Simultaneous sample washing and concentration using a "trapping-and-releasing" mechanism of magnetic beads on a microfluidic chip

Simultaneous washing and concentration of functionalized magnetic beads in a complex sample solution were demonstrated by applying a rotational magnetic actuation system to a microfluidic chip under continuous flow conditions. The rotation of periodically arranged small permanent magnets close to the fluidic channel carrying a magnetic bead suspension allows trapping and releasing of the beads along the fluidic channel in a periodical manner. Each trapping and releasing event resembles one washing cycle. A purification efficiency of magnetic beads out of a mixed magnetic and non-magnetic bead sample solution of 83±4% at a flow rate of 0.5 μL min(-1), and a magnetic bead recovery or concentration efficiency of 91±5% were achieved using a flow rate of 0.2 μL min(-1). The detection performance of the device was experimentally evaluated with two different bioassays, using either streptavidin-coated magnetic beads in combination with biotinylated fluorescent isothiocyanate (FITC), or a mouse antigen (Ag)-antibody (Ab) system.     

Flow-through immunomagnetic separation system for waterborne pathogen isolation and detection: Application to Giardia and Cryptosporidium cell isolation

Simultaneous sample washing and concentration of two waterborne pathogen samples were demonstrated using a rotational magnetic system under continuous flow conditions. The rotation of periodically arranged small permanent magnets close to a fluidic channel carrying magnetic particle suspension allows the trapping and release of particles along the fluidic channel in a periodic manner. Each trapping and release event resembles one washing cycle.The performance of the magnetic separation system (MSS) was evaluated in order to test its functionality to isolate magnetic-labelled protozoan cells from filtered, concentrated tap water, secondary effluent water, and purified water. Experimental protocols described in US Environmental Protection Agency method 1623 which rely on the use of a magnetic particle concentrator, were applied to test and compare our continuous flow cell separation system to the standard magnetic bead-based isolation instruments. The recovery efficiencies for Giardia cysts using the magnetic tube holder and our magnetic separation system were 90.5% and 90.1%, respectively, from a tap water matrix and about 31% and 18.5%, respectively, from a spiked secondary effluent matrix. The recovery efficiencies for Cryptosporidium cells using the magnetic tube holder and our magnetic separation system were 90% and 83.3%, respectively, from a tap water matrix and about 38% and 36%, respectively, from a spiked secondary effluent matrix. Recoveries from all matrices with the continuous flow system were typically higher in glass tubing conduits than in molded plastic conduits.     

Human Saliva-Based Quantitative Monitoring of Clarithromycin by Flow Injection Chemiluminescence Analysis: A Pharmacokinetic Study

Human saliva quantitative monitoring of clarithromycin (CLA) by chemiluminescence (CL) with flow injection analysis was proposed for the first time, which was based on the quenching effect of CLA on luminol–bovine serum albumin (BSA) CL system with a linear range from 7.5?×?10^?4 to 2.0 ng/ml. This proposed approach, offering a maximum sample throughput of 100 h^?1, was successfully applied to the quantitative monitoring of CLA levels in human saliva during 24 h after a single oral dose of 250 mg intake, with recoveries of 95.2～109.0 % and relative standard deviations lower than 6.5 % (N?=?7). Results showed that CLA reached maximum concentration of 2.28?±?0.02 μg/ml at approximately 3 h, and the total elimination ratio was 99.6 % in 24 h. The pharmacokinetic parameters including absorption rate constant (0.058?±?0.006 h^?1), elimination rate constant (0.149?±?0.009 h^?1) and elimination half-life time (4.66?±?0.08 h) were obtained. A comparison of human saliva and urine monitoring was also given. The mechanism study of BSA–CLA interaction revealed the binding of CLA to BSA is an entropy driven and spontaneous process through hydrophobic interaction, with binding constant K _BSA–CLA of 4.78?×?10⁶ l/mol and the number of binding sites n of 0.82 by flow injection–chemiluminescence model. Molecular docking analysis further showed CLA might be in subdomain IIA of BSA, with K _BSA–CLA of 6.82?×?10⁵ l/mol and ΔG of ?33.28 kJ/mol.     

Rapid and Highly Sensitive HPLC and TLC Methods for Quantitation of Amlodipine Besilate and Valsartan in Bulk Powder and in Pharmaceutical Dosage Forms and in Human Plasma

Two simple, sensitive, and specific high-performance liquid chromatography and thin-layer chromatography methods were developed for the simultaneous estimation of Amlodipine besilate (AM) and Valsartan (VL). Separation by HPLC was achieved using a xTerra C18 column and methanol /acetonitrile /water/ 0.05% triethylamine in a ratio 40:20:30:10 by volume as mobile phase, pH was adjusted to 3 ± 0.1 with o-phosphoric acid. The flow rate was 1.2 mL min^?1. The linearity range was 0.2 to 2 µg mL^?1 for amlodipine besilate and 0.4 to 4 µg mL^?1 for Valsartan with a mean percentage recovery of 99.59 ± 0.523% and 100.61 ± 0.400% for amlodipine besilate and valsartan, respectively. The TLC method used silica gel 60 F₂₅₄ plates; the optimized mobile phase was ethyl acetate/ methanol / ammonium hydroxide (55:45:5 by volume). Quantitatively, the spots were scanned densitometrically at 237 nm. The range was 0.5–4.0 µg spot^?1 for amlodipine besilate and 2.0–12.0 µg spot^?1 for valsartan. The mean percentages recovery was 99.80 ± 0.451% and 100.61 ± 0.363% for amlodipine besilate and valsartan, respectively. The HPLC method was found to be simple, selective, precise, and reproducible for the estimation of both drugs from spiked human plasma.     

Immunomagnetic nanoparticle-based sandwich chemiluminescence-ELISA for the enrichment and quantification of E. coli

Rapid methods for the quantification of Escherichia coli are required for the monitoring of faecal contamination in water to secure public health. The immunomagnetic separation (IMS) offers rapid enrichment and purification of bacteria in complex matrices and is compatible with immunoassays. By means of this technique, non-target cells and matrix components which might interfere with subsequent analytical methods are removed. We present the synthesis of magnetic nanoparticles (MNPs) and covalent coupling to antibodies against the enterobacterial common antigen (ECA) for use with IMS. Quantification was carried out with a chemiluminescence-based sandwich enzyme-linked immunosorbent assay (ELISA). Our anti-ECA-MNPs allow for a group-specific enrichment of bacterial cells, which can be combined with a species-specific analytical method. The particles were used along with commercially available magnetic columns for the selective enrichment of E. coli from 10-mL water samples. The volumetric enrichment factor was 9. For enriched samples, the limit of detection was reduced from 5.0?×?10⁶ cells·mL^-1 to 2.6?×?10⁵ cells·mL^-1. Using 200 µL anti-ECA-MNPs, we determined a recovery of 97?±?6% for a sample containing 10⁶ cells·mL^-1 and 89?±?2% for a sample containing 10⁷ cells·mL^-1. The overall time for cell enrichment and detection was 3 h 45 min.     

Simultaneous Estimation of Atorvastatin Calcium, Ramipril and Aspirin in Capsule Dosage Form by RP-LC

A simple, sensitive, precise and accurate reversed phase liquid chromatographic method has been developed for the simultaneous estimation of atorvastatin (AT) calcium, ramipril (RA) and aspirin (AS) from capsule dosage form. The method was developed using a Phenomenex Luna C₁₈ (250 mm, 4.6 mm i.d., 5 µm) column with a mobile phase consisting of 0.1%, orthophosphoric acid buffer:acetonitrile:methanol (45:50:5 v/v/v), pH 3.3, at a flow rate of 1 mL min^?1. Detection was carried out with ultra-violet detection at 210 nm. The retention times were about 12.19, 2.35, and 3.95 min for AT calcium, RA and AS, respectively. The developed method was validated for linearity, accuracy, precision, limit of detection, limit of quantitation and robustness. The linearity ranges were 1–6 µg mL^?1 for AT calcium, 0.5–3 µg mL^?1 for RA and 7.5–45 µg mL^?1 for AS with mean recoveries of 100.59 ± 0.68, 100.62 ± 0.83 and 100.49 ± 0.73% for AT calcium, RA and AS, respectively. Limit of detection obtained were 29.85 ng mL^?1 for AT calcium, 4.71 ng mL^?1 for RA and 85.13 ng mL^?1 for AS. Impurity of salicylic acid was found in capsule dosage form at the retention time of about 4.84 min. The proposed method can be used for the estimation of these drugs in combined dosage forms.     

Determination of Puerarin in Pharmaceutical Injection by Flow Injection Analysis with Acidic Potassium Permanganate–Glyoxal Chemiluminescence Detection

Abstract

A simple flow injection chemiluminescence method with synergistic enhancement has been investigated for the rapid and sensitive determination of puerarin. The method is based on the enhancing effect of puerarin on the chemiluminescence emission generated by the oxidation of glyoxal with potassium permanganate in a sulfuric acid medium. The optimization of chemical variables influencing the chemiluminescence response of the method has been carried out by applying experimental design, using the proposed flow?injection manifold. Under the optimal conditions, the enhanced chemiluminescence intensity was linear with the concentration of puerarin over the range from 10.0 ng · ml^?1 to 7.0 µg · ml^?1 (R²=0.9972) with a detection limit (3σ) of 3.0 ng · ml^?1. At a flow rate of 3.0 ml · min^?1, a complete analytical process could be performed within 0.5 min, including sampling and washing, with a relative standard deviation of less than 3.0%. The proposed method was applied successfully in the assay of puerarin in pharmaceutical injection and human urine. The mechanism of chemiluminescence reaction was discussed briefly.     

Regulation of vincamine biosynthesis and associated growth promoting effects through abiotic elicitation,cyclooxygenase inhibition,and precursor feeding of bioreactor grown Vinca minor hairy roots

Hydroxylase/acetyltransferase elicitors and cyclooxygenase inhibitor along with various precursors from primary shikimate and secoiridoid pools have been fortified to vincamine less hairy root clone of Vinca minor to determine the regulatory factors associated with vincamine biosynthesis. Growth kinetic studies revealed that acetyltransferase elicitor acetic anhydride and terpenoid precursor loganin significantly reduce the growth either supplemented alone or in combination (GI?=?140.6?±?18.5 to 246.7?±?24.3), while shikimate and tryptophan trigger biomass accumulation (GI?=?440.2?±?31.5 to 540.5?±?40.3). Loganin also downregulates total alkaloid biosynthesis. Maximum flux towards vincamine production (0.017?±?0.001 % dry wt.) was obtained when 20-day-old hairy roots were fortified with secologanin (10 mg/l) along with tryptophan (100 mg/l), naproxen (8.4 mg/l), hydrogen peroxide (20 μg/l), and acetic anhydride (32.4 mg/l). This was supported by RT PCR (qPCR) analysis where 2- and 3-fold increase in tryptophan decarboxylase (TDC; RQ?=?2.0?±?0.09) and strictosidine synthase (STR; RQ?=?3.3?±?0.36) activity, respectively, was recorded. The analysis of variance (ANOVA) for growth kinetics, total alkaloid content, and gene expression studies favored highly significant data (P?<?0.05–0.01). Above treated hairy roots were also up-scaled in a 5-l stirred-tank bioreactor where a 40-day cycle yielded 8-fold increase in fresh root mass.     

Ultrasensitive Assay of Gatifloxacin at Picogram Level Based on its Enhancing Effect on the Myoglobin‐Luminol Chemiluminescence Reaction

Abstract

Picogram‐level gatifloxacin was determined based on its significantly catalyzed effect on myoglobin‐luminol chemiluminescence (CL) reaction in the flow injection system. The enhanced chemiluminescence intensity was linear with gatifloxacin concentration in the range from 50 ngl^?1–10 µg l^?1 (r²=0.9995), and the detection limit was 20 ng l^?1 (3σ). At a flow rate of 2.0 ml min^?1 for each line, a complete analytical process could be performed within 0.5 min, including sampling and washing, with a relative standard deviation of less than 4.0% (n=7). The proposed method was applied successfully in the determination of gatifloxacin in tablets, human serum and urine samples with the recovery from 97.4–104.5%.     

A Rotary Polydimethylsiloxane‐Based Device for Polymerase Chain Reaction

Abstract

A novel rotary channel polymerase chain reaction (PCR) microchip with polydimethylsiloxane (PDMS) is developed in our laboratory. The chip circular platinum thin‐film heaters and thermometers. Compared with other continuous‐flow PCR chips, the novel rotary channel and the circular heating arrangements in this chip make the loaded reagent mixture pass through three constant‐temperature zones in a very direct sequence, which avoids a melted sample's subjection to the extension temperature before reaching the annealing zone and improves the PCR yield effectively. Several experiments are performed to verify the ability of the device. The results show that the device achieves 25 cycles in 35 min with flow rate 3 µl/min compared to about 45 min in a standard batch PCR system.     

The Effects of Caffeine Ingestion Before Passive Heat Loading on Serum Leptin Levels in Humans

We assessed the effects of ingesting caffeine before passive heat loading (PHL) on serum leptin and sweating response, which are both physiological responses associated with energy expenditure. The subjects were nine male university students (age, 24.1?±?3.5 years; height, 173.4?±?7.6 cm; weight, 69.2?±?5.7 kg; maximal oxygen consumption, 48.6?±?4.7 ml???kg^?1???min^?1). This study used a within-subject, random, crossover design. Tests were performed twice at the same time (2–5 p.m.) at a 1-week interval following 3 mg?kg^?1 caffeine ingestion (Caff-I) or not (No-Caff). PHL included a half bath in hot water (42?±?0.5 °C for 30 min) in a thermoneutral climate chamber (25?±?0.5 °C, 60?±?3 % relative humidity, <1 m/s air velocity). After PHL, blood levels of leptin and free fatty acids were significantly higher in the Caff-I compared to those in the No-Caff after PHL (P?<?0.01). Waist circumference and whole-body sweat loss volume were significantly higher in the Caff-I compared to those in the No-Caff (P?<?0.001). Mean active sweat gland density was significantly higher in the Caff-I compared to those in the No-Caff at 10 min during PHL (P?<?0.001). The results suggest that ingesting caffeine before PHL is more energy efficient than that of a single PHL.     

Determination and Characterization of the Uptake of Voriconazole in Human Lung Epithelial Cells by High-Performance Liquid Chromatography–Tandem Mass Spectrometry

Voriconazole is used to prevent invasive pulmonary aspergillosis. However, little is known about the concentrations of voriconazole in human lung epithelial cells (A549), which is the target for preventing invasive pulmonary aspergillosis. The goal of this study was to develop a high-performance liquid chromatography–tandem mass spectrometry method to quantify voriconazole in A549 cells. A triple-quadrupole mass spectrometer in selected reaction monitoring mode was used with positive electrospray ionization. The total duration of each run was 5?min. The calibration curves fit a least squares model for the voriconazole concentration ranging from 0.625 to 160?ng/mL. Intraday and interday coefficients of variation were less than 10%. Recoveries at the concentrations of the quality control samples where greater than 85%, and the matrix effects showed that the ratios of the peak response exhibited a 15% suppression of the signal in the matrix compared to water. Voriconazole may penetrate A549 cells. However, the voriconazole uptake was slow in A549 cells, reaching a plateau at 2?h, where the dose-dependent intracellular voriconazole concentrations were 1.98?±?0.38, 4.43?±?0.54, and 8.14?±?0.52?ng/mg protein for extracellular voriconazole concentrations of 5, 10, and 20?µg/mL, respectively. The uptake of voriconazole by A549 cells was linear at extracellular concentrations from 0 to 20?µg/mL. This study established a rapid and sensitive method suitable for determining voriconazole in A549 cells and described the kinetic properties of the absorption of voriconazole by A549 cells.     

A sensitive RP-HPLC method for estimation of artemether from polymeric nanoparticles after pre-column acid treatment using UV-visible detector

Abstract

Artemether; a sesquiterpene lactone is widely used for the treatment of malaria as artemisinin-based combination therapy (ACT). The present work involves the development and validation of sensitive reversed-phase high-performance liquid chromatography (RP-HPLC) method for quantification of artemether (ART) in polymeric nanoparticles. ART was transformed to α, β-unsaturated decalones by pre-column acid treatment to enhance the sensitivity of chromophoric group lacking ART for quantification by HPLC-UV. Waters Spherisorb^® 5?µm ODS(C18) column (4.6*250?mm) with gradient elution by mobile phase comprising of ACN and PBS (10?mM; pH 6.0) was used to separate acid-treated ART. The analysis was carried at λ_max of 253?nm with 20?min and 20?µL run time and injection volume, respectively. The method was found to be linear in the concentration range of 0.5–10?µg mL^?1 with 0.09?µg mL^?1 and 0.27?µg mL^?1 as LOD and LOQ respectively. Further, the method was also found to be specific for ART in presence of blank polymeric nanoparticles, accurate (% average recovery rate 101.7?±?1.68%), precise (RSD <2%), and robust. The method was successfully used to determine % entrapment efficiency and in vitro release of ART-loaded polymeric nanoparticles with HPLC using a UV-visible detector.     

Development and Validation of a Solid Phase Extraction and LC-MS Method for the Determination of Caulophine in Rat Plasma and Tissue: Application to Study Its Pharmacokinetics

A rapid and sensitive liquid chromatography-mass spectrometric (LC-MS) method was developed for investigating the pharmacokinetics of caulophine in rats. Biological samples were isolated by solid phase extraction (SPE) and analyzed by the LC-MS. A Shimadzu C18 VP-ODS column (150 mm × 2.0 mm ID, 5 µm) was used as the analytical column, with methanol-water-formic acid (33:67:0.1) as the mobile phase and a flow rate of 0.2 mL/min. Within-day and between-day precision was 1.40–3.49% and 1.29–6.91%. Average recoveries for all matrices were greater than 85.0%. The main pharmacokinetic parameters were T_max = (0.84 ± 0.31) h, C_max = (0.22 ± 0.08) µg/mL, AUC = (0.87 ± 0.16) h · µg/mL.     

Somatic Embryogenesis and Synthetic Seed Production—a Biotechnological Approach for True-to-Type Propagation and In Vitro Conservation of an Ornamental Bulbaceous Plant Drimiopsis kirkii Baker.

An efficient plant regeneration protocol through indirect somatic embryogenesis pathway via callus had been developed from the leaf explant of an ornamental bulbaceous plant Drimiopsis kirkii. Optimum friable calli were induced on Murashige and Skoog (MS) basal medium supplemented with 3.0 mg/l of 2,4-dichlorophenoxyacetic acid and 1.0 mg/l of α-naphthalene acetic acid (NAA). On subculturing the callus on MS medium supplemented with 2.5 mg/l of thidiazuron (TDZ), 73.3 % of the cultures responded with 20.4?±?0.3 somatic embryos (SEs) per 500 mg callus at different stages of development after 6 weeks of culture. The highest response of 86.7 % with 28.3?±?0.5 embryos per 500 mg callus was observed on MS medium supplemented with 2.5 mg/l TDZ and 1.0 mg/l NAA. SEs were encapsulated in calcium alginate beads for the production of synthetic seeds (SSs) and their storability was investigated. The highest SS germination (93.3 %) was observed in 1.0 % sodium alginate followed by 86.7 % germination with 2.5 % sodium alginate. The SSs were stored at three different temperatures (4, 15, and 24?ºC) up to 6 months. The SSs kept at 15 °C showed 64.4 % germinability even after 4 months of storage. Both nonencapsulated and encapsulated SE-derived plants were successfully transferred to soil with 93.3 and 88.3 % survival rate accordingly. Randomly amplified polymorphic DNA (RAPD) analysis revealed that there were no somaclonal variations among the plants produced via somatic embryogenesis and they are true-to-type to their parental plant. These results confirmed the most reliable methods, which can be further used for genetic transformation studies as well as for mass propagation of ornamental D. kirkii at a commercial level.     

Determination of phosphate in freshwater samples by flow-injection with lucigenin chemiluminescence

Lucigenin chemiluminescence (CL) in conjunction with flow-injection analysis (FIA) is used for the determination of phosphate in freshwater samples. The procedure is based on the formation of molybdophosphoric heteropoly acid (MoP–HPA) by the reaction of phosphate and ammonium molybdate under acidic conditions. CL emission was observed as a result of oxidation of lucigenin in aqueous sodium hydroxide solution in the presence of MoP–HPA. Calibration was linear up to 500?µg?L^?1 (r ^2?=?0.9998; n?=?8), with a detection limit (S/N?=?3) of 0.95?µg?L^?1. An injection throughput of 120 h^?1, and relative standard deviation (RSD; n?=?4) of 1.3–3.2% were achieved in the concentration range studied. An on-line chelating column was used to remove interfering cations. The method was applied to freshwater samples, and the results (51?±?1.0 – 107?±?2.0?µg?L^?1) did not differ significantly from results obtained using a spectrophotometric method (52.5?±?1.0 – 102?±?2.0?µg?L^?1) at 95% confidence level (t-test).     

Determination of Cu(II), Fe(III), Mn(II) and Zn(II) in various samples after preconcentration with Rhizopus oryzae loaded natural cellulose (almond bark)

A procedure for the pre-concentration of Cu(II), Fe(III), Mn(II) and Zn(II) is described utilising a minicolumn of natural cellulose (almond bark) modified with fungus (Rhizopus oryzae) prior to their determination by high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS). The optimum pre-concentration conditions such as pH and flow rate for the analytes have been investigated. The analytes were quantitatively retained on the column between pH 6 and 8. Elution was made with 10 mL 1 M HCl solution. Under the optimum conditions, recoveries were found as 97 ± 3%, 96 ± 3%, 98 ± 3% and 94 ± 2% for Cu(II), Fe(III), Mn(II) and Zn(II), respectively, at 95% confidence level. The detection limits obtained from preconcentration of 50 mL of blank solutions (n = 11) were 1.6, 1.8, 2.8 and 1.2 µg L^?1 for Cu(II), Fe(III), Mn(II) and Zn(II), respectively. Relative standard deviations (RSD) of the recoveries for five replicate analyses were lower than 3%. The proposed method was validated by analysing certified reference materials (Peach Leaves SRM 1547 and Fish Tissue IAEA-407). Determination of the Cu(II), Fe(III), Mn(II) and Zn(II) in K?z?l?rmak River water, green beans, beans leave and tomato leaves and fish (Tinca tinca) tissue samples was performed by the proposed method.     

Determination of Nitrite,Phosphate, and Silicate by Valveless Continuous Analysis with a Bubble-Free Flow Cell and Spectrophotometric Detection

A continuous flow analysis system, composed of a 1.2-cm laboratory-made antibubble flow cell and a spectrophotometer, was established. The system was evaluated for the determination of nitrite, phosphate, and silicate. Different from flow injection analysis and other flow analysis modes, an injection or multiposition valve was not needed. Even better, the system was free from interferences from air bubbles without the use of a debubbler device or electronic bubble gate. Without the formation of air bubbles, the chemical reaction was accelerated using a water bath. The experimental parameters for nutrient analysis, including reagent concentration, flow strategy, flow rate, and reaction temperature, were optimized based on a univariate experimental design. The carry-over effect was comprehensively evaluated and may be ignored using this protocol. The established system and analytical methods were especially suitable for laboratories with only basic instruments and limited budgets. The system had the advantages of high sample throughput (>60?h^?1); great convenience without valve utilization; long linear dynamic ranges (0.2–80?µM for nitrite, 0.3–14?µM for phosphate, and 0.5–120?µM for silicate); low detection limits (0.06?µM for nitrite, 0.08?µM for phosphate, and 0.11?µM for silicate); and high recovery values (91.5?±?1.01 to 108.7?±?3.18%). In addition to water samples, national reference materials were analyzed, and the results were in good agreement with the certified values.     

Electroanalytical performance of self-assembled monolayer gold electrode for chloramphenicol determination

Monolayers of 2-mercapto-5-methylbenzimidazole (MMB) were prepared on a polycrystalline gold electrode via a self-assembly process to produce a self-assembled monolayer. The resulting electrode was investigated by cyclic voltammetry and electrochemical impedance spectroscopy, and applied to the determination of chloramphenicol (CAP) in a pharmaceutical formulation using flow injection analysis along with amperometric detection. The amperometric cell was operated at ?0.75 V (vs Ag/AgCl) at a flow rate of 3 mL min^?1. The method was applied to the determination of CAP in ophthalmic solutions, and its performance was compared to a previously validated HPLC method. The response to CAP is linear in the range from 0.050 to 1.000 µmol L^?1 (r?=?0.9990), and the limit of detection is 44 µmol L^?1.     

Rice husk ash nanosilica to inhibit human breast cancer cell line (3T3)

NaOH treatment on phase, purity and particle size of rice husk nanosilica were investigated employing alkaline-extraction–acid-precipitation method. Mild reaction at lower NaOH (1.5 N) revealed small and fine particles (600 nm) due to moderate reaction rate. Morphology of human breast cancer cell line (3T3) revealed that suggestive cell distress effects were more pronounced at 500 µg/ml silica dosages which are in agreement with cell viability decrease (~50 %). Among different silica dosages, 10 µg/ml was found to have highest cell viability (～70 ± 2 %) capable of increasing dissolved oxygen level while viability was almost decreased to 27 ± 5 % due to toxic effect caused at higher SiO₂ dosage and could be a potential candidate best suited for biomedical applications through development of sustainable materials.