自组装和共缩聚法制备磺酸基修饰的硅柱磷酸锆

以十六胺插层磷酸锆为原料, 利用十二烷基二甲基苄基氯化铵为导向模板剂, 通过正硅酸乙酯和巯丙基三甲氧基硅烷的层间共水解缩聚, 并结合双氧水对巯丙基的熏蒸氧化, 制备了磺酸基修饰的硅柱磷酸锆材料。通过XRD、SEM、N2吸附-脱附和FT-IR等方法对柱撑材料进行了结构表征。结果表明, 通过调变预撑剂和模板剂中的碳链长度可以优化材料的柱撑结构和孔结构, 磺酸基修饰的材料孔径分布在2.17 nm左右, 比表面积可达163 m²·g^-1, 且保留有规整有序的柱撑磷酸锆层板结构。磺酸基的修饰则成功调变了材料的酸位性质, Brönsted酸量最高可达2.71 mmol·g^-1, 总酸量可达5.20 mmol·g^-1。利用柠檬酸与正丁醇的酯化反应为探针反应, 由于磺酸基修饰的硅柱磷酸锆材料具有独特的空间反应效应和较为丰富的Brönsted酸位, 酯化反应转化率最高可达95.74%。     

自组装和共缩聚法制备磺酸基修饰的硅柱磷酸锆

以十六胺插层磷酸锆为原料,利用十二烷基二甲基苄基氯化铵为导向模板剂,通过正硅酸乙酯和巯丙基三甲氧基硅烷的层间共水解缩聚,并结合双氧水对巯丙基的熏蒸氧化,制备了磺酸基修饰的硅柱磷酸锆材料。通过XRD、SEM、N2吸附-脱附和FT-IR等方法对柱撑材料进行了结构表征。结果表明,通过调变预撑剂和模板剂中的碳链长度可以优化材料的柱撑结构和孔结构,磺酸基修饰的材料孔径分布在2.17 nm左右,比表面积可达163 m2·g-1,且保留有规整有序的柱撑磷酸锆层板结构。磺酸基的修饰则成功调变了材料的酸位性质,Br觟nsted酸量最高可达2.71 mmol·g-1,总酸量可达5.20 mmol·g-1。利用柠檬酸与正丁醇的酯化反应为探针反应,由于磺酸基修饰的硅柱磷酸锆材料具有独特的空间反应效应和较为丰富的Br觟nsted酸位,酯化反应转化率最高可达95.74%。     

Synthesis and Characterization of Monofunctionalized Polyhedral Oligomeric Silsesquioxanes by Cohydrolytic and Cocondensation of Propyltrimethoxysilane and Vinyltrimethoxysilane

A monofunctional POSS [Si₈O₁₂(CH?CH₂)(C₃H₇)₇] was synthesized by the cohydrolysis and cocondensation of propyltrimethoxysilane and vinyltrimethoxysilane in methanol solvent under acidic conditions. Then, the structure of the product was investigated using FT-IR, ¹H-NMR, ²⁹Si-NMR and XRD. Experimental results indicated that the mole rate of propyls and vinyls attached on POSS was approximately 7:1, which was controlled through altering the ratio of two monomers. Furthermore, the TGA result also showed a rapid mass loss began at temperature over 218°C due to the degradation or sublimation of POSS itself. The new method, in comparison with the conventional corner-capping method, offered us another simple and effective access to preparing this kind of monofunctional POSS.     

Structure–property relationships of anionic poly(urethane–urea) dispersion cross-linked with partially methylated melamine formaldehyde

An anionic poly(urethane–urea) dispersion (PUD) was cross-linked with different amount of partially methylated melamine formaldehyde (PMMF). The isothermal curing behavior was observed by a rigid-body pendulum rheometer. The test results showed that cure response of PUD cross-linked with PMMF was a function of the concentration of PMMF. Also, PMMF self-condensation could take place during the curing process. In this experiment, the anionic poly(urethane–urea) dispersion has a large number of >N–H cross-linking or branching sites in urethane and urea groups per molecule that allow a large number of PMMF to couple into elastic PUD backbone to form branched structure with partial cross-linking. The dynamic mechanical properties of PUD cross-linked with PMMF were affected by the concentration of PMMF. It was further shown that the tensile properties were strongly influenced by the concentration of PMMF and curing temperature.     

Preparation of urea formaldehyde microsphere and its effect on flame retardant ethylene vinyl acetate composites

Urea formaldehyde microsphere (UFM) was prepared and used with organic montmorillonite (OMMT) to modify the flame retardant efficiency of ethylene vinyl acetate copolymer (EVA)/intumescent flame retardant (IFR) composites. The results show that single IFR may modify the flame retardancy of EVA, but its efficiency is not good enough. The EVA composite containing 21 wt% IFR is just classified the UL_94 V2 and has a limiting oxygen index (LOI) 24.7 vol%. Combining UFM with IFR does not improve the flame retardancy of EVA/IFR composites, and blending OMMT with IFR only improves its LOI. Adding 2 wt% UFM, 2 wt% OMMT, and 17 wt% IFR into EVA, it obtains the UL_94 V0 without melt dripping and a LOI 29.0 vol%. Also, the peak heat release rate and total heat release decrease a lot. Good synergistic effects among IFR, UFM, and OMMT improve the char residues and modify the char micromorphology of EVA composites, which provide better protect for the underlying resin.     

Displacement washing of pulp with urea solutions

Two basic mechanisms of displacement washing of pulp fibres were investigated. Experiments were carried out in a laboratory washing cell that simulated a single stage of displacement washing. The step-change method has been employed in investigation of alkali lignin profile in outlet stream of washing effluents. The addition of urea to wash water resulted in a decrease of the liquid layer immobilized on the fibre surface. It had a positive effect on the washing efficiency expressed in terms of the void local efficiency. Presented at the 33rd International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 22–26 May 2006.     

Removal of proteins from natural rubber with urea

Removal of proteins from natural rubber was achieved by incubation of the rubber latex with urea in the presence of a surfactant to prevent the latex‐allergy caused with thin film products. Temperature, pH and time for the incubation were investigated to remove the proteins effectively, in which nitrogen content of the rubber was reduced to 0.02 from 0.38 wt% under the optimum condition. To remove further the proteins, deproteinization of natural rubber was made by incubation of the latex with proteolytic enzyme in the presence of a surfactant followed by incubation with urea. Amount of allergen decreased through the procedure to less than 0.7 μg/ml, which is a small amount of allergen compared to that for the commercial, deproteinized natural rubber. Copyright © 2004 John Wiley & Sons, Ltd.     

Aromatic polyamides with pendant urea moieties

This work describes six novel aromatic polyamides with bulky pendant groups, each having a polyisophthalamide backbone substituted with different urea groups in ring position 5 of the diacid or the diamine residue. Thus, one of the nitrogen atoms of the urea is chemically anchored to the main rigid polyamide chain, while the other nitrogen atom is substituted by phenyl, nitrophenyl, naphthyl, and phenylureidophenyl groups. The polyamides are amorphous and soluble in polar aprotic solvents. They demonstrate a film‐forming capability with outstanding mechanical properties, and exhibit moderate thermal resistance in nitrogen and oxygen atmospheres. The urea group imparts hydrophilicity to the polymers, and facilitates the future preparation of specialty polymers through the easy chemical modification of this group. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4026–4036, 2007     

Synthesis of methyl N-phenyl carbamate from dimethyl carbonate and 1,3-diphenyl urea under mild conditions

Synthesis of methyl N-phenyl carbamate from dimethyl carbonate and 1,3-diphenyl urea was investigated under atmospheric pressure. The results showed that homogenous catalyst sodium methoxide had the excellent activity to efficiently catalyze the synthesis of methyl N-phenyl carbamate under atmospheric pressure.     

Interaction of urea and urea derivatives with cyclohexamylose in aqueous solutions at 25°C

The interaction in water of urea, monomethylurea, monoethylurea, monopropylurea, and monobutylurea with -cyclodextrin(hexacycloamylose) was studied calorimetrically at 25°C. The results show that the last three substances form inclusion complexes with -cyclodextrin. The enthalpy and the association constants relative to the inclusion process were determined. The association constant values are low, indicating weak complexing that increases with increasing length of the alkyl chain. Urea and monomethylurea, on the other hand, do not form inclusion complexes. For these systems the calorimetric data were treated in terms of excess enthalpies, and the McMillan-Mayer approach was used to get an insight into the weak, non-bonding molecular interactions occurring in these solutions.Presented at the sixth Italian meeting on Calorimetry and Thermal Analysis (AICAT) held in Naples, December 4–7, 1984.     

Rapid dissolution of cellulose in LiOH/urea and NaOH/urea aqueous solutions

Rapid dissolution of cellulose in LiOH/urea and NaOH/urea aqueous solutions was studied systematically. The dissolution behavior and solubility of cellulose were evaluated by using (13)C NMR, optical microscopy, wide-angle X-ray diffraction (WAXD), FT-IR spectroscopy, DSC, and viscometry. The experiment results revealed that cellulose having viscosity-average molecular weight ((overline) M eta) of 11.4 x 104 and 37.2 x 104 could be dissolved, respectively, in 7% NaOH/12% urea and 4.2% LiOH/12% urea aqueous solutions pre-cooled to -10 degrees C within 2 min, whereas all of them could not be dissolved in KOH/urea aqueous solution. The dissolution power of the solvent systems was in the order of LiOH/urea > NaOH/urea > KOH/urea aqueous solution. The results from DSC and (13)C NMR indicated that LiOH/urea and NaOH/urea aqueous solutions as non-derivatizing solvents broke the intra- and inter-molecular hydrogen bonding of cellulose and prevented the approach toward each other of the cellulose molecules, leading to the good dispersion of cellulose to form an actual solution.     

Phenol‐urea‐formaldehyde cocondensed resol resins: Their synthesis,curing kinetics,and network properties

Several phenol‐urea‐formaldehyde (PUF) cocondensed resol resins were synthesized by different procedures. The curing kinetics and network properties of these PUF resins were examined by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). A kinetic study indicated that the activation energy values of PUF resins are generally higher than those of phenol‐formaldehyde (PF) resins during curing processes, but the curing rates of PUF resins are faster than those of PF resins. The pH values of PUF systems have a significant influence on the rate constants, although they affect the activation energy very slightly. Moreover, the dependence of activation energy on the conversion showed that there are more individual reactions with different activation energies occurring during the curing processes in PUF resins than in PF resins. The decomposition of methylene ether bridges to form methylene bridges probably occurs at high temperature in PUF resins. DMTA data indicated that the network rigidity of PUF resins is slightly lower than that of PF resin. The gel point and T_{tan δ2} transition measured by DMTA were consistent with the kinetic results obtained from the DSC data, but they were also related to the physical and mechanical properties of the network, especially with regard to the T_{tan δ2} transition. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1929–1938, 2003     

Crown ether molecular complexes with urea and thiourea

Crystalline complexes of urea and thiourea with crown ethers, have been prepared, viz., 18-crown-6 (18C6), benzo-18-crown-6 (B18C6), dibenzo-18-crown-6 (DB18C6), dicyclohexano-18-crown-6 (DC 18C6) and dibenzo-24-crown-8 (DB24C8). While the complexes of the large ring size crown ether, DB24C8, have high ether to (thio)urea ratios, the stoichiometry of the others lies between one molecule of crown ether and from one to six molecules of (thio)urea. An IR spectral study of the urea and thiourea complexes showed that the behavior of thiourea in these complexes is clearly different from that of urea, indicating the role of sulphur in the interaction of thiourea with crown ethers. The urea and thiourea complexes were classified according to their stoichiometries and their IR spectral behavior into three classes for which credible structures were proposed.     

缓释尿素中硝化抑制剂DMPP的气相色谱法测定

建立了一种检测缓释尿素中吡唑类硝化抑制剂DMPP的气相色谱法。DMPP在尿素水溶液中可定量转化为DMP,从5种有机溶剂中选择氯仿作为DMP的萃取剂,并采用加入KCl盐析的方法将萃取率从96.1%提高到99.5%。本文采用吡啶作为内标物,通过DB-1701气相色谱柱,氢火焰离子化检测器(FID)定量检测氯仿溶液萃取相中的DMP。萃取率为98.8%~100.4%;添加回收率为98.1%~99.5%;RSD为0.84%~1.6%。应用本法测定自制缓释尿素中DMPP质量分数为0.44%。     

公共场所空气中甲醛的测定——酚试剂分光光度法

采用酚试剂分光光度法对室内空气环境中甲醛含量进行了分析。研究表明,酚试剂分光光度法具简便、易控制、迅速、成本低等优点,在普通室内检测时应优先选用。     

Phase diagrams of urea inclusion compounds

The stearic acid-urea binary system exhibits an unusual phase diagram, which, on the one hand, indicates an incongruently melting inclusion compound and on the other hand a miscibility gap in the liquid phases. The peritectic point lies near the melting point of urea and the unstable congruent melting point of the inclusion compound coincides with the melting point of urea. In addition to the processing of the phase diagram, the pure inclusion compound was prepared and its DSC curve, FTIR spectrum and X-ray diffractogram were recorded.     

尿素包合法分离蚕蛹油中多不饱和脂肪酸

蚕蛹是缫丝副产品,我国每年副产近20万吨干蛹[1].蚕蛹中油脂含量相当丰富,约占蚕蛹干基的25%～29%,且油脂总量的71.0%为不饱和脂肪酸,这些不饱和脂肪酸在人体内可合成二十碳五烯酸及二十二碳六烯酸,与鱼油中的EPA,DHA具有相似的抗衰老、健脑益智的功能,能维持正常的肾脏功能,治腰背疼痛、肌肉无力,预防动脉硬化、血脂升高等血栓疾病[2].     

尿素作为添加剂低温制备高活性的TiO2光催化剂

以钛酸丁酯为原料,尿素作为添加剂,在酸性水溶液中室温制备了稳定透明的TiO2水溶胶。经过300℃低温焙烧2 h,得到了由锐钛矿和金红石组成的TiO2混晶。用XRD、FT-IR对催化剂进行了表征。以甲基橙为降解对象研究了TiO2的光催化活性,实验结果显示所制备的TiO2具有比Degussa P25更高的催化活性,15m in后的降解率达到了78%(P25,58%)。考察了尿素添加量以及焙烧温度对TiO2催化性能的影响,当尿素与钛酸丁酯物质的量之比为3∶1,300℃下焙烧2 h为较适宜的催化剂制备条件。初步探讨了尿素作为添加剂在低温制备高活性TiO2过程中的作用。     

Adenine-based urea receptors in fluorescent recognition of iodide

Adenine-based receptors 1 and 2 are designed and synthesized for selective sensing of iodide over the other halides and carboxylate anions. Both the receptors 1 and 2 use the urea motif for binding carboxylates and halides. Emissions of the naphthalene and the anthracene in 1 and 2, respectively, are monitored in CHCl₃ in detecting the anions. While carboxylates, fluoride, chloride, and bromide increase the emissions of naphthalene and anthracene in both the receptors 1 and 2 during complexation, iodide quenches the emission. Such selective quenching allows iodide to be discriminated from other halides and carboxylate anions.     

手性(硫)脲衍生物在不对称有机催化反应中的应用

手性(硫)脲衍生物是各种亲核试剂对亚胺、醛、缺电子烯烃加成反应的非常有效的有机催化剂之一, 已成功应用于对映选择性催化Strecker反应、Michael加成反应、Mannich反应、Baylis-Hillman反应、Henry反应等一系列重要的有机合成反应. 手性(硫)脲衍生物具有催化活性高、对映选择性和功能基相容性好、易于制备和修饰、适用范围广等优点, 成为近年来研究较多的不对称反应有机催化剂. 对手性(硫)脲衍生物在有机催化不对称合成中的应用研究进展进行了评述.