with vertical displacements between +8.63 and −6.69% -with regard to the original Fe position-, affecting the 1st and 2nd neighbours. The largest displacement in x or y-directions was determined to be 0.011, 0.030, and 0.021 Å for atop and bridge sites. Comparisons between Se-adsorbed and pure Fe surfaces revealed reductions in the magnetic moments of surface-layer Fe atoms in the vicinity of the Se. At the long bridge site, the presence of Se causes a decrease in the surface Fe d-orbital density of states between 4 and 5 eV below Fermi level. The density of states present a contribution of Se states at −3.1 eV and −12.9 eV. stabilized after adsorption. The Fe-Fe overlap population decrease and a Fe-Se bond are formed at the expense of the metallic bond.     

Atomic surface structure of Si(1 0 0) substrates prepared in a chemical vapor environment

Subsequent III-V integration by metal-organic vapor phase epitaxy (MOVPE) or chemical vapor deposition (CVD) necessitates elaborate preparation of Si(1 0 0) substrates in chemical vapor environments characterized by the presence of hydrogen used as process gas and of various precursor molecules. The atomic structure of Si(1 0 0) surfaces prepared in a MOVPE reactor was investigated by low energy electron diffraction (LEED) and scanning tunnelling microscopy (STM) available through a dedicated, contamination-free sample transfer to ultra high vacuum (UHV). Since the substrate misorientation has a fundamental impact on the atomic surface structure, we selected a representative set consisting of Si(1 0 0) with 0.1°, 2° and 6° off-cut in [0 1 1] direction for our study. Similar to standard UHV preparation, the LEED and STM results of the CVD-prepared Si(1 0 0) surfaces indicated two-domain (2 × 1)/(1 × 2) reconstructions for lower misorientations implying a predominance of single-layer steps undesirable for subsequent III-V layers. However, double-layer steps developed on 6° misoriented Si(1 0 0) substrates, but STM also showed odd-numbered step heights and LEED confirmed the presence of minority surface reconstruction domains. Strongly depending on misorientation, the STM images revealed complex step structures correlated to the relative dimer orientation on the terraces.     

Layer-resolved photoelectron diffraction from Si(0 0 1) and GaAs(0 0 1)

Photoelectron diffraction in the layer-resolved mode brings more detailed information about local atomic arrangement than is obtained in the standard mode. This is demonstrated in crystals with diamond and zinc-blende structures, both for unpolarized photon excitation as well as for circularly polarized excitation. The full angular distributions of photoemission intensities are evaluated for large atomic clusters representing ideally truncated surfaces of Si(0 0 1) and GaAs(0 0 1). Highly structured layer-resolved patterns enable a more detailed understanding of the standard mode outcomes. Photoelectron intensities from atomic layers placed at different depths under the crystal surface provide direct evidence about electron attenuation and its anisotropy in crystals.     

Scanning tunneling microscopy luminescence from nanoscale surface of GaAs(1 1 0)

Scanning tunneling microscopy luminescence (STML) was induced from the nanometer scale surfaces of cleaved n-type and p-type GaAs(1 1 0) wafers by using of an ITO-coated optical fiber probe in an ultrahigh-vacuum chamber. The STML from n-type GaAs(1 1 0) surface was induced under negative sample bias when the applied bias exceeds a threshold voltage around −1.5 V. Whereas the STML from p-type GaAs(1 1 0) surface was induced under positive sample bias when the applied bias exceeds a threshold voltage around +1.5 V. The excitation energies at the threshold voltages are consistent with the band gap of GaAs (1.42 eV) at 295 K. The typical quantum efficiencies for n-type and p-type GaAs are about 3 × 10⁻⁵ and 2 × 10⁻⁴ photons/electron, respectively. The observed STML from are attributed to a radiative recombination of electron-hole pairs generated by a hole injection for n-type GaAs under negative sample bias and an electron injection for p-type GaAs under positive sample bias, respectively.     

Sulphur overlayers on the Au(1 1 0) surface: LEED and TPD study

The adsorption and desorption of sulphur on the clean reconstructed Au(1 1 0)-(1 × 2) surface has been studied by low energy electron diffraction, Auger electron spectroscopy and temperature programmed desorption. The results obtained show a complex behaviour of the S/Au(1 1 0) system during sulphur desorption at different temperatures. Two structures of the stable ordered sulphur overlayer on the Au(1 1 0) surface, p(4 × 2) and c(4 × 4), were found after annealing the S/Au(1 1 0) system at 630 K and 463 K, respectively. The corresponding sulphur coverage for these overlayers was estimated by AES signal intensity analysis of the Au NOO and S LMM Auger lines to be equal to 0.13 ML and 0.2 ML, respectively. Both sulphur structures appear after removing an excess of sulphur, which mainly desorbs at 358 K as determined from TPD spectra. Furthermore, it was not possible to produce the lower coverage p(4 × 2) sulphur structure by annealing the c(4 × 4) surface. In the case of the p(4 × 2) S overlayer on the Au(1 1 0)-(1 × 2) surface it is proposed that the sulphur is attached to “missing row” sites only. The c(4 × 4) S overlayer arises via desorption of S₂ molecules that are formed on the surface due to mobility of sulphur atoms after a prolonged anneal.     

Atomic and electronic structure of methanol on Ge(1 0 0)

We have performed density-functional theory (DFT) calculations to investigate the adsorption structures of methanol on a Ge(1 0 0) surface. Among many possible adsorption configurations, the most favorable configurations at room temperature were found to be those in which the OH-dissociated methanol molecule forms O-Ge bonds, with the methoxy group either parallel or perpendicular to the Ge surface. The spatial arrangement of methoxy group relative to the Ge(1 0 0) surface is not critical. The dissociated H is bonded to an adjacent up-Ge atom, passivating the dangling bond. The possibility of H diffusion to other Ge atoms is also investigated. The corresponding simulated images explain well the adsorption features observed experimentally. The reaction pathways explain the feasibility of OH-dissociative structures at room temperature. The two OH-dissociative configurations where methoxy groups are either parallel or perpendicular to Ge surfaces are similar in thermodynamic and kinetic aspects.     

Spin-polarized scanning tunneling microscopy through an adsorbate layer: Sulfur-covered Fe/W(1 1 0)

Spin-polarized scanning tunneling microscopy and spectroscopy (SP-STM/STS) has been performed on clean and sulfur-covered three-dimensional Fe islands on W(1 1 0). Upon dosing with H₂S the island surface is covered with 1/3 ML S leading to a c(3 × 1) reconstruction. The characteristic magnetic vortex structure is observable before and after dosing, even though the electronic structure of the surface is modified as is shown by SP-STS.     

Water monolayer and multilayer adsorption on Ni(1 1 1)

Water adsorbed on Ni(1 1 1) forms an ordered, hydrogen bonded ice structure with a (2√7 × 2√7)R19° unit cell. The 2√7 wetting structure forms as islands and persists up to saturation of the first layer. Adsorption of a fraction of a monolayer more water into a second layer destroys the 2√7 registry and creates a disordered ice film. Gas adsorption measurements indicate that the wetting layer is completely covered by a second layer of water before thicker multilayer ice forms. As the second layer is completed the film orders to form an incommensurate crystalline ice film with a hexagonal LEED pattern, oriented to the Ni close packed rows. This ordered, incommensurate structure persists as the ice multilayer grows thicker.     

Kinetic Monte Carlo simulations of Pd deposition and island growth on MgO(1 0 0)

The deposition and ripening of Pd atoms on the MgO(1 0 0) surface are modeled using kinetic Monte Carlo simulations. The density of Pd islands is obtained by simulating the deposition of 0.1 ML in 3 min. Two sets of kinetic parameters are tested and compared with experiment over a 200-800 K temperature range. One model is based upon parameters obtained by fitting rate equations to experimental data and assuming the Pd monomer is the only diffusing species. The other is based upon transition rates obtained from density functional theory calculations which show that small Pd clusters are also mobile. In both models, oxygen vacancy defects on the MgO surface provide strong traps for Pd monomers and serve as nucleation sites for islands. Kinetic Monte Carlo simulations show that both models reproduce the experimentally observed island density versus temperature, despite large differences in the energetics and different diffusion mechanisms. The low temperature Pd island formation at defects is attributed to fast monomer diffusion to defects in the rate-equation-based model, whereas in the DFT-based model, small clusters form already on terraces and diffuse to defects. In the DFT-based model, the strong dimer and trimer binding energies at charged oxygen vacancy defects prevent island ripening below the experimentally observed onset temperature of 600 K.     

Perturbation of Ge(1 1 1) and Si(1 1 1)√3α-Sn surfaces by adsorption of dopants

We test the response of the √3 × √3α reconstructions formed by 1/3 monolayer of tin adatoms on silicon and germanium (1 1 1) surfaces upon doping with electrons or holes, using potassium or iodine as probes/perturbers of the initial electronic structures. From detailed synchrotron radiation photoelectron spectroscopy studies we show that doping with either electrons or holes plays a complimentary role on the Si and Ge surfaces and, especially, leads to complete conversion of the Sn 4d two-component spectra into single line shapes. We find that the low binding energy component of the Sn core level for both Si and Ge surfaces corresponds to Sn adatoms with higher electronic charge, than the Sn adatoms that contribute to the core level high binding energy signal. This could be analyzed as Sn adatoms with different valence state.     

Growth kinetics of metastable (3 3 1) nanofacet on Au and Pt(1 1 0) surfaces

A theoretical epitaxial growth model with realistic barriers for surface diffusion is investigated by means of kinetic Monte Carlo simulations to study the growth modes of metastable (3 3 1) nanofacets on Au and Pt(1 1 0) surfaces. The results show that under experimental atomic fluxes, the (3 3 1) nanofacets grow by 2D nucleation at low temperature in the submonolayer regime. A metastable growth phase diagram that can be useful to experimentalists is presented and looks similar to the one found for the stationary growth of the bcc(0 0 1) surface in the kinetic 6-vertex model.     

Adsorption and reactivity of SO2 on Ir(1 1 1) and Rh(1 1 1)

The adsorption and reactivity of SO₂ on the Ir(1 1 1) and Rh(1 1 1) surfaces were studied by surface science techniques. X-ray photoelectron spectroscopy measurements showed that SO₂ was molecularly adsorbed on both the Ir(1 1 1) surface and the Rh(1 1 1) surface at 200 K. Adsorbed SO₂ on the Ir(1 1 1) surface disproportionated to atomic sulfur and SO₃ at 300 K, whereas adsorbed SO₂ on the Rh(1 1 1) surface dissociated to atomic sulfur and oxygen above 250 K. Only atomic sulfur was present on both surfaces above 500 K, but the formation process and structure of the adsorbed atomic sulfur on Ir(1 1 1) were different from those on Rh(1 1 1). On Ir(1 1 1), atomic sulfur reacted with surface oxygen and was completely removed from the surface, whereas on Rh(1 1 1), sulfur did not react with oxygen.     

Olefin bonding mechanism and growth to (1 0 0)(2 × 1):H diamond

The bonding and growth mechanism of photochemically attached olefin molecules to (1 0 0)(2 × 1):H diamond is characterized using atomic force (AFM) and scanning tunneling microscopy (STM) experiments in combination with molecular orbital calculations. To identify growth schemas, diamond surfaces after 10, 40 and 90 min of photo-chemically stimulated growth have been characterized. These data show clearly island formation which is discussed taking into account a growth model from silicon. The island growth shows no directional properties which are attributed to arrangement and geometrical properties of hydrogen terminated carbon bonds at the surface of (1 0 0) oriented (2 × 1) reconstructed diamond.     

Angle-resolved photoemission spectroscopy study of Fe(1 1 0) single crystal: Many-body interactions between quasi-particles at the Fermi level

A high-resolution angle-resolved photoemission spectroscopy (ARPES) study of Fe(1 1 0) single crystal was conducted to elucidate many-body interactions between quasi-particles at the Fermi level at low-temperature. Two kink structures were observed in the energy-band dispersion at the binding energies of ∼40 meV and ∼270 meV for the bulk-derived band on the majority-spin Fermi surface around the Γ point. Based on analyses of the experimentally obtained real parts of the self-energy, these kink structures are derived from electron-phonon and electron-magnon interactions.     

STM image visualization of Si(1 1 1) 7 × 7 surface (graphic simulation and implementation)

The possibilities of graphic STM image simulation of a clean Si(1 1 1) 7 × 7 surface at atomic level are indicated. The presented procedure takes into account various types of deformation on the surface near the Fermi level in order to classify them and explain their origin. It also gives a clear hint to insert relevant physical phenomena in a suggested analysis. This goal is achieved exploiting the results of DAS (dimmer adatom stacing fault) model by means of standard mathematical programmes. A clean Si(1 1 1) 7 × 7 surface is considered as the representative example, but similar evaluation is possible for another non-metal and metal surfaces.     

A density functional theory study of ethylene adsorption on Ni10(1 1 1), Ni13(1 0 0) and Ni10(1 1 0) surface cluster models and Ni13 nanocluster

Ethylene adsorption was studied by use of DFT/B3LYP with basis set 6-31G(d,p) in Gaussian’03 software. It was found that ethylene has adsorbed molecularly on all clusters with π adsorption mode. Relative energy values were calculated to be −50.86 kcal/mol, −20.48 kcal/mol, −32.44 kcal/mol and −39.27 kcal/mol for Ni₁₃ nanocluster, Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) surface cluster models, respectively. Ethylene adsorption energy is inversely proportional to Ni coordination number when Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) cluster models and Ni₁₃ nanocluster are compared with each other.     

Effects of electronic confinement and substrate on the low-temperature growth of Pb islands on Si(1 0 0)-2 × 1 surfaces

The growth of Pb films on the Si(1 0 0)-2 × 1 surface has been investigated at low temperature using scanning tunneling microscopy. Although the orientation of the substrate is (1 0 0), flat-top Pb islands with (1 1 1) surface can be observed. The island thickness is confined within four to nine atomic layers at low coverage. Among these islands, those with a thickness of six layers are most abundant. Quantum-well states in Pb(1 1 1) islands of different thickness are acquired by scanning tunneling spectroscopy. They are found to be identical to those taken on the Pb(1 1 1) islands grown on the Si(1 1 1)7 × 7 surface. Besides Pb(1 1 1) islands, two additional types of Pb islands are formed: rectangular flat-top Pb(1 0 0) islands and rectangular three-dimensional (3D) Pb islands, and both their orientations rotate by 90° from a terrace to the adjacent one. This phenomenon implies that the structures of Pb(1 0 0) and 3D islands are influenced by the Si(1 0 0)-2 × 1 substrate.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.