Thermal decomposition properties and compatibility of CL-20, NTO with silicone rubber

The new polycyclic nitramine 2,4,6,8,10,12-hexanitrohexaazaisowurtzitane (HNIW) has been focused as a considerable amount of research recently on investigating its polymorphs, relative stability, and respective reaction chemistry. It is known as CL-20 popularly, CL-20 is a very high-energy and relatively high oxygen balance value crystalline compound whose method of synthesis and detailed performance data are still classified. 5-oxo-3-nitro-1,2,4-triazole (NTO, or nitrotriazolone) was an insensitive molecule comparison general explosives, and the NTO based polymer bonded explosives (PBX) was a low vulnerability explosive. Both energetic materials are all very important high explosives, which is used in a variety of military formulations widely owing to the properties of high energy and desensitization of PBX, many researchers have demonstrated the usefulness of above two energetic materials in explosive component. In this work, the thermal decomposition characteristics of explosives CL-20 and NTO were studied using thermal analytical techniques (TG, DSC), then the compatibility of above two explosives with silicone rubber, and the decomposition kinetic parameters such as activation energies of decomposition, the frequency factor of the decompose reaction are also evaluated by non-isothermal DSC techniques.     

Thermal Analysis of Binary Systems. Explosive – lead compound

The thermal decomposition of explosives: pentaerythrol tetranitrate (PETN), 2,4,6-trinitrotoluene(TNT), cyclo-1,3,5-trimethylene-2,4,6-trinitroamine (RDX) and their two-component mixtures with 40% of lead compounds [PbO, Pb₃O₄, Pb(NO₃)₂] were performed. The simple method of determination of stability changes in the mixtures described above, in comparison with pure explosives was presented. The lead oxides accelerated significantly the thermal decomposition of explosives. Pb(NO₃)₂ acts as a catalyst in the mixture containing TNT degradation, but not in a case of PETN and RDX. This revised version was published online in August 2006 with corrections to the Cover Date.     

HMX和HMX/HTPB PBX的晶体缺陷理论研究

建立空位和掺杂点缺陷模型, 用分子动力学(MD)方法, 研究晶体缺陷对β-环四亚甲基硝胺(HMX)和β-HMX/HTPB(端羟基聚丁二烯)高聚物粘结炸药(PBX)的力学性能和爆炸性能的影响. 结果表明, 相对于HMX“完美”晶体(1)考察缺陷晶体(2和3), 以及相对于HMX完美晶体基PBX(1)考察缺陷PBX 2和PBX 3, 均发现弹性系数和(拉伸、体积、剪切)模量下降, 导致体系刚性减弱, 延展性和韧性增强. 这与在基炸药HMX晶体(1, 2和3)中分别加入HTPB高聚物粘结剂形成PBX 1, PBX 2和PBX 3呈现类似的相应的变化趋势和效果. 此外, 研究表明, 爆炸性质也依赖于体系的组成和结构. 因加入的是低能高聚物, 故PBX(1), PBX(2)和PBX(3)的爆热、爆速和爆压均比相应的基炸药(1, 2和3)低, 即晶体(1)＞PBX(1), 晶体(2)＞PBX(2), 晶体(3)＞PBX(3). PBX(1), PBX(2), PBX(3)与对应基炸药(1, 2, 3)的爆速和爆压取相同变化次序, 亦即PBX(1)＞PBX(2)＞PBX(3)对应于晶体(1)＞晶体(2)＞晶体(3). 这些计算结果和规律对PBX配方设计显然具有指导作用.     

端羟基聚丁二烯/增塑剂共混物相容性的分子动力学模拟

固体推进剂和炸药的力学性能在很大程度上依赖于配方中高分子粘结剂与增塑剂的相容性. 本文对相容和非相容两种体系进行了分子动力学(MD)模拟, 以考察分子模拟方法的实用性. 为预测固体推进剂中端羟基聚丁二烯(HTPB)与增塑剂癸二酸二辛酯(DOS)、硝化甘油(NG)的相容性, 采用MD模拟方法在COMPASS力场下, 对HTPB、DOS、NG和共混物HTPB/DOS、HTPB/NG的密度、内聚能密度及溶度参数等进行了模拟计算. 通过比较溶度参数差值(△δ)的大小、分子间径向分布函数和模拟前后体系密度变化情况均可以预测HTPB/DOS属于相容体系,而HTPB/NG属于不相容体系, 与实验结果一致. 径向分布函数分析同时揭示了HTPB/增塑剂组分之间的相互作用及本质. 本文的模拟方法可以作为预测聚合物与增塑剂相容性的有利工具, 也可以为固体推进剂和炸药的配方设计提供理论指导.     

Note on the use of the vacuum stability test in the study of initiation reactivity of attractive cyclic nitramines in Formex P1 matrix

The zero-order reaction rates (specific rate constants) of isothermal decomposition at 120 °C of plastic bonded explosives (PBXs) were measured by means of the Czech vacuum stability test, STABIL. The PBXs are based on 1,3,5-trinitro-1,3,5-triazinane (RDX), 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX), cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole (BCHMX), and ε 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (ε-HNIW, ε-CL-20) with 13 wt% of the Formex P1 type matrix, i.e., a matrix of the explosive with pentaerythritol tetranitrate (PETN) bound by 13 wt% of a mixture of 25 wt% of styrene–butadiene rubber and 75 wt% of an oily material. Dependencies were found between the specific rate constants mentioned and the detonation velocities of PBXs, and consequently between these constants and the impact and electric spark sensitivities of pure explosive fillers, i.e., RDX, HMX, HNIW, BCHMX, and PETN. It is stated that the higher impact or electric spark sensitivity of their pure explosive fillers corresponds to the higher thermal reactivity of the given PBXs.     

Optimized thermal desorption for improved sensitivity in trace explosives detection by ion mobility spectrometry

In this work we evaluate the influence of thermal desorber temperature on the analytical response of a swipe-based thermal desorption ion mobility spectrometer (IMS) for detection of trace explosives. IMS response for several common high explosives ranging from 0.1 ng to 100 ng was measured over a thermal desorber temperature range from 60 °C to 280 °C. Most of the explosives examined demonstrated a well-defined maximum IMS signal response at a temperature slightly below the melting point. Optimal temperatures, giving the highest IMS peak intensity, were 80 °C for trinitrotoluene (TNT), 100 °C for pentaerythritol tetranitrate (PETN), 160 °C for cyclotrimethylenetrinitramine (RDX) and 200 °C for cyclotetramethylenetetranitramine (HMX). By modifying the desorber temperature, we were able to increase cumulative IMS signal by a factor of 5 for TNT and HMX, and by a factor of 10 for RDX and PETN. Similar signal enhancements were observed for the same compounds formulated as plastic-bonded explosives (Composition 4 (C-4), Detasheet, and Semtex). In addition, mixtures of the explosives exhibited similar enhancements in analyte peak intensities. The increases in sensitivity were obtained at the expense of increased analysis times of up to 20 seconds. A slow sample heating rate as well as slower vapor-phase analyte introduction rate caused by low-temperature desorption enhanced the analytical sensitivity of individual explosives, plastic-bonded explosives, and explosives mixtures by IMS. Several possible mechanisms that can affect IMS signal response were investigated such as thermal degradation of the analytes, ionization efficiency, competitive ionization from background, and aerosol emission.     

Molecular dynamics simulations for pure epsilon-CL-20 and epsilon-CL-20-based PBXs

Molecular dynamics has been employed to simulate the well-known high energy density compound epsilon-CL-20 (hexanitrohexaazaisowurtzitane) crystal and 12 epsilon-CL-20-based PBXs (polymer bonded explosives) with four kinds of typical fluorine polymers, i.e., polyvinylidenedifluoride, polychlorotrifluoroethylene, fluorine rubber (F(2311)), and fluorine resin (F(2314)) individually. The elastic coefficients, isotropic mechanical properties (tensile moduli, bulk moduli, shear moduli, and poission's ratios), and bonding energy are first reported for epsilon-CL-20 crystal and epsilon-CL-20-based polymer bonded explosives (PBXs). The mechanical properties of epsilon-CL-20 can be effectively improved by blending with a small amount of fluorine polymers, and the whole effect of the adding fluorine polymers to improve mechanical properties of PBXs along the three crystalline surfaces of epsilon-CL-20 is found to be (100) approximately (001) > (010). The interaction between each of the crystalline surfaces and each of the fluorine polymers is different, and the ordering of binding energy for the three surfaces is (001) > (100) > (010); F(2314) always has the strongest binding ability with the three different surfaces. F(2314) can best improve the ductibility and tenacity of PBX when it is positioned on epsilon-CL-20 (001) crystal surface. The calculations on detonation performances for pure epsilon-CL-20 crystal and the four epsilon-CL-20-based PBXs show that adding a small amount of fluorine polymer into pure epsilon-CL-20 will lower detonation performance, but each detonation parameter of the obtained PBXs is still excellent.     

分子动力学模拟浓度和温度对TATB/PCTFE PBX力学性能的影响

为探讨高聚物粘结炸药(Polymer Bonded Explosive, PBX)的力学性能随温度和高聚物浓度而变化的规律, 用分子动力学(MD)方法和compass力场, 对著名高能炸药1,3,5-三氨基-2,4,6-三硝基苯(TATB)与常用高聚物粘结剂聚三氟氯乙烯(PCTFE)所构成的TATB/PCTFE PBX进行模拟计算. 结果表明, 在一定范围内, 随高聚物浓度的增加, PBX的弹性系数和模量减小, 表明其刚性减小、弹性增加; 而随温度的升高, PBX的刚性减小、弹性增强. 还发现PBX的结合能随浓度增高而增大, 随温度升高而减小.     

Low-mass ions observed in plasma desorption mass spectrometry of high explosives

The low-mass ions observed in both positive and negative plasma desorption mass spectrometry (PDMS) of the high explosives HMX, RDX, CL-20, NC, PETN and TNT are reported. Possible identities of the most abundant ions are suggested and their presence or absence in the different spectra is related to the properties of the explosives as matrices in PDMS. The detection of abundant NO+ and NO2- ions for HMX, RDX and CL-20, which are efficient matrices, indicates that explosive decomposition takes place in PDMS of these three substances and that a contribution from the corresponding chemical energy release is possible. The observation of abundant C2H4N+ and CH2N+ ions, which have high protonation properties, might also explain the higher protein charge states observed with these matrices. Also, the observation of NO2-, possibly formed by electron scavenging which increases the survival probability of positively charged protein molecular ions, completes the pattern. TNT does not give any of these ions and it is thereby possible to explain why it does not work as a PDMS matrix. For NC and PETN, decomposition does not seem to be as pronounced as for HMX, RDX and CL-20, and also no particularly abundant ions with high protonation properties are observed. The fact that NC works well as a matrix might be related to other properties of this compound, such as its high adsorption ability.     

Study of initiation reactivity of some plastic explosives by vacuum stability test and non-isothermal differential thermal analysis

On the basis of measurements of 18 high explosives by means of the Czech Vacuum Stability Test (VST) STABIL, a relationship has been specified between the results of this test and those of Russian manometric method. The said relationship was used to predict the Arrhenius parameters (E_a and log A values) of four plastic explosives based on RDX and one high explosive based on PETN (Semtex). The slopes E_aR⁻¹ of Kissinger's equation were specified by means of non-isothermal differential thermal analysis (DTA) and evaluation of the measurement results by means of the Kissinger method. The role played by binders and plasticizers in thermal decomposition of nitramines was pointed out on the basis of relationship between the E_a values obtained from VST and the E_aR⁻¹ values obtained from DTA, both for plastic explosives, eight nitramines, Composition B and PETN. The relationships between the E_aR⁻¹ values and thermostability threshold was specified for the given group of explosives. The relationship classify some of the studied plastic explosives as belonging to nitramines with steric hindrance in the molecule (CPX, TNAZ and HNIW). The relationship between E_aR⁻¹ values and drop energies, E_dr, sharply differentiates between plastic explosives and individual nitramines. From the relationship between the E_dr and D² values it was found that the increasing performance of the studied nitramines and plastic explosives is connected with the decrease in their impact sensitivity. Also specified are the approximate linear dependences between the peak temperatures of exothermic decomposition of all the explosives studied and their ignition temperatures, T_ig, or critical temperatures, T_c; these dependences were applied to prediction of T_ig and T_c of both the studied plastic explosives and some of the nitramines.     

Studies on the properties of EPDM–CSE blend containing HTPB for case‐bonded solid rocket motor insulation

Elastomeric blends based on ethylene propylene diene (EPDM) rubber as a primary polymer have been investigated for the thermal insulation of case‐bonded solid rocket motors (SRMs) cast with composite propellant containing hydroxy terminated polybutadiene (HTPB) as a polymeric binder. EPDM rubber found as an attractive candidate for the thermal insulation of case‐bonded SRM due to the advantages such as low specific gravity, improved ageing properties, and longer shelf life. In spite of these advantages, EPDM, a non‐polar rubber, lacks sufficient bonding with the propellant matrix. Bonding properties are found to improve when EPDM is blended with other polar rubbers like polychloroprene, chlorosulphonated polyethylene (CSE), etc. This type of polar polymer when blended with EPDM rubber enhances the insulator‐to‐propellant interface bonding. In the present work, an attempt has been made to study the properties of EPDM–CSE based insulator by incorporating HTPB, a polar polymer as well as a polymeric binder, as an additive to the EPDM–CSE blend by varying the HTPB concentration. Blends prepared were cured and characterized for rheological, mechanical, interface, and thermal properties to study the effect of HTPB addition. This paper reports the preliminary investigation of the properties of EPDM–CSE blend containing HTPB, as a novel and futuristic elastomeric insulation for case‐bonded SRM containing HTPB as propellant binder. Copyright © 2007 John Wiley & Sons, Ltd.     

RDX基PBX的模型、结构、能量及其与感度关系的分子动力学研究

以RDX（环三亚甲基三硝胺）为基、PS（聚苯乙烯）为粘结剂构成PBX（高聚物粘结炸药）的MD（分子动力学）模拟初始模型.比较分别以1根46链节和2根23链节PS置于RDX（001）晶面上的两种（PBX1和PBX2）模型下的MD模拟结果,发现二者的结构、相互作用能和力学性能均很接近.取PBX2进行5种温度（195,245,295,345和395 K）下的NPT系综、MD模拟系统研究,发现随温度依次升高,各体系中RDX引发键N NO2键的最大键长（Lmax）递增,N–N键连的N与N之间的双原子作用能（EN-N）和内聚能密度（CED）递减,与感度随温度升高而增大的实验事实相一致.综合已有工作,对高能复合材料（如PBX和固体推进剂等）的感度理论研究,建议关注其中易爆燃组分在外界刺激下的结构和能量变化,其引发键Lmax和作为引发键强度度量的双原子作用能（如EN-N）,可作为热和撞击感度相对大小的理论判据.     

Micro structural investigations on TNT and PETN incorporated silica xerogels

Silica xerogels incorporated with trinitrotoluene (TNT) and pentaerythritoltetranitrate (PETN) were synthesized using sol–gel method. Tetramethoxysilane was used as precursor for silica. TNT and PETN content in the resulted explosive/silica xerogel was varied ranging from 50 to 90%. Infra red spectra showed that explosives were retained in the silica xerogel matrix. Transmission electron microscopy (TEM) reveal that explosives particles were uniformly distributed in xerogel matrix and the size of the PETN and TNT particles are in the range 15–18 nm. Small angle x-ray scattering showed that the sizes of the pores in the silica matrix are in the range 25–13 nm. The particles of TNT and PETN occupy the pores in the matrix resulting in gradual reduction of pore-size affecting the surface characteristics of the pore-matrix interface. Understanding of the structure of aggregates of small particles thus produced could be useful to explain the properties shown by the fine explosives. Our study suggests that particle size of explosives in the nanometer range can be achieved using the sol–gel method.     

Thermodynamic analysis of pure and impurity doped pentaerythritol tetranitrate crystals grown at room temperature

Pentaerythritol tetranitrate (PETN) powders are used to initiate other explosives. During long-term storage, changes in powder properties can cause changes in the initiation performance. Changes in the morphology and surface area of aging powders are observed due to sublimation and growth of PETN crystals through coarsening mechanisms, (e.g. Ostwald ripening, sintering, etc.). In order to alleviate the sublimation of PETN crystals under service conditions, stabilization methods such as thermal cycling and doping with certain impurities during or after the crystallization of PETN have been proposed. In this report we present our work on the effect of impurities on the morphology and activation energy of the PETN crystals. The pure and impurity doped crystals of PETN were grown from supersaturated acetone solution by solvent evaporation technique at room temperature. The difference in the morphology of the impurity-doped PETN crystal compared to pure crystal was examined by optical microscopy. The changes in the activation energies and the evaporation rates are determined by thermogravimetry (TG). Our activation energies of evaporation agree with earlier reported enthalpies of vaporization. The morphology and activation energy of PETN crystals doped with Ca, Na, and Fe cations are similar to that for pure PETN crystal, whereas the Zn-ion-doped PETN crystals have different morphology and decreased activation energy.     

Molecular dynamics study on the relationships of modeling, structural and energy properties with sensitivity for RDX-based PBXs

In this paper,a primary model is established for MD(molecular dynamics) simulation for the PBXs(polymer-bonded explosives) with RDX(cyclotrimethylene trinitramine) as base explosive and PS as polymer binder.A series of results from the MD simulation are compared between two PBX models,which are represented by PBX1 and PBX2,respectively,including one PS molecular chain having 46 repeating units and two PS molecular chains with each having 23 repeating units.It has been found that their structural,interaction energy and mechanical properties are basically consistent between the two models.A systematic MD study for the PBX2 is performed under NPT conditions at five different temperatures,i.e.,195 K,245 K,295 K,345 K,and 395 K.We have found that with the temperature increase,the maximum bond length(L max) of RDX N N trigger bond increases,and the interaction energy(E N-N) between two N atoms of the N-N trigger bond and the cohesive energy density(CED) decrease.These phenomena agree with the experimental fact that the PBX becomes more sensitive as the temperature increases.Therefore,we propose to use the maximum bond length L max of the trigger bond of the easily decomposed and exploded component and the interaction energy E N-N of the two relevant atoms as theoretical criteria to judge or predict the relative degree of heat and impact sensitivity for the energetic composites such as PBXs and solid propellants.     

Radiation-induced decomposition of PETN and TATB under extreme conditions

We conducted a series of experiments investigating decomposition of secondary explosives PETN and TATB at varying static pressures and temperatures using synchrotron radiation. As seen in our earlier work, the decomposition rate of TATB at ambient temperature slows systematically with increasing pressure up to at least 26 GPa but varies little with pressure in PETN at ambient temperature up to 15.7 GPa, yielding important information pertaining to the activation complex volume in both cases. We also investigated the radiation-induced decomposition rate as a function of temperature at ambient pressure and 26 GPa for TATB up to 403 K, observing that the decomposition rate increases with increasing temperature as expected. The activation energy for the TATB reaction at ambient temperature was experimentally determined to be 16 +/- 3 kJ/mol.     

A novel form-stable paraffin-based hydroxyl-terminated polybutadiene binder containing microencapsulated paraffin wax

Leakage and incompatibility of paraffin wax (PW) in hydroxyl-terminated polybutadiene (HTPB) binders is a major obstacle to its application in polymer-bonded explosives (PBX). In order to solve this issue, we designed a microencapsulated PW (MePW)/PW/HTPB composite in this paper. Melamine–formaldehyde-shelled MePW (MF MePW)/PW/HTPB composites with different contents of MePW and PW were prepared by cast molding method. The chemical composition, crystallinity and microstructure of MePW/PW/HTPB composites were analyzed with Fourier transformed infrared spectroscopy, X-ray diffraction and scanning electron microscope, respectively. The results showed that PW and MF MePW have been uniformly dispersed in HTPB without any chemical interaction. Moreover, differential scanning calorimeter analysis, thermal gravimetric analyzer, thermal cycling test, leaking test, tensile and compressive test were used to investigate the thermal and mechanical properties of these composites. The composites have high latent heat and good thermal reliability. The thermal stability, tensile and compressive strength of MePW/PW/HTPB composites were dramatically increased with the increasing mass fraction of MePW. The introduction of MePW can obviously prevent the leakage of PW in both HTPB binders and PBX. Consequently, it is anticipated that MePW can be used in the next-generation of paraffin-based high-temperature PBX systems.

     

Theoretical predictions on pentaerythritol tetranitrate-based high energy density compounds

A novel family of pentaerythritol tetranitrate (PETN) derivatives based parent PETN skeleton were designed by introducing two energetic groups –NF₂ and –NO₂. Their electronic structure, heats of formation, detonation properties, impact sensitivity, and thermal stability were investigated by using density functional theory. The findings reveal that most of the title compounds have good detonation performance. The –NF₂ group played an important role in improving the densities, heats of detonation, and detonation properties of the designed molecules. The values of h₅₀ for almost all the PETN derivatives are higher than that of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine. An analysis of bond dissociation energy suggests that the N-NO₂ bond tends to be a trigger bond in thermal decomposition. Taking both detonation properties and thermal stabilities into consideration, the three compounds may be selected as potential high-energy-density compounds.     

Detonation Properties of High Explosives Containing Ammonia Borane

Ammonia borane (AB) is used as a combustion agent to improve the properties of high explosives. The detonation velocity (D_v) and detonation pressure (P) of raw high explosives and of samples containing AB were calculated and compared. The detonation properties, impact sensitivities, thermal sensitivities, and thermal decomposition characteristics of high explosives containing AB were also measured. The results indicated that when the AB content was 20 wt‐%, the optimal detonation velocity and detonation pressure were achieved. Both the detonation velocity and detonation pressure of the high explosives containing AB were clearly increased compared with those of the raw high explosives. Moreover, the detonation velocities of high explosives containing AB were 7078 to 7423 m · s^–1 and their density ranged from 1.570 to 1.589 g · cm^–3. The detonation pressure ranged from 34.5 to 37 GPa and the average heat of detonation was 6688 J · g^–1. Furthermore, the impact and thermal sensitivities were 170 cm and 613 K, respectively, whereas a slight change occurred in the thermal decomposition characteristics. These results suggest that AB can serve as a powerful combustible agent in energetic materials and improve the detonation properties and sensitivities of high explosives.     

Synthesis and optoelectronic properties of alternating benzofuran/terfluorene copolymer with stable blue emission

The solution processable alternating benzofuran/terfluorene copolymer bearing side oxadiazole groups ( PBF‐OXD ) was synthesized and its optoelectronic properties and color stability were investigated. Electron‐deficient and stereohindered oxadiazole units were used as pendent groups to compensate for the poor electron‐transporting ability of a p‐type polymer backbone, to depress the intermolecular π‐stacking, and to improve solubility while retaining polymer blue emission. PBF‐OXD showed a glass transition at 135 °C and an onset decomposition temperature of ～345 °C. A simple EL device, with the configuration of ITO/PEDOT:PSS/ PBF‐OXD /Ba/Al, displayed a stable blue emission (λ_max = 434 nm), good color purity (full width half‐maximum = 59 nm), maximum brightness of 1400 cd/m², and a maximum luminance efficiency of 0.95 cd/A. The PL and EL spectra changed slightly on annealing and on increasing the applied voltage. These results show that the as‐synthesized copolymer PBF‐OXD had integrated respective functions of its different building blocks and exhibited good thermal and color stability with improved EL performance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5488–5497, 2009