Iron analysis in atmospheric water samples by atomic absorption spectroscopy (AAS) in water–methanol

To distinguish between Fe(II) and Fe(III) species in atmospheric water samples, we have adapted an analytical procedure based on the formation of a specific complex between Fe(II) and ferrozine (FZ) on a chromatographic column. After elution of Fe(III), the Fe(II) complex is recovered with water–methanol (4:1). The possibility of trace iron measurements in this complex medium by graphite-furnace atomic-absorption spectrometry has been investigated. A simplex optimization routine was required to complete the development of the analytical method.     

Ionic liquid–water mixtures as solvents for poly(N-vinylimidazole)

Ionic liquids extend the Hofmeister series and create a wide range of new possibilities for processes involving salt effects on both soluble and crosslinked systems. This work reports on some mixtures of water with NaCl or an ionic liquid, either 1-ethyl-3-methylimidazolium tosylate or 1-hexyl-3-methylimidazolium chloride, which are better solvents for linear poly(N-vinylimidazole) (L-PVI) than water, i.e., that exhibit a salting-in effect. The intensity of the salt effects was measured on the basis of the polymer solubility, the decrease in polymer–solvent interaction parameter (measured by light scattering), and the increase of coil size (measured through the intrinsic viscosity). It was thus found that the intensity of the salting-in effect of either NaCl or 1-hexyl-3-methylimidazolium chloride on L-PVI is different (larger for the ionic liquid), which denotes that salt effects are not under anion control, and the mechanisms operating in the linear and crosslinked polymers are different. These results are discussed after accounting for the role of ion–polymer interactions.     

Solvent effects on the kinetics of solvolysis of trans-dichlorobis (N-methylethylenediamine)cobalt(III) ion in water–propan-2-ol and water–acetonitrile mixtures

First order solvolysis rates of the trans-dichlorobis (N-methylethylenediamine) cobalt(III) ion have been measured over a wide range of solvent compositions and temperatures in water–propan-2-ol and water–acetonitrile mixtures. The rate of solvolysis is faster in the former mixtures rather than the latter. Plots of log(rate constant) versus the reciprocal of the dielectric constant of the co-solvent, and also versus the Grunwald–Winstein Y-values are non-linear for both co-solvents; this non-linearity is derived from a large differential effect of solvent structure between the initial and transition states. However, extrema in the variation of enthalpy H and entropy S of activation correlate well with the extrema in physical properties of the mixtures which are related to changes in solvent structure. Linear plots of H versus S were obtained and the isokinetic temperature indicates that the reaction is entropy controlled. The application of a free-energy cycle shows that changes in solvent structure affect the pentacoordinated cobalt(III) ion in the transition state more than the hexacoordinated cobalt(III) ion in the initial state. In addition, the stabilizing influence of changes in solvent structure is greater in propan-2-ol–water mixtures than in acetonitrile–water mixtures, and the difference becomes greater as the mole fraction, x2 of the organic co-solvent increases.     

Kinetics of aquation of trans-dichlorobis(N,N′-dimethylethylenediamine)cobalt(III) ion in water–methanol in water–propan-2-ol media

The complex trans-[Co(dmen)2Cl2]Cl (dmen=N,N-dimethylethylenediamine) has been prepared and characterized by elemental analysis, u.v.-vis. and i.r. spectra. The kinetics of the primary aquation of trans-[Co(dmen)2Cl2] in H2O, H2O–MeOH and H2O–i-PrOH have been examined over a wide range of solvent compositions and temperatures (40–55°C). Plots of rate constants (log k) versus the reciprocal of the dielectric constant of the medium (Ds–1) and Grunwald–Winstein values of the solvent (Y) were found to be non-linear. The variation of enthalpies (H) and entropies (S) of activation with solvent composition has been determined. Plots of H or S versus the mole fraction of each solvent exhibit extrema at x2=ca. 0.16 and 0.27 for MeOH and at x2=ca. 0.03 and 0.14 for i-PrOH. Furthermore, the cycle relating the free energy of activation in H2O to that in H2O–co-solvent shows that the stabilizing influence of the changes in the solvent structure is greater on the emergent five-coordinate cation in the transition state than that on the complex ion in the initial state, with the difference becoming greater as the mole fraction of the co-solvent increases.     

Intramolecular Rearrangements of >Si(O–C·=O)(CH2–CH3) and >Si(CH2–CH·–CH3)(CH2–CH3) Radicals

Using ESR and IR spectroscopy, the structures of >Si(O–C^·=O)(CH₂–CH₃) (1) and >Si(CH₂–CH^·–CH₃)(CH₂–CH₃) (2) radicals were deciphered. The directions and kinetic parameters of reactions of intramolecular rearrangements in these radicals were determined. The reactions of hydrogen atom abstraction in radical (1) from the CH₂ and CH₃ groups were studied. It was found that the endothermic reaction of hydrogen atom abstraction from the methyl group occurs at a higher rate than the exothermic reaction with the methylene group. The differences are determined by changes in the size of a cyclic transition state. Based on the experimental data, the strengths of separate C–H bonds in surface fragments are compared. The rearrangement >Si(CH₂–CH^·–CH₃)(CH₂–CH₃) >Si(C^·(CH₃)₂)(CH₂–CH₃) was discovered and its mechanism was determined. One of its steps is the skeletal isomerization Si- (2)- _. (1)Si- (1)- _. (2). Experimental data are analyzed using the results of quantum-chemical calculations of model systems.     

Bubble points of hydrogen chloride–water–isopropanol and hydrogen chloride–water–isopropanol–benzene systems and liquid–liquid equilibria of hydrogen chloride–water–benzene and hydrogen chloride–water–isopropanol–benzene systems

Bubble points of the HCl–water–isopropanol and the HCl–water–isopropanol–benzene systems and liquid–liquid equilibria (LLE) of the HCl–water–benzene and the HCl–water– isopropanol–benzene systems were measured at 25–85°C and 30–70°C, respectively. The electrolyte nonrandom two-liquid model proposed by Chen et al. [C.-C. Chen, H.I. Britt, J.F. Boston, L.B. Evans, AIChE J. 28 (1982) 588–596] can satisfactorily correlate bubble points and liquid–liquid equilibria of the present mixed-solvent electrolyte systems over the entire range of temperature and concentrations using only binary adjustable parameters.     

A structural and Mössbauer study of complexes with Fe(2)(micro-O(H))(2) cores: stepwise oxidation from Fe(II)(micro-OH)(2)Fe(II) through Fe(II)(micro-OH)(2)Fe(III) to Fe(III)(micro-O)(micro-OH)Fe(III)

Dinuclear non-heme iron clusters containing oxo, hydroxo, or carboxylato bridges are found in a number of enzymes involved in O(2) metabolism such as methane monooxygenase, ribonucleotide reductase, and fatty acid desaturases. Efforts to model structural and/or functional features of the protein-bound clusters have prompted the preparation and study of complexes that contain Fe(micro-O(H))(2)Fe cores. Here we report the structures and spectroscopic properties of a family of diiron complexes with the same tetradentate N4 ligand in one ligand topology, namely [(alpha-BPMCN)(2)Fe(II)(2)(micro-OH)(2)](CF(3)SO(3))(2) (1), [(alpha-BPMCN)(2)Fe(II)Fe(III)(micro-OH)(2)](CF(3)SO(3))(3) (2), and [(alpha-BPMCN)(2)Fe(III)(2)(micro-O)(micro-OH)](CF(3)SO(3))(3) (3) (BPMCN = N,N'-dimethyl-N,N'-bis(2-pyridylmethyl)-trans-1,2-diaminocyclohexane). Stepwise one-electron oxidations of 1 to 2 and then to 3 demonstrate the versatility of the Fe(micro-O(H))(2)Fe diamond core to support a number of oxidation states with little structural rearrangement. Insight into the electronic structure of 1, 2', and 3 has been obtained from a detailed M?ssbauer investigation (2' differs from 2 in having a different complement of counterions). Mixed-valence complex 2' is ferromagnetically coupled, with J = -15 +/- 5 cm(-)(1) (H = JS(1).S(2)). For the S = (9)/(2) ground multiplet we have determined the zero-field splitting parameter, D(9/2) = -1.5 +/- 0.1 cm(-)(1), and the hyperfine parameters of the ferric and ferrous sites. For T < 12 K, the S = (9)/(2) multiplet has uncommon relaxation behavior. Thus, M(S) = -(9)/(2) <--> M(S) = +(9)/(2) ground state transition is slow while deltaM(S) = +/-1 transitions between equally signed M(S) levels are fast on the time scale of M?ssbauer spectroscopy. Below 100 K, complex 2' is trapped in the Fe(1)(III)Fe(2)(II) ground state; above this temperature, it exhibits thermally assisted electron hopping into the state Fe(1)(II)Fe(2)(III). The temperature dependence of the isomer shifts was corrected for second-order Doppler shift, obtained from the study of diferrous 1. The resultant true shifts were analyzed in a two-state hopping model. The diferric complex 3 is antiferromagnetically coupled with J = 90 +/- 15 cm(-)(1), estimated from a variable-temperature M?ssbauer analysis.     

Bulk properties and hydration numbers of components of water–salt,water–urea,and water–urea–salt systems

With an increase in the concentration of additives, the hydration numbers of compounds decrease. Thus, in a saturated 54.6% solution, urea loses approximately 3/4 of the initial amount of water, forming an aquacomplex of the composition (NH₂)₂CO?H₂O. In a supersaturated 44% solution, the sodium chloride aquacomplex is dehydrated by 2/3, and in a supersaturated 67% solution, sodium sulfate is dehydrated by 5/6. The density of these solutions is 1.354÷1.360 g/cm³ (44% NaCl) and 1.800÷1.849 g/cm³ (67% Na₂SO₄). In a saturated urea solution, NaNO₃, NaCl, and Na₂SO₄ complexes lose 53÷55% of hydration water. It is shown that the interactions in the binary water–urea system somewhat increase the hydration number of the salts (structural hydration). The hydration water density, a structurally important characteristic, increases in the series of solutions of urea, NaNO₃, NaCl, and Na₂SO₄. In the same series of additives, the excess volume of binary water–urea and water–salt systems becomes more negative.     

Ni(COD)(DQ): An Air-Stable 18-Electron Nickel(0)–Olefin Precatalyst

We report that Ni(COD)(DQ) (COD=1,5-cyclooctadiene, DQ=duroquinone), an air-stable 18-electron complex originally described by Schrauzer in 1962, is a competent precatalyst for a variety of nickel-catalyzed synthetic methods from the literature. Due to its apparent stability, use of Ni(COD)(DQ) as a precatalyst allows reactions to be conveniently performed without use of an inert-atmosphere glovebox, as demonstrated across several case studies.     

Surface tension isotherms of the dioxane–acetone–water and glycerol–ethanol–water ternary systems

The results of the experimental and theoretical studies of the concentration dependence of surface tension of aqueous solutions of the 1,4-dioxane–acetone–water and glycerol–ethanol–water ternary systems were given. The studies were performed by the hanging-drop method on a DSA100 tensiometer. The maximum error of surface tension was 1%. The theoretical models for calculating the surface tension of the ternary systems of organic solutions were analyzed.     

Suzuki–Miyaura cross-coupling reactions in water using in situ generated palladium(II)–phosphazane complexes

The phosphazane derivatives(L1–3) were readily obtained by reaction of different ratios of PCl3 and PhNH2. The L1–3 derivatives were found to be efficient ligands in the palladium-catalyzed Suzuki C–C coupling reactions in water. It was determined that with the use of L1–3 /Pd(OAc)2 system as a catalyst, aryl halides undergo Suzuki cross-couplings with arylboronic acids to give the desired products in moderate to excellent yields.     

Is [Co(4)(H(2)O)(2)(α-PW(9)O(34))(2)](10-) a genuine molecular catalyst in photochemical water oxidation? Answers from time-resolved hole scavenging experiments

Water oxidation catalysts: evolution of [Co(4)(H(2)O)(2)(α-PW(9)O(34))(2)](10-) to catalytically active species is assessed by laser flash photolysis in sacrificial photocatalytic cycles with Ru(bpy)(3)(2+) as a photosensitizer.     

SO2–ethanol–water (SEW) fractionation process: production of dissolving pulp from spruce

SO₂–ethanol–water (SEW) fractionation process is a highly attractive platform for future lignocellulosic Biorefineries. Its governing advantages include high flexibility in the selection of the raw material, simple and efficient recovery of fractionation chemicals, absence of carbohydrate degradation (both cellulose and hemicelluloses), and high reaction rates. The process is suitable for production of various carbohydrate- and lignin-based products including papermaking pulp, glucose, bioalcohols and lignosulfonates. The present paper addresses the possibility of producing dissolving pulp from spruce using SEW fractionation followed by ECF bleaching with and without hot caustic extraction. Comprehensive characterisation of chemical and macromolecular properties of the SEW dissolving pulps was complemented by determining the quality of viscose. The comparison with conventional viscose-grade acid sulfite pulps revealed close proximity in all properties. Therefore, considering the advantages of SEW process, it is suggested as a possible replacement for acid sulfite process in dissolving pulp manufacturing.     

Poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene)oxide triblock copolymers at the water/air interface and in foam films

The behavior of commercial poly(ethylene oxide)(PEO)–poly(propylene oxide)(PPO)–PEO triblock copolymers at the water/air interface and in microscopic foam films is studied. In aqueous solution these amphiphilic nonionic substances exhibit a surfactant-like aggregation and adsorption behavior. Even below the critical micelle concentration (cmc) the surface concentration is so high that the PEO chains are squeezed and protrude into the solution in order to accommodate to the situation at the interface. As evidenced by measurements of the ellipticity of light reflected from the free surface of the solution a PEO brush is created at the fluid interface. The microscopic foam film is used as a tool for investigating the normal interaction between two PEO brushes facing each other. Stable foam films are obtained at concentrations below the cmc and steric repulsion predominates (in 0.1 M NaCl). A brush-to-brush contact is established only at higher capillary pressures and the disjoining pressure isotherm follows de Gennes' scaling prediction. At lower pressure a softer steric repulsion occurs. It is governed by the bulk copolymer concentration and hence is fundamentally different from the brush-to-brush repellency. On the whole PEO–PPO–PEO copolymers behave as nonionic surfactants, but the large size of their molecules exemplifies the excluded-volume features. Received: 13 July 1999/Accepted: 27 July 1999     

Seeded growth core-shell (Ag–Au–Pd) ternary nanostructure at room temperature for potential water treatment

Seed-mediated growth is a promising technique for preparation of multi-metallic nanostructures, in which reduction of metal ions takes a place over the surface of another one. Herein, a seed growth mechanism was investigated for synthesis of core-shell Ag–Au–Pd ternary nanostructures through a facile method at room temperature. Ascorbic acid and sodium alginate were used as nano-generator and stabilizing agent, respectively. Spherical shaped monocular Ag nanostructure with size of 13.6 nm grew to 24.4 nm of Ag–Au binary and to 58.8 nm of Ag–Au–Pd ternary core-shell nanostructures. The crystalline shape of nanostructures was approved by X-Ray diffraction analyses. While, FT-IR data approved the redox mechanism for synthesis the as-required nanostructures. The catalytic reactivity of the prepared nanostructures in reductive degradation of methylene blue dye was studied. The results approved the role of Pd in perfection of catalytic degradation of the as-tested dye. The rate constant of dye degradation was considerably enlarged from 62.1 × 10⁻³ m⁻¹ for Ag monocular nanostructures to 403.3 × 10⁻³ m⁻¹ for Ag–Pd binary and to 852.4 × 10⁻³ m⁻¹ for Ag–Au–Pd ternary core-shell nanostructures. The obtained results offer an energy saving method to fabricate core-shell catalytically active ternary nanostructures with promising applicability in water treatment.     

Accurate predictions of water cluster formation, (H₂O)(n=2-10)

An efficient mixed molecular dynamics/quantum mechanics model has been applied to the water cluster system. The use of the MP2 method and correlation consistent basis sets, with appropriate correction for BSSE, allows for the accurate calculation of electronic and free energies for the formation of clusters of 2-10 water molecules. This approach reveals new low energy conformers for (H(2)O)(n=7,9,10). The water heptamer conformers comprise five different structural motifs ranging from a three-dimensional prism to a quasi-planar book structure. A prism-like structure is favored energetically at low temperatures, but a chair-like structure is the global Gibbs free energy minimum past 200 K. The water nonamers exhibit less complexity with all the low energy structures shaped like a prism. The decamer has 30 conformers that are within 2 kcal/mol of the Gibbs free energy minimum structure at 298 K. These structures are categorized into four conformer classes, and a pentagonal prism is the most stable structure from 0 to 320 K. Results can be used as benchmark values for empirical water models and density functionals, and the method can be applied to larger water clusters.     

Composite poly(vinyl alcohol)–poly(sulfone) membranes crosslinked by trimesoyl chloride: Characterization and dehydration of ethylene glycol–water mixtures

Composite membranes prepared from poly(vinyl alcohol) and poly(sulfone) were crosslinked with trimesoyl chloride (TMC) solutions. The degree of crosslinking, crystallinity, surface roughness and hydrophobicity of the crosslinked PVA–PSf membranes were determined from attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), X-ray diffraction (XRD), atomic force microscopy (AFM) and contact angle measurements, respectively. Results showed a consistent trend of changes in the physicochemical properties: the degree of crosslinking, crystallinity, surface roughness, hydrophobicity and swelling degree all decrease with increasing crosslinking agent (TMC) concentration and reaction time. The crosslinked membrane performance was assessed with pervaporation dehydration of ethylene glycol solutions at a range of concentrations (30–90 wt% EG) in the feed mixtures. The total flux of permeation was found to decrease, while the selectivity to increase, with increasing TMC concentration and reaction time. The decrease in flux was most prominent at low EG concentrations in the feed mixtures. In addition, the temperature effect on the pervaporation dehydration was investigated in relation to solution–diffusion mechanisms.