Tailoring of interface of polypropylene/polystyrene/carbon nanofibre composites by polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene

Mechanical and physical properties of polypropylene (PP)/polystyrene (PS) blend, PP/PS/polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) ternary blend and their composites with carbon nanofibers (CNF) were investigated. Composites of ternary blend exhibited superior properties compared to those of binary blends. Mechanical performance of nanocomposites was intimately related to their phase morphology. PP/PS/SEBS/0.1 wt% CNF hybrid composites exhibited excellent impact strength (Four-fold increase compared to PP/PS blend) and ductility (12-fold increase in elongation at break, with respect to PP/PS blend). Moreover, these composites displayed good tensile strength and modulus (15% increase in Young's modulus, compared to PP/PS/SEBS blend) and are suitable for various end-use applications including automobile applications. Although crystallinity of PP phase is decreased by the incorporation of CNF, thermal stability of the composites remained almost unaffected. Contact angle measurements revealed that ternary composites exhibited maximum hydrophobicity.     

Morphology, crystallization behavior and properties of impact-modified polypropylene copolymer with or without sodium benzoate as a nucleating agent

 The morphology, crystallization behavior, and properties of an impact-modified polypropylene (PP) copolymer with or without sodium benzoate were investigated. The contents of ethylene–propylene rubber (EPR) in the reactor-made PP copolymer is about 15 wt%. For comparison, blends of PP and EPR containing the same EPR composition were prepared by melt-mixing. Morphological studies by scanning probe microscopy indicated that the impact-modified copolymer consists of three different phases, i.e., polyethylene, PP, and EPR phases, which is considerably different from the morphology of the conventional PP/EPR blend of the corresponding composition. The impact-modified PP copolymer exhibited a higher crystallization rate in terms of the lower crystallization half-time and thus higher thermal and mechanical properties, such as impact strength and hardness, than the PP/EPR blend did. The addition of sodium benzoate as a nucleating agent to the copolymer increased the crystallization rate and the mechanical properties. Received: 4 June 2001 Accepted: 31 October 2001     

Properties of immiscible and ethylene-butyl acrylate-glycidyl methacrylate terpolymer compatibilized poly (lactic acid) and polypropylene blends

Poly(lactic acid) (PLA) and polypropylene (PP) blends of various proportions were prepared by melt-compounding. The miscibility, phase morphology, thermal behavior, and mechanical and rheological properties of the blends were investigated. The blends were immiscible systems with two typical morphologies, spherical droplet and co-continuous, and could be obtained at various compositions. Complex viscosity, storage modulus and loss modulus depend on the PP content. Thermal degradation of all blends led to two weight losses, for PLA and PP. The incorporation of PP improved the thermal stability of the blend. The effect of compatibilizer (ethylene-butyl acrylate-glycidyl methacrylate terpolymer, EBA-GMA) on the morphology and mechanical properties of 70/30 w/w PLA/PP blends was investigated. The tensile strength of these blends reached a maximum for 2.5 wt% EBA-GMA, and impact strength increased with increasing EBA-GMA content, suggesting that EBA-GMA is an effective compatibilizer for PLA/PP blends.     

Preparation and properties of PP/PC/POE blends

In order to develop PP (polypropylene)‐based blends with balanced toughness and rigidity, the poly‐blends of PP/PC (polycarbonate)/POE (ethylene–octene copolymer) were prepared by applying styrene–ethylene–propylene–styrene (SEPS) as the macromolecular compatibilizer. The compatibilizing effect was studied in terms of the mechanical, morphologies and thermal properties, and the compatibilized PP‐based blends presented remarkable improvement in impact toughness and balanced tensile strength due to the formed special morphology structure. Additionally, by preparing the pre‐blend of PC/SEPS, the melt viscosity of the PP matrix can match that of the dispersed phase PC and POE, which led to a further improvement in the mechanical property of the blends. Copyright © 2009 John Wiley & Sons, Ltd.     

氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物及其马来酸酐接枝共聚物增韧聚对苯二甲酸乙醇酯共混材料的辐射效应

采用双螺杆熔融共混的方法制备了含三羟甲基丙烷三丙烯酸酯(TMPTA)的聚对苯二甲酸乙二酯/氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物（PET/SEBS）和聚对苯二甲酸乙二酯/马来酸酐接枝氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物（PET/SEBS-g-MAH）共混材料,并在Co-60源中对其进行辐照。 通过对共混材料的力学性能、相态结构测和凝胶含量分析,对比研究了辐射对以上2种共混材料结构及性能的影响。 扫描电子显镜观察和凝胶含量分析结果表明,在适量TMPTA存在时,辐射有效地改善了PET/SEBS体系的相容性。 冲击强度的变化证实了这种增容效应,当SEBS的质量分数为20%、TMPTA质量分数为1%,经50 kGy辐照后,冲击强度达到17.3 kJ/m2。 当在SEBS分子链上引入马来酸酐官能团,辐照后,体系的相态结构变化并不明显,冲击强度最大值仅为11.5 kJ/m2,明显低于不含马来酸酐官能团的体系。     

The effect of various compatibilizers on thermal,mechanical, and morphological properties of polystyrene/polypropylene blends

The effects of various compatibilizers on thermal, mechanical and morphological properties of 50/50 polypropylene/polystyrene blends were investigated. Various compatibilizers, polystyrene-(ethylene/butylenes/ styrene) (SEBS), ethylene vinyl acetate (EVA), polystyrene-butylene rubber (SBR) and blend of compatibilizers SEBS/PP-g-MAH, EVA/PP-g-MAH, and SBR/PP-g-MAH were used. Differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray scattering, scanning electron microscopy, microhardness, and Izod impact strength were adopted. It was found that the influence of various compatibilizers was appeared on all the properties studied. The properties of the blends compatibilized with SEBS, EVA, and SBR are very distinct from those of blends compatibilized with blend of compatibilizers. Results show that compatibilized blends with the blend of compatibilizers EVA/PP-g-MAH, SBR/PP-g-MAH, and SEBS/PP-g-MAH or SBR were relatively more stable than the uncompatibilized blend and blend compatibilized with SEBS or EVA. The compatibilizer does not only reduce the interfacial tension or increase the phase interfacial adhesion between the immiscible polymers, but greatly affects the degree of crystallinity of blends.

     

含二烯丙基双酚A醚相容剂对HDPE/PC共混体系的影响

用低密度聚乙烯接枝二烯丙基双酚Ａ醚（ＬＤＰＥ ｇ ＤＢＡＥ）作为高密度聚乙烯／聚碳酸酯（ＨＤＰＥ／ＰＣ）共混体系的增容剂,研究了其对ＨＤＰＥ／ＰＣ共混体系的影响．通过共混物形态观察、热力学性能测试和结晶性分析,发现ＬＤＰＥ ｇ ＤＢＡＥ对ＨＤＰＥ／ＰＣ共混体系有良好的增容效果．并发现了增容剂在共混物中的最佳用量为１０ｐｈｒ,提高增容剂的接枝率更有利于改善共混物的性能     

Compatibilizing effect of functionalized polystyrene blends: a study of morphology,thermal, and mechanical properties

Polystyrene (PS), being an amorphous polymer is immiscible with other polymers. To engender miscible blends, PS has been functionalized with an active amino‐functional group on the molecular chains of PS to yield amino‐substituted polystyrene (APS), which serves as a reactive compatibilizer. The compatibilization effect of amino functionalized polystyrene on the rubber toughening was explored and results were compared in terms of morphology, thermal, and mechanical properties of PS/SEBS‐g‐MA versus APS/SEBS‐g‐MA blends. In addition, the effect of rubber content on the blend morphology and mechanical properties were investigated. An appreciable change in the thermal stability of APS blends in comparison with PS blend has been probed. A marked correlation has been observed between phase morphology and thermal stability. Use of APS produced the compatibilized blends which render improved blend morphology, enhanced thermal and mechanical properties. Optimal thermal, morphological and mechanical profiles were depicted by 20‐wt% APS blend. Copyright © 2008 John Wiley & Sons, Ltd.     

Structural and mechanical behavior of polypropylene/ maleated styrene‐(ethylene‐co‐butylene)‐styrene/sisal fiber composites prepared by injection molding

Hybrid composites consisting of isotactic poly(propylene) (PP), sisal fiber (SF), and maleic anhydride grafted styrene‐(ethylene‐co‐butylene)‐styrene copolymer (MA‐SEBS) were prepared by melt compounding, followed by injection molding. The melt‐compounding torque behavior, thermal properties, morphology, crystal structure, and mechanical behavior of the PP/MA‐SEBS/SF composites were systematically investigated. The torque test, thermogravimetric analysis, differential scanning calorimetric, and scanning electron microscopic results all indicated that MA‐SEBS was an effective compatibilizer for the PP/SF composites, and there was a synergism between MA‐SEBS and PP/SF in the thermal stability of the PP/MA‐SEBS/SF composites. Wide‐angle X‐ray diffraction analysis indicated that the α form and β form of the PP crystals coexisted in the PP/MA‐SEBS/SF composites. With the incorporation of MA‐SEBS, the relative amount of β‐form PP crystals decreased significantly. Mechanical tests showed that the tensile strength and impact toughness of the PP/SF composites were generally improved by the incorporation of MA‐SEBS. The instrumented drop‐weight dart‐impact test was also used to examine the impact‐fracture behavior of these composites. The results revealed that the maximum impact force (F_max), impact‐fracture energy (E_T), total impact duration (t_r), crack‐initiation time (t_init), and crack‐propagation time (t_prop) of the composites all tended to increase with an increasing MA‐SEBS content. From these results, the incorporation of MA‐SEBS into PP/SF composites can retard both the crack initiation and propagation phases of the impact‐fracture process. These prolonged the crack initiation and propagation time and increased the energy consumption during impact fracture, thereby leading to toughening of PP/MA‐SEBS/SF composites. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1214–1222, 2002     

Combined effect of compatibilizer and carbon nanotubes on the morphology and electrical conductivity of PP/PS blend

In this work, maleic anhydride grafted styrene–ethylene–butadiene–styrene copolymer (SEBS‐g‐MA) and carbon nanotubes (CNTs) were introduced into the immiscible polypropylene/polystyrene (PP/PS) blend. Among the three polymer components, SEBS‐g‐MA has the strongest affinity to CNTs; thus, it exhibits dual effects to adjust the phase morphology of the blends and the dispersion state of CNTs in the blends. The experimental observations obtained from morphology characterizations using scanning electron microscope and transmission electron microscope confirm the selective localization of CNTs at the interface of the immiscible PP/PS blend. As a consequence, largely decreased percolation threshold is achieved when most of CNTs are selectively localized at the interface region between PP and PS. Copyright © 2014 John Wiley & Sons, Ltd.     

Influence of extender oil composition on flowing property,thermal stability,and morphology of styrene‐b‐ethylene‐co‐butylene‐b‐styrene copolymer/polypropylene/oil blends

In this study, a series of styrene‐b‐ethylene‐co‐butylene‐b‐styrene copolymer (SEBS)/polypropylene (PP)/oil blends with different kinds of oil composition was developed through melt blending. The effect of oil with different composition and properties on its phase equilibrium and “redistribution” in multiphasic SEBS elastomer was systematically studied for the first time. Moreover, an integral influencing mechanism of oil composition on the structure and properties of SEBS/PP/oil blends was also put forward. The mineral oil was mainly distributed in ethylene/butylene (EB)/PP phase, which greatly enhanced the processing flowability of SEBS/PP/oil blends. With increasing oil C_N content, a redistribution of oil appeared and excess naphthenic oil (NO) entered the interphase of soft and hard phases. The dynamic mechanical thermal analysis (DMTA) analysis indicated that the polystyrene (PS) phase was plasticized, which also helped to improve the processing fluidity of blends. However, the plasticizing of physical cross‐linking point PS resulted in a decrease in mechanical strength and thermal stability. Small‐angle X‐ray scattering (SAXS) and transmission electron microscope (TEM) results showed that PS phase (45 nm to 55 nm) cylindrically distributed in EB/PP/oil matrix, the excess NO in the interphase enlarged the distance between PS phase and widen the escape channel for oil migration. At over 45% oil C_N content, the electron density difference between soft and hard phases reduced to the minimum, same as T_gPS, indicating a deeper plasticizing effect. The PS phase swelled and exhibited elastic behavior; thus, the force could be uniformly transferred between two phases. Importantly, a recover in strength and thermal stability was observed in O‐5 blend. This work significantly filled the gap of studies in oil‐extended thermoplastic elastomers (TPEs), exhibiting great theoretical guiding significance and application value.     

PET/R‐PP/PC blends by two‐stage reactive extrusion: effect of polypropylene reactively functionalized with an oxazoline group on morphology and mechanical properties

A series of PET/R‐PP/PC blends was studied in a chemical modification involving reactive extrusion with a ricinyl‐2‐oxazoline maleinate. The interfacial reaction between blend components were studied by the differential scanning calorimetry (DSC) and the scanning electron microscopy (SEM). The static tensile and flexural properties, and impact resistance response of the blends were tested. The phase morphology of the blends was of interpenetrating network (IPN) type according to SEM results. The blends offer excellent mechanical properties and improved impact strength as an effect of chemical reactions on reactive extrusion, even if PET waste and low PC contents (below 20%) have been used.     

PBT/POE-g-MAH/PP共混体系的相态结构与性能

采用马来酸酐接枝乙烯-辛烯共聚物弹性体(POE-g-MAH)与聚丙烯(PP)在双螺杆挤出机上进行熔融共混,制备了3种新型增韧改性剂.研究了增韧改性剂的种类及其用量对共混物的力学性能、相形态结构、熔融与结晶行为的影响.力学性能测试表明,POE-g-MAH与适量PP并用具有显著的协同增韧作用,当POE-g-MAH与PP的配比为70/30时,所得增韧改性剂(POEg2)具有最佳的增韧效果.当POEg2含量达到15%时,共混物的缺口冲击强度(Is)从纯PBT的7.5 kJ/m2提高到51.2 kJ/m2,与15%的纯POE-g-MAH弹性体增韧PBT具有相近的缺口冲击强度值.同时,共混物的拉伸强度(σb)损失最小.采用AFM和SEM观察发现,新型增韧改性剂作为分散相具有软壳-硬核结构.DSC测试表明,随增韧改性剂中PP含量增加到一定值时,壳-核结构中软壳层出现不完整现象,导致界面作用力减小,共混物的Is和σb都出现明显下降.     

Poly(lactic acid)/poly(butylene succinate)/calcium sulfate whiskers biodegradable blends prepared by vane extruder: Analysis of mechanical properties,morphology, and crystallization behavior

Ternary blends of PLA/PBS/CSW with different weight fractions were prepared using a vane extruder. The mechanical properties, morphology, crystallization behavior and thermal stability of the blends were investigated. For the PLA/CSW blend, the tensile strength decreased, the flexural strength and modulus increased compared with pure PLA. For PBS, the addition of CSW had little influence on the mechanical properties. For the ternary blends PLA/PBS/CSW, the tensile strength, flexural strength and modulus decreased compared with pure PLA, while the elongation at break and the impact strength increased significantly. The brittle-ductile transition of the blends took place when the PBS weight fraction reaching 30 wt%. As a soft component in the blends, PBS was beneficial to improve the tensile ductility and the toughness of PLA. SEM measurements reveal that PLA/PBS/CSW blends were immiscible. When the weight fraction of PBS was 50 wt%, significant phase separation was observed, and CSW had preferential location in the PBS phase of the blend. DSC measurement and POM observation reveal that CSW had a heterogeneous nucleation effect on PLA and PBS matrix. The addition of PBS improved the crystallization of PLA and the thermal resistance of the PLA/PBS/CSW blends significantly.     

间规聚苯乙烯/等规聚丙烯/间规聚苯乙烯-b-聚(1-丁烯)共混体系相容性

间规聚苯乙烯(sPS)的改性主要是对其增韧改性,提高其力学性能.sPS的化学改性已有较多文献报道[1,2].     

多单体接枝聚丙烯对PBT/PP共混体系的形态结构及力学性能影响研究

研究了甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)多单体熔融接枝聚丙烯 (PP g (GMA co St) )对聚对苯二甲酸丁二酯 (PBT) 聚丙烯 (PP)共混物的形态结构和力学性能的影响 .利用双螺杆挤出机对PBT PP合金进行共混挤出 ,使用DSC、FT IR和SEM、TEM等手段对共混物进行了分析和相形态观察 ,并测试了力学性能 .实验证明 ,熔融共混过程中PP g (GMA co St)的环氧基团可以与PBT的端羧基发生化学反应 ,就地生成了PBT g PP共聚物 ,该共聚物可对PBT PP合金起到良好的增容剂作用 ,使共混物的相区尺寸显著减小 ,共混物的拉伸强度和冲击强度等力学性能同时得到明显改善 ,达到了弹性体系或小分子增容所难以达到的力学性能平衡的效果 .此外 ,TEM的研究还在PBT PP g (GMA co St)共混物中发现了特殊的微相分离结构     

Rheology,morphology and tensile properties of thermotropic liquid crystalline polymer/polypropylene in‐situ composites

Blends of various grades of polypropylene (PP) with a thermotropic liquid crystalline polymer (TLCP), namely a copolymer of p‐benzoic acid and ethylene terephthalate (60/40 mole ratio) were prepared as extruded films. A thermoplastic elastomer styrene (ethylene‐butylene) styrene (SEBS) was used as a compatibilizer. Melt viscosities of all specimens were measured using a plate‐and‐plate rheometer with oscillating mode in the shear rate region of 1 ‐ 200 rad/s. Addition of SEBS compatibilizer resulted in an increase of the blend viscosity. Observation of the blend morphology revealed an improvement of TLCP dispersion. The TLCP fiber aspect ratio (length to diameter) in the extruded film also increased after addition of SEBS. As a result, the film modulus in extrusion direction was enhanced. The tensile strength of the film specimen was also increased due to an improvement of interfacial adhesion.     

Impact‐specific essential work of fracture of maleic anhydride‐compatibilized polypropylene/elastomer blends and their composites

Charpy drop‐weight‐impact and essential work of fracture (EWF) characteristics of maleic anhydride (MA)‐compatibilized styrene–ethylene butylene–styrene (SEBS)/polypropylene (PP) blends and their composites reinforced with short glass fibers (SGFs) were investigated. MA was grafted to either SEBS copolymer (SEBS‐g‐MA) or PP (PP‐g‐MA). The mPP blend was prepared by the compounding of 95% PP and 5% PP‐g‐MA. Drop‐weight‐impact results revealed that the mPP specimen had an extremely low impact strength. The incorporation of SEBS or SEBS‐g‐MA elastomers into mPP improved its impact strength dramatically. Similarly, the addition of SEBS was beneficial for enhancing the impact strength of the SGF/SEBS/mPP and SGF/SEBS‐g‐MA/mPP hybrids. A scanning electron microscopy examination of the fractured surfaces of impact specimens revealed that the glass‐fiber surfaces of the SGF/SEBS/mPP and SGF/SEBS‐g‐MA/mPP hybrids were sheathed completely with deformed matrix material. This was due to strong interfacial bonding between the phase components of the hybrids associated with the MA addition. Impact EWF tests were carried out on single‐edge‐notched‐bending specimens at 3 m s^?1. The results showed that pure PP, mPP, and the composites only exhibited specific essential work. The nonessential work was absent in these specimens under a high‐impact‐rate loading condition. The addition of SEBS or SEBS‐g‐MA elastomer to mPP increased both the specific essential and nonessential work of fracture. This implied that elastomer particles contributed to the dissipation of energy at the fracture surface and in the outer plastic zone at a high impact speed of 3 m s^?1. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1881–1892, 2002     

TIME-DEPENDENT MORPHOLOGY OF POLYETHYLENE-POLYPROPYLENE BLENDS

The effect of time-temperature treatment on morphology of polyethylene-polypropylene (PE-PP) blends wasstudied to establish a relationship between thermal history, morphology and mechanical properties. Polypropylene (PP)homopolymers were used to blend with various polyethylenes (PE), including high density polyethylene (HDPE), lowdensity polyethylene (LDPE), linear low density polyethylene (LLDPE), and very and ultra low density polyethylene(VLDPE and ULDPE). The majority of the blends were prepared at a ratio of PE:PP = 80:20, while blends of PP and LLDPEwere prepared at various compositions. Thermal treatment was carried out at temperatures between the crystallizationtemperatures of PP and PEs to allow PP to crystallize first from the blends. On cooling further, PE crystallized too. A verydiffuse PP spherulite morphology in the PE matrix was formed in some partially miscible blends when PP was less than 20%by mass. Droplet-matrix structures were developed in other blends with either PP or PE as dispersed domains in a continuousmatrix, depending on the composition ratio. The scanning electron microscopy (SEM) images displayed a fibrillar structureof PP spherulite in the LLDPE-PP (80:20) and large droplets of PP in the HDPE-PP (80:20) blend, providing larger surfacearea and better bonding in the LLDPE-PP (80:20) blends. This explains why the blends with diffuse spherulite morphologyshowed greater improvement in tensile properties than droplet-matrix morphology blends after time-temperature treatment.     

Blends of polycarbonate and ethylene-1-octylene copolymer

The mechanical properties and morphology of polycarbonate/ethylene-1-octylene copolymer (PC/POE) binary blends and PC/POE/ionomer ternary blends were investigated. The tensile strength and elongation at break of the PC/POE blends decreased with increasing the POE content. The impact strength of the PC/POE blends showed less dependence on thickness than that of PC. And the low-temperature impact strength of PC was modified effectively by addition of POE. The morphology of the PC/POE blends was observed by scanning electron microscope. The PC/POE weight ratio had a great effect on the morphology of the PC/POE blends. For the PC/POE (80/20)/ionomer ternary blends, low content (0.25 and 0.5 phr) of ionomer could increase the tensile properties of PC/POE (80/20) blend and had little effect on the impact strength. And 0.5 phr ionomer made the dispersed domain distribute more uniformly and finely than the blend without it. But with high content of ionomer, the degradation of PC made the mechanical properties of the blends deteriorate. Blending PC and ionomer proved the degradation of PC, and the molecular weight decreased with increasing the ionomer content.