Mechanical and dynamic viscoelastic properties of hydroxyapatite reinforced poly(ε-caprolactone)

Poly(ε-caprolactone)/hydroxyapatite (PCL/HA) composites as potential bone substitutes were prepared by melt-blending. The melting, crystallization and glass transition temperatures deduced from differential scanning calorimetery and dynamic mechanical thermal analysis (DMTA) were all changed by the addition of HA, suggesting an interaction at the interface of these two phases. Quasi-static mechanical testing shows that the yield strength and Young's modulus of PCL were increased by the addition of the reinforcement filler, HA. Dynamic viscoelastic properties were investigated using DMTA and an advanced rheometric expansion system. The results show that both the storage modulus and viscous modulus are enhanced by HA, and the PCL composite melts still behave like pseudo-plastic liquid.     

Electrospun poly(ε‐caprolactone)‐based composites using synthesized β‐tricalcium phosphate

Non‐woven hybrid membranes based on poly(ε‐caprolactone) (PCL) and as‐synthesized β‐tricalcium phosphate (β‐TCP) were obtained by the electrospinning technique. A wide range of composition was investigated, the filler content spanning between 2 and 60 wt%. The synthesis of the β‐TCP powder was accomplished by titration of calcium hydroxide with phosphoric acid followed by calcination of the resulting precipitate at 1100°C. The as‐dried calcium phosphate was characterized by Inductive Coupled Plasma (AES‐ICP), thermal analysis (TG‐DTA), Fourier Transform Infrared Spectroscopy (FT‐IR), Scanning Electron Microscopy (SEM), and high temperature X‐ray diffraction analysis (HT‐XRD). The specific surface area (SSA) was evaluated by N₂ adsorption. Microstructure of PCL/TCP membranes was investigated by SEM, energy dispersion spectroscopy (EDS), XRD analysis, and SSA measurements. The average fiber diameter ranged between 1 and 2 µm, the porosity was 80–90%, and the SSA 16 m²/g. Mechanical properties were determined by uniaxial tensile test. A remarkable enhancement of the tensile modulus was observed for composites containing up to 4 wt% β‐TCP. The ultimate tensile strength ranged between 2 and 3 MPa for samples loaded up to 8 wt%. For most of the samples, the elongation at break was in the range 100–150%. Copyright © 2010 John Wiley & Sons, Ltd.     

带环氧基团纳米二氧化硅改性酚醛树脂的合成及热性能

以苯酚、甲醛、带环氧基团纳米二氧化硅(RNS-E)为原料,采用原位聚合法合成了RNS-E改性酚醛树脂.利用红外光谱(FT-IR)对其结构进行了分析,并利用热重分析(TGA)对其热性能进行了研究.结果表明,改性后的酚醛树脂热稳定性得到提高,当RNS-E的加入量为4%时(质量分数),失重10%时的热分解温度(t10%)较酚醛树脂的提高了15℃,1 000℃下残炭率较酚醛树脂提高了7%.     

Conformational transitions of poly(β-benzyl L-aspartate)

Conditions that affect the conformation of poly(β-benzyl L-aspartate) in films have been studied. A slow transition from the left-handed to the right-handed α-helical form is observed under certain conditions in half-dried film cast from chloroform solutions and after exposure of amorphous films of the left-handed β-helical form to chloroform vapor. This transition is caused by adsorption of moisture. Thermal transitions of these films were examined by differential scanning calorimetry and infrared spectroscopy. The right-handed α-helices change to left-handed ω-helices around 140°C, and sharp exothermic peak is observed in this region for some films.     

Supramolecular structure investigation of poly(γ-benzyl, α-l-glutamate)-benzyl alcohol system by static light scattering

The cholesteric mesophase of the PBLG-BA system in concentrated solutions and in the gel phase has been investigated by static laser light scattering. The observed ‘distortion’ of the patterns in terms of their dependence on the azimuthal angle was studied. Effect of form-optical rotation on the pattern is discussed. The manner of distortion in the H_v pattern determines the sense of cholesteric twisting. The observed scattering patterns are analogous to those obtained by previous investigators in other solvents. Quantitative measurements of the intensity as a function of scattering vector provide information on the sense and pitch of the cholesteric twisting, as a function of temperature and concentration. Optical microscopy studies reveal onset and build-up of the cholesteric structure. Optical rotation and differential scanning calorimetry (DSC) studies support the conclusions obtained from light-scattering experiments.     

Viscoelastic properties of poly(ε‐caprolactone) – hydroxyapatite micro‐ and nano‐composites

Various composites have been proposed in the literature for the fabrication of bioscaffolds for bone tissue engineering. These materials include poly(ε‐caprolactone) (PCL) with hydroxyapatite (HA). Since the biomaterial acts as the medium that transfers mechanical signals from the body to the cells, the fundamental properties of the biomaterials should be characterized. Furthermore, in order to control the processing of these materials into scaffolds, the characterization of the fundamental properties is also necessary. In this study, the physical, thermal, mechanical, and viscoelastic properties of the PCL‐HA micro‐ and nano‐composites were characterized. Although the addition of filler particles increased the compressive modulus by up to 450%, the thermal and viscoelastic properties were unaffected. Furthermore, although the presence of water plasticized the polymer, the viscoelastic behavior was only minimally affected. Testing the composites under various conditions showed that the addition of HA can strengthen PCL without changing its viscoelastic response. The results found in this study can be used to further understand and approximate the time‐dependent behavior of scaffolds for bone tissue engineering. Copyright © 2012 John Wiley & Sons, Ltd.     

Crystallinity and conformational changes in poly(β-benzyl L-aspartate)

The crystallinity of poly(β-benzyl L -aspartate) is highly variable, in a series of specimens prepared under various conditions: films cast from chloroform solutions at various evaporation rates, films cast comparatively slowly from chloroform–trifluoroacetic acid solutions, films prepared from dichloroacetic acid solution by treatment with ethyl alcohol, precipitates formed from trifluoroacetic acid solution by addition of ether. Film cast slowly from chloroform is in the highly crystalline ω form. In contrast, the conformation of the benzene rings in the ω helix obtained from the α helix by heating is distorted to some extent in comparison with the structure of the highly crystalline ω form. Crystallization and conformational changes from the α to the ω form, and from the ω to the β form upon heating, are correlated with the dispositions of the side chains, the packing of the benzene rings, and the motion of the side chains. The main chain of the α helix is distorted into the ω form when its side chains are in a favorable conformation. The α helix is stable in the disordered conformation, and it is distorted to some extent at high temperature.     

Crystallization behavior of poly(ε‐caprolactone)/multiwalled carbon nanotube composites

Differential scanning calorimetry (DSC), polarized optical microscopy, and X‐ray diffraction methods were used to investigate the isothermal crystallization behavior and crystalline structure of poly(?‐caprolactone) (PCL)/multiwalled carbon nanotube (MWNT) composites. PCL/MWNT composites were prepared via the mixing of a PCL polymer solution with carboxylic groups containing multiwalled carbon nanotubes (c‐MWNTs). Both Raman and Fourier transform infrared spectra indicated that carboxylic acid groups formed at both ends and on the sidewalls of the MWNTs. A transmission electron microscopy micrograph showed that c‐MWNTs were well separated and uniformly distributed in the PCL matrix. DSC isothermal results revealed that introducing c‐MWNTs into the PCL structure caused strongly heterogeneous nucleation induced by a change in the crystal growth process. The activation energy of PCL drastically decreased with the presence of 0.25 wt % c‐MWNT in PCL/c‐MWNT composites and then increased with increasing MWNT content. The result indicated that the addition of c‐MWNT to PCL induced heterogeneous nucleation (lower total activation energy) at a lower c‐MWNT content and then reduced the transportation ability of polymer chains during crystallization processes at a higher MWNT content (higher total activation energy). A correlation between the crystallization kinetics, melting behavior, and crystalline structure of PCL/c‐MWNT composites was also discussed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 598–606, 2006     

Molecular composites made of ionic poly(p‐phenylene terephthalamide) and poly(4‐vinylpyridine): Relaxation behavior

Molecular composites were prepared from several types of ionically modified, poly(p‐phenylene terephthalamide) (PPTA) dispersed in a poly(4‐vinylpyridine) matrix. Optical clarity tests indicated that the component polymers of the composite were miscible, at least at low concentrations of the rodlike reinforcement. In composites containing ionic PPTA, where ionic sulfonate groups were attached as side groups either to PPTA chains or to PPTA anion chains, the glass‐transition temperature (T_g) was increased by l0 °C or more, at 5 wt % reinforcement. At concentrations of 10–15 wt % of the ionic polymer, T_g values leveled off or decreased slightly. This suggested that some aggregation of the rigid‐rod molecules occurred. In composites containing ionic PPTA, where the ionic sulfonate groups were directly attached to the phenylene rings of PPTA chains, not only was T_g shifted significantly to higher temperatures, but the rubbery plateau modulus retained high values up to temperatures of 250 °C or above. Observed effects were considered to be the result of strong ionic interactions between the ionic reinforcement polymer and the polar matrix polymer. The possible effects of the counterion on T_g and the storage modulus are discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1110–1117, 2002     

Improved mechanical properties of epoxy composites reinforced with surface‐treated UHMWPE fibers

The surface treatment of ultra‐high molecular weight polyethylene fiber using potassium permanganate and the mechanical properties of its epoxy composites were studied. After treatment, many changes were happened in the fiber surface: more O‐containing groups (―OH, ―C═O, and ―C―O groups), drastically decreased contact angles with water and ethylene glycol, slightly increased melting point and crystallinity, and formed cracks. Different contents (0.1–0.5 wt%) ultra‐high molecular weight polyethylene fibers/epoxy composites were prepared. The results indicated that the surface treatment decreased the tensile strength of epoxy composites, but increased the bending strength. When the fiber content was 0.3 wt%, the above properties reached the maximum. At the same fiber content, the interlaminar shear strength of the composites was increased by 26.6% up to the as‐received fiber composites. Dynamic mechanical analysis of the composites suggested the storage modulus and tanδ were decreased due to the surface treatment. Fractured surface analysis confirmed that the potassium permanganate treatment was effective in improving the interface interaction.     

Preparation and cryogenic mechanical properties of epoxy resins modified by poly(ethersulfone)

A thermoplastic, poly(ethersulfone) (PES) was used to modify a bisphenol‐F based epoxy resin cured with an aromatic diamine. The initial mixtures before curing, prepared by melt mixing, were homogeneous. Scanning electron microscopy (SEM) micrographs of solvent‐etched fracture surfaces of the cured blends indicated that phase separation occurred after curing. The cryogenic mechanical behaviors of the epoxy resins were studied in terms of tensile properties and Charpy impact strength at cryogenic temperature (77 K) and compared to their corresponding behaviors at room temperature (RT). The addition of PES generally improved the tensile strength, elongation at break, and impact strength at both RT and 77 K except the RT tensile strength at 25 phr PES content. It was interesting to observe that and the maximum values of the tensile strength, elongation at break, and impact strength occurred at 20 phr PES content where a co‐continuous phase formed. Young's modulus decreased slightly with the increase of the PES content. Moreover, the tensile strength and Young's modulus at 77 K were higher than those at RT at the same composition, whereas the elongation at break and impact strength showed the opposite results. Finally, the differential scanning calorimetry analysis showed that the glass transition temperature (T_g) was enhanced by the addition of PES. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 612–624, 2008     

Growth stages in epitaxial crystallization of poly(γ-benzyl L-glutamate)

The electron microscope study of the isothermal epitaxial crystallization of PBLG on 001 cleavage surface of NaCl or KCl from 0.01% chloroform solution with various n-octane contents has shown that the epitaxial growth process could be divided in two stages. In the first stage a rapid growth of a lamellar layer 20–40 Å thick could be observed; the PBLG molecules in αhelix conformation are oriented along <110> substrate directions. The dimensions and perfectness of alignment of these lamellae along the <110> direction depends on the molecular weight of the PBLG. In the second stage of PBLG epitaxial crystallization the relatively slow thickening of some initial lamellae takes place and one can observe many types of secondary structures. With increasing thickness of the epitaxial structures and increasing molecular weight of the PBLG the degree of orientation in relation to <110> substrate direction diminishes. The two growth stages in PBLG epitaxial crystallization are related to different kinds of orienting and attracting forces of the alkali halide substrate.     

Preparation and properties of polyurethane networks based on α,ω-difunctional poly(hexafluoropropylene oxide)

Poly(hexafluoropropylene oxide), poly(HFPO), networks were prepared from functional polymers by end linking via urethane groups. The prepolymers were characterized by NMR spectroscopy and GPC. The networks were characterized by determination of the number of network chains from the shear modulus, and were snown to contain both trifunctional crosslinks and difunctional links. The properties of the networks were investigated by a range of techniques. Compared with fully-fluorinated networks formed via triazine cross-links, investigated previously, the urethane-linked networks were more readily prepared but were poorer elastomers, were less thermally stable, and were less resistant to swelling by common polar solvents. © 1995 John Wiley & Sons, Inc.     

A biocompatible composite based on poly(ε‐caprolactone fumarate) and hydroxyapatite

Fabrication of biodegradable composites applicable as hard tissue substitutes consisting of poly(ε‐caprolactone fumarate) (PCLF), methacrylic acid (MAA), and hydroxyapatite (HA) was investigated. PCLF macromers were synthesized by reaction of PCL diol with fumaryl chloride in the presence of propylene oxide and characterized by gel permeation chromatography, FTIR, and ¹H NMR spectroscopy. Composites were fabricated by incorporating HA as inorganic filler in PCLF matrix which followed by thermal curing of the composition using benzoyl peroxide and MAA as a free radical initiator and reactive diluent, respectively. Uniform distribution of the fine ceramic phase in the polymer matrix was elucidated by scanning electron microscopy. The effects of the initial macromer molecular weight and the filler volume fraction on mechanical properties and cytotoxicity of the composites were also examined. Significant enhancement in the mechanical properties was observed upon increasing HA content and/or initial PCLF molecular weight. The biocompatibility of the specimens was also improved with increasing ceramic phase. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation and properties of composites made from rice straw and poly(vinyl chloride) (PVC)

Rice straw was employed for the preparation of lignocellulosic‐poly(vinyl chloride) (PVC) composites. The effect of pretreatment of rice straw, concentration of PVC, pressure as well as pressing temperature on the mechanical properties and water absorption was studied. Also, the effect of lignin as coupling agent on the mechanical properties and water absorption of composite was studied. Composites of rice straw comprising both PVC and a coupling agent offer superior properties compared to those made from only rice straw and PVC. The extent of improvement in the mechanical properties and dimensional stability of composites depended not only on the pretreatment of rice straw, concentration of PVC and lignin but also on pressure and pressing temperature. Copyright © 2004 John Wiley & Sons, Ltd.     

Structural differences between two crystal modifications of poly(γ-benzyl L-glutamate)

X-ray diffraction patterns were obtained for as-cast and oriented films of poly(γ-benzyl L -glutamate) and a comparison was made of the molecular packing of the α-helices in forms B and C. Form B snowed Bragg reflections on the layer lines as well as on the equator. The spacings were explained by a monoclinic unit cell comprising two chains, with a = 29.0₆ Å, b = 13 2₀ Å, c = 27.2₇ Å α = γ = 90°. and β = 96°. The chains contained in this unit cell and consequently alternating in the crystal have opposite chain directions. Form C showed continuous scattering on the layer lines and reflections on the equator. This form, therefore, is a nematiclike paracrystal in which the packing of α-helices is periodic in the direction lateral to the chain axis (a = 14.8–115.2 Å, b = 14.3–14.8 Å, c = 27 Å, and γ = 118°–120°), but the relative levels of the chains along the chain axes are displaced. The formation of form C may be attributed to random placement of two chains with mutually opposite chain directions.     

Influences of poly(lactic acid)‐grafted carbon nanotube on thermal,mechanical, and electrical properties of poly(lactic acid)

Poly(lactic acid)‐grafted multiwalled carbon nanotubes (MWNT‐g‐PLA) were prepared by the direct melt‐polycondensation of L ‐lactic acid with carboxylic acid‐functionalized MWNT (MWNT‐COOH) and then mixed with a commercially available neat PLA to prepare PLA/MWNT‐g‐PLA nanocomposites. Morphological, thermal, mechanical, and electrical characteristics of PLA/MWNT‐g‐PLA nanocomposites were investigated as a function of the MWNT content and compared with those of the neat PLA, PLA/MWNT, and PLA/MWNT‐COOH nanocomposites. It was identified from FE‐SEM images that PLA/MWNT‐g‐PLA nanocomposites exhibit good dispersion of MWNT‐g‐PLA in the PLA matrix, while PLA/MWNT and PLA/MWNT‐COOH nanocomposites display MWNT aggregates. As a result, initial moduli and tensile strengths of PLA/MWNT‐g‐PLA composites are much higher than those of neat PLA, PLA/MWNT, and PLA/MWNT‐COOH, which stems from the efficient reinforcing effect of MWNT‐g‐PLA in the PLA matrix. In addition, the crystallization rate of PLA/MWNT‐g‐PLA nanocomposites is faster than those of neat PLA, PLA/MWNT, and PLA/MWNT‐COOH, since MWNT‐g‐PLA dispersed in the PLA matrix serves efficiently as a nucleating agent. It is interesting that, unlike PLA/MWNT nanocomposites, surface resistivities of PLA/MWNT‐g‐PLA nanocomposites did not change noticeably depending on the MWNT content, demonstrating that MWNTs in PLA/MWNT‐g‐PLA are wrapped with the PLA chains of MWNT‐g‐PLA. Copyright © 2008 John Wiley & Sons, Ltd.     

Structure and mechanical properties controlling of elastomer modified polypropylene by compounded β/α nucleating agents

Previous work showed that there was a synergistic effect of nucleating agent (NA) and elastomer in improving the fracture resistance of isotactic polypropylene (PP), relating to the formation of large amounts of β‐PP (β‐NA nucleated system) or the decrease of the spherulites diameters of α‐PP (α‐NA nucleated system). To find the direct relation between the synergistic efficiency of NA/elastomer and the microstructures of the materials, in this work, the ethylene‐propylene‐diene terpolymer (EPDM) modified PP blends with compounded NAs (β/α) were adopted and the changes of the microstructure and mechanical properties were investigated comparatively. The results showed that, with the adjustment of the mass fraction of compounded NAs, the microstructures of PP matrix including supermolecular structure and the relative fraction of β‐PP (K_β) change accordingly. Specifically, the K_β of β‐PP was successfully adjusted in the wide range of 0–78.9%. Consequently, the stiffness and the fracture resistance of the PP/EPDM blends were easily controlled in different degrees. It is believed that this work could provide a guide map for the design and preparation of certain polymer blends satisfying certain requirement. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Preparation,characterization and properties of fiber reinforced composites using silicon‐containing hybrid polymers

A novel glass fiber reinforced composite was prepared by using silicon‐containing hybrid polymers, poly(methylhydrogen‐diethynylsilyene) (PMES) and poly(phenylethynyl‐silyloxide‐phenylborane) (APABS), as matrix resins. The curing behavior and rheological properties of the matrix resins were investigated by differential scanning calorimetry (DSC) and rotational rheometer. The dynamic viscoelastic properties, mechanical properties, and microstructures of the composites were studied by dynamic mechanical analysis (DMA), universal testing machine (UTM), and scanning electron microscopy (SEM), respectively. The results show that the composite can be well cured between 200 and 300 °C through reactive groups like Si‐H, N‐H, and C≡C units, the possible thermosetting mechanism is also proposed. The composites exhibit excellent mechanical properties with bending strength reach up to 261 and 178 MPa before and after heat‐treating, respectively. SEM analysis clearly indicates that crack in the matrix, matrix/fiber interface debonding, and fiber pull out are predominate failure mechanism for the composites which are heat‐treated in different temperatures. All these obtained results can give theoretical guiding reference for their further applications. Copyright © 2016 John Wiley & Sons, Ltd.     

New nanohybrids of poly(ε‐caprolactone) and a modified Mg/Al hydrotalcite: Mechanical and thermal properties

Novel composites based on poly(ε‐caprolactone) (PCL) and an organically modified layer double hydroxide (LDH) obtained using the melt‐extrusion technique have been characterized through structural, thermal, and mechanical analyses. Although exfoliation has not been achieved and despite the very low content of filler (from 1 to 3% by weight), significant enhancements are obtained in the physical and mechanical properties of the composites with respect to neat PCL. As a consequence, LDHs can substitute other nanofillers, in particular, cationic clays for polymeric matrices. They can be modified by a large number of organic anions, generally more numerous than the cationic ones, and can be mixed in very simple ways with polymers. This makes such nanofillers suitable to obtain new hybrid materials for a series of applications, from active food packaging to intelligent materials for biomedical device, for example, controlled drug release. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 945–954, 2007