Effects of uniaxial stretching and shrinkage on proton spin-lattice and spin-spin relaxation times of isotactic polypropylene

An isotactic polypropylene film was stretched at 120 °C in poly(ethylene glycol) and thermally shrunk at various temperatures. Proton spin-lattice,T ₁, and spin-spin,T ₂, relaxation times were measured using a broad line pulse spectrometer operating at 19.8 MHz in the temperature range 40 °C–100 °C. The temperature ofT ₁ minimum shifts to higher temperatures and the value ofT ₁ minimum increases in magnitude as the stretching ratio is increased. In contrast the temperature ofT ₁ minimum shifts to lower temperatures as shrinkage is increased, whereas the value ofT ₁ minimum increases in magnitude because of the increase in crystallimty during shrinkage. T_2a, the longestT ₁ associated with the mobile amorphous regions, increases during shrinkage, indicating that chain mobility in the amorphous regions increases substantially during shrinkage. It was found that an orientation function of the amorphous regions,f _a, correlates well withT _2a .Presented in part at the 52nd Annual Meeting of the Japan Chemical Society, Kyoto, April 1986.     

The acceleration of decomposition of potassium persulfate in the presence of sodium dodecyl sulfate and polymer particles as a model of emulsion polymerization system

The decomposition rates of potassium persulfate (KPS) in aqueous solutions containing sodium dodecyl sulfate (SDS) in the presence of polystyrene or poly(methyl methacrylate) particles as models of emulsion polymerization systems were measured by isotachophoresis. Free SDS molecules dispersed in the monomolecular state had an ability to accelerate the KPS decomposition, but SDS molecules adsorbed onto the polymer particles did not accelerate it.Part CXX of the series of Studies on Suspension and Emulsion     

Development of new hydrophilic polymer supports based on dimethylacrylamide

A survey of the development of hydrophilic resins based on dimethylacrylamide (DMA) is presented. It describes the preparation of DMA-based resins by suspension copolymerization of DMA and acrylamide-based crosslinking and functional monomers. Swellability data for a number of DMA-based resins are tabulated, demonstrating that the resins swell to approximately the same extent in dichloromethane as they do in water, methanol, dimethylformamide or dimethylsulphoxide, but they swell only slightly or not at all in tetrahydrofuran. Typical chemical reactions employed for quantitative estimation or derivatization of resin-bound functional groups, including those involving intra-resin crosslinking, are discussed. The development of composite polymer supports, in which the DMA-based polymer is supported on kieselguhr particles or an amphiphilic ion exchange polymer is supported on DMA-based resin beads, is also covered briefly.     

Studies of polymer solvation by dielectric relaxation spectroscopy I: polyvinyl pyrrolidone in propylene carbonate,dimethyl sulfoxide and tetramethyl urea

The dielectric relaxation behavior of the title solutions of PVP 40000 is measured in the frequency domain (50 MHz to 36 GHz) at 20 °C. The polymer content of the solutions (up to 0.25 mole fraction of monomer units) is such that it does not yet contribute significantly to dielectric loss. The solvent relaxation shows in all cases a bulk and a slowed down contribution, both characterized by concentration-independent relaxation times. The slow contribution is ascribed to the solvate. Solvation numbers for dilute solutions roughly range between 2 and 4 per PVP repeat unit.     

Preparation of asymmetric polymer film by emulsion blend technique

Two kinds of anionic polymer emulsions, of which particle sizes were greatly different, were blended and then cast on a release-paper at 30 °C. One was poly(butyl acrylate) emulsion, 0.46n in diameter, produced by emulsifier-free emulsion polymerization, and the other was ethyl acrylate-methyl methacrylate (1/1, mole ratio) copolymer emulsion, 0.02m in diameter, produced by emulsifier-containing emulsion polymerization. The film produced had asymmetric surface properties: the air-side surface was nontacky and the bottom-side surface was tacky. The forming mechanism is discussed.     

Studies of polymer solvation by dielectric relaxation spectroscopy II: Polyethylene glycol in methyl pyrrolidone

Frequency domain dielectric spectroscopy (30 MHz to 72 GHz) is utilized to study solvation in polyethylene glycol (PEG) — methyl pyrrolidone (MPy) mixtures over the whole mixture range at 20 °C, in particular with PEG 200. Further pure PEGs (200 to 400) and butyl glycol (in the pure state and in benzene and n-hexane solution) are considered for comparison to facilitate the assessment of PEG relaxational behavior. It turns out that the PEG-MPy mixtures can be described in terms of a simple solvation model which takes into account only the bulk and the solvating solvent state. The solvation number per repeat unit is about 0.85 in the dilute solution limit. It decreases gradually with increasing PEG concentration in accordance with a solvation equilibrium model.     

Chemical deposition coatings from emulsifier-free anionic polymer emulsion onto anodized aluminum plate under stirring conditions

The chemical deposition from an anionic acrylic copolymer emulsion onto an anodized aluminum plate was carried out under various stirring conditions. The amount of polymer deposited was affected by the stirring rate. At higher stirring rates, the surface flatness of the obtained coating decreased, but the transparency (which was affected by the traces of bubbles, due to evolution of hydrogen gas from the surface of the plate in the deposition process) was improved. Under optimum stirring conditions an excellent coating having a flat surface and good transparency was obtained.Part CXVIII of the series Studies on Suspension and Emulsion.     

Preparation of micron-size monodisperse polymer microspheres having cationic groups

Micron-size monodisperse crosslinked polymer microspheres having chloromethyl groups were prepared by seeded copolymerization of styrene, divinylbenzene, and chloromethylstyrene in the presence of 2.1- monodisperse polystyrene seed particles produced by dispersion polymerization. The modification reaction of chloromethyl groups on the surfaces with polyamines such as triethylenetetramine and ethylenediamine was carried out. From the measurements of potential and the amount of chloride ion released, the introduction of a large number of cationic groups at the surfaces was confirmed.Part CXXXI of the series Studies on suspension and Emulsion.     

Some aspects of polymer colloids I. Preparation and properties of different types of latex particles

The boundary region separating a latex particle from the surrounding medium has a great influence on the properties of latex dispersions. Four types of polystyrene and polystyrene/comonomer latices differing greatly in the structure of the boundary region were prepared. The first part of a series of papers reports on the preparation of the various latex dispersions. Mean particle sizes were obtained from simple turbidity measurements, quasi-elastic light scattering, and electron micrographs. The behavior of the particles in the centrifugal force field is a simple tool for detecting aggregation tendencies that are not directly related to salt stability. The BET-surface area agrees with the area calculated from the mean particle size when a sharp boundary and smooth surface is developed between the particle and the surrounding medium. In the case of particles with extended boundary regions (core/shell particles or particles with hairy envelopes), film formation reduces the specific surface area. Removal of soluble oligomers and polymers from the boundary region during subsequent treatments (purification and centrifugation before freeze-drying) can increase the surface area considerably.     

SAXS study of core-shell colloids

Polymeric core-shell systems were produced by a two-stage emulsion polymerization technique under fixed conditions: i) monodisperse seed latex with a sufficiently high particle number; ii) starved monomer-II addition; iii) water-soluble initiator; iv) incompatibility of core and shell polymer. From electron micrographs, it is not possible to determine where the second polymer is located within these two-stage emulsion polymers. The internal structure of the particles can be detected by small-angle x-ray scattering. The results indicate that; i) the emulsion polymerization process takes place in a small surface layer region of the seed particles, and ii) a small interfacial layer exists between the core and shell polymer.Part 6 of Polymerizations in the Presence of Seeds     

Production of anomalous polymer microspheres having uneven surfaces by “stepwise” heterocoagulation technique

Anomalous polymer microspheres having uneven surfaces were produced by stepwise heterocoagulation technique of small polymer particles (SPs) onto large polymer particles (LPs).SPs andLPs have surface charges opposite to each other in the emulsion states.SPs were produced by emulsion copolymerization of styrene and methacryloyloxyethyltrimethylammonium chloride, andLPs by emulsion terpolymerization of styrene, butyl acrylate and methacrylic acid, with nonionic emulsifier being used in both cases. Maximum covering ofLP bySPs was obtained under the conditions that both emulsions were blended without the coagulation at pH 3 at room temperature and then left stand to coagulate with each other at 70 °C for 4 h at pH 9.Part CXI of the series Studies on Suspension and Emulsion.     

The use of dilute solution viscometry to characterize the network properties of carbopol microgels

We used dilute solution viscometry, specifically, measurements of intrinsic viscosity and overlap concentration to characterize two members of the carbopol family, carbopols 940 and 941. These measured quantities were then used to calculate the swollen-to-dry volume ratios for both resins over a range of ionic strengths. The variation in this ratio is representative of the swelling equilibria of the micronetwork and is modeled using standard network theory with modifications for non-Gaussian chain statistics and for fixed charges on the chains. By fitting to experimental data, the cross-link density is determined as 1450 monomer units between cross-link sites for carbopol 940 and 3300 units for carbopol 941. The shear modulus of the microgel domain is then predicted from the swelling data and found to be an order of magnitude greater than the elastic modulus measured on concentrated carbopol dispersions. We argue that this discrepancy is due to a large number of defects which reduce the cycle rank of the network. Current microgel technology specifies that their rheological behavior can be predicted once the domain cross-link density is known. Simple dilute solution viscometry appears capable of providing this prerequisite.     

Dielectric relaxation in polymer solids Part 2: Application of the new model to polyurethane systems

Measurements of the complex permittivity of crosslinked polyurethanes at different temperatures in the frequency range 1–10⁵ Hz are discussed with respect to shape of relaxation curves. Using a new model (published in preceding paper) the shape parameters are related to small and large scale interaction.     

Complex polarizability as used to analyze dielectric relaxation measurements

The effect of representing dielectric properties in terms of the complex polarizability ^c = – i is examined. Loss curves ( and tan ) are shifted towards higher frequencies, revealing the existence of new relaxations and allowing the clarifications of ones already known. We have calculated the shift ratios (at maximum or tan )/ (at maximum or tan ) from the more conventional empirical equations representing the dielectric behavior. Some examples are given.     

Preparation of micron-size monodisperse polymer particles having highly crosslinked structures and vinyl groups by seeded polymerization of divinylbenzene using the dynamic swelling method

Micron-size monodisperse polystyrene/polydivinylbenzene (PS/PDVB) composite particles having highly crosslinked structures and vinyl groups were prepared as follows. First, 1.9 m-size monodisperse PS seed particles produced by dispersion polymerization were dispersed in ethanol/water (70/30, w/w) solution which dissolved divinylbenzene (DVB) monomer, benzoyl peroxide as an initiator and poly(vinyl alcohol) as a stabilizer. The PS seed particles were swollen with a large amount of DVB monomers to 4.3 m in diameter while keeping good monodispersity by the dynamic swelling method, where water was slowly added, continuously, with a micro feeder into the dispersion. And then, the seeded polymerization of the absorbed DVB was carried out.Part CXXXV of the series Studies on Suspension and Emulsion     

Estimation of distribution of vinyl groups in micron-sized monodisperse polymer microspheres by bromine titration method

The distribution of vinyl groups in polystyrene/poly(styrene-divinylbenzene) (PS/P(S-DVB)) composite microspheres produced by seeded copolymerization of S and DVB in the presence of 2.1-m monodisperse PS seed particles was estimated from the amount detected with bromine titration method as a function of the reaction time under various conditions.Part CXXIII of the series Studies on Suspension and Emulsion.     

Drug-carrying latices for prolonged release of drugs

Dichlorophene was used as a model drug. Drug-carrying latex particles were prepared by soap-free emulsion copolymerization of dichlorophene acrylate with some hydrophilic methacrylate comonomers. The comonomers used affected not only the structure and colloidal stability of particles, but also the drug-activity of particles. Preliminary study of the drug activity revealed that highly hydrophilic latex particles were very stable and too inactive to be engulfed by amoebae and kill them. On the contrary, less hydrophilic particles carrying a large amount of drug can be an effective device to release drugs at a moderate rate to fight against extracelluar targets such as parasites.     

A DSC study of PVAC-PMMA two-stage emulsion polymers

Core-shell polymer colloids were produced by a two-stage emulsion polymerization technique. The polymers thus formed were investigated by means of differential scanning calorimetry (DSC). The DSC thermograms show two separate glass transition regions of the core and the shell component with positions unchanged regardless of chemical composition. Increases in specific heat capacity at the glass transition temperature of both components are lower than theoretical values calculated from the net chemical composition. From these results, it is possible to estimate i) the chemical composition of the interfacial layer and ii) the interfacial layer thickness. This interfacial layer thickness is in the order of 2–7 nm.Part 7 of Polymerizations in the Presence of Seeds     

Polymer coatings onto anodized aluminum plate by anodic electrodeposition from alkali-swollen carboxylated acrylic emulsion

Polymer coating of an anodized aluminum plate was carried out by anodic electrodeposition from alkali-swollen ethyl acrylate-methyl methacrylate-methacrylic acid (45/45/10, mole ratio) terpolymer emulsion with dimethyl aminoethanol. The alkali-swollen state was controlled by heating time at 60°C prior to the elctrodeposition. The similar complicated behaviors were observed in the relationships between the alkali-swollen state and the primary current density, the current density after 2 min, the quantity of electricity, and the amount of polymer deposited. The appearance of coatings changed correspondingly with such behaviors. These results indicate that the properties of the coatings are complicatedly affected by the degree of alkali-swollen state.Part CXII of the series Studies on Suspension and Emulsion.