Magnetic and structural properties of CaO–SiO2–P2O5–Na2O–Fe2O3 glass ceramics

Magnetic properties of glass ceramics derived from glasses with composition 41CaO·(52−x)SiO₂·4P₂O₅·xFe₂O₃·3Na₂O (2?x?10 mol% iron oxide (Fe₂O₃)) are reported. Structural investigation revealed the presence of nanocrystalline magnetite phase in the heat-treated samples containing x?2 mol% Fe₂O₃. Magnetic hysteresis cycles of the glass-ceramic samples were obtained with a maximum applied field of ±20 kOe as well as a low field of ±500 Oe, in order to evaluate the potential of these glass ceramics for hyperthermia treatment of cancer. Samples with x>2 mol% of iron oxide exhibited magnetic behavior similar to soft magnetic materials with low coercivity. The evolution of magnetic properties in these samples as a function of iron oxide molar concentration is correlated with the amount and crystallite size of magnetite phase present in them.     

Effects of BaCu（B2O5 ） addition on sintering temperature and microwave dielectric properties of Ba5Nb4O15–BaWO4 ceramics

The effects of BaCu(B2O5)(BCB) addition on the microstructure, phase formation, and microwave dielectric properties of Ba5Nb4O15–BaWO4ceramic are investigated. As a sintering aid, BaCu(B2O5) ceramic could effectively lower the sintering temperature of Ba5Nb4O15–BaWO4ceramic from 1100?C to 950?C due to the liquid-phase effect. Meanwhile,BaCu(B2O5) addition effectively improves the densification of Ba5Nb4O15–BaWO4ceramic and significantly influences the microwave dielectric properties. X-ray diffraction analysis reveals that Ba5Nb4O15and BaWO4coexist with no crystal phase of BaCu(B2O5) in the sintered ceramics. The Ba5Nb4O15–BaWO4ceramics with 1.0 wt% BaCu(B2O5) sintered at 950?C for 2 h presents good microwave dielectric properties of εr = 19.0, high Q × f of 33802 GHz and low τfof2.5 ppm/?C.     

Preparation and high-temperature properties of Au nano-particles doped α-Al2O3 composite coating on TiAl-based alloy

Au nano-particles doped α-Al₂O₃ composite coatings were successfully prepared on TiAl-based alloy by electrodeposition, using the Al₂O₃ sols with minor addition of HAuCl₄ solution. The even distribution of Au nano-particles (<2.0 wt.%) in the α-Al₂O₃ matrix has been observed. Isothermal oxidation tests of the samples coated with the as-prepared novel coatings at 900 °C in static air for 200 h shown that the oxygen inward diffusion can be effectively suppressed to a low level. The results of high-temperature cyclic oxidation test at 900 °C in air revealed that the oxidation and spallation resistance of TiAl-based alloy were improved significantly under thermal cycling. In the as-prepared coatings, cracks were shielded by means of crack bridging and the fracture resistance of the formed scales can be improved by toughening effects of the composite structure. Surface scratching tests after the cyclic oxidation exhibited that the adhesion of the formed composite scale on TiAl-based alloy was remarkably improved by the Au nano-particles doped α-Al₂O₃ composite coating.     

Synthesis and properties of Au-Fe3O4 and Ag-Fe3O4 heterodimeric nanoparticles

Monodisperse Au-Fe 3 O 4 heterodimeric nanoparticles (NPs) were prepared by injecting precursors into a hot reaction solution.The size of Au and Fe 3 O 4 particles can be controlled by changing the injection temperature.UV-Vis spectra show that the surface plasma resonance band of Au-Fe 3 O 4 heterodimeric NPs was evidently red-shifted compared with the resonance band of Au NPs of similar size.The as-prepared heterodimeric Au-Fe 3 O 4 NPs exhibited superparamagnetic properties at room temperature.The Ag-Fe 3 O 4 heterodimeric NPs were also prepared by this synthetic method simply using AgNO 3 as precursor instead of HAuCl 4.It is indicated that the reported method can be readily extended to the synthesis of other noble metal conjugated heterodimeric NPs.     

Physical,optical and radiative properties of CaSO4–B2O3–P2O5 glasses doped with Sm3+ ions

Trivalent rare earth ions doped borosulfophosphate glasses are in high demand owing to their several unique attributes that are advantageous for applications in diverse photonic devices. Thus, Sm³⁺ ion doped calcium sulfoborophosphate glasses with composition of 25CaSO₄–30B₂O₃–(45?x)P₂O₅–xSm₂O₃ (where x?=?0.1, 0.3, 0.5, 0.7 and 1.0 mol%) were synthesized using melt-quenching technique. X-ray diffraction confirmed the amorphous nature of the prepared glass samples. Differential thermal analyses show transition peaks for melting temperature, glass transition and crystallization temperature. The glass stability is found in the range 91?°C to 116?°C which shows increased stability with addition of Sm₂O₃ concentration. The Fourier transform infrared spectral measurements carried out showed the presence of vibration bands due to PO linkage, BO_3, BO₄, PO₄, POP, OPO, SOB, and BOB unit. Glass density showed increase in value from 2.179 to 2.251?g cm^?3 with increase in Sm₂O₃ concentration. The direct, indirect band gap and Urbach energy calculated were found to be within 4.368–4.184?eV, 3.641–3.488?eV and 0.323–0.282?eV energy ranges, respectively. The absorption spectra revealed ten prominent peaks centered at 365, 400, 471, 941, 1075, 1228, 1375, 1477, 1528 and 1597?nm corresponding to ⁴D_3/2,⁶H_5/2→⁴I_11/2,⁶P_3/2, ⁶F_11/2, ⁶F_9/2, ⁶F_7/2, ⁶F_5/2, ⁶F_3/2, ⁶H_15/2 and ⁶F_1/2 transitions respectively. Photoluminescence spectra monitored at the excitation of 398?nm exhibits four emission bands positioned at 559, 596,643 and 709?nm corresponding to ⁴G_5/2→⁶H_5/2, ⁶H_7/2, ⁶H_9/2 and ⁶H_11/2 transitions respectively. The nephelauxetic parameters calculated showed good influence on the local environment within the samarium ions site and the state of the SmO bond. The Judd–Ofelt intensity parameters calculated for all glass samples revealed that Ω_6?>?Ω_4?>?Ω₂. The emission cross-section and the branching ratios values obtained for ⁴G_5/2→⁶H_7/2 transition indicate its suitability for LEDs and solid-state laser application.     

Investigation of structural,physical and optical properties of CeO2–Bi2O3–B2O3 glasses

xCeO₂–30Bi₂O₃–(70−x) B₂O₃ glasses are synthesized by using the melt quench technique. A number of studies such as XRD, density, molar volume, optical band gap, refractive index and FTIR spectroscopy are employed to characterize the glasses. The band gap decreases from 2.15 to 1.61 eV, refractive index increases from 2.67 to 2.93 and density increases from 4.151 to 4.633 g/cm³. The decrease in band gap with CeO₂ doping approaches the semiconductor behavior. FTIR spectroscopy reveals that incorporation of CeO₂ into glass network helps to convert the structural units of [BO₃] into [BO₄] and results in Bi–O bond vibration of [BiO₆].     

Transparent nano composite PVA–TiO2 and PMMA–TiO2 thin films: Optical and dielectric properties

Transparent nano composite PVA–TiO₂ and PMMA–TiO₂ thin films were prepared by an easy and cost effective dip coating method. Al/PVA–TiO₂/Al and Al/PMMA–TiO₂/Al sandwich structures were prepared to study the dielectric behavior. The presence of metal–oxide (Ti–O) bond in the prepared films was confirmed by Fourier transform infrared spectroscopy. X-ray diffraction pattern indicated that the prepared films were predominantly amorphous in nature. Scanning electron micrographs showed cluster of TiO₂ nanoparticles distributed over the film surface and also there were no cracks and pin holes on the surface. The transmittance of the films was above 80% in the visible region and the optical band gap was estimated to be about 3.77 eV and 3.78 eV respectively for PVA–TiO₂ and PMMA–TiO₂ films by using Tauc's plot. The determined refractive index (n) values were between 1.6 and 2.3. High value of dielectric constant (?′ = 24.6 and ?′ = 26.8) was obtained for the prepared composite films. The conduction in the composite films was found to be due to electrons. The observed amorphous structure, good optical properties and dielectric behavior of the prepared nano composite thin films indicated that these films could be used in opto-electronic devices and in thin film transistors.     

Preparation, characterization and dye adsorption properties of γ-Fe2O3/SiO2/chitosan composite

A γ-Fe₂O₃/SiO₂/chitosan composite was prepared by water-in-oil emulsification, and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM). Effects of various factors, including adsorbent dosage, initial dye concentration, solution pH, and competing anions, on the adsorption of methyl orange from aqueous solutions by the resulting composite were studied by batch adsorption experiments. The adsorption kinetics was found to follow the pseudo-second-order kinetic model, and intraparticle diffusion was related to the adsorption, but not as a sole rate-controlling step. The equilibrium adsorption data were well described by the Freundlich isotherm model. Evaluation of the thermodynamic parameters ΔG°, ΔH°, and ΔS° revealed that the adsorption process was naturally feasible, spontaneous, and exothermic. The composite was proven to be efficient, suitable and promising for the removal of methyl orange from aqueous solutions since it has a relatively higher adsorption capacity than other low-cost adsorbents.     

Temperature-frequency dependence and mechanism of dielectric properties for γ-Y2Si2O7

This paper reports that single-phase γ-Y2Si2O7 is prepared via a sufficient blending and cold-pressed sintering technique from Y2O3 powder and SiO2 nanopowder. It studies the dielectric properties of γ-Y2Si2O7 as a function of the temperature and frequency. The γ-Y2Si2O7 exhibits low dielectric loss and non-Debye relaxation behaviour from 25 to 1400℃ in the range of 7.3-18 GHz. The mechanism for polarization relaxation of the as-prepared γ-Y2Si2O7 differing from that of SiO 2 is explained. Such particular dielectric properties could potentially make specific attraction for extensive practical applications.     

Preparation and characteristics of?a?BaO–Al2O3–B2O3–SiO2–La2O3 glass ceramic via spray pyrolysis

The characteristics of a BaO–Al₂O₃–B₂O₃–SiO₂–La₂O₃ glass ceramic prepared by spray pyrolysis were studied. Glass powders with spherical shape and amorphous phase were prepared by complete melting at a preparation temperature of 1 500°C. The mean size and geometric standard deviation of the powders prepared at the temperature of 1 500°C were 0.6 μm and 1.3. The glass powders had similar composition to that of the spray solution. The glass transition temperature (T _g) of the glass powders was 600.3°C. Two crystallization exothermic peaks were observed at 769.3 and 837.8°C. Densification of the specimen started at a sintering temperature of 600°C, in which Ba₄La₆O(SiO₄)₆ as main crystal structure was observed. Complete densification of the specimen occurred at a sintering temperature of 800°C. The specimens sintered at temperatures above 800°C had main crystal structure of BaAl₂Si₂O₈.     

Zn2 SnO4 立方体的水热合成及其荧光性质

利用水合肼作缓释型碱源和络合剂,采用水热法合成了Zn₂SnO₄立方多面体。XRD物相分析表明,产物为结晶良好的立方反尖晶石结构Zn₂SnO₄。FESEM和TEM形貌分析表明,该Zn₂SnO₄微晶为边长100~400 nm左右的立方体,其光致发光光谱是蓝-绿光发射带(中心590 nm处),在400 ℃空气气氛下退火1 h后,蓝-绿光发射带的强度显著降低。这主要是因为退火处理提高了晶体质量,降低了氧空位浓度,从而降低了可见光发射带的强度。     

Microstructure and dielectric properties of Li2CO3 doped 0.7(Ba,Sr)TiO3–0.3MgO ceramics

Microstructure and dielectric properties of Li₂CO₃ doped 0.7(Ba,Sr)TiO₃–0.3MgO ceramics for the low temperature sintering and microwave applications will be presented. In these days, low temperature sintering process has been widely spread out for the integrated electronic modules for the communication systems such as front-end modules, antenna modules, and switching modules. We have added Li₂CO₃ and MgO to (Ba,Sr)TiO₃ material to reduce the sintering temperature and improve dielectric properties such as loss tangent, and frequency dispersion.In this paper, we have discussed the crystalline properties, dielectric properties, and the microstructures of Li₂CO₃ doped 0.7(Ba,Sr)TiO₃–0.3MgO ceramics. No pyro phase was observed in the X-ray diffraction method. Very weak frequency dispersion (<0.7%) of dielectric permittivity was observed from the 1 kHz to 1 MHz range. We found that the grain size of BST is around 2 μm, while the grain size of Li₂CO₃ dope 0.7BST–0.3MgO is around 4 μm from the SEM analysis.     

Electronic and thermodynamic properties of α-Pu2O3

Based on density functional theory+U$\text{density functional theory}+U$ calculations and the quasi-annealing simulation method, we obtain the ground electronic state for α-Pu₂O₃ and present its phonon dispersion curves as well as various thermodynamic properties, which have seldom been theoretically studied because of the huge unit cell. We find that the Pu–O chemical bonding is weaker in α-Pu₂O₃ than in fluorite PuO₂, and subsequently a frequency gap appears between oxygen and plutonium vibration density of states. Based on the calculated Helmholtz free energies at different temperatures, we further study the reaction energies for Pu oxidation, PuO₂ reduction, and transformation between PuO₂ and α-Pu₂O₃. Our reaction energy results are in agreements with available experiment. And it is revealed that high temperature and insufficient oxygen environment are in favor of the formation of α-Pu₂O₃.     

Y2O3·Cr2O3复合氧化物热力学性质的研究

在1182—1386K温度范围内,用固体电解质氧浓差电池:Mo|Cr,Y₂O₃,Y₂O₃·Cr₂O₃|ZrO₂(+MgO)|Cr,Cr₂O₃|Mo测定了复合氧化物Y₂O₃·Cr₂O₃的热力学性质。对于反应Y_{2关键词：}     

Luminescent properties of YVO4:Eu/SiO2 core–shell composite particles

We report an efficient process for preparing monodisperse SiO₂@Y_0.95Eu_0.05VO₄ core–shell phosphors using a simple citrate sol–gel method and without the use of surface-coupling silane agents or large stabilizers. X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and photoluminescence (PL) spectra were used to characterize the resulting SiO₂@Y_0.95Eu_0.05VO₄ core–shell phosphors. The XRD results demonstrate that the Y_0.95Eu_0.05VO₄ particles crystallization on the surface of SiO₂ annealing at 800 °C is perfectly and the crystallinity increases with raising the annealing temperature. The obtained core–shell phosphors have a near perfect spherical shape with narrow size distribution (average size ca. 500 nm and an average thickness of ~50 nm), are not agglomerated, and have a smooth surface. The thickness of the YVO₄:Eu³⁺ shells on the SiO₂ cores could be easily tailored by changing the mass ratio of shell to core (W = [YVO₄]/[SiO₂]) (~50 nm for W = 30%). The Eu³⁺ shows a strong PL luminescence (dominated by ⁵D₀ − ⁷F₂ red emission at 618 nm) under the excitation of 320 nm UV light. The PL intensity of Eu³⁺ increases with increasing the annealing temperature and the values of W.     

Preparation and photocatalytic properties of hybrid core–shell reusable CoFe2O4–ZnO nanospheres

Magnetically separable and reusable core–shell CoFe₂O₄–ZnO photocatalyst nanospheres were prepared by the hydrothermal synthesis technique using glucose derived carbon nanospheres as the template. The morphology and the phase of core–shell hybrid structure of CoFe₂O₄–ZnO were assessed via TEM, SEM and XRD. The magnetic composite showed high UV photocatalytic activity for the degradation of methylene blue in water. The photocatalytic activity was found to be ZnO shell thickness dependent. Thicker ZnO shells lead to higher rate of photocatalytic activity. Hybrid nanospheres recovered using an external magnetic field demonstrated good repeatability of photocatalytic activity. These results promise the reusability of the hybrid nanospheres for photocatalytic activity.     

Photoluminescence properties of rare earth doped α-Si3N4

The photoluminescence properties of Eu²⁺, Ce³⁺ and Tb³⁺ doped α-Si₃N₄ have been studied and a possible structural model has been proposed on the basis of the Rietveld refinement of X-ray powder diffraction data. Nearly single phase rare earth doped α-Si₃N₄ was synthesized by a solid state reaction at 1600 °C in N₂-H₂ atmosphere starting from amorphous Si₃N₄ and rare earth oxides or nitrides. Because of small crystal field splitting of the 5d levels, the excitation and emission bands of Eu²⁺ and Ce³⁺ are positioned at higher energies as isolated ions in comparison with that in Ca-α-Sialon. Both Eu²⁺- and Ce³⁺-doped α-Si₃N₄ show blue band emission peaking at about 470 and 450 nm, respectively, under UV excitation. α-Si₃N₄:Tb³⁺ exhibits dominant green line emission mainly arising from ⁵D₄→⁷F_J (J=6-3) with weak ⁵D₃→⁷F_J (J=6-3) transitions of Tb³⁺ when excited by UV light. The thermal stability of α-Si₃N₄:Eu²⁺ is comparable with that of Ca-α-Sialon:Eu²⁺ and is much better than that of α-Si₃N₄:Ce³⁺.     

Holographic properties of Fe3O4 nanoparticle-doped organic–inorganic hybrid photopolymer

An organic–inorganic hybrid photopolymer doped with sodium-citrate-coated Fe₃O₄ nanoparticles was fabricated. The experimental results showed that the maximum diffraction efficiency could be increased from 69 to 90%, and the maximum refractive index modulation improved from 1.386 × 10⁻³ to 2.083 × 10⁻³. It also found that the volume shrinkage during holographic exposure was noticeably suppressed without affecting the optical quality of the photopolymer.