Investigation of surface passivation process on magnetic nanoparticles by Raman spectroscopy

A detailed study of the surface passivation process in superparamagnetic cobalt ferrite nanoparticles has been carried out using micro Raman spectroscopy. In addition to Raman spectroscopy, X-ray diffraction and atomic absorption spectroscopy were also used to investigate passivated and non-passivated samples. The data were discussed in terms of changes in the structural characteristics of the samples considering the introduction of Fe ions during the passivation. We found an improvement of the nanoparticle crystallinity due to the passivation process.     

Cytotoxicity and GMI bio-sensor detection of maghemite nanoparticles internalized into cells

In this work we determine conditions to produce cell samples for imaging with detection of the modification of the magnetic field by maghemite (Fe₂O₃) nanoparticles acting as a high sensitivity magnetic bio-sensor based on the giant magneto-impedance (GMI) effect. Mat Ly Lu cells are grown for 24 h with various maghemite nanoparticles concentrations (from 0 to 6 mg/ml). The percentage of viable cells is determined by counting labeled cells with trypan blue under an optical microscope. The quantity of nanoparticles internalized into the cells is evaluated by X-ray fluorescence analysis and expressed in iron moles per cell. The GMI bio-sensor was tested with the various samples. We observed that the best sensitivity of the GMI bio-sensor was obtained at a frequency of 1 MHz. To confirm these results in the presence of cell samples, four measurement frequencies were pre-selected (from 1 to 100 MHz) and tested. Cell growth conditions compatible with an acceptable percentage of cell viability for various concentrations of nanoparticles were also determined. These experiments allow us to conclude that cell growth with 0.1 mg/ml of nanoparticles for 24 h shows modifications of the magnetic field detectable optimally at 1 MHz frequency.     

Surface functionalization of silica-coated magnetic nanoparticles for covalent attachment of cholesterol oxidase

A systematic approach towards the fabrication of highly functionalized silica shell magnetic nanoparticles, presently used for enzyme immobilization, is herein fully presented. The synthesis of bare maghemite (γ-Fe₂O₃) nanoparticles was accomplished by thermal co-precipitation of iron ions in ammonia alkaline solution at harsh reaction conditions, respectively. Primary surface engineering of maghemite nanoparticles was successfully performed by the proper deposition of silica onto nanoparticles surface under strictly regulated reaction conditions. Next, the secondary surface functionalization of the particles was achieved by coating the particles with organosilane followed by glutaraldehyde activation in order to enhance protein immobilization. Covalent immobilization of cholesterol oxidase was attempted afterwards. The structural and magnetic properties of magnetic silica nanocomposites were characterized by TEM and vibrating sample magnetometer (VSM) instruments. X-ray diffraction measurements confirmed the spinel structure and average size of uncoated maghemite nanoparticles to be around 20 nm in diameter. SEM-EDS spectra indicated a strong signal for Si, implying the coating procedure of silica onto the particles surface to be successfully accomplished. Fourier transform infrared (FT-IR) spectra analysis confirmed the binding of amino silane molecules onto the surface of the maghemite nanoparticles mediated Si-O-Si chemical bonds. Compared to the free enzyme, the covalently bound cholesterol oxidase retained 50% of its activity. Binding of enzyme onto chemically modified magnetic nanoparticles via glutaraldehyde activation is a promising method for developing biosensing components in biomedicine.     

Studies on polyethylene glycol coating on NiFe2O4 nanoparticles for biomedical applications

The NiFe₂O₄ nanoparticles were prepared by the combustion method and these nanoparticles were successfully coated with polyethylene glycol (PEG) for the possible biomedical applications such as magnetic resonance imaging, drug delivery, tissue repair, magnetic fluid hyperthermia etc. The structural and magnetic characterizations of NiFe₂O₄ nanoparticles were carried out by x-ray diffraction and vibrating sample magnetometry techniques, respectively. The morphology of the uncoated and coated nanoparticles was studied by scanning electron microscopy. The existence of PEG layer on NiFe₂O₄ nanoparticles was confirmed by fourier transform infrared spectroscopy technique.     

Hydrothermal synthesis of large maghemite nanoparticles: influence of the pH on the particle size

Maghemite nanoparticles with sizes in the range 10–110 nm and good monodispersity have been synthesized by co precipitation at room temperature from Fe²⁺ and Fe³⁺ ions by a (N(CH₃)₄OH) solution, followed by an hydrothermal treatment at 200 °C and an oxidation step with Fe(NO₃)₃. The influence of the incubation time (at 200 °C) and of the pH of the autoclaved solution on the particles size has been studied. It was found that the pH value allows to tune the size of the maghemite particles. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Magnetic hyperthermia with biphasic gel of La1−xSrxMnO3 and maghemite

Magnetic hyperthermia experiments were carried out using a biphasic gel of La_1−xSr_xMnO₃(LSMO) and γ-Al_0.07 Fe_1.93O₃ with an AC magnetic field of amplitude 88 mT and a frequency of 108 kHz. Specific absorption rate (SAR) increases with the increased ratio of Al-substituted maghemite. The T_max value for the gels prepared by the mixture of LSMO and Al-substituted maghemite can be adjusted to suit therapeutic temperature. The time required to reach optimum temperature decreased with the increased ratio of later. Such biphasic gel could be very useful for magnetic hyperthermia with in vivo control of temperature.     

Effects of pressure on maghemite nanoparticles with a core/shell structure

The magnetic property and intraparticle structure of the γ phase of Fe₂O₃ (maghemite) nanoparticles with a diameter (D) of 5.1±0.5 nm were investigated through AC and DC magnetic measurements and powder X-ray diffraction (XRD) measurements at pressures (P) up to 27.7 kbar. Maghemite originally exhibits ferrimagnetic ordering below 918 K, and has an inverse-spinel structure with vacancies. Maghemite nanoparticles studied here consist of a core with structural periodicity and a disordered shell without the periodicity, and core shows superparamagnetism. The DC and AC susceptibilities reveal that the anisotropy energy barrier (ΔE/k_B) and the effective value of the core moment decrease against the initial pressure (P≤3.8 kbar), recovering at P≥3.8 kbar. The change of ΔE/k_B with P is qualitatively identical with that of the core moment, suggesting a down-and-up fluctuation of the number of Fe³⁺ ions constituting the core at the pressure threshold of about 4 kbar. This phenomenon was confirmed by the analysis of the XRD measurement using Scherrer’s formula. The core volume decreased for P≤2.5 kbar, whereas at higher pressure the core was restructured. For 2.5≤P≤10.7 kbar, the volume shrinkage of particle hardly occurs. There, ΔE/k_B is approximately proportional to the volume associated to the ordered fraction of the nanoparticles as seen from XRD, V_core. From this dependence it is possible to separate the core/shell contribution to ΔE/k_B and estimate core and surface anisotropy constants. As for the structural experiments, similar experimental data have been obtained for D=12.8±3.2 nm as well.     

纳米银粒子表面增强拉曼光谱在宠物饲料中三聚氰胺的速测研究

研究将制备的纳米银粒子作为表面增强拉曼光谱的增强试剂,实现对宠物饲料中三聚氰胺的快速定性定量分析。以709与1542cm-1处拉曼位移作为定性依据,以1149cm-1峰强度作为归一化标准,在1.0～10.0mg·kg-1浓度范围实现定量计算,检测限0.5mg·kg-1。研究发现,纳米银粒子对三聚氰胺具有较强的拉曼增强效应,特征峰信号强度与纳米银粒子加入时间,溶液涡旋强度有很大的关系,同时也受提取溶剂的种类、提取方式及样品加入量的影响。本方法中每个样品5min内完成分析,与现有方法相比,快速简便,对宠物饲料中三聚氰胺实现现场、快速检测。     

Raman spectra of benzoic acid enhanced by the silver nanoparticles of various sizes

Using sodium borohydride as the reducing agent and polyvinyl pyrrolidone (PVP, MW = 10 000) as the stabilizer, we obtained silver nanoparticles of various diameters (8–78 nm) from silver nitrate aqueous solutions in the concentration range from 0.001 to 0.1 M. The surface‐enhanced Raman scattering (SERS) from benzoic acid's ring‐breathing mode at 1003 cm⁻¹ was detected from its dilute solutions (∼10⁻² M) doped with these silver nanoparticles under 488‐nm laser excitation. The observed size dependences of SERS intensities fit quite well with those calculated by Schatz's theoretical model for spherical silver nanoparticles. The only exception occurred with the smallest particles (8 nm), possibly due to the failure of Maxwell's electromagnetic theory used in this model. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation of size-controlled nanoparticles of magnetite

Samples of ferrofluids containing chemically stabilized nanoparticles of magnetite (Fe₃O₄) with tetramethylammonium hydroxide (TMAOH) were prepared by a direct reduction–precipitation method. The influences of aging time and temperature on the size and monodispersion characteristics of the produced nanoparticles were investigated. Transmission electron microscopy, powder X-ray diffraction, Fourier-transform infrared, and magnetization measurements with applied magnetic field up to 2 T were used to characterize the synthesized iron oxides. Raising the temperature of the synthesized material in autoclave affects positively the monodispersion of the nanoparticles, but it was not found to significantly influence the size itself of individual particles.     

Effect of surface ZnO coatings on oxidation and thermal stability of zinc films

The effect of thin ZnO coatings grown on Zn films on further oxidation and thermal stability of Zn films deposited on Mo(110) substrate was in situ investigated under ultrahigh vacuum by photoelectron spectrometries and low-energy electron diffraction. The results indicated that ZnO layers formed by oxidizing Zn films had at least a thickness of 3–5 monolayers. Further oxidation of Zn films was confined by as-formed ZnO coatings due to a surface passivation. It was of advantage to explain the difficulty in growing low oxygen-deficient ZnO films. The surface ZnO coatings strongly enhanced the thermal stability of Zn films, which was useful for understanding the underlying application of Zn/ZnO materials, such as Zn/ZnO nanocables with Zn core and ZnO shell.     

Producing ultra-thin silica coatings on iron-oxide nanoparticles to improve their surface reactivity

The reactivity of the relatively inert surfaces of iron-oxide magnetic nanoparticles can be significantly improved by coating the surfaces with silica. Unfortunately, however, this nonmagnetic silica layer tends to dilute the magnetic properties of the nanoparticles. Therefore, the silica layer should be as continuous, homogeneous, and as thin as possible.In this investigation we coated superparamagnetic maghemite nanoparticles by hydrolysis and the polycondensation of tetraethyl orthosilicate (TEOS), with the ethanol solution of TEOS being added to a stable suspension of citric acid-coated nanoparticles. The influences of the various parameters of the procedure on the quality of the coatings were systematically evaluated. The quality of the silica layer was characterized using electron microscopy and by performing leaching of the nanoparticles in HCl, while the surface reactivity was tested by grafting (3-aminopropyl) triethoxysilane (APS) onto the nanoparticles. We observed that the surface concentration of the grafted APS strongly increased when the nanoparticles were coated with a silica layer. The choice of experimental conditions for the coating procedure that favors the heterogeneous nucleation of silica on the surfaces of the nanoparticles enabled the preparation of very thin silica layers, less than 2 nm thick. By decreasing the amount of added TEOS to correspond to a monolayer of -Si-OH at the nanoparticles' surfaces, their surface reactivity could be very much improved, and with a reduction in their magnetization of only ∼10%.     

Heat dissipation and magnetic properties of surface-coated Fe3O4 nanoparticles for biomedical applications

In this study, the influence of surface coating on the magnetic and heat dissipation properties of Fe₃O₄ nanoparticles was investigated. Fe₃O₄ nanoparticles that ranged in size between (particle sizes of 20 and 30 nm) were coated with polyethylenimine (PEI), oleic acid, and Pluronic F-127. Surface coatings that were composed of thick layers of oleic acid and Pluronic F-127 reduced dipole interactions between the particles, and resulted in reduced coercivity and decreased Néel relaxation times. The ac magnetization measurements revealed that the heat dissipation of the PEI-coated Fe₃O₄ nanoparticles was induced by hysteresis loss and Brownian relaxation loss and that of the oleic-acid-coated Fe₃O₄ nanoparticles was mainly induced by hysteresis loss and Néel relaxation loss.     

Sonochemical immobilization of noble metal nanoparticles on the surface of maghemite: mechanism and morphological control of the products

Aqueous sample solutions containing noble metal ions (HAuCl₄, Na₂PdCl₄, H₂PtCl₆), polyethyleneglycol monostearate, and magnetic maghemite nanoparticles were irradiated with high power ultrasound. Analyses of the products showed that noble metal ions were reduced by the effects of ultrasound, and the formed noble metal nanoparticles were uniformly immobilized on the surface of the maghemite. The present “one pot process” significantly simplifies the immobilization of noble metal nanoparticles on the surface of supports, compared with the conventional impregnation method. The average diameter of immobilized Au was 7–13 nm, and the diameters of Pd and Pt were several nm. The diameters depended upon the concentration of polyethyleneglycol monostearate and the concentration of noble metal ions, but not upon the maghemite concentration, indicating the possibility of the morphological controls of the products by adjusting these preparation conditions. The measurements of the average diameters and the numbers of immobilized Au nanoparticles obtained under various conditions suggest that the nucleation of Au does not occur on the surface of maghemite, but it might occur in the homogeneous bulk solution.     

基于银胶纳米颗粒的痕量三硝基甲苯的表面增强拉曼光谱的实验研究

近年来对作为典型的硝基苯环类炸药的三硝基甲苯(TNT)的痕量检测受到越来越多的关注。将银胶纳米颗粒作为表面增强拉曼散射(SERS)基底,研究了10-6 mol.L-1的TNT的表面增强拉曼光谱的优化实验条件,重点研究了氯化钠溶液(NaCl)的含量以及碱性水解对TNT的表面增强拉曼光谱的影响。实验发现SERS样品中如果没有加入NaCl溶液,将观察不到TNT的SERS谱。加入的NaCl的含量必须在某一个范围之内才能观察到TNT的SERS谱,而且在这个范围之内,随着NaCl含量的增加,TNT的1 392cm-1处的拉曼峰出现先增大后减小的现象。对NaCl在TNT的SERS中的作用给予了理论解释。研究还发现TNT分子经过碱性水解后,与银纳米颗粒之间的吸附作用增强,其SERS谱的强度明显优于未经碱性水解的SERS结果。     

Surface coating of Al nanoparticles by using a wet ball milling method: A facile synthesis and characterization of colloidal stability

A facile surface coating of aluminum (Al) nanoparticles with various dispersants by using a wet ball milling method is reported. Various mixtures of Al nanoparticles (d = 30–130 nm) and dispersants in solvent were ball milled. The excellent surface coating was observed with coating thickness ranging from 10 to 13 nm. The resulting good colloidal stability confirmed by both visual inspection of colloidal precipitation and Turbiscan backscattering was attributed to a stable dispersant organic layer formed on Al nanoparticle surfaces after ball milling as observed in HRTEM images. This method can be extended to the synthesis of a variety of any other metallic nano-colloidal solutions.     

Characterizing the coating and size-resolved oxidative stability of carbon-coated aluminum nanoparticles by single-particle mass-spectrometry

Aluminum nanoparticles are of significant interest in enhancing the rate of energy release from propellants. One of the major impediments to their use is that bare aluminum is highly reactive, while oxide coated aluminum significantly decreases overall performance. We investigate creating aluminum nanoparticles with a thin carbon coating using either a laser induced plasma or a DC plasma-arc. The carbon coating was created by injecting ethylene (C₂H₄) directly downstream of the plasma. The elemental composition of the coated aluminum nanoparticles was measured in real time with a recently developed quantitative single particle mass spectrometer (SPMS). We found that the aluminum nanoparticles were coated with a carbon layer of thickness around 1–3 nm.The thermal and oxidative stability of these particles was determined by passing the aerosols through a heated flow reactor in a carrier flow of either air or argon, and measuring the aluminum, carbon and oxygen content in the particles with the single particle mass spectrometer. We found that below 700°C the coating was stable, but that the coating oxidized above ∼ ∼800°C. In contrast the carbon coating was thermally stable above ∼ ∼900°C. These results indicate that a carbon coating may be a suitable passivating agent.     

氟虫氰表面增强拉曼光谱的密度泛函理论研究（英文）

2017年8月初,荷兰发现大范围鸡蛋受杀虫剂氟虫腈污染。用拉曼光谱检测的方法对解决氟虫腈检测问题做了一定的探索。为了获得氟虫腈分子的分子结构振动信息,根据密度泛函理论中的B3LYP杂化泛函和6-311G++(d,p)基组,对氟虫腈分子进行了几何结构优化和频率计算,得到了该分子的稳定构型和全部振动模式,计算了氟虫腈分子稳定构型的拉曼散射光谱。利用HORIBA公司的T64000型光栅共聚焦显微拉曼光谱仪采集了FP的拉曼光谱并配合使用Ag/Cu纳米基底采集了表面增强拉曼光谱,较强峰出现在211,308,350,867,1323和1432 cm-1处,次强峰出现在254,407,443,463,511,607,646,712,800,1065和1639 cm-1处。结果表明,理论计算得到的振动频率与实验测量值在全部较强峰处和部分次强峰处吻合的较好。并对FP分子200~2000 cm-1区间内各频率谱线对应的振动模式进行了归属指认,6个较强峰依由小到大的次序分别指认为21H-22H蜷曲振动,10F-11F变形振动和21H-22H面外摇摆振动,15N-22H蜷曲振动,6C伸缩振动和21H面内弯曲振动,苯环呼吸振动和9C伸缩振动,7H-8H面内弯曲振动。发现表面增强拉曼光谱相对于拉曼光谱整体有微小的频移,两者整体吻合较好,表面增强拉曼光谱中211,867,1400和1432 cm-1处的峰得到了选择性增强,根据表面增强拉曼光谱的选择定则,解释为相关振动峰的原子与银衬底表面或许为接近垂直的状态,并可能与银表面吸附。下一步计划将氟虫腈混入鸡蛋中,对氟虫腈在鸡蛋中不同浓度情况下进行指认研究。研究结果可为氟虫腈的拉曼光谱分析提供理论依据,将促进食品和农产品中氟虫腈残留的快速检测和在线检测研究。将拉曼光谱作为对传统化学检测方法的补充。     

Radial vibration of ultra-small nanoparticles with surface effects

An elastic model to predict radial vibration of ultra-small nanoparticles is proposed and the main reason of frequency shifts (comparing with classical elastic model) in ultra-small nanoparticles is interpreted. Taking the curvature-dependent surface theory into account, the effects of surface on the radial vibrations of nanoparticles are investigated with our new model. Both the atomic and the present models are calculated and their results agree well. It argues that the surface effects are remarkable on the radial vibrations of ultra-small nanoparticles and surface elasticity plays the main role rather than surface stress which is the previous understanding. The curvature-dependence of surface effects cannot be ignored when the particle is small enough. For the low-order radial vibration, the surface effects are more noteworthy.