Lead telluride nanocrystalline thin films: Structure,optical characterization and a broadband dielectric spectroscopy study

Nanocrystalline PbTe thin films were deposited on a glass substrate by thermal evaporation technique with two thicknesses namely, 45 and 250 nm. The structural studies revealed that the films have nanocrystalline cubic structure and the particle size was found to be 11 and 20.7 nm, for low and high thicknesses respectively. The FE-SEM study shows that the surface grains increase for higher thickness film. This indicates that samples lying under the strong regime of confinement for PbTe thin films. The optical properties confirm the occurrence of confinement process as the optical band gap are 1.67 and 0.9 eV for 45 and 250 nm films, respectively. The dielectric results indicated that the conductivity increases by about two orders of magnitude with increasing the thickness from 45 to 250 nm. Moreover, the permittivity shows a higher dispersion step at lower frequencies in both samples due to the hopping conduction mechanism in addition to the interfacial polarization in such heterogeneous structures. Another small dispersion step is noticed in case of the lower thickness. It is attributed to the polarization of the accumulated charge carriers near the grain boundaries interfaces. No indication of any electrode phenomena in both samples is shown here.     

Thermal stress induced band gap variation of ZnO thin films

The growth temperature and post annealing-dependent optical and structural effect of RF magnetron sputtered ZnO thin films were examined. As the growth temperature increased, the lattice constant increased and approached the bulk value, suggesting a decrease in interfacial strain between the substrate and thin film. For the post annealed samples, the interfacial strain decreased further and was close to the bulk value regardless of the post annealing environments (in air and O₂). The optical properties of all ZnO thin films examined and revealed higher transparency (>90%). Furthermore, the optical band gap varied according to the growth temperature and post annealing environments due to a decrease in the interfacial strain effect.     

Formation of Ge35In8S57 amorphous films for optical applications

Thin films of In-doped Ge-S in the form of Ge₃₅In₈S₅₇ with different film thickness were deposited using an evaporation method. The X-ray diffraction studies demonstrate that the as-prepared films are amorphous in nature for these films. Some optical constants were calculated at a thickness of 150, 300, 450 and 900?nm and annealing temperature of 373, 413, 437 and 513?K. Our optical observations show that the mechanism of the optical transition obeys the indirect transition. It was found that the energy gap, E_g, decreases from 2.44 to 2.20?eV with expanding the thickness of the film from 150 to 900?nm. On the other hand, it was found that E_g increases with annealing temperature from 373 to 513?K. The increment in the band gap can be attributed to the gradual annealing out of the unsaturated bonds delivering a decreasing the density of localized states in the band structure. Using the single oscillator model, the dispersion of the refractive index is described. The dispersion constants of these films were calculated with different both thickness and annealing temperatures. Additionally, both of nonlinear susceptibility, χ⁽³⁾ and nonlinear refractive index, n₂ were calculated.     

Effect of cadmium addition on the optical constants of thermally evaporated amorphous Se–S–Cd thin films

Se₇₅S_25−xCd_x is a promising ternary material, which has received considerable attention due to its applications in the fabrication of various solid state devices. These have distinct advantages, large packing density, mass replication, fast data rate, high signal-to-noise ratio and high immunity to defects. Measurements of optical constants (absorption coefficient, refractive index, extinction coefficient, real and imaginary part of the dielectric constant) have been made on Se₇₅S_25−xCd_x (where x = 0, 2, 4, 6 and 8) thin films of thickness 3000 Å as a function of photon energy in the wave length range 400–1000 nm. It has been found that the optical band gap and extinction coefficient increases while the value refractive index decreases on incorporation of cadmium in Se–S system. The results are interpreted in terms of the change in concentration of localized states due to the shift in Fermi level. Due to the large absorption coefficient and compositional dependence of reflectance, these materials may be suitable for optical disk material.     

Structural and optical properties of pulsed laser deposited SrBi2Nb2O9 thin films

SrBi₂Nb₂O₉ (SBN) thin films were prepared on fused quartz substrates at room temperature by pulsed laser deposition. The influence of deposition parameters such as target-to-substrate distance, oxygen pressure and annealing temperature on film crystallization behavior was investigated by X-ray diffraction. Results indicated that the films grown at the optimum processing conditions have polycrystalline structure with a single layered perovskite phase. The optical transmittance of the films prepared at various oxygen pressures was measured in the wavelength range 200–900 nm using UV–vis spectrophotometer. The results showed that there is a red shift in the optical absorption edge with a rise in the oxygen pressure. Refractive index as a function of wavelength and optical band gap of the films were determined from the optical transmittance spectra. The results indicated that the refractive index increases with increasing oxygen pressure at the same incident light wavelength, while the band gap reduces from 4.13 to 3.88 eV. It may be attributed to an increase in packing density and grain size, and decrease in oxygen defects.     

Low temperature ferromagnetic properties of CdS and CdTe thin films

The magnetic property in a material is induced by the unpaired electrons. This can occur due to defect states which can enhance the magnetic moment and the spin polarization. In this report, CdS and CdTe thin films are grown on FTO glass substrates by chemical bath deposition and close-spaced sublimation, respectively. The magnetic properties, which are introduced from oxygen states, are found in CdS and CdTe thin films. From the hysteresis loop of magnetic moment it is revealed that CdS and CdTe thin films have different kinds of magnetic moments at different temperatures. The M–H curves indicate that from 100 K to 350 K, CdS and CdTe thin films show paramagnetism and diamagnetism, respectively.A superparamagnetic or a weakly ferromagnetic response is found at 5 K. It is also observed from ZFC/FC curves that magnetic moments decrease with temperature increasing. Spin polarized density functional calculation for spin magnetic moment is also carried out.     

Physical properties of vacuum evaporated CdTe thin films with post-deposition thermal annealing

This paper presents the physical properties of vacuum evaporated CdTe thin films with post-deposition thermal annealing. The thin films of thickness 500 nm were grown on glass and indium tin oxide (ITO) coated glass substrates employing thermal vacuum evaporation technique followed by post-deposition thermal annealing at temperature 450 °C. These films were subjected to the X-ray diffraction (XRD),UV-Vis spectrophotometer, source meter and atomic force microscopy (AFM) for structural, optical, electrical and surface morphological analysis respectively. The X-ray diffraction patterns reveal that the films have zinc-blende structure of single cubic phase with preferred orientation (111) and polycrystalline in nature. The crystallographic and optical parameters are calculated and discussed in brief. The optical band gap is found to be 1.62 eV and 1.52 eV for as-grown and annealed films respectively. The I–V characteristics show that the conductivity is decreased for annealed thin films. The AFM studies reveal that the surface roughness is observed to be increased for thermally annealed films.     

近距离升华沉积CdTe掺Cd薄膜的微结构和电学、光学特性

采用近距离升华技术制备了掺杂Cd元素的CdTe多晶薄膜.利用X射线衍射仪和扫描电子显微镜表征其微结构,用霍尔效应测试仪和紫外可见分光光度计分析其电学、光学特性.结果显示,适量的掺杂Cd元素可改善CdTe薄膜晶形,显著提高薄膜的电导特性,由弱的p型电导转变为导电性能良好的n型电导,但对光能隙影响不大. 关键词： 近距离升华 CdTe薄膜 掺杂Cd 电学和光学特性     

Effect of precursors on structure, optical and electrical properties of chemically deposited nanocrystalline ZnO thin films

Nanocrystalline ZnO thin films were chemically deposited on glass substrates using two different precursors namely, zinc sulphate and zinc nitrate. XRD studies confirm that the films are polycrystalline zinc oxide having hexagonal wurtzite structure with crystallite size in the range 25-33 nm. The surface morphology of film prepared using zinc sulphate exhibits agglomeration of small grains throughout the surface with no visible holes or faulty zones, while the film prepared using zinc nitrate shows a porous structure consisting of grains with different sizes separated by empty spaces. The film prepared using zinc sulphate shows higher reflectance due to its larger refractive index which is related to the packing density of grains in the film. Further, the film prepared using zinc sulphate is found to have normal dispersion for the wavelength range 550-750 nm, whereas the film prepared using zinc nitrate has normal dispersion for the wavelength range 450-750 nm. The direct optical band gaps in the two films are estimated to be 3.01 eV and 3.00 eV, respectively. The change in film resistance with temperature has been explained on the basis of two competing processes, viz. thermal excitation of electrons and atmospheric oxygen adsorption, occurring simultaneously. The activation energies of the films in two different regions indicate the presence of two energy levels - one deep and one shallow near the bottom of the conduction band in the bandgap.     

Preparation and characterization of electrodeposited SnS thin films

Tin sulfide (SnS) thin films have been deposited by electrodeposition using potentiostaic method on indium doped tin oxide (ITO) coated glass substrates from aqueous solution containing SnCl₂·2H₂O and Na₂S₂O₃ at various potentials. Good quality thin films were obtained at a cathodic potential −1000 mV versus saturated calomel electrode (SCE). The deposited films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared (FTIR). X-ray diffraction analysis shows that the crystal structure of SnS thin films is orthorhombic with preferential orientation along 〈0 2 1〉 plane. Microstructural parameters such as crystallite size, micro strain, and dislocation density are calculated and found to depend upon cathodic potentials. SEM studies reveal that the SnS films exhibited uniformly distributed grains over the entire surface of the substrate. The optical transmittance studies showed that the direct band gap of SnS is 1.1 eV. FTIR was used to further characterize the SnS films obtained at various potentials.     

Structural characterization of supported nanocrystalline ZnO thin films prepared by dip-coating

Nanocrystalline ZnO thin films prepared by the sol-gel dip-coating technique were characterized by grazing incidence X-ray diffraction (GIXD), atomic force microscopy (AFM), X-ray reflectivity (XR) and grazing incidence small-angle X-ray scattering (GISAXS). The structures of several thin films subjected to (i) isochronous annealing at 350, 450 and 550 °C, and (ii) isothermal annealing at 450 °C during different time periods, were characterized. The studied thin films are composed of ZnO nanocrystals as revealed by analysing several GIXD patterns, from which their average sizes were determined. Thin film thickness and roughness were determined from quantitative analyses of AFM images and XR patterns. The analysis of XR patterns also yielded the average density of the studied films. Our GISAXS study indicates that the studied ZnO thin films contain nanopores with an ellipsoidal shape, and flattened along the direction normal to the substrate surface. The thin film annealed at the highest temperature, T = 550 °C, exhibits higher density and lower thickness and nanoporosity volume fraction, than those annealed at 350 and 450 °C. These results indicate that thermal annealing at the highest temperature (550 °C) induces a noticeable compaction effect on the structure of the studied thin films.     

Electrical and optical properties of ZnO thin films prepared by magnetron rf sputtering—influence of Al, Er and H

The influence of Al, Er and H in ZnO thin films (ZnO:Al, ZnO:Er and ZnO:H) deposited by magnetron sputtering at different substrate temperatures, T_s, on their optical, structural and electrical properties was investigated. X-ray diffraction (XRD) analyses show an improvement of the crystalline structure with increasing T_s. The optical band gap, , of the films, from transmission and reflection spectra, ranged from 3.27 to 3.41 eV. The Urbach band tail width was also calculated. Incorporation of Al and Er resulted in a reduced and an increased resistivity, ρ, respectively, and an increase in the Urbach tail width in both cases. However, sputtering in an Ar+H₂ gas mixture led to an increase in ρ and an improvement in the structural order of the films. A discussion of the influence of T_s and of Al, Er and H on the properties is presented.     

Surface roughness characterization of Al-doped zinc oxide thin films using rapid optical measurement

Transparent conductive oxide thin films have been widely investigated in photoelectric devices such as flat panel display (FPD) and solar cells. Al-doped zinc oxide (AZO) thin films have been widely employed in FPD. Measuring the surface roughness of AZO thin films is important before the manufacturing of photoelectric device using AZO thin films because surface roughness of AZO thin films will significantly affect the performance of photoelectric device. Traditional methods to measure surface roughness of AZO thin films are scanning electron microscopy and atomic force microscopy. The disadvantages of these approaches include long lead time and slow measurement speed. To solve this problem, an optical inspection system for rapid measurement of the surface roughness of AZO thin films is developed in this study. It is found that the incident angle of 60° is a good candidate to measure the surface roughness of AZO thin films. Based on the trend equation y=−3.6483x+2.1409, the surface roughness of AZO thin films (y) can be directly deduced from the peak power density (x) using the optical inspection system developed. The maximum measurement-error rate of the optical inspection system developed is less than 8.7%.The saving in inspection time of the surface roughness of AZO thin films is up to 83%.     

氮分压对氮化铜薄膜结构及光学带隙的影响

在不同的氮分压r(r=N₂/［N₂+Ar］)和射频功率P下，使用反应射频磁控溅射法，在玻璃基片上制备了氮化铜薄膜样品.用台阶仪测得了薄膜的厚度，用原子力显微镜、X射线衍射仪、紫外-可见光谱仪对薄膜的表面形貌、结构及光学性质进行了表征分析.结果表明，薄膜的沉积速率随P和r的增加而增大.薄膜表面致密均匀，晶粒尺寸为30nm左右.随着r的增加，薄膜颗粒增大，且薄膜由(111)晶面转向(100)晶面择优生长.薄膜的光学带隙E_g在1.47—1.82eV之间，随r的增加而增大. 关键词： 氮化铜薄膜 反应射频磁控溅射 晶体结构 光学带隙     

Optical band gap and optical constants in a-Se80Te20−xPbx thin films

The optical constants (absorption coefficient, refractive index, extention coefficient, real and imaginary part of dielectric constant) have been studied for a-Se₈₀Te_20−xPb_x (where x = 0, 2, 6, 10) thin films as a function of photon energy in the wave length range (500–1000 nm). It has been found that the optical band gap increases while the refractive index and the extinction coefficient (k) decreases on incorporation of lead in Se–Te system. The value of absorption coefficient (α) and the extinction coefficient (k) increases, while the value of refractive index (n) decreases with incident photon energy. The results are interpreted in terms of the change in concentration of localized states due to the shift in fermi level.     

Photoluminescence and photoelectrochemical properties of nanocrystalline ZnO thin films synthesized by spray pyrolysis technique

A simple and inexpensive spray pyrolysis technique (SPT) was employed for the synthesis of nanocrystalline zinc oxide (ZnO) thin films onto soda lime glass and tin doped indium oxide (ITO) coated glass substrates at different substrate temperatures ranging from 300 °C to 500 °C. The synthesized films were polycrystalline, with a (0 0 2) preferential growth along c-axis. SEM micrographs revealed the uniform distribution of spherical grains of about 80-90 nm size. The films were transparent with average visible transmittance of 85% having band gap energy 3.25 eV. All the samples exhibit room temperature photoluminescence (PL). A strong ultraviolet (UV) emission at 398 nm with weak green emission centered at 520 nm confirmed the less defect density in the samples. Moreover, the samples are photoelectrochemically active and exhibit the highest photocurrent of 60 μA, a photovoltage of 280 mV and 0.23 fill factor (FF) for the Zn₄₅₀ films in 0.5 M Na₂SO₄ electrolyte, when illuminated under UV light.     

Effect of Er doping on optical band gap energy of TiO2 thin films prepared by spin coating

In order to evaluate the effect of Er doping in the range of 0–1.0 mol% on optical indirect band gap energy (E_g) of the film, the Er-doped TiO₂ (Er-TiO₂) thin films were spin-coated onto fluorine-doped SnO₂ coated (FTO) glasses. Glancing angle X-ray diffraction (GAXRD) results indicated that the films whose thickness was 550 nm consisted of pure anatase and FTO substrate. The anatase (101) TiO₂ peaks became broader and weaker with the rise in Er content. The apparent crystallite size decreased from 12 nm to 10 nm with increasing the amount of Er from 0 mol% to 1.0 mol%. UV–vis spectrophotometry showed that the values of E_g decreased from 3.25 eV to 2.81 eV with the increase of Er doping from 0 to 0.7 mol%, but changed to 2.89 eV when Er content was 1.0 mol%. The reduction in E_g might be attributed to electron and/or hole trapping at the donor and acceptor levels in the TiO₂ band structure.     

Chemical,optical, and electrical characterization of Ga2O3 thin films grown by plasma-enhanced atomic layer deposition

Thin Ga₂O₃ films were grown on Si (100) using trimethylgallium (TMG) and oxygen as the precursors through plasma-enhanced atomic layer deposition. The depositions were made over a temperature range of 80–250?°C with a growth per cycle of around 0.07 nm/cycle. Surface self-saturating growth was obtained with TMG pulse time ≥20?ms?at a temperature of 150?°C. The root mean square surface roughness of the obtained Ga₂O₃ films increased from 0.1?nm to 0.3?nm with increasing the growth temperature. Moreover, the x-ray photoelectron spectroscopy analysis indicated that the obtained film was Ga-rich with the chemical oxidation states Ga³⁺ and Ga¹⁺, and no carbon contamination was detected in the films after Ar⁺ sputtering. The electron density of films measured by x-ray reflectivity varied with the growth temperature, increasing from 4.72 to 5.80?g/cm³. The transmittance of Ga₂O₃ film deposited on a quartz substrate was obtained through ultraviolet visible (UV–Vis) spectroscopy. An obvious absorption in the deep UV region was demonstrated with a wide band gap of 4.6–4.8?eV. The spectroscopic ellipsometry analysis indicated that the average refractive index of the Ga₂O₃ film was 1.91?at 632.8?nm and increased with the growth temperature due to the dense structure of the films. Finally, the I-V and C-V characteristics proved that the Ga₂O₃ films prepared in this work had a low leakage current of 7.2?×?10^?11 A/cm² at 1.0?MV/cm and a high permittivity of 11.9, suitable to be gate dielectric.     

Er3+注入CdTe薄膜的结构和光电性能研究

采用离子注入技术对近距离升华制备的CdTe薄膜进行Er³⁺掺杂研究.讨论了不同掺Er³⁺浓度对CdTe薄膜的结构和光电性能的影响.利用X射线衍射仪、扫描电子显微镜、紫外-可见分光光度计、霍耳效应测试系统和复阻抗分析仪对样品进行测试.结果表明，适当的掺杂量可以改善CdTe薄膜的结晶性能，降低晶界势垒高度，提高其导电性能.在一定掺杂范围内掺Er³⁺对CdTe薄膜的光能隙影响不大. 关键词： CdTe薄膜 离子注入 晶界势垒 光能隙