Terpolymerization of carbon monoxide, ethylene and styrene in the presence of supported palladium catalyst

Terpolymers of carbon monoxide with ethylene and styrene are synthesized in the presence of supported palladium catalyst in toluene and heptane medium for the first time. The terpolymerization rate exceeds the rate of carbon monoxide and ethylene copolymerization. The maximum terpolymer yield amounts 7.9 g per g of supported catalyst per hour or 321 g per g of palladium per hour. The influence of reaction temperature, pressure, 1.4-benzoquinone amount and co-monomers mole ratio on the yield and the composition of terpolymer have been studied. The NMR ¹³C data obtained testify to a distribution of ethylene and styrene units in terpolymer with the predominance of short blocks at equal contents of comonomer units.     

Synthesis of poly(carbon monoxide-co-ethylene-co-hexene) with supported palladium catalysts

The effect of conditions of carbon monoxide terpolymerization with ethylene and 1-hexene on the yield and composition of the terpolymer is investigated. The reaction is first carried out in toluene with the use of a supported palladium catalyst at different molar ratios of the olefins in the reaction solution. An increase in the hexene-to-ethylene molar ratio from 0.2 to 2.9 is accompanied by a decrease in the yield of the terpolymer by a factor of 2.8 and by a small increase in the molar fraction of hexene units in the terpolymer from 0.02 to 0.005?C0.06. The dependence of the amount of hexene units in the terpolymer on the olefin ratio differs from that obtained earlier in terpolymerization with propylene.     

Synthesis and characterization of high molecular weight poly(1,2-propylene carbonate-<Emphasis Type="Italic">co</Emphasis>-1,2-cyclohexylene carbonate) using zinc complex catalyst

Using supported multi-component zinc dicarboxylate catalyst,poly（1,2-propylene carbonate-co-1,2-cyclohexylene carbonate）（PPCHC） was successfully synthesized from carbon dioxide（CO₂） with propylene oxide（PO） and cyclohexene oxide（CHO）.The conversion of epoxides dramatically increased up to 89.7%（yield:384.2 g of polymer per g of Zn） with increasing reaction temperature from 60℃to 80℃.The optimized reaction temperature is 80℃.The chemical structure,the molecular weight,as well as thermal and mechanical properties of the resulting terpolymers were investigated extensively. When CHO feed content（mol%） is lower than 10%,the PPCHC terpolymers have number average molecular weight（M_n） ranging from 102×10³ to 202×10³ and molecular weight distribution（MWD） values ranging from 2.8 to 3.5.In contrast to poly（propylene carbonate）（PPC）,the introduction of small amount of CHO leads to increase in the glass transition temperature from 38.0℃to 42.6℃.Similarly,the mechanical strength of the synthesized terpolymer is greatly enhanced due to the incorporation of CHO.These improvements in mechanical and thermal properties are of importance for the practical application of PPC.     

氧化环己烯连续进料下二氧化碳-环氧丙烷-氧化环己烯三元共聚物的合成

由于氧化环己烯（CHO）与二氧化碳的共聚反应速度比其与环氧丙烷（PO）快,这种竞聚率的差异导致一锅法所得的二氧化碳-环氧丙烷-氧化环己烯三元共聚物的组成难以稳定控制。 为此本文在稀土三元催化剂下,采用氧化环己烯单体连续进料的方法合成了二氧化碳-环氧丙烷-氧化环己烯三元共聚物,催化效率可达575 g/(mol Zn h)。 三元共聚物的玻璃化转变温度随CHO含量升高而增大,当CHO的摩尔投料比从0.19增加到0.59时,玻璃化温度从44.3 ℃提高到70.1 ℃。 CHO连续进料合成的三元共聚物的组成与投料比基本相近,且连续进料法所合成的三元共聚物只有一个玻璃化转变温度,而普通的一锅法所得的三元共聚物通常存在两个玻璃化转变温度,因此连续进料法是制备组成稳定的二氧化碳-环氧丙烷-氧化环己烯三元共聚物的有效方法。     

Radiation induced terpolymerization of tetrafluoroethylene with propylene and n-butyl vinyl ether in bulk

Terpolymerization of tetrafluoroethylene (TFE) with propylene (P) and n-butyl vinyl ether (NBVE) induced by γ-rays at room temperature at dose rate 5 × 10⁵ rad/h and P/NBVE molar ratio from 49/1 to 10/40 was carried out. An alternating copolymerization between TFE and two α-olefins was found to take place in this system, so that 50 mole % of TFE containing terpolymer is always formed at various monomer compositions. The terpolymer composition can be explained successfully by the treatment by a complex mechanism. The complex reactivity ratios of r_I (TFE–complex) and r_II (TFE-NBVE complex) were calculated to be 0.5 and 0.6, respectively, assuming a complex mechanism. The polymerization rate and molecular weight increase with NBVE concentration in the monomer mixture. Colorless transparent rubber-like polymers were obtained at each monomer composition. The glass transition temperature sharply decreases with NBVE concentration in the terpolymer but the thermal and chemical resistances of the terpolymer slightly decrease. Considering these results together with the mechanical properties it has been concluded that the 45/48/7 terpolymer of TFE/P/NBVE molar ratio is good as a practical elastomer useful at relatively low temperatures.     

耐紫外光老化CO2共聚物的合成与性能

CO₂基塑料(PPC)是通过CO₂与环氧丙烷共聚所得的生物降解高分子,由于PPC的耐紫外老化性能较差,随紫外线的照射不仅PPC的相对分子质量快速下降,且其拉伸强度和断裂伸长率等力学性能也迅速降低,而农用地膜长期处于紫外线照射的环境中,因此亟待改善PPC的耐紫外老化性能。 本文设计合成了含紫外吸收基团的单体2-羟基-4(2,3-环氧丙氧基)二苯甲酮(HEB),与CO₂和环氧丙烷进行三元共聚制备了耐紫外光老化的CO₂共聚物(PPCH)。 在保证PPCH相对分子质量不低于5.0×10⁴的前提下,PPCH中HEB单元的摩尔分数最高可达0.32%,相应地其玻璃化转变温度(T_g)和起始热分解温度(T_d-5%)分别为26.7和216.9 ℃,拉伸强度达到30.97 MPa。 普通PPC经过240 h的紫外辐照后,其数均相对分子质量下降了67.8%,相应地其拉伸强度和断裂伸长率分别下降了10.1%和40.1%。 即使PPCH中的HEB摩尔分数仅为0.06%,经过240 h辐照后其数均相对分子质量仅下降了6.2%,相应地其拉伸强度和断裂伸长率也仅分别下降了1.7%和13.3%,证明PPCH具有较强的耐紫外老化性能,原因在于其主链含有HEB单元,对紫外光具有较好的吸收性能。 PPCH的紫外吸收性能随HEB单元在聚合物中含量的增加而增强,因此随着共聚物中引入的HEB单元含量增加,PPCH的相对分子质量和力学性能的保持率均得到了大幅度提高。 另一方面,对PPCH共聚物与相同二羟基二苯甲酮(BP)含量的PPC/BP共混物进行120 h的50 ℃热水萃取实验,PPCH显示出稳定的紫外光吸收性能,而PPC/BP共混物的紫外吸收性能随热水萃取时间的增长而快速下降,表明三元共聚反应能够有效解决普通共混物面临的小分子紫外吸收剂的外迁移问题。     

无配体Pd/LDH-F催化剂在Heck和Suzuki反应中的应用

 以氟离子插层的水滑石LDH-F为载体,用逐滴浸渍法制备了新型Pd/LDH-F催化剂,并用其催化溴代芳烃的Heck和Suzuki偶联反应. 用X射线衍射表征了催化剂的晶相,以等离子体发射光谱测定了溶剂中钯的流失量. 结果表明,对于Heck反应,在无配体存在和低钯用量(Pd/溴代芳烃摩尔比为0.001)的情况下, Pd/LDH-F的催化性能优于其它载体负载的Pd催化剂,显示出很高的催化活性和选择性. 在140 ℃和12 h的条件下, Pd/LDH-F催化溴苯与苯乙烯Heck反应产物的收率可达86％, 反应后催化剂经过分离,可循环使用四次其催化活性基本不变. 在DMF/水摩尔比为0.5的混合溶剂中,在室温和3 h 的条件下, Pd/LDH-F (Pd/溴代芳烃摩尔比为0.005)催化溴苯与苯基硼酸盐的Suzuki反应中,目标产物收率为99%.     

丙烯酸酯三元共聚物负载硫铂络合物的合成及催化性能

丁二醇二丙烯酸酯、丙烯酸甲酯、丙烯酸β-氯乙酯或丙烯酸ω-氯己酯进行三元共聚,合成了两类4种带ω-氯侧基的交联型聚丙烯酸酯.它们以乙硫醇硫醚化,再与氯亚铂酸钾反应,得到4种交联型聚丙烯酸酯负载的硫铂络合物.这些络合物对癸烯-1、十二烯-1、苯基烯丙醚、苯乙烯与三乙氧基硅烷的硅氢加成反应具有良好的催化活性.讨论了温度、催化剂用量对催化性能的影响及催化剂的重复使用情况.     

丙烷甲醇制烯烃共反应的热力学和动力学分析

通过计算和实验研究相结合的方法研究丙烷甲醇共进料制烯烃反应热力学及动力学过程.热力学过程采用Gibbs最小自由能法模拟丙烷甲醇制烯烃反应体系的平衡组成,同时结合响应面分析法建立了温度、压力、丙烷甲醇进料摩尔比对产物中丙烯的摩尔分数的函数关系,通过回归方程分析最佳工艺范围.热力学分析了反应条件对平衡产物的影响,随着反应温度升高,平衡产物丙烯的质量分数先增高后降低;平衡产物中丙烯的质量分数随着丙烷甲醇进料中丙烷摩尔比增高而增高,但是实际的反应状态和催化剂也是相关的,因此研究了存在催化剂情况下,丙烷脱氢和丙烷甲醇共进料反应的活化能.反应活化能动力学实验表明,通过添加少量甲醇可以降低耦合过程中丙烷脱氢表观活化能.     

Copolymerization of ethylene and propylene catalyzed by magnesium chloride supported vanadium/titanium bimetallic Ziegler-Natta catalysts

Magnesium chloride supported vanadium/titanium bimetallic Ziegler-Natta catalysts with di-i-butyl phthalate as internal donor for copolymerization of ethylene and propylene were prepared.The effects of reaction temperature, ethylene/propylene molar ratio,aluminium/vanadium（Al/V）molar ratio and titanium/vanadium molar ratio on the catalytic activity were investigated.The molecular weight,molecular weight distribution,sequence composition and crystallinity of the products were measured by gel permeation chromatography,¹³C-NMR and differential scanning calorimetry analysis, respectively.In comparison to the vanadium and titanium catalysts,the bimetallic catalyst showed higher catalytic activity and better copolymerization performance.The obtained ethylene/propylene copolymers have high molecular weight （10⁵）,broad molecular weight distribution,high propylene content with random or short blocked sequence structures （r_Er_P=1.919）,low melting temperatures and low crystallinities（X_c<20%）.     

单茂钛/MAO体系催化乙烯/丙烯共聚合研究Ⅰ.乙烯/丙烯共聚物的合成及聚合反应规律研究

采用合成的催化剂五甲基环戊二烯基三烯丙氧基钛 [Cp Ti(OAllyl) 3]与改性甲基铝氧烷 (mMAO)组成新型催化体系进行乙烯 /丙烯共聚合 ,考察了助催化剂 (mMAO)中TMA含量、气体配比、聚合温度、助催化剂和主催化剂浓度等因素对共聚合活性及产物分子量的影响 ,研究其变化规律 .结果表明 ,Cp Ti(OAllyl) 3/mMAO催化体系中钛的价态分布为Ti(Ⅳ )时对共聚合更为有利 ,制得了乙烯 /丙烯无规共聚物弹性体     

环境友好型离子液体催化环氧丙烷反应合成丙二醇醚

丙二醇醚类化合物是性能优良的精细化学品,也是环保型高级溶剂.该类化合物具有两个强溶解性功能基团—醚键和羟基,前者具有亲油性,可溶解疏水性物质,后者具有亲水性,可溶解亲水性物质,因而丙二醇醚具有很强的溶解能力,素有"万能溶剂"之称,可广泛应用于涂料、油墨、油漆、印刷、电子化学品、染料、净洗和纺织等行业.丙二醇醚类化合物目前主要由环氧丙烷和低级脂肪醇反应合成,然而,由于环氧丙烷的位阻效应,使其在酸或碱的条件下开环的位置会不同,从而得到不同的醇醚产物.由于碱催化的醇醚产物更加环境友好,因而越来越被人们所关注.工业上丙二醇醚合成多采用传统的强碱性催化剂醇钠以及氢氧化钠,腐蚀性强,产生的废液量大.本文采用环境友好的非卤素离子液体作为催化剂,研究了其催化环氧丙烷醚化合成丙二醇醚的反应特性.本文采用两步法合成了一系列环境友好的醋酸类碱性功能化离子液体,并在温和的条件下将其用于催化环氧丙烷与醇反应合成丙二醇醚.结果表明,该类离子液体可以高效催化该反应的进行.利用紫外-可见光谱测定Hammett指数来表征实验中所用离子液体的碱强度,并构建了离子液体碱性与催化活性之间的关系.结果表明,离子液体的催化性能和其碱性密切相关,随着离子液体碱性的增加,催化活性增强,其中咪唑醋酸类离子液体碱性强于季胺类,表现出优异的催化性能.离子液体的碱性明显弱于NaOH,但却呈现出更优异的催化性能.相同反应条件下,EmimOAc离子液体作为催化剂,PO的转化率分别较NaOH高出20%–30%,选择性略高于NaOH,这可能是由于二者催化机理不同造成的.传统NaOH催化机理的关键步骤是醇在碱性催化剂的作用下去质子化形成电子供体烷氧根离子,促进环氧丙烷的开环加成.而本文提出了离子液体亲电亲核双活化作用机理,即离子液体在阴阳离子之间的氢键和电荷相互作用的共同作用下,促进环氧丙烷开环和醇的去质子化,形成相应的反应中间体.通过电喷雾质谱分析手段检测到了阴阳离子通过协同作用亲电亲核催化过程中的反应中间体,证明了该假设机理的可行性.此外,还考察了催化剂浓度、醇比、反应温度以及醇的空间位阻效应对反应的影响.以EmimOAc催化合成丙二醇丁醚为例,反应的转化率随催化剂浓度的增加而增大,在催化剂添加量1%(催化剂与PO的摩尔比)时,PO转化率达到最大值为98.2%,1-丁氧基-2-丙醇的选择性为86.4%.当正丁醇与环氧丙烷的摩尔比为3时,转化率最高为88.6%,选择性高达94%.该反应为放热反应,最适反应温度约为140 oC,此时转化率高达96.5%.在环氧丙烷和不同的低碳醇合成丙二醇醚的反应中,反应物醇的碳链越短,支链越少,催化反应效率越高.     

Alkene hydrogenation over palladium supported on a carbon–silica material

Palladium catalysts supported on a carbon–silica material were synthesized. Hydrogenation by molecular hydrogen was studied in the presence of straight-chain and cyclic olefins. As distinct from what is observed for olefins having a phenyl substituent, for aliphatic alkenes the reaction rate decreases with an increasing conversion due to the accumulation of hydrogenation products. The synthesized palladium catalysts show a higher hydrogenation activity than Pd/C.     

壳聚糖席夫碱钯催化碘代苯与丙烯酸乙酯反应

以水杨醛与壳聚糖反应制得的壳聚糖席夫碱配体再与PdCl2反应制得了壳聚糖席夫碱钯催化剂。研究了该催化剂对碘代苯(PhI)与丙烯酸乙酯(EA)偶联生成反式肉桂酸乙酯反应的催化性能。考察了原料比、缚酸剂种类及其用量、反应温度、溶剂、催化剂用量、反应时间等因素对该反应的影响,确定了该催化反应的最佳反应条件。该催化剂经过滤分离、溶剂洗涤,循环使用4次仍有较高的催化活性。     

高分子量二氧化碳-环氧丙烷共聚物的合成条件研究

利用新型多配体负载戊二酸锌来催化二氧化碳和环氧丙烷合成高分子量聚碳酸(1,2-丙二醇).通过研究反应时间和反应压力对产率以及产物的结构和性能的影响来对反应条件进行了优化.结果表明在反应压力为5.2MPa,反应时间为40h时所得聚合物的数均分子量大于23×104,玻璃化转变温度达到38℃,拉伸强度达到31MPa.     

离子液体中AM/AMPS/N8AM三元共聚物的合成及溶液性能

以丙烯酰胺(AM)和2-丙烯酰胺基-2-甲基丙磺酸(AMPS)为亲水单体, 以N-辛基丙烯酰胺(N8AM)为疏水单体, 在离子液体[bmim]BF4中实现了疏水缔合丙烯酰胺三元共聚物的合成.     

Catalytic performance of chitosan‐Schiff base supported Pd/Co bimetallic catalyst for acrylamide with phenyl halide

The chitosan‐Schiff base supported palladium and cobalt bimetallic complex was synthesized in a simple method and characterized by Fourier‐transform infrared spectroscopy (FT‐IR), powder X‐ray diffraction (XRD), and X‐ray photoelectron spectra (XPS). It was found that the catalyst has great activity and stability in the coupling of acrylamide (AA) with the phenyl halide. The influence of various bimetallic catalysts, the different molar ratio of Co/Pd, the bases, the amount of the catalyst and base, and the molar ratio of iodobenzene/AA on the reaction were investigated. The results showed that the catalytic activity of the molar ratio of Co/Pd (3/1) was the best when the iodobenzene was used as a substrate. The yield of the cinnamamide did not change significantly after ten runs. It has been revealed that the catalyst was efficient for the reaction. Copyright © 2009 John Wiley & Sons, Ltd.     

聚2,2-二甲基三亚甲基碳酸酯与壳寡糖的接枝共聚反应研究

用新戊二醇和三光气为原料,反应生成2,2-二甲基三亚甲基碳酸酯.再以四氢呋喃为溶剂,酶为催化剂引发聚2,2-二甲基三亚甲基碳酸酯（PDTC）与壳寡糖接枝生成接枝共聚物.研究了温度、时间、配比对接枝共聚物的产率和分子量的影响.就产率而言,最佳反应条件是60℃、-NH2/DTC的摩尔比值为1∶10、36 h、DTC/酶的质量比值为200;就重均分子量而言,最佳反应条件是60℃、-NH2/DTC摩尔比为1∶10、36 h、DTC/酶质量比值为150.对产品进行红外光谱、凝胶色谱与溶解性能测试.     

纤维素乙二胺负载钯配合物的制备及其对Heck反应的催化性能

合成了纤维素乙二胺负载钯（CE—Pd）配合物,用IR、XPS、TG／DTA等手段对其进行了表征．该配合物在室温至280oC范围内有很好的稳定性,在空气氛围水相中能有效地催化丙烯酸与芳基碘、苯乙烯与芳基碘的Heck芳基化反应,立体选择性地生成取代的反式肉桂酸、1,2-二苯乙烯．在80℃时反应6h,反式肉桂酸的产率达89．7％．纤维素乙二胺负载钯（CE—Pd）配合物还具有较好的重复使用性能,连续使用4次,反式肉桂酸的产率仍可达到63．5％．     

三元共聚物聚甲基乙撑-环己撑碳酸酯的合成与表征

报道了三元共聚物聚甲基乙撑-环己撑碳酸酯的制备与性能研究. 实验采用高活性的负载戊二酸锌作为催化剂, 在不添加任何溶剂的情况下, 以二氧化碳和环氧丙烷、环氧环己烷为原料, 制备了不同环己撑碳酸酯含量的三元共聚物, 并对其结构和热性能、力学性能进行了表征和分析. 结果表明这些三元共聚物具有较高的分子量, 且玻璃化转变温度随着主链上的环己撑碳酸酯含量增加而逐渐升高. 同时三元共聚物表现出比二元共聚物更好的力学性能.