Emulsion copolymerization of styrene and methyl methacrylate

Chain transfer constants to monomer have been measured by an emulsion copolymerization technique at 44°C. The monomer transfer constant (ratio of transfer to propagation rate constants) is 1.9 × 10^?5 for styrene polymerization and 0.4 × 10^?5 for the methyl methacrylate reaction. Cross-transfer reactions are important in this system; the sum of the cross-transfer constants is 5.8 × 10^?5. Reactivity ratios measured in emulsion were r₁ (styrene) = 0.44, r₂ = 0.46. Those in bulk polymerizations were r₁ = 0.45, r₂ = 0.48. These sets of values are not significantly different. Monomer feed compcsition in the polymerizing particles is the same as in the monomer droplets in emulsion copolymerization, despite the higher water solubility of methyl methacrylate. The equilibrium monomer concentration in the particles in interval-2 emulsion polymerization was constant and independent of monomer feed composition for feeds containing 0.25–1.0 mole fraction styrene. Radical concentration is estimated to go through a minimum with increasing methyl methacrylate content in the feed. Rates of copolymerization can be calculated a priori when the concentrations of monomers in the polymer particles are known.     

Silyl enol ethers as monomer. III. Radical polymerization and copolymerizations of 2-trimethylsilyloxy-1,3-butadiene and desilylation of the resulting polymers

2-Trimethylsilyloxy-1,3-butadiene (TMSBD), the silyl enol ether of methyl vinyl ketone, was homopolymerized with a radical initiator to afford polymers with a molecular weight of ca. 10⁴. Radical copolymerizations of TMSBD with styrene (ST) and acrylonitrile (AN) in bulk or dioxane at 60°C gave the following monomer reactivity ratios: r₁ = 0.64 and r₂ = 1.20 for the ST (M₁)–TMSBD (M₂) system and r₁ = 0.036 and r₂ = 0.065 for the AN (M₁)–TMSBD (M₂) system. The Q and e values of TMSBD determined from the reactivity ratios for the former copolymerization system were 2.34 and ?1.31, respectively. The resulting polymer and copolymers were readily desilylated with hydrochloric acid or tetrabutylammonium fluoride as catalyst to yield analogous polymers having carbonyl groups in the polymer chains.     

Tapered copolymers of styrene and 4-vinylbenzocyclobutene via carbanionic polymerization for crosslinkable polymer films

Well-defined polystyrene homopolymers with surface-adhesive triethoxysilyl end group were synthesized via living carbanionic polymerization, epoxide end-functionalization and subsequent hydrosilylation with triethoxysilane. Grafting-to performance of polymers with various molecular weight (M_n = 3000–14,000 g mol⁻¹) to a silicon surface was examined in dependence of reaction time, polymer concentration, solvent and number of alkoxysilyl end groups. Crosslinkable polymers for surface modification were synthesized by statistical carbanionic copolymerization of 4-vinylbenzocyclobutene (4-VBCB) and styrene, followed by epoxide end-functionalization and triethoxysilane modification (M_n = 4000–14,000 g mol⁻¹). The copolymers were characterized by ¹H-NMR, THF-SEC, and matrix-assisted laser desorption and ionization time-of-flight mass spectrometry. In situ ¹H-NMR kinetic studies in cyclohexane-d₁₂ provided information regarding the monomer gradient in the polymer chains, with styrene being the more reactive monomer (r_s = 2.75, r_4-VBCB = 0.23). Thin polymer films on silicon wafers were prepared by grafting-to surface modification under conditions derived for the polystyrene homopolymer. The traceless, thermally induced crosslinking reaction of the benzocyclobutene units was studied by DSC in bulk as well as in 3–6 nm thick polymer films. Crosslinked films were analyzed by atomic force microscopy, ellipsometry, and nanoindentation, showing smooth polymer films with an increased modulus. © 2019 The Authors. Journal of Polymer Science published by Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 181–192     

Aminobutadienes. X. Polymerization and copolymerization of 2-phthalimidomethyl-1,3-butadiene

The polymerization and copolymerization of 2-phthalimidomethyl-1,3-butadiene were investigated. This monomer was easily polymerized by benzoyl peroxide catalyst in bulk or in solvent, and by γ-radiation in the solid state to give polymers having a softening point of 135–145°C. Although these resulting polymers did not give x-ray diffraction patterns, they showed crystalline patterns by electron diffraction. On the other hand, cationic polymerization with the use of boron trifluoride diethyl etherate in chloroform was attempted, but no formation of the polymer was observed. Also, this monomer was easily copolymerized with styrene in N,N-dimethylformamide. The monomer reactivity ratios and Alfrey-Price Q and e values calculated from the copolymerization data of this monomer (M₁) with styrene (M₂) were r₁ = 2.0 ± 0.13, r₂ = 0.15 ± 0.02, and Q₁ = 2.78, e₁ = 0.30.     

Junction‐Controlled Topological Polymerization

Methodology that enables the controlled synthesis of linear and branched polymers from an identical monomer will be a novel pathway for polymer synthesis and processing. Herein we first describe the control of one or both of the C(3)‐C(3′) and C(6)‐C(6′) coupling reactions of carbazolyl. In a second approach, an identical monomer containing two carbazolyls is polymerized using chemical and electrochemical oxidizers, leading to topologically controllable growth of linear polymers in weak oxidizer or of cross‐linked polymer chains in strong oxidizer, with satisfactory long chain propagation of step growth polymerization (M_n=6.0×10⁴ g mol^?1, M_w/M_n=2.3). This very simple polymerization with cheap reagents and low levels of waste has provided a flexible pathway for synthesis and processing of polymers.     

Initiator effect on the cationic ring‐opening copolymerization of 2‐ethyl‐2‐oxazoline and 2‐phenyl‐2‐oxazoline

The aim of this research was to study the effect of the initiator on the resulting monomer distribution for the cationic ring‐opening copolymerization of 2‐ethyl‐2‐oxazoline (EtOx) and 2‐phenyl‐2‐oxazoline (PhOx). At first, kinetic studies were performed for the homopolymerizations of both monomers at 160 °C under microwave irradiation using four initiators. These initiators have the same benzyl‐initiating group but different leaving groups, Cl^?, Br^?, I^?, and OTs^?. The basicity of the leaving group affects the ratio of covalent and cationic propagating species and, thus, the polymerization rate. The observed differences in polymerization rates could be correlated to the concentration of cationic species in the polymerization mixture as determined by ¹H NMR spectroscopy. In a next‐step, polymerization kinetics were determined for the copolymerizations of EtOx and PhOx with these four initiators. The reactivity ratios for these copolymerizations were calculated from the polymerization rates obtained for the copolymerizations. This approach allows more accurate determination of the copolymerization parameters compared to conventional methods using the composition of single polymers. When benzyl chloride (BCl) was used as an initiator, no copolymers could be obtained because its reactivity is too low for the polymerization of PhOx. With decreasing basicity of the used counterions (Br^? > I^? > OTs^?), the reactivity ratios gradually changed from r_EtOx = 10.1 and r_PhOx = 0.30 to r_EtOx = 7.9 and r_PhOx = 0.18. However, the large difference in reactivity ratios will lead to the formation of quasi‐diblock copolymers in all cases. In conclusion, the used initiator does influence the monomer distribution in the copolymers, but for the investigated system the differences were so small that no difference in the resulting polymer properties is expected. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4804–4816, 2008     

Copolymerization of anhydroglucose and anhydromannose derivatives: Structure,reactivity, and conformational analyses

Phosphorus pentafluoride-catalyzed copolymerization of 1,6-anhydro-2,3,4-tri-O-(p-methylbenzyl)-β-D -glucopyranose (TXGL, monomer G) and 1,6-anhydro-2,3,4-tri-O-benzyl-β-D -mannopyranose (TBMN, monomer M) appears to follow classical copolymerization theory. Reactivity ratios calculated by the procedure of Mayo and Lewis were r_G = 0.90 ± 0.08, r_M = 11.5 ± 0.80, from which sequence distributions were calculated. A conformational analysis of anhydro sugar polymerization is presented to explain differences in reactivity of monomers and their derived cations in polymerization and copolymerization. The polymers and copolymers were characterized by viscosity, ¹H- and ¹³C-NMR spectroscopy, optical rotation, and circular dichroism. The reaction gives stereoregular polymers as have other polymerizations and copolymerizations of this class.     

An experimental study on the kinetics and mechanisms of styrene polymerization in oil‐in‐water microemulsion initiated by oil‐soluble initiators

In order to clarify the kinetic role of oil‐soluble initiators in microemulsion polymerization, the oil‐in‐water (O/W) microemulsion polymerizations of styrene are carried out using four kinds of azo‐type oil‐soluble initiators with widely different water‐solubility. The results are compared with those observed when a water‐soluble initiator, potassium persulfate (KPS) is used. For all the oil‐soluble initiators used, the molecular weight of polymers and the average size of polymer particles do not change with the monomer conversion and the initial initiator concentration. The monomer conversion is expressed as a function of r_i^0.5t, where r_i is the rate of radical generation in the whole reaction system and t is the reaction time. These characteristics are quite the same as those observed when KPS is used as an initiator. When the polymerizations are carried out with the rate of radical generation in the whole reaction system fixed at the same value, the rates of polymerization are almost the same for all the oil‐soluble initiators employed, irrespective of their water‐solubility, but are significantly lower (ca. 1/3) than that with KPS. Then, the following conclusions are given: (1) The radicals generated not only in the aqueous phase, but also in the micelle and polymer particle phase are almost equally effective for the polymerization. However, (2) only a small portion (ca. 1/9) of the radicals generated in both phases participate in the polymerization. (3) Bimolecular termination of a growing radical in the polymer particle with an entering radical and with a pair of radicals generated in the polymer particles is negligible, and hence, the molecular weight of polymers is determined only by chain transfer to monomer.     

Polymerization of vinyl chloride and copolymerization with carbon monoxide by a new initiator

The system comprising the ethoxydized product of triethylaluminum, cuprous chloride, and carbon tetrachloride was used as an initiator for polymerization of vinyl chloride, and the polymerization kinetics was studied. From plots of the molar number of number-average polymer chain Y/P? versus yield Y, the two parameters a ( = ∫ R_idt ? 1/2 ∫ R_tdt) and b ( = ∫ R_trdt/∫ R_pdt) were estimated to be 6 × 10^?3 mole/l. and 6.6 × 10^?4 respectively. Studies of the tacticity of the poly(vinyl chloride) showed isotactic = 49.3% and syndiotactic = 50.7%. The present initiator also permitted copolymerization of vinyl chloride with carbon monoxide; the monomer reactivity ratios were r₁ = 0.40 (vinyl chloride) and r₂ = 0.01 (carbon monoxide).     

Synthesis,characterization, and thin‐film properties of 6‐oxoverdazyl polymers prepared by ring‐opening metathesis polymerization

Redox‐active 6‐oxoverdazyl polymers were synthesized via ring‐opening metathesis polymerization (ROMP) and their solution, bulk, and thin‐film properties investigated. Detailed studies of the ROMP method employed confirmed that stable radical polymers with controlled molecular weights and narrow molecular weight distributions (Ð < 1.2) were produced. Thermal gravimetric analysis of a representative example of the title polymers demonstrated stability up to 190 °C, while differential scanning calorimetry studies revealed a glass transition temperature of 152 °C. Comparison of the spectra of 6‐oxoverdazyl monomer 12 and polymer 13 , including FT‐IR, UV‐vis absorption, and electron paramagnetic resonance spectroscopy, was used to confirm the tolerance of the ROMP mechanism for the 6‐oxoverdazyl radical both qualitatively and quantitatively. Cyclic voltammetry studies demonstrated the ambipolar redox properties of polymer 13 (E_1/2,ox = 0.25 and E_1/2,red = ?1.35 V relative to ferrocene/ferrocenium), which were consistent with those of monomer 12 . The charge transport properties of thin films of polymer 13 were studied before and after a potential of 5 V was applied, revealing a drastic drop in the resistivity from 10⁶?10¹⁰ Ω m or more to 1.7 × 10⁴ Ω m and suggesting the potential usefulness of polymer 13 in bistable electronics. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1803–1813     

Polymerization of 1,3‐dienes with functional groups. II. Free‐radical polymerization of N‐(2‐methylene‐3‐butenoyl)piperidine

The free‐radical homopolymerization and copolymerization behavior of N‐(2‐methylene‐3‐butenoyl)piperidine was investigated. When the monomer was heated in bulk at 60 °C for 25 h without an initiator, about 30% of the monomer was consumed by the thermal polymerization and the Diels–Alder reaction. No such side reaction was observed when the polymerization was carried out in a benzene solution with 1 mol % 2,2′‐azobisisobutylonitrile (AIBN) as an initiator. The polymerization rate equation was found to be R_p ∝ [AIBN]^0.507[M]^1.04, and the overall activation energy of polymerization was calculated to be 89.5 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure that included both 1,4‐E and 1,4‐Z configurations. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were carried out in benzene solutions at 60 °C with AIBN as an initiator. In the copolymerization with styrene, the monomer reactivity ratios were r₁ = 6.10 and r₂ = 0.03, and the Q and e values were calculated to be 10.8 and 0.45, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1545–1552, 2003     

Hydroxyl‐terminated hyperbranched aromatic poly(ether‐ester)s: Synthesis,characterization, end‐group modification,and optical properties

Novel AB₂‐type monomers such as 3,5‐bis(4‐methylolphenoxy)benzoic acid ( monomer 1 ), methyl 3,5‐bis(4‐methylolphenoxy) benzoate ( monomer 2 ), and 3,5‐bis(4‐methylolphenoxy)benzoyl chloride ( monomer 3 ) were synthesized. Solution polymerization and melt self‐polycondensation of these monomers yielded hydroxyl‐terminated hyperbranched aromatic poly(ether‐ester)s. The structure of these polymers was established using FTIR and ¹H NMR spectroscopy. The molecular weights (M_w) of the polymers were found to vary from 2.0 × 10³ to 1.49 × 10⁴ depending on the polymerization techniques and the experimental conditions used. Suitable model compounds that mimic exactly the dendritic, linear, and terminal units present in the hyperbranched polymer were synthesized for the calculation of degree of branching (DB) and the values ranged from 52 to 93%. The thermal stability of the polymers was evaluated by thermogravimetric analysis, which showed no virtual weight loss up to 200 °C. The inherent viscosities of the polymers in DMF ranged from 0.010 to 0.120 dL/g. End‐group modification of the hyperbranched polymer was carried out with phenyl isocyanate, 4‐(decyloxy)benzoic acid and methyl red dye. The end‐capping groups were found to change the thermal properties of the polymers such as T_g. The optical properties of hyperbranched polymer and the dye‐capped hyperbranched polymer were investigated using ultraviolet‐absorption and fluorescence spectroscopy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5414–5430, 2008     

Synthesis and polymerization of N-[4-N′- (α-methylbenzyl)aminocarbonylphenyl]maleimide

A novel type of optically active N-[4-N′-(α-methylbenzyl)aminocarbonylphenyl]maleimide [(R)-MBCP] was synthesized from maleic anhydride, p-aminobenzoic acid, and (R)-methylbenzylamine. Radical homopolymerization of (R)-MBCP was performed in tetrahydrofuran (THF) at 50 and 70°C for 24 h to give optically active polymers having [α]²⁵_D = -141° and -129°, respectively. Anionic polymerization of (R)-MBCP with n-butyllithium in THF and N,N-dimethylformamide gave an optically active polymer having ?78 to ?81° of [α]²⁵_D. Radical copolymerizations of (R)-MBCP (M₁) were performed with styrene (ST, M₂) and methyl methacrylate (MMA, M₂) in THF at 50°C. The monomer reactivity ratios (r₁, r₂) and the Alfrey-Price Q-e values were determined as follows: r₁ = 0.009, r₂ = 0.091, Q₁ = 1.30, e₁ = 1.87 in the (R)-MBCP-ST; r₁ = 0.27, r₂ = 1.21, Q₁ = 0.93, e₁ = 1.46 in the (R)-MBCP-MMA system. Chiroptical properties of the polymers were also investigated. © 1992 John Wiley & Sons, Inc.     

Synthesis of substituted polymethylenes by radical polymerization of N,N,N′,N′-tetraalkylfumaramides and their characterization

Radical polymerization of N,N,N′,N′-tetraalkylfumaramides (TRFAm) bearing methyl, ethyl, n-propyl, isopropyl, and isobutyl groups as N-substituents (TMFAm, TEFAm, TnPFAm, TIPFAm, and TIBFAm, respectively) was investigated. In the polymerization of TEFAm initiated with 1,1′-azobiscyclohexane-1-carbonitrile (ACN) in benzene, the polymerization rate (R_p) was expressed as follows: R_p = k [ACN]^0.28 [TEFAm]^1.26, and the overall activation energy was 102.1 kJ/mol. The introduction of a bulky alkyl group into N-substituent of TRFAm decreased the R_p in the following order: TMFAm > TEFAm > TnPFAm > TIBFAm > TIPFAm ～ 0. The relative reactivities of these monomers were also investigated in radical copolymerization with styrene (St) and methyl methacrylate (MMA). In copolymerization of TRFAm (M₂) with St (M₁), monomer reactivity ratios were determined to be r₁ = 1.07 and r₂ = 0.20 for St–TMFAm, and r₁ = 1.88 and r₂ = 0.11 for St–TEFAm, from which Q₂ and e₂ values were estimated to be 0.35 and 0.44 for TMFAm, and 0.19 and 0.47 for TEFAm, respectively. The other TRFAm were also copolymerized with St, but copolymerization with MMA gave polymers containing a small amount of TRFAm units. The polymer from TRFAm consists of a less-flexible poly(N,N-dialkylaminocarbonylmethylene) structure. The solubility and thermal property of the polymers were also investigated.     

Polymerization of 1,3‐dienes with functional groups. III. Free‐radical polymerization of N,N‐diethyl‐2‐methylene‐3‐butenamide

Free‐radical homo‐ and copolymerization behavior of N,N‐diethyl‐2‐methylene‐3‐butenamide (DEA) was investigated. When the monomer was heated in bulk at 60 °C for 25 h without initiator, rubbery, solid gel was formed by the thermal polymerization. No such reaction was observed when the polymerization was carried out in 2 mol/L of benzene solution with with 1 mol % of azobisisobutyronitrile (AIBN) as an initiator. The polymerization rate (R_p) equation was R_p ∝ [DEA]^1.1[AIBN]^0.51, and the overall activation energy of polymerization was calculated 84.1 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure where both 1,4‐E and 1,4‐Z structures were included. From the product analysis of the telomerization with tert‐butylmercaptan as a telogen, the modes of monomer addition were estimated to be both 1,4‐ and 4,1‐addition. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were also carried out in benzene solution at 60 °C. In the copolymerization with styrene, the monomer reactivity ratios obtained were r₁ = 5.83 and r₂ = 0.05, and the Q and e values were Q = 8.4 and e = 0.33, respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 999–1007, 2004     

Hydroxyl‐ and amine‐terminated hyperbranched polyurethanes using AB2‐type azide monomers: Synthesis,characterization, fluorescence,and charge‐transfer complexation studies

Novel AB₂‐type azide monomers such as 3,5‐bis(4‐methylolphenoxy)carbonyl azide (monomer 1) , 3,5‐bis(methylol)phenyl carbonyl azide (monomer 2) , 4‐(methylol phenoxy) isopthaloyl azide (monomer 3) , and 5‐(methylol) isopthaloyl azide (monomer 4) were synthesized. Melt and solution polymerization of these monomers yielded hydroxyl‐ and amine‐terminated hyperbranched polyurethanes with and without flexible ether groups. The structures of theses polymers were established using FT‐IR and NMR spectroscopy. The molecular weights (M_w) of the polymers were found to vary from 3.2 × 10³ to 5.5 × 10⁴ g/mol depending on the experimental conditions used. The thermal properties of the polymers were evaluated using TGA and DSC: the polymer obtained from monomer ( 1 ) exhibited lowest T_g and highest thermal stability and the polymer obtained from monomer ( 2 ) registered the highest T_g and lowest thermal stability. All the polymers displayed fluorescence maxima in the 425–525 nm range with relatively narrow peak widths indicating that they had pure and intense fluorescence. Also, the polymers formed charge transfer (CT) complexes with electron acceptor molecules such as 7,7,8,8‐tetracyano‐quino‐dimethane (TCNQ) and 1,1,2,2‐tetracyanoethane (TCNE) as evidenced by UV‐visible spectra. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3337–3351, 2009     

Radiation-induced copolymerizations of perfluorovinyl acetic acid and its methyl ester with α-olefin

Homopolymerizations and copolymerizations of perfluorovinyl acetic acid (FVA) and its methyl ester (MFVA) were carried out by γ radiation at a temperature of 25°C, a dose rate of 1 × 10⁶ rad/hr, and FVA/α-olefin and MFVA/α-olefin ratios of 10/90-90/10 in the monomer mixture. FVA and MFVA gave small quantities of brown and greasy low-molecular-weight homopolymers. The polymerization rates of both FVA and MFVA were extremely small, as shown by the maximum G value of monomer consumption of 12. FVA and MFVA reacted with α-olefin to form waxlike copolymers. The copolymerization rates of both FVA and MFVA with α-olefin were remarkably larger than those of the homopolymerizations, particularly with ethylene. The polymer compositions of FVA/ethylene or MFVA/ethylene was nearly 1/2 over a wide range of the monomer compositions. The Mayo–Lewis method gave negative r₁ (FVA) and r₁ (MFVA). The polymer composition curves could be well interpreted by introducing the penultimate model.     

Polymerization behaviour of 2,5-dimethylene- 2,5-dihydrofuran

Spontaneous homopolymerization of 2,5-dimethylene-2,5-dihydrofuran (DDF) was studied. The polymerization rates in two different initial monomer concentrations of DDF were analyzed with the first-order and second-order kinetics, and the homopolymerization of DDF was found to obey the first-order kinetics. The Arrhenius plot of the apparent rate constants at 30, 40, 50, and 60° gave an overall activation energy of 68.0 kJ/mol for the polymerization of DDF. From the comparison of the apparent rate constants at –78° and the time (the so-called half-life time) to decrease in half the monomer concentration for DDF with the corresponding values for p-xylylene (QM), DDF was found to be a less reactive monomer than QM. The copolymerizations of DDF with vinyl monomers such as acrylonitrile (AN), α-chloroacrylonitrile (CIAN), diethyl fumarate (DEF), and fumaronitrile (FN) were carried out in chloroform at 50° in the presence of AIBN to obtain the monomer reactivity ratios r₁(DDF) = 30.0 ± 3.0 and r₂ (AN) = 0 for the DDF-AN system, r₁ (DDF) = 1.55 ± 0.2 and r₂(CIAN) = 0 for the DDF-CIAN system, r₁(DDF) = 3.88 ± 0.2 and r₂(DEF) = 0 for the DDF-DEF system, and r₁(DDF) = 2.41 ± 0.1 and r₂ (FN) = 0 for the DDF-FN system, respectively. As the monomer reactivity ratios of r₂ for all systems were zero, Q and e values of DDF were calculated from the combination of two r₁ (DDF) values of any two copolymerization systems to be the 7.64 to 6.63 ×10²¹ range for Q and the –0.70 to –6.31 range for e, indicating that DDF is a highly conjugative and electron-donating monomer. © 1995 John Wiley & Sons, Inc.     

ROMP of t-butyl-substituted ferrocenophanes affords soluble conjugated polymers that contain ferrocene moieties in the backbone

A substituted ferrocenophane, 1,1′-((1-tert-butyl)-1,3-butadienylene)ferrocene, was synthesized and polymerized via ring-opening metathesis polymerization (ROMP) to give soluble high molecular weight polymers with ferrocenylene units in the backbone. The monomer readily underwent polymerization upon exposure to a tungsten-based metathesis initiator, W(CHC₆H₄-o-OMe)(NPh)[OCMe(CF₃)₂]₂ (THF), to give high molecular weight polymers (M_w=ca. 300,000). The molecular weights could be varied systematically by adjusting the monomer-to-catalyst ratio. UV/vis spectra revealed a bathochromic shift for the polymer, consistent with enhanced conjugation compared to the monomer. The polymer exhibited thermal properties similar to oligomeric poly(ferrocenylene). Cyclic voltammetry of the polymer suggested that the iron centers are coupled electronically. Upon doping with I₂ vapor, the polymers displayed semiconducting properties (σ=10⁻⁵ S cm⁻¹). Theoretical calculations were used to evaluate the nature of the bonding in these and related polymers.     

Polymerization of 1-aryl-2-trimethylsilylacetylenes by transition metal catalysts(II)

Polymerization of 1-aryl-2-trimethylsilylacetylene (aryl = thienyl, furyl, and pyridyl) was carried out by transition metal catalysts. The polymer yield was generally low due to the steric hindrance. R₄Sn (R = Me, n-Bu, Ph) exhibits some cocatalytic activities with respect to polymer yield and molecular weight. On the other hand, the polymerization was decelerated when organoaluminum compounds were used as cocatalysts. The polymer yield increased in the following order: phenyl > thienyl > furyl > pyridyl, according to the aryl substituents. The NMR (¹H- and ¹³C-), IR, and UV-visible spectra indicated that the resulting polymers have a linear conjugated polyene structure each containing the aromatic substituent and trimethylsilyl group. From ¹H-NMR integration, it was found that the resulting polymers are partially desilylated depending on the substituents of monomer and the polymerization conditions. The solubility behavior, stability and fluoride-ion induced desilylation reaction of the polymers were also studied.