Cetylpyridinium-iodomercurate PVC membrane ion selective electrode for the determination of cetylpyridinium cation in Ezafluor mouth wash and as a detector for some potentiometric titrations

A potentiometric method is described for the determination of cetylpyridinium (CP) cation using a polyvinyl chloride powder (PVC) membrane sensor based on CP-iodomercurate ion pair as an electroactive material. The sensor shows a linear response for CP ion over the concentration range of 2x10(-6)-1x10(-3) M at 25 degrees C. The electrode posses a sub-Nernstian slope of 29.0+/-0.4 mV decade(-1), which has been thoroughly discussed.The electrode shows a fast potential response of approximately 50 s, which is almost constant over a pH range of 3.0-6.0. Selectivity coefficient data for some common ions show negligible interference, however, cetyltrimethylammonium bromide (CTMAB) interferes significantly. An average recovery of 98.8% for CP with an average relative standard deviation (R.S.D.) of 1.2% has been achieved. The determination of CPC in Ezafluor mouth wash gave result that compare favorably with those obtained by the British Pharmacopoeia method. The CP electrode has been utilized as an end point indicator electrode in potentiometric titration of some anions, and applied for the determination of anionic surfactants in some commercial detergents and waste water.     

A novel ethacrynic acid sensor based on a lanthanide porphyrin complex in a PVC matrix

Lanthanide porphyrin complexes synthesized by a solid state method were used to prepare a novel ethacrynic acid (EA) sensor. The sensor, based on pentane-2,4-dionato(meso-tetraphenylporphinato)terbium [TbTPP(acac)] with an optimized membrane composition, exhibits a Nernstian response to EA- ion in the concentration range 7.4 x 10(-6)-1.0 x 10(-1) mol l-1 with a pH range from 3.2 to 6.8 and a fast response time of 30 s. The electrode shows improved selectivity towards EA- ion with respect to common co-existing ions compared with the previously reported EA sensor. As electroactive materials, lanthanide porphyrin complexes show better potentiometric response characteristics than copper porphyrin complexes. The effect of solvent mediators and lipophilic ion additives was studied and the experimental conditions were optimized. The electrode was applied to the determination of EA in human urine samples with satisfactory results.     

Potentiometric PVC membrane sensor for the determination of scopolamine in some pharmaceutical formulations.

A novel PVC membrane electrode for the determination of scopolamine ion based on the formation of an ion-association complex of scopolamine with the phosphotungstate counter anion as an electroactive material dispersed in a PVC matrix is described. The sensor shows a fast, stable, near-Nenstian response for 1 x 10(-2) mol dm(-3) to 1 x 10(-6) mol dm(-3) scopolamine at 25 degrees C over the pH range of 3 - 7 with a cationic slope of 54.5 +/- 0.5 mV/decade. The lower detection limit is 8 x 10(-7) mol dm(-3) and the response time is 15 -45 s. The selectivity coefficients for scopolamine relative to the number of interfering substances were investigated. There was negligible interference from the studied cations, anions, and pharmaceutical excipients. The determination of scopolamine in aqueous solution shows an average recovery of 100.0% and a mean relative standard deviation (RSD) of 1.5% at 500 microg/cm3. The direct determination of scopolamine in some formulations (scopolamine injection and eye drops) gave results that compare favorably with those obtained by the United State of Pharmacopoeia method. Potentiometric titration of scopolamine with sodium tetraphenylborate and phosphotungstic acid as a titrant was monitored with the developed scopolamine electrode as an end point indicator electrode.     

The enhanced electrogenerated chemiluminescence of Ru(bpy)3(2+) by glutathione on a glassy carbon electrode modified with some porphine compounds

It has been found that the electrochemical activity of glutathione was increased greatly at the glassy carbon electrodes modified with 5,10,15,20-tetraphenylporphine ruthenium(II) carbenyl (RuTPP), meso-tetraphenylporphine copper(II) complex (CuTTP) and hemin. It has been also found that glutathione would enhance the electrogenerated chemiluminescence (ECL) of Ru(bpy)3(2+) at a hemin glassy carbon electrode; the enhanced ECL intensity was linear with the concentration of glutathione in the range of 1 x 10(-7)-1 x 10(-4) mol l-1, based on which method for determination of glutathione has been developed. The detection limit of glutathione was 2 x 10(-8) mol l-1, and the relative standard deviation for 1 x 10(-6) mol l-1 glutathione was 2.7%. The mechanism for this ECL system has been proposed.     

Highly selective thiocyanate poly(vinyl chloride) membrane electrode based on a cadmium-Schiff's base complex

A PVC membrane electrode based on a cadmium-salen (N,N'-bis-salicylidene-1,2-ethylenediamine) complex as an anion carrier is described. The electrode has an anti-Hofmeister selectivity sequence with a preference for thiocyanate at pH 1.5-11.0. It has a linear response to thiocyanate from 1.0 x 10(-6) to 1.0 x 10(-1) mol L(-1) with a slope of 59.1 +/- 0.2 mV per decade, and a detection limit of 7 x 10(-7) mol L(-1). This electrode has high selectivity for thiocyanate relative to many common organic and inorganic anions. The proposed sensor has a fast response time of approximately 15 s. It was applied to the determination of thiocyanate in a milk sample.     

Bismetalloporphyrin-based ISE sensitive to fluoroborate

Several mu-oxo-bismetalloporphyrin complexes were synthesized for preparing fluoroborate sensors. The electrode based on mu-oxo-bis[tetra(p-chlorophenyl)porphinatomanganese(III)] with an optimized membrane composition shows a potentiometric response towards fluoroborate ion over the concentration range from 4.3 x 10(-7) to 1.0 x 10(-1) mol l-1 with a Nernstian slope, a wide working pH range from 5.5 to 12.0 and a fast response time of 30 s. The electrode shows anti-Hofmeister selectivity towards BF4- with respect to common co-existing ions, which is an improvement over methods reported so far. As electroactive materials, several mu-oxo-bismetalloporphyrins with different substituents on the benzene rings were compared for potentiometric response characteristics. The interaction between BF4- and bismetalloporphyrin was investigated using UV/VIS spectrophotometry. The electrode was applied to the determination of fluoroborate in electroplating solutions.     

PVC membrane ion selective electrode for the determination of pentachlorophenol in water, wood and soil using tetrazolium pentachlorophenolate

A novel PVC membrane electrode selective for the determination of pentachlorophenolate (PCP) ion based on 2,3,5-triphenyl-2H-tetrazolium (TPT) pentachlorophenolate ion pair as an electroactive material is described. The electrode shows a linear response for PCP ion over the concentration range of 6x10(-5) to 1x10(-2) M with lower detection limit of 4x10(-5) M at 25 degrees C. The electrode posses a Nernstian slope of -55.0+/-1.0 mV/decade and a fast potential response of 45 s, which is almost constant over a pH range of 5.5-10.5. Selectivity coefficient data for some common ions show negligible interference, however, 2,4,6-trichlorophenolate and cetylpyridinium ions interfere. An average recovery of 96.2% with relative standard deviation of 2.3% has been achieved for the determination of 75.0 ppm PCP in wastewater samples. The determination of PCP in soil and wood samples gave results that compare favorably with those obtained by gas chromatography. The electrode has been utilized as an end point indicator electrode for the determination of PCP using potentiometric titration.     

Spectrophotometric determination of vitamin E (alpha-tocopherol) using copper(II)-neocuproine reagent

A coated graphite-epoxy ion-selective electrode for bismuth(III), based on the ion-pair between the [Bi(EDTA)](-) anion and tricaprylylmethylammonium cation (Aliquat 336S) incorporated onto a poly(vinylchloride) (PVC) matrix is constructed. A thin membrane film of this ion-pair, dibutylphthalate (DBPh) or ortho-nitrophenyloctylether (o-NPOE) in PVC was deposited directly onto a Perspex(R) tube which contained a graphite-epoxy conductor substrate attached to the end of a glass tube. The coating solution was prepared by dissolving 30% (w/w) of PVC in 10 ml of tetrahydrofuran following addition of 65% (w/w) DBPh or o-NPOE and 5% (w/w) of the ionic pair. The effect of pH, EDTA concentration and some cation and anion on the electrode response is investigated. The bismuth(III) ion-selective electrode shows a linear response in the bismuth(III) concentration range from 1.0 x 10(-8) to 1.0 x 10(-1) mol 1(-1) and 1.0 x 10(-7) to 1.0 x 10(-1) mol 1(-1) and a slope of 56.8 and 59.2 mV dec.(-1) for the polymeric membranes containing DBPh and o-NPOE, respectively. The lifetime of this electrode was superior to 1 year (over 1600 determinations for each polymeric membrane), with practical detection limits of 6.3 x 10(-9) and 4.4 x 10(-8) mol 1(-1) with these plasticizers. Application of this electrode with bismuth(III) determination in a stomach anti-acid sample is described.     

Studies on the potentiometric thallium(III)-selective carbon paste electrode and its possible applications

Construction, performance characteristics and applications of a carbon paste thallium(III) ion-selective electrode are described. The electrode, which is based on ion-associate compounds formed between cetylpyridinium and chlorothallate(III) complexes dissolved in tricresyl phosphate as pasting liquid, showed near-Nernstian response over the concentration range of 5.8 x 10(-6) - 2.9 x 10(-3) mol/L. Potentiometric titrations of thallium(III) with cetylpyridinium chloride were affected by higher concentrations of excess halides, probably due to the formation of higher halogenothallates.     

An optical fiber sensor for berberine based on immobilized 1,4-bis(naphth[2,1-d]oxazole-2-yl)benzene in a new copolymer

A new copolymer made of 8-quinolyl methacrylate, methyl methacrylate and n-butyl acrylate(PQMB) has been used as a solid substrate for the preparation of an optical fiber berberine sensor. The sensing is based on the fluorescence of 1,4-bis(naphth[2,1-d]oxazole-2-yl)benzene(BNOB) immobilized in the copolymer quenched by berberine with the formation of 1:1 complex between them. The membrane composition was optimized using the orthogonal experimental design. Using the sensor described above, berberine in a sample solution from 4.02x10(-7) mol l(-1) to 2.82x10(-4) mol l(-1) can be detected. The sensor has satisfactory reversibility and a short response time of less than 30 s. The relative standard deviations for repeated measurements (n=15) of 8.05x10(-6) mol l(-1) and 4.02x10(-5) mol l(-1) beberine are 0.43% and 0.33%, respectively. The sensor shows good selectivity over alkali and alkali-earth metal salts and some common pharmaceutical species and can be used for the determination of berberine in pharmaceutical preparations.     

Rapid determination of lactulose in milk by microdialysis and biosensors

A simple and rapid flow system for the determination of lactulose in milk samples was developed. It is based on the hydrolysis of lactulose to galactose and fructose by the enzyme beta-galactosidase immobilised in a reactor. The amount of fructose produced was measured with an electrochemical biosensor based on the fructose dehydrogenase enzyme, K3[Fe(CN)6] as mediator and a platinum based electrochemical transducer. Parameters such as the enzyme immobilisation in the reactor and under the electrode surface, the lifetime of the beta-galactosidase reactor and of the dehydrogenase biosensor and the flow parameters were studied and optimised. Fructose was determined in the range 1 x 10(-6)-5 x 10(-3) mol l-1 with an RSD of about 2% and a detection limit of 5 x 10(-7) mol l-1. The use of a microdialysis probe as the sampling system permitted the direct measurement of lactulose in milk samples without pre-treatment in the range 1 x 10(-5)-5 x 10(-3) mol l-1. The sensitivity of the procedure allowed pasteurised, UHT and in-container sterilised milk to be distinguished.     

Spectrophotometric determination of samarium(III) with chrome azurol S in the presence of cetylpyridinium chloride

A sensitive, simple method for the determination of trace amounts of samarium by spectrophotometry is described based on the formation of the samarium-chrome azurol S (CAS) complex in micellar medium. The molar absorptivities of the complexes at pH 7.5 at 505 nm were 3.6x10(4) and 1.4x10(5) l mol(-1) cm(-1) for water media and cetylpyridinium chloride (CPC), respectively. Beer's law is obeyed from 0.05-2 mg l(-1) of samarium at 505 nm as Sm-CAS-CPC complex. Optimal conditions such as reagent amounts, and pH for the samarium determination were reported. The effects of foreign ions were also investigated. The proposed method was successfully applied to the determination of samarium contents in synthetic samples.     

Fiber-optic sensor for iodine based on a covalently immobilized aminobenzanthrone Schiff base.

An aminobenzanthrone Schiff base has been synthesized as a new fluorescence carrier for the preparation of an optical chemical sensor for iodine. The response of the sensor is based on fluorescence quenching of the aminobenzanthrone Schiff base by iodine. The sensor shows a linear response toward iodine in the range of 1.0 x 10(-5) to 1.0 x 10(-3) mol l(-1), with a detection limit of 6.0 x 10(-6) mol l(-1) at pH 8.0. Leaching of the fluorophore from the membrane is effectively hindered by covalent immobilization, resulting in an enhanced sensor lifetime. In addition to satisfactory reproducibility and reversibility, the prepared sensor exhibits sufficient selectivity toward iodine with respect to other coexisting ions. The sensor has been applied to the determination of iodine in common salt samples.     

Ion-selective electrode for aluminum determination in pharmaceutical substances, tea leaves and water samples

A novel ion-selective PVC membrane sensor for Al(III) ions based on 6-(4-nitrophenyl)-2-phenyl-4-(thiophen-2-yl)-3,5-diaza-bicyclo[3.1.0]hex-2-ene (NTDH) as a new ionophore has been prepared and studied. The electrode exhibit a good response for aluminum ion over concentration range of 1.0x10(-6) to 1.0x10(-1) mol L(-1) with a Nernstian slope of 19.6+/-0.4 mV per decade and low detection limit of 6.3x10(-7) mol L(-1). The best performance was obtained with membrane composition 30% poly(vinyl chloride), 62% acetophenone, 5% oleic acid, 3% ionophore and 2 ml tetrahydrofuran. NTDH-based electrode was suitable for aqueous solutions of pH 3. It has relatively fast response time (approximately 10 s) and can be used at least for 3 months without any considerable divergence in potentials. The proposed membrane electrode revealed good selectivity for Al(III) ions over a wide variety of other cations. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficient of the electrode. The formation constant and stoichiometry ratio of ionophore-Al(III) complex were calculated at 25 degrees C by using segmented sandwich membrane method. It was used in non-aqueous solvents and also as indicator electrode in potentiometric determination of Al(III) ions in some real samples.     

Cesium-selective membrane electrode based on a recently synthesized 16-membered macrocyclic diamide

A PVC membrane sensor for the Cs+ ion based on 1,5-diaza-2,3,4-naphthyl-8,11,14-trioxacyclohexadecane-6,16-dione (L) has been prepared. The sensor has a linear dynamic range of 5.0 x 10(-1) - 6.9 x 10(-6) mol L(-1), a Nernstian slope of 59.5 +/- 0.8 mV decade(-1), and a detection limit of 4.7 x 10(-6) mol L(-1). It has a fast response time of <15 s and can be used for at least 8 weeks without any considerable divergence in potentials. The selectivity of the proposed electrode relative to alkali, alkaline earth, and transition metal ions was comparatively good. The electrode could be used in the pH range 4.5-11.0.     

The use of phenylfluorone in the presence of cetylpyridinium chloride and Triton X-100 for the spectrophotometric determination of copper(II) in blood serum

A simple and sensitive spectrophotometric method for determination of copper(II) is based on the formation of a blue coloured complex of Cu(II) with 9-phenyl-2,3,7-trihydroxy-6-fluorone (PF) in the presence of cetylpyridinium chloride (CP) and Triton X-100, has been developed. Optimum concentrations of PF, CP, Triton X-100 and pH ensuring maximum absorbance were defined. The complex Cu(II)-PF-CP-Triton X-100 shows maximum absorbance at 595 nm with a molar absorptivity value of 9.67x10(4) l mol(-1) cm(-1). The detection limit of the method is 0.028 mug ml(-1). Beer's law is obeyed for copper concentrations in the range 0.04-0.4 mug ml(-1). The studies of the effect of foreign ions on determination of copper, show that the selectivity of the method is poor. The cations of alkali metals and anions Br(-), Cl(-), I(-), F(-), NO(2)(-), NO(3)(-), CH(3)COO(-), SO(4)(2-), S(2)O(3)(2-), PO(4)(3-), citrates (examined in 1000-fold molar excess over copper) do not affect the determination. All cations forming complexes with PF have an interfering effect. The statistical evaluation of the method was carried out for six determinations using 10 mug of Cu and the following results were obtained: the standard deviation, SD=0.042, the confidence interval mu(95)=10.1+/-0.1 mug Cu. The method has been applied for determination of copper in blood serum.     

Coated-wire copper(II)-selective electrode based on phenylglyoxal-α-monoxime ionophore

A copper(II) ion-selective electrode based on a recently synthesized 2-quinolyl-2-phenylglyoxal-2-oxime (phenylglyoxal-alpha-monoxime) has been developed. The PVC-based membrane containing phenylglyoxal-alpha-monoxime, dibutyl phthalate as plasticizer, and sodium tetraphenylborate as anion excluder and membrane modifier, was directly coated on the surface of a platinum-wire electrode. The response of the electrode was linear with a near-Nernstian slope of 28.2 mV decade(-1) within the Cu2+ ion concentration range 1x10(-6)-1x10(-1) mol x L(-1). The response time for the proposed electrode to achieve a 95% steady potential for Cu2+ concentrations ranging from 1x10(-1) to 1x10(-6) mol x L(-1) is between 10 and 50 s, and the electrode is suitable for use within the pH range of 3 to 6.5. The electrode has a detection limit of 5x10(-7) mol x L(-1) Cu2+ and its selectivity relative to several alkali, alkaline earth, transition, and heavy metal ions was good. The coated-wire electrode could be used for at least two months without a considerable alteration of its potential. Applications of the electrode for determination of copper in milk powder samples and as an indicator electrode for potentiometric titration of Cu2+ ion using EDTA are reported.     

Differential-pulse voltammetric determination of trace formaldehyde using magnetic microspheres and magnetic electrode

A new type of magnetic polymer microsphere containing acylhydrazine groups on the surface was synthesized. They can be reacted with formaldehyde to produce an electroactive adduct. Reduction of these derivatives following aggregation on a magnetic electrode is possible and is effective in the indirect determination of formaldehyde. The experimental conditions and electrode structure are discussed. Under the optimum conditions, it was found that the peak potential (Ep) of formaldehyde is -1.01 V (vs. Ag/AgCl). Formaldehyde in the range 1-1000 micrograms l-1 can be determined. The detection limit for formaldehyde is 0.3 microgram l-1 and the relative standard deviation for the determination of 100 micrograms l-1 formaldehyde was 2.26%. The method was applied to the determination of formaldehyde in environmental samples with satisfactory results.     

Papaverine PVC membrane ion-selective electrodes based on its ion-exchangers with tetraphenylborate and tetrathiocyanate anions

The construction and general performance of novel potentiometric membrane ion selective electrodes for determination of papaverine hydrochloride has been described. They are based on the formation of the ion association complexes of papaverine (PA) with tetraphenylborate (TPB)(I) or tetrathiocyanate (TTC)(II) counter anions as electro-active material dispersed in a PVC matrix. The electrodes show fast, stable, near Nernstian response for 1 x 10(-2) to 6 x 10(-5) M and 1 x 10(-2) to 1 x 10(-5) M for PA-TPB and PA-TTC respectively at 25 degrees C over the pH range of 3-5.0 with a cationic slope of approximately 56.5 +/- 0.5 mV/decade for both sensors respectively. The lower detection limit is 4 x 10(-5) and 8 x 10(-6) M for PA- I and PA-II respectively with fast response time ranging from 20-45 sec. Selectivity coefficients for PA relative to a number of interfering substances were investigated. There is a negligible interference from the studied cations, anions, and pharmaceutical excipients. The determination of 4.0- 3000.0 microg/ml of PA in aqueous solutions shows an average recovery of 99.1% and a mean relative standard deviation of 1.4 at 100microg/ml. The direct determination of PA in some formulations (Vasorin injection) gave results that compare favorably with those obtained using the British Pharmacopoeia method. Potentiometric titration of PA with sodium tetraphenylborate and potassium thiocyanate as titrants utilizing the papaverine electrode as an end point indicator electrode has been carried out.     

Voltammetric determination of mifepristone at a DNA-modified carbon paste electrode

A new strategy for the preparation of a DNA-modified carbon paste electrode is developed. It is found that the anodic response of mifepristone is greatly enhanced at the dsDNA-modified carbon paste electrode comparing with that obtained at the bare electrode, while the response at a ssDNA-modified electrode is similar to bare electrode. So the dsDNA-modified electrode is employed as a sensitive biosensor for the detection of mifepristone. A linear dependence of the peak currents on the concentration is observed in the range 2.0 x 10(-7) approximately 2.0 x 10(6) mol/L, with a detection limit of 1.0 x 10(-7) mol/L. The relative standard deviation is 4.3% for six successive determinations of 1.0 x 10(6) mol/L mifepristone. The determination of mifepristone tablets is carried out and satisfactory results are obtained.