Evaluating the mobility of toxic metals in untreated industrial wastewater sludge using a BCR sequential extraction procedure and a leaching test

The distribution and speciation of toxic metals in industrial wastewater sludge (IWS) was investigated. In this work, the modified BCR three-stage sequential extraction procedure was applied to the fractionation of Cr Pb Ni, and Cd in untreated industrial wastewater sludge from industrial sites in Hyderabad (Pakistan). The extracts were analyzed using electrothermal atomic absorption spectrometry. The procedure was evaluated using a certified reference material for soil mixed with sewage sludge BCR 483. The results from the partitioning study indicate that more easily mobilized forms (acid exchangeable) of Cd were dominant. The oxidizable fraction was dominant for all four toxic metals. Metal recovery was good, with <4% difference between the total metal recovered through the extractant steps and the total metal determined after microwave digestion. Lixiviation tests (DIN 38414-S4) were used to evaluate the leaching of toxic species from IWS, and it was observed that levels of leachable toxic metals were low compared to the amount of metal extracted in the exchangeable fraction of the BCR protocol.     

Speciation of heavy metals in sewage sludge after mesophilic and thermophilic anaerobic digestion

Two types of sewage sludge anaerobic digestion were carried out: mesophilic and thermophilic. Metal speciation analysis was performed revealing some changes in the chemical form of the metals during the stabilization process of sludge. After both methane fermentation processes, a comparable level of organic matter distribution was obtained (≈ 40 %). The amount of produced methane during thermophilic and mesophilic digestion was 560 mL of CH4 and 580 mL of CH₄ from 1 g of removed organic matter, respectively. Low concentration of heavy metal ions in the liquid phase of sludge was observed. Metal ions precipitated and remained bound throughout the stabilization process. No accumulation of heavy metals in the mobile fractions of sludge (exchangeable and carbonate) was observed for either digestion process. The highest increase of zinc, copper, nickel, cadmium, and chromium concentration was observed in the organic-sulfide fraction, whereas the highest increase of lead was found in the residual fraction.     

Investigation of heavy metals mobility in shrimp aquaculture sludge—Comparison of two sequential extraction procedures

Influence of heavy metals was investigated by conducting various tests on the samples collected from aquaculture shrimp in Selangor, Malaysia. The concentration of heavy metals in the sludge and potential of mobility based on its association forms was studied. Two sequential extraction methods (five stages Tessier method and three steps BCR method) were used to determine the binding forms of the metals.From the analysis, Ca, Fe and Mn were found to be highest concentrated metals compared to Zn, Cu, Cr, Cd and Pb in aquaculture shrimp sludge. From the sequential extraction, Cd, Mn and Pb were mostly found in exchangeable/carbonate form, showed its susceptibility to be leached easily. Also Cu and Zn were extracted predominantly in oxidizable form. All metal concentrations (except Cd, Zn and Cu) were extracted to be higher in residual fraction in this method. The results of BCR method are totally similar to the five stages Tessier method. By comparing the percent of recovery, the BCR method was better than Tessier method. Nevertheless for both methods the percent of their recoveries were acceptable. For Pseudototal metal digestion, although the concentration of Cd is less than other heavy metals, it is very harmful as a fertilizer because Cd is one of the heavy metals that might be in the leaf or fruit of plants. Also for investigation of Ca in the sludge, this element was measured and high amounts of that show sludge is useful for growing of plant. The results of direct digestion of heavy metals show that with the control of Cd in this sludge we can use this sludge as fertilizer in soils for agriculture but it is better if it is used for fruitless plants.     

Determination of Trace Metal Species in the Suspended Matter of Riverine and Estuarine Waters

A sequential extraction technique was used to determine the chemical species of six metals (Fe, Mn, Cu, Zn, Pb, Cd) in suspended matter of the Kaoping and Tsengwen river basins. The samples were taken to cover the fresh and marine characteristics. The precision of the species determination was estimated by the relative difference between the concentration of total metal and the sum concentation of the five species. The accuracy for the measurement of total metal was examined from the recovery of metal spiking. The accuracy of the total determination is better than 94% and the precision of speciation is greater than 90%. Most of the studied metals were found in the Fe-Mn oxides and residual fractions except that Cd, Zn and Cu have significant amounts in the exchangeable, carbonate, and organic matter phases, respectively. Species other than residual fraction are generally considered as potentially available for biota in aquatic systems, and in most cases, metal pollution could be reflected from the variation of fraction distributions.     

污水厂污泥堆肥后重金属形态变化分析

采用高温好氧静态强制通风堆肥工艺,研究了污水厂污泥与稻草、锯末、粉煤灰、磷矿粉、石灰按不同比例混合堆肥前后重金属在交换态、碳酸盐结合态、铁锰氧化物结合态3种不稳定态和包括有机结合态、残渣态的稳定态含量的变化。结果表明,该试验可以显著降低污泥中交换态Cu、Pb、Zn、Cd和As的含量,提高其它形态的含量。由此可见,堆肥处理可以在一定程度上降低重金属活性并保持养分,从而达到农业利用的目的。     

贵阳污灌区菜地土壤团聚体中有机碳和重金属的含量特征及相关性分析

以贵阳某污灌区菜地土壤为研究对象,分别采用微波消解-电感耦合等离子体质谱(ICP-MS)法和水合热重铬酸钾氧化分光光度法分析不同粒径土壤团聚体中重金属和有机碳的含量特征,并对有机碳和重金属的相关性进行分析。结果表明,以2mm粒径团聚体的含量为最高,约占75%。Cu、Zn、Cd和Pb在0.25～0.5mm粒径团聚体中含量最高,Cr在5～8mm粒径团聚体中含量最高,As在不同粒径团聚体中的含量变化不大,重金属含量随土层深度增大而减小。土壤重金属富集因子表现为CuPbCdZnCrAs,Cu、Zn、Cd和Pb在0.25～0.5mm粒径团聚体中分布因子最高,而在5～8mm粒径团聚体中重金属的质量负载因子最大。土壤有机碳含量随团聚体粒径的增大表现为先增大后减小,不同粒径团聚体中Cu、Cd、Pb和As含量与有机碳含量均呈显著正相关(p0.05)。污灌区菜地土壤Cr、As在5～8mm粒径团聚体中富集现象显著,Cu、Zn、Cd、Pb在0.25～0.5mm粒径团聚体中均表现出显著的富集特征。6种重金属在5～8mm粒径团聚体中的质量负载因子均为最高,表明6种重金属在5～8mm粒径团聚体中的贡献最大。     

Application of Short Sequential Extraction Procedure（SSEP） for the Determination of Zn, Cu, and Cd Contents in Riverbed Sludge in Hejiagou, Harbin, China

IntroductionThe environment is contaminated by high concen-trations of metals from different sources such as conta-minated soils[1—10], sediments[11—15], and sewage orindustrial sludge[16—20]. However, there has been noreport on the determination of he…     

Chemical Aspects of Heavy Metal Solubility with Reference to Sewage Sludge Amended Soils

Abstract

The long term benefits of applications of sewage sludges to land as an alternative source for plant nutrients are frequently limited by potentially toxic contents of heavy metals. While upper limits for metal contents in amended soils have been defined in both North America and Europe, there has been little attention paid to the fate of the metals if soil management practices are changed and the solubility and hence the mobility of the metals increased. This study investigated the role of changes in pH and additions of chloride ions to the content of soluble Cd, Co, Cr, Cu, Pb, Ni, V and Zn in soils to which sewage sludge had been applied. The contents of soluble metals ranged from less than 1 μmol L^?1 for V to 500 μmol L^?1 for Zn. For all the metals, contents were greater in the presence of Cl^? ions and increased markedly as the pH decreased below about pH 5. Contents of V, Cr, Cu and Pb increased at pH's above 7. As all metal contents were undersaturated with respect to hydroxide or carbonate precipitates, the changes in their contents were probably related to desorption from variable charge sites on mineral and/or humic surfaces.     

Heavy metal in sediments and bioaccumulation in the bivalve Corbula gibba in a drilling discharge area

The longterm bioavailability of heavy metals in sediments of a Northern Adriatic Sea shelf area affected by drilling mud and cutting discharges was discussed. Levels of Mn, Cu, Cr, Zn and Pb in different geochemical phases of the sediment and in soft tissues of the bivalve Corbula gibba were recorded and the relationships between biological and geochemical metal investigated. Total metal content, acetic acid extractable-, exchangeable-, carbonate-, easily reducible-, moderately reducible-, oxidable- and residual-fractions were determined on sediment samples. Corbula gibba was collected from wet sediments at the same times and sites, and the soft-tissue metal contents were determined. Correlations show that the fractions with greatest bioavailability are the exchangeable and carbonate for Cr and the exchangeable, carbonate, easily and moderately reducible fractions for Zn. Data also show a possible bioavailability of Pb only from the residual fraction, consisting of very resistant matter of more recent anthropogenic origin. Near the platform, total Mn content in sediments and in C. gibba tissues show a strong correlation suggesting that this organism is sensitive to variations of the Mn-oxi-hydroxides superficial film. No relationships were found between biological and sediment-bound Cu, however the discharged muds did not cause Cu enrichment. The metal fraction determined by weak acetic acid extraction at no point seems related to metal levels in Corbula gibba.     

Evaluation of heavy metal bioavailability in soil amended with poultry manure using single and BCR sequential extractions

In the present study, three-step Community Bureau of Reference sequential extraction scheme (BCR-SES) and single extraction methods were performed to assess the mobility and availability of heavy metals (Cd, Cu, Pb, Fe and Zn) in an agricultural soil before and after amendment with poultry waste (PW).The PW samples were collected from poultry farms, situated in Hyderabad Sindh, Pakistan. The extractable heavy metals were measured by flame and electrothermal atomic absorption spectrometry. The validation of the method was carried out by analysis of a certified reference material of soil amended with sewage sludge (BCR-483). The single extractions using calcium chloride and EDTA, separately, while BCR-SESs were developed to evaluate the available heavy metals to plants and their environmental accessibility for control soil (CS), PW and soil amended with PW (SPW).The pH of the PW and SPW were found to be < 6.0, which may enhance the leaching of heavy metals to agricultural soil. The results from the partitioning study indicated that easily mobilised forms (acid exchangeable) of Cd were higher than other heavy metals. The oxidisable fractions of all heavy metals were dominant in PW and SPW as compared to found in CS samples. The EDTA- and CaCl₂-extractable heavy metals correspond to 5.0 to 10 and 0.5 to 3.0%, respectively of total contents in all three solid samples. Contamination factors revealed that the retention of Pb and Zn were higher compared with Cu, Cd and Fe in CS, PW and SPW samples.     

Determination of the total content and distribution of cadmium,copper and zinc in human parotid saliva

The contents of cadmium, copper and zinc, and the distribution of these metals among the protein fractions of human parotid saliva were determined by atomic absorption spectrometry. The proteins were separated by gel filtration. The contents of metal were found to be 3.5 ppb Cd, 88 ppb Cu and 49 ppb Zn. In the protein fractions, zinc was distributed over a wide range, the highest contents being found in proteins of high molecular weight. Cadmium was found in the fractions which contained the largest amounts of zinc. Copper was present in a relatively narrow range of proteins of intermediate molecular weight.     

耐高盐碱蓬对湿地土壤中金属元素的富集特征研究

基于秦皇岛滨海湿地人工种植耐高盐碱蓬修复工程试验,通过分析湿地土壤沉积物及耐高盐碱蓬中不同金属元素的含量与变化,研究了耐高盐碱蓬对金属元素的富集特征。结果显示:湿地沉积物中Fe、Mn、Cr、Pb和Zn的浓度较高,分别为8 210. 94、110. 04、8. 78、8. 25、10. 95 mg/kg,Cd的浓度最低,平均值为0. 022 mg/kg,湿地试验区土壤中同一金属元素变异程度较小,分布较均匀。碱蓬体内重金属含量根据采集地点的不同有差异,但与各站位中土壤的重金属分布特征存在正相关性;其中碱蓬内Fe、Mn、Zn、Cu的平均含量相对较高,且Fe、Mn、Ni、Cu、As、Cd、Pb元素在碱蓬根中的平均含量高于茎叶,而Cr在茎中的平均含量最高,Zn和Mo在叶中的含量最高。碱蓬的根、茎、叶对Cd的富集效果最好,其次为Mo、Cu,对Fe、Mn、Zn、As和Pb的富集效果相对较差,说明碱蓬对沉积物中不同金属元素的富集移出率存在差异。金属元素在碱蓬中的转移系数研究表明,Mo、Zn、Cd和Mn等元素可由根部转移到叶中,而Fe、Ni、Pb、As和Cu等金属元素固定在根部,该研究可为利用碱蓬修复湿地重金属污染提供理论基础。     

Distribution of heavy metals of agricultural soils of central Greece using the modified BCR sequential extraction method

The state of heavy metal (Cd, Cu, Ni, Zn, Pb, and Cr) pollution was studied, in 440 texturally different soil profiles in Thessaly, an intensely cultivated region in Central Greece. The study was carried out in 2004 and 2005 on 220 soil samples for each year. Soil samples were classified in three soil orders: Endisols, Alfisols, and Vertisols according to the Soil Taxonomy System. The pseudo-total concentrations of heavy metals were determined by the aqua regia procedure. Heavy metals were also determined after division into four fractions by sequential extraction with (a) acetic acid (exchangeable and specifically adsorbed metals), (b) a reducing agent (bound to Fe/Mn hydroxides), (c) an oxidizing agent (bound to soil organic matter), and (d) aqua regia (bound to mineral structures, residual). The concentrations of all the metals studied were higher in the topsoil (0–30?cm) and lower in the second soil layer (30–60?cm). Concentrations of 70–82% of Cd, 39–64% of Cu, 41–69% of Ni, 29–51% of Zn, 75–89% of Pb, and 52–87% of Cr were found in the first two fractions. Cd appeared to be the most mobile of the metals studied, while Cu and Zn were found in forms associated with soil organic matter. The chemical partitioning patterns of Pb and Cr indicated that these metals are largely associated with the Fe–Mn hydroxides, while Cr was also found in the residual fractions. Significant correlations between heavy metals fractions and soil physicochemical parameters were obtained and discussed.     

大庆地区城市污泥中重金属元素含量水平调查与分析

采用原子吸收光谱法和原子荧光光谱法测定了大庆市四座生活污水处理厂污泥中重金属元素含量,平行测定的相对标准偏差在1.6%~4.6%,加标回收率在93.6%~102.1%,表明方法的精密度和准确度都较好,四个污水处理厂污泥中重金属总量大小依次为ZnCuCrPbNiCd,锌的含量高可能与城市排水管道大多采用镀锌材料以及锌的理化性质有关。将其含量水平与标准比较发现:大庆城市污泥中重金属含量水平不高,完全符合《农用污泥中污染物控制标准》的重金属标准,为城市污泥处理、处置和环境管理提供可靠的数据支持。     

Persistence of Metal Residues in Sewage Sludge Treated Soils Over Seventeen Years

Abstract

Results from two long-term sewage sludge experiments conducted on different soil types are presented. Sewage sludges highly contaminated with Cr, Cu, Ni or Zn and a relatively uncontaminated sludge were applied at both sites at the same rates and metal contents in 1968. The Cr-rich sludge also had a high Cd content. Plot soils were sampled in 1972, 1976 or 1977, 1981 and 1985 and total and extractable metal contents determined. Metals added in sewage sludge may change their form but persist in soils in an extractable and plant available form for many years. There is little difference in soil extractable contents or plant uptake of Cu and Zn whether sludge is applied as one single application or as its equivalent in four separate annual applications of one quarter the amount. The percentages of the total chromium contents extractable by both EDTA and acetic acid were small and this was reflected in a low uptake of this element by pasture herbage species (<0.3 mg Cr/kg DM).     

Chemical characterisation of biosludge from a wastewater treatment plant in a neutral sulphite semi-chemical pulp mill by single and sequential extraction of heavy metals and micro-/macronutrients — a case study

The main impetus for utilising the biosludge from the neutral sulphite semi-chemical pulping process is the Finnish legislation which from 1st January 2016 prohibits the deposition of this residue in landfills in Finland. The dry matter content of the biosludge in this case study was low (12.1 mass %), meaning that incineration of this residue is uneconomical. The biosludge was rich in P (6260 mg kg^?1). This, together with the high total organic carbon value of 459 g kg^?1 and the metal concentrations (As, Cd, Cr, Cu, Ni, Pb, Zn and Hg) lower than the Finnish permissible limits for land application, supports wide and various end-uses for this residue. Except for S (27600 mg kg^?1) and Cd (1.4 mg kg^?1), the other heavy metal concentrations in the biosludge were lower than the maximum values for heavy metal concentrations in a non-contaminated soil referred to the literature. From the utilisation perspective, and in view of the high levels of S and Na, this residue could efficiently be used, for example, to landscape landfills.     

桦甸油页岩中稀土元素赋存状态研究

以吉林省桦甸油页岩为研究对象,采用电感耦合等离子质谱( ICP-MS)和化学逐级提取方法相结合,对油页岩中稀土元素的分布特征以及油页岩中稀土元素的赋存状态进行研究.结果表明,相对于中国煤,桦甸油页岩表现为轻稀土元素富集程度高于重稀土元素.油页岩中稀土元素与陆源碎屑岩关系密切,且陆源物质的供应相对比较稳定.轻重稀土间分馏...     

Comparison between conventional and ultrasound accelerated Tessier sequential extraction schemes for metal fractionation in sewage sludge

Chemical sequential extraction for metal fractionation in sewage sludge using the Tessier method has been accelerated by ultrasound. The two sequential extraction schemes (conventional and ultrasound accelerated) were compared in terms of extraction efficiency, precision, treatment time and partitioning patterns of metals. Extractable contents of Cu, Cr, Ni, Pb and Zn were measured by flame atomic absorption spectrometry, and the analytical results obtained by the two procedures were statistically compared (P = 0.95). No significant differences were found in the two first fractions (i.e. exchangeable and carbonate-bound), however, in the third and fourth extracts (i.e. Fe-Mn oxides-bound and organic matter-bound) the extraction capability of the two methods differed significantly. Received: 15 June 1998 / Revised: 10 November 1998 / Accepted: 11 November 1998     

Comparison between conventional and ultrasound accelerated Tessier sequential extraction schemes for metal fractionation in sewage sludge

Chemical sequential extraction for metal fractionation in sewage sludge using the Tessier method has been accelerated by ultrasound. The two sequential extraction schemes (conventional and ultrasound accelerated) were compared in terms of extraction efficiency, precision, treatment time and partitioning patterns of metals. Extractable contents of Cu, Cr, Ni, Pb and Zn were measured by flame atomic absorption spectrometry, and the analytical results obtained by the two procedures were statistically compared (P = 0.95). No significant differences were found in the two first fractions (i.e. exchangeable and carbonate-bound), however, in the third and fourth extracts (i.e. Fe-Mn oxides-bound and organic matter-bound) the extraction capability of the two methods differed significantly. Received: 15 June 1998 / Revised: 10 November 1998 / Accepted: 11 November 1998     

Sedimentation pattern and sediments bioavailability in a wastewater discharging area by sequential metal analysis

Atomic absorption spectrometry was applied to investigate sedimentation pattern and sediments bioavailable phase (BAP) at 41 sites of a wastewater discharging area. The position of sampling sites was confirmed by the aid of a global positioning system (GPS). Contaminants discharged from a large wastewater plant are dispersed to the inner bay and the coastal line rather than the outer bay and the center waterway. The fractional composition of sediment Zn in the discharging area accounted for the presence of exchangeable 239 mg/kg (35.1%)>reducible 163 mg/kg (24.0%)>carbonate 149 mg/kg (22.0%)>residual 98 mg/kg (14.4%)>organic 31 mg/kg (4.6%) in sediment layers of 0–2 cm. However, the order was changed in layers of 15–20 cm as residual>reducible>organic>carbonate>exchangeable. The most abundant fraction of sediment Cu and Fe was organic Cu and residual Fe, respectively. The content of BAP in sediments are quite different with respect to metal species and sediment layer analyzed. It is obvious that sequential metal analysis is a useful tool in understanding dispersion of sediments and sedimentation patterns.