Extraction and separation of bismuth(III)

Separation of bismuth from beryllium, lead, iron(III), indium, scandium, lanthanum, antimony(III), zirconium, titanium, thorium, vanadium(V), molybdenum(VI), uranium (VI) and chromium(VI) is achieved by selective extraction of bismuth from 0.1M sodium salicylate solution (adjusted to pH 7) into mesityl oxide (MeO). The extracted species is Bi (HOC(6)H(4)COO)(3).3MeO. The results are accurate within +/- 0.5%, with a standard deviation of 0.8%. The separation and determination of bismuth takes only 15 min.     

Selective separation of bismuth (212Bi) from A228Th source

Using alkyl radicals, the nuclides²¹⁶Po,²¹²Pb,²¹²Bi and²⁰⁸Tl can be transported from a²²⁸Th source to a detection position. The separation of the alkyl compounds was investigated either using thermal decomposition or a reaction with a gas which yields a non volatile compound. Whereas the thermal decomposition leads only to low enrichment factors,²¹²Bi was separated selectively by introducing chlorine into the gas phase system.     

Oxidation of chromium(III) by alkaline hexacyanoferrate(III)

Alkaline hexacyanoferrate(III) oxidation of freshly prepared solutions of Cr^III (pH>12) at 27°C follows the rate law, Equation 1:

Determination of antimony(III) with potassium hexacyanoferrate(III)

The determination of antimony(III) with potassium hexacyanoferrate(III) in 5M hydrochloric acid medium and in the presence of 40% v/v acetic acid is described. Ferroin is used as the indicator. Antimony has been determined in tartar emetic, solder and pig lead. Arsenic(III) does not interfere.     

Anion exchange separation of bismuth and lead

Zusammenfassung Wismut und Blei können mit Hilfe des Anionenaustauschers Dowex 1 von mehreren anderen Elementen abgetrennt werden. Zur Elution der Elemente nacheinander werden methanolische oder wäßrige Lösungen von Salpeter- und Salzsäure verwendet. Das beschriebene Verfahren wurde zur Blei- und Wismutbestimmung in Stahl und Meeressedimenten benutzt.     

Extraction and separation of bismuth(III) from steel and bismuth-base alloys

Summary Separation of bismuth(III) from iron(III), molybdenum(VI), vanadium(V), chromium(VI), titanium(IV), antimony(III), lead(II), beryllium(II), uranium(VI), hafnium(IV), indium(III) and zirconium (IV) is achieved by solvent extraction with high molecular weight amines from sodium succinate solution adjusted to suitable pH. Bismuth(III) is stripped from the organic phase and determined spectrophotometrically. The method is shown to be applicable to bismuth alloys.

---

Extraktion und Trennung von Wismut(III) aus Stahl und wismuthältigen Legierungen

Zusammenfassung Wismut(III) läßt sich von Fe(III), Mo(VI), V(V), Cr(VI), Ti(IV), Sb(III), Pb(II), Be(II), U(VI), Hf(IV), In(III) und Zr(IV) durch Extraktion mit hochmolekularen Aminen aus Natriumsuccinat bei geeignetem pH trennen. Bi(III) wird dann von der organischen Phase getrennt und spektralphotometrisch bestimmt. Das Verfahren eignet sich für Wismutlegierungen.

     

Anion exchange studies of zirconium(iv) in citrate solution separation from mixtures

The anion exchange behaviour of zirconium(IV) in a citrate system is described. Nitric acid, hydrochloric acid, perchloric acid and ammonium chloride were tested as eluants on Dowex ₂₁K column. Zirconium is separated from fission product elements e.g., barium, strontium, cadmium, caesium, molybdate and also from lead.     

Flow-injection extraction spectrophotometric determination of bismuth as tetraiodobismuthate(III) with the tetramethylenebis(triphenylphosphonium) cation

Bismuth can be determined spectrophotometrically at 495 nm after its extraction as tetramethylenebis(triphenylphosphonium) tetraiodobismuthate(III) into dichloromethane. The carrier stream is 2 M sulphuric acid and the reagent stream contains 2% (w/v) potassium iodine and 0.4% (w/v) tetramethylenebis(triphenylphosphonium) bromide. The injection rate is 20 h^-1. The calibration graph is linear up to 20 μ ml^-1 bismuth and the detection limit is 0.24 μ ml^-1 bismuth, based on injection volumes of 250μl. The system has been applied to determination of bismuth in pharmaceutical samples.     

Chromatographic separation of rare-earths by cation exchange

A simple relationship expressing the dependence of elution peak position shifts on change in eluant pH is developed for rare-earth ion-exchange separations using α-hydroxy-isobutyric,a-hydroxya-methyl butyric and lactic acids as eluants.     

Separation and analysis of aluminium(III) by cation exchange ion chromatography

A method for the determination of aluminium(III) ions based on separation by cation exchange column chromatography and detection by conductivity detector has been developed. It is fast and reliable, and can be used for the separation and analysis of aluminium(III) ions from other metal ions like Mg(II), Mn(II), Zn(II), Co(II), Ca(II), Sr(II), rare earth elements like Lu(III), Tm(III), and Gd(III), which are eluted at different times and so do not interfere. Effect of p-phenylene diamine concentration present in the eluent, presence of other metal ions and effect of various anions present in the injection sample on the separation and analysis of aluminium(III) ions have also been studied.     

Selective detection of bismuth(III) and iron(II) ions with certain new reagents

Isoperthiocyanic acid (3-amino-5-thione-1,2,4-dithiazole) (I), tetraethylthiuram monosulphide ("Tetmosol") (II), eosin (III), and mercurochrome (IV) are used as new qualitative reagents for bismuth, III and IV are also used for detection of iron(II). A conc. sulphuric acid solution of I, or an acctone solution of II, when treated with bismuth in presence of potassium iodide, gives a deep red or reddish-orange precipitate, characteristic of bismuth. Bismuth in presence of III or IV gives a heavy and characteristically bright deeppink precipitate on addition of ammonia. With I, 1 mug of bismuth may be detected with a dilution limit of 1:50,000. Sb(III) and As(III) do not interfere in any of these tests. Iodides interfere only when I and II are used as reagents. Pb, Cu(II). and Fe(III) interfere with III and IV. I and II are also proposed as reagents for iodide; nitrites would interfere. III and IV, with iron(II) on addition of ammonia, produce a precipitate with highly intense green fluorescence. No other common cation [including Fe(III)] or anion interferes. The limit of detection is 3 mug ml .     

Thermal decomposition of hydrotalcitewith hexacyanoferrate(II) and hexacyanoferrate(III) anions in the interlayer

The thermal decompositions of hydrotalcites with hexacyanoferrate(II) and hexacyanoferrate(III) in the interlayer have been studied using thermogravimetry combined with mass spectrometry. X-ray diffraction shows the hydrotalcites have a d(003) spacing of 11.1 and 10.9 Å which compares with a d-spacing of 7.9 and 7.98 Å for the hydrotalcite with carbonate or sulphate in the interlayer. XRD was also used to determine the products of the thermal decomposition. For the hydrotalcite decomposition the products were MgO, Fe₂O₃ and a spinel MgAl₂O₄. Dehydration and dehydroxylation take place in three steps each and the loss of cyanide ions in two steps.     

Oxidimetric determination of indigo with iron(III) and hexacyanoferrate(III)

The use of iron(III) in sulphuric acid medium and of potassium hexacyanoferrate(III) in hydrochloric acid medium has been investigated for the oxidimetric determination of indigo and indigo sulphonic acid. Conditions have been established for the assay of the dye with iron(III) sulphate at 100 degrees and with potassium hexacyanoferrate(III) at room temperature.     

Thin-layer chromatographic separation of rhodium(III) and iridium(III, IV) by anion exchange

Summary The TLC behaviour of Rh(III), Ir(III) and Ir(IV) has been investigated in the two systems consisting of DEAE-cellulose or ECTEOLA-cellulose and 5 M HCl media containing H₂O₂. These systems, especially in combination with a simple chemical pretreatment of samples (with LiCl, HCl and H₂O₂), can effectively be applied to the complete separation of mixtures of Rh(III) and Ir(III) or Ir(IV) in a wide range of ratios and amounts (Rh: Ir=1100 to 1001).

---

Dünnschicht-chromatographische Trennung von Rhodium(III) und Iridium(III, IV) durch Anionenaustausch

Zusammenfassung Das dünnschicht-chromatographische Verhalten von Rh(III), Ir(III) und Ir(IV) wurde in H₂O₂-haltiger 5 M salzsaurer Lösung auf DEAE-sowie ECTEOLA-Cellulose untersucht. In Kombination mit einer einfachen chemischen Vorbehandlung der Probe (mit LiCl, HCl, H₂O₂) kann eine wirkungsvolle Trennung von Rh(III) und Ir(III) oder Ir(IV) über einen weiten Konzentrationsbereich erzielt werden (Rh: Ir=1100 bis 1001).

     

Thermal decomposition of hydrotalcite with hexacyanoferrate(II) and hexacyanoferrate(III) anions in the interlayer

The mechanism for the decomposition of hydrotalcite remains unsolved. Controlled rate thermal analysis enables this decomposition pathway to be explored. The thermal decomposition of hydrotalcites with hexacyanoferrate(II) and hexacyanoferrate(III) in the interlayer has been studied using controlled rate thermal analysis technology. X-ray diffraction shows the hydrotalcites have a d(003) spacing of 10.9 and 11.1 Å which compares with a d-spacing of 7.9 and 7.98 Å for the hydrotalcite with carbonate or sulphate in the interlayer. Calculations show dehydration with a total loss of 7 moles of water proving the formula of hexacyanoferrate(II) intercalated hydrotalcite is Mg₆Al₂(OH)₁₆[Fe(CN)₆]_0.5·7H₂O and 9.0 moles for the hexacyanoferrate(III) intercalated hydrotalcite with the formula of Mg₆Al₂(OH)₁₆[Fe(CN)₆]_0.66·9H₂O. CRTA technology indicates the partial collapse of the dehydrated mineral. Dehydroxylation combined with CN unit loss occurs in two isothermal stages at 377 and 390°C for the hexacyanoferrate(III) and in a single isothermal process at 374°C for the hexacyanoferrate(III) hydrotalcite.     

Rhodium(III) catalyzed oxidation of cyclic ketones by alkaline hexacyanoferrate(III)

The kinetics of the oxidation of 2-methyl cyclohexanone and cycloheptanone with Fe(CN)₆ ³⁻ catalyzed by RhCl₃ in alkaline medium was investigated at four temperatures. The rate follows direct proportionality with respect to lower concentrations of hexacyanoferrate(III) ion, but tends to become zero order at higher concentrations of the oxidant, while the reaction shows first-order kinetics with respect to hydroxide ion and cyclic ketone concentrations. The rate shows a peculiar nature with respect to RhCl₃ concentrations in that it increases with increase in catalyst at low catalyst concentrations but after reaching a maximum, further increase in concentration retards the rate. An increase in the ionic strength of the medium increases the rate, while increase in the Fe(CN)₆ ⁴⁻ concentration decreases the rate.