Spectrophotometric determination of traces of nitrite with rhodamine 6 G

A simple and highly selective spectrophotometric method is described for the determination of nitrite. The method is based on the measurement of decrease in absorbance at 525 nm of rhodamine 6 G in sulphuric acid medium. The decrease in absorbance is instantaneous on addition of nitrite and remains stable for 2 h. Linear calibration graph passing through the origin was obtained in the range 0.01–0.6 g/ml nitrite. The method is free from interference of Cu²⁺, Fe³⁺ and SO ₃ ^2– which normally interfere in other procedures. The method was applied successfully to the determination of nitrite in well and sea water samples and in KNO₃, NaNO₃, table salt, sugar and milk powder samples.     

Flow-Injection Spectrophotometric Determination of Hydrazine

A flow-injection spectrophotometric method for the determination of hydrazine is described. The method is based on the inhibitory effect of hydrazine on the reaction of thionine with nitrite in acidic media. The decolorization of thionine by the reaction with nitrite was used to monitor the reaction spectrophotometrically at 602 nm. The variables that affected the reaction rate were fully investigated and the optimum conditions were established. Hydrazine can be determined in the range 2.0–40.0 μg/ml with a limit of detection of 1.0 μg/ml. The relative standard deviation for 10 replicate determinations of 7.0 μg/ml hydrazine is 3.3%. The method is simple, rapid, and widely applicable.     

Fluorometric determination of nitrite with acetaminophen

A simple, sensitive and selective fluorometric method for the determination of nitrite is described. The fluorometric determination is based on the reaction of acetaminophen with nitrite in an acidic medium followed by alkalinization of the reaction which yields a highly fluorescent product, exhibit (λ_ex/λ_em=325/430 nm). The optimum experimental conditions were studied. The fluorescene intensity is linear over a nitrite concentration of 0.08–1.3 μg/ml with a detection limit of 2.7 ng/ml (S/N=3). The effect of interferences from various metals/ions were studied. The proposed method is accurate, reproducible, shows satisfactory results and compares successfully with the reference method.     

A new and sensitive resonance-scattering method for determination of trace nitrite in water with rhodamine 6G

In the medium HCl–KI–rhodamine dye, NO₂^– reacts with excess I^– to form I₃^– and the I₃^– and rhodamine dye combine to form an association particle which gives three resonance-scattering (RS) peaks at 320 nm, 400 nm, and 595 nm. In systems containing rhodamine 6G (Rh6G), rhodamine B (RhB), rhodamine S (RhS), and butyl rhodamine B (BRhB) the resonance scattering intensity at 400 nm is proportional to nitrite concentrations in the range 2.3–276 ng mL^–1, 9.2–184 ng mL^–1, 9.2–184 ng mL^–1, and 9.2–92 ng mL^–1, respectively. Because of the high sensitivity, wide linear range, and good stability of the Rh6G system, it has been used for determination of nitrite in water samples, with satisfactory results. The spectral results have been used to verify that the formation of (Rh6G·I₃)_n association particles and their interface with the system are main factors that cause the RS enhancement.     

A Fluorescence Quenching Method for the Determination of Nitrite with Indole

A new fluorescence quenching method has been developed to determine nitrite in water and food samples. The method is based on the reaction between nitrite and the fluorescent indole to form a compound which has no fluorescence in acidic medium. The fluorescence intensity was measured in 1 cm quartz cell with excitation and emission wavelengths of 285 and 350 nm, respectively. The relationship was obtained between the fluorescence intensity and nitrite concentration in the range 0.01–0.6 μg ml⁻¹. The detection limit was 2.5 ng ml⁻¹. The proposed method was applied to determine nitrite in water and food samples. The mechanism involved in the reaction was studied.     

A new selective reagent for the spectrofluorometric determination of beryllium

The fluorescence properties of the beryllium and aluminum complexes with 2, 4-dioxo-4-(4-hydroxy-6-methyl-2-pyrone-3-yl) butyric acid ethyl ester (Ligand) were studied and optimal conditions for their fluorometric determination were established. Beryllium can be determined in the linearity range of 0.5–2.0 μg/ml and aluminum 0.5–1.5 μg/ml. The effect of diverse ions on the determination of beryllium is discussed.A simple procedure for the fluorometric determination of beryllium in human blood plasma in the concentration range of 5–50 μg Be/ml is described.     

Determination of cerium in rare earth ores by fluorescence quenching of rhodamine 6G

A fluorescence quenching method has been developed to determine cerium with rhodamine 6G. The method is based on the oxidation of rhodamine 6G by cerium(IV) in sulfuric acid solution. The linear calibration range is 4.0 × 10^–7 -1.6 × 10^–6mol/L. The detection limit is 1.0 × 10^–7 mol/L. The relative standard deviation was 1.0% (n = 5). The method has been used to determine cerium in rare earth ores, with satisfactory results. The method offers the advantages of simplisity, sensitivity and selectivity.     

Determination of Osmium(VIII) by Flow Injection-Kinetic Methods Using Bromopyrogallol Red and Hydrogen Peroxide

A new flow injection-kinetic method has been developed for the determination of trace amount of osmium(WI), based on its catalytic effect on the bromopyrogallol red and hydrogen peroxide reaction. The reaction is followed spectrophotometrically by measuring the decrease in absorbance at 559 nm. The calibration graph for osmium(VIII) is linear over the range from 0.0040 to 0.10 μg/ml and the detection limit and sampling frequency are 0.0030 μg/ml and 47 per hour, respectively. The proposed method was applied to the determination of trace amounts of osmium in refined ores and chlorination residues with satisfactory results.     

Cytotoxic and apoptotic effects of Hypericum androsaemum on prostate adenocarcinoma (PC-3) and hepatocellular carcinoma (Hep G2) cell lines with identification of secondary metabolites by LC-HRMS

The study aims to determine the secondary metabolites of Hypericum androsaemum L. extracts by liquid chromatography-high resolution mass spectrometry (LC-HRMS), and investigate the antioxidant and cytotoxic activities of the plant. Cytotoxic activity was evaluated by MTT assay, and apoptosis induction abilities on human prostate adenocarcinoma (PC-3), and hepatocellular carcinoma (Hep G2) cell lines. Accordingly, major secondary metabolites were found as hederagenin (762 ± 70.10 μg/g) in the leaves dichloromethane (LD), herniarin (167 ± 1.50 μg/g) in fruit dichloromethane (FD), (-)-epicatechin (6538 ± 235.36 μg/g) in the leaves methanol (LM), (-)-epigallocatechin gallate (758 ± 20.46 μg/g) in the fruit methanol (FM), and caffeic acid (370 ± 8.88 μg/g) in the fruit water (FW), and (3313 ± 79.51 μg/g) in the leaves water (LW) extracts. LM exerted strong antioxidant activity in DPPH free (IC₅₀ 10.94 ± 0.08 μg/mL), and ABTS cation radicals scavenging (IC₅₀ 9.09 ± 0.05 μg/mL) activities. FM exhibited cytotoxic activity with IC₅₀ values of 73.23 ± 3.06 µg/mL and 31.64 ± 2.75 µg/mL on PC-3 and Hep G2 cell lines, respectively. Being the richest extract in terms of quillaic acid (630 ± 18.9 μg/g), which is a well-known cytotoxic triterpenoid with proven apoptosis induction ability on different cells, FM extract showed apoptosis induction activity with 64.75% on PC-3 cells at 50 μg/mL concentration. The study provides promising results about the potential of Hypericum androsaemum on cancer prevention.     

Indirect kinetic microdetermination of oxalate, citrate, and fluoride ions

An indirect catalytic method for the separate microdetermination of oxalate, citrate, and fluoride ions is described. The method is based on the inhibition action of oxalate, citrate, and fluoride ions on the catalytic oxidation reaction of 2,4-diaminophenol-hydrogen peroxide by iron(III).Procedures for the determination of 1.76 × 10⁻² to 17.6 × 10⁻² μg/ml for oxalate ion, 3.78 × 10⁻² to 30.24 × 10⁻² μg/ml for citrate ion, and 0.38 to 4.18 μg/ml for fluoride ion are given.Quantities of 1.76 × 10⁻² to 17.6 × 10⁻² μg/ml for oxalate ion, 3.78 × 10⁻² to 30.24 × 10⁻² μg/ml for citrate ion, and 0.38 to 4.18 μg/ml for fluoride ion could be determinated with a relative error of about 1–3.5% for oxalate and citrate ions and 1–2% for fluoride ion.     

Determination of chromium in waste-water and cast iron samples by fluorescence quenching of rhodamine 6G

A new simple, selective and sensitive fluorescence quenching method was developed to determine chromium with rhodamine 6G. The method is based on the oxidation of rhodamine 6G by chromium(VI) in sulfuric acid solution. The linear calibration graph was obtained in the range 8-80 ng ml(-1) chromium(VI). The detection limit is 0.8 ng ml(-1). The method was applied successfully to the determination of chromium in waste water and cast iron samples.     

Brilliant cresyl blue as a new red region fluorescent probe for determination of nucleic acids

A fluorescence quenching method was developed for determination of microamounts of nucleic acids by using brilliant cresyl blue (BCB) as a new red region fluorescent probe. In aqueous hexylmethylene tetramine solution, BCB showed maximum excitation and emission wavelengths at 626 and 670 nm, respectively, and the fluorescence of BCB could be greatly quenched by DNA (or RNA). Under optimal conditions, the calibration graphs are linear over the range of 0.02–0.80 μg/ml for SM DNA and 0.25–1.5 μg/ml for yeast RNA. The corresponding detection limits are 7 ng/ml for SM DNA and 25 ng/ml for yeast RNA, respectively. SM DNA can be determinated in the presence of 40% (w/w) RNA, and the relative standard deviation of six measurements is 2.5% for 500 ng/ml SM DNA. The result of the determination of golden staphylococcus DNA by this method was satisfactory.     

Immunomodulatory Responses of Two Synthetic Peptides against Salmonella Typhimurium Infection

In vitro assays of phagocytic activity showed that the peptide Pin2[G] stimulates phagocytosis in BMDM cells from 0.15 to 1.25 μg/mL, and in RAW 264.7 cells at 0.31 μg/mL. In the same way, the peptide FA1 induced phagocytosis in BMDM cells from 1.17 to 4.69 μg/mL and in RAW 264.7 cells at 150 μg/mL. Cytokine profiles of uninfected RAW 264.7 showed that Pin2[G] increased liberation TNF (from 1.25 to 10 μg/mL) and MCP-1 (10 μg/mL), and FA1 also increased the release of TNF (from 18.75 to 75 μg/mL) but did not increase the liberation of MCP-1. In RAW 264.7 macrophages infected with Salmonella enterica serovar Typhimurium, the expression of TNF increases with Pin2[G] (1.25–10 μg/mL) or FA1 (18.75–75 μg/mL). In these cells, FA1 also increases the expression of IL-12p70, IL-10 and IFN-γ when applied at concentrations of 37.5, 75 and 150 μg/mL, respectively. On the other hand, stimulation with 1.25 and 10 μg/mL of Pin2[G] promotes the expression of MCP-1 and IL-12p70, respectively. Finally, peptides treatment did not resolve murine gastric infection, but improves their physical condition. Cytokine profiles showed that FA1 reduces IFN-γ and MCP-1 but increases IL-10, while Pin2[G] reduces IFN-γ but increases the liberation of IL-6 and IL-12p70. This data suggests a promising activity of FA1 and Pin2[G] as immunomodulators of gastric infections in S. Typhimurium.     

Solid Phase Extraction and Spectrophotometric Determination of Silver with 2-(2-Quinolylazo)-5-Dimethylaminophenol

A new chromogenic reagent, 2-(2-quinolylazo)-5-Dimethylaminophenol (QADMAP) was synthesized, and a sensitive, selective, and rapid method was developed for the determination of the μg/L level of silver ions. The method is based on the rapid reaction of silver(I) with QADMAP and the solid phase extraction of the colored chelate using a C₁₈ cartridge. The QADMAP reacts with Ag(I) in the presence of a citric acid-sodium hydroxide buffer solution (pH 5.0) and a sodium dodecyl sulfonate (SDS) medium to form a violet chelate of molar ratio 1 : 2 (silver to QADMAP). This chelate was enriched by solid phase extraction with C₁₈ cartridge, and the retained chelate was eluted from the cartridge using ethanol (with 1% acetic acid). In the ethanol medium (with 1% acetic acid), the molar absorptivity of the chelate was 1.25 × 10⁵ L mol⁻¹ cm⁻¹ at 584 nm. Beer’s law was obeyed in the range 0.01–0.6 μg/mL. The relative standard deviation for eleven replicate samples of 0.01 μg/mL was 1.86%. The detection limit is 0.02 μg/L in the original samples. The method was applied to the determination of μg/L levels of silver ions in water with good results.__________From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 6, 2005, pp. 566–570.Original English Text Copyright © 2005 by Huang, Yang, Hu, Yin.This article was submitted by the authors in English.     

Comparison of three post-column reaction methods for the analysis of bromate and nitrite in drinking water

Three post-column ion chromatographic methods (i.e., a sodium bromide–sodium nitrite method, an o-dianisidine method, and a potassium iodide–ammonium heptamolybdate method) were compared for bromate and nitrite analysis. Also, the effect of direct mixing of the reagents without ion suppressors for the sodium bromide–sodium nitrite method and the potassium iodide–ammonium heptamolybdate method was investigated. For the analysis of bromate, the three methods showed similar method detection limits (0.17–0.24 μg/l) with pneumatic reagent delivery systems. Direct reagent mixing achieved comparable detection limits to the suppressor configuration. The three methods are also compatible with conductivity detection. When used in combination with conductivity detection, this compatibility allows simultaneous analysis of bromate, nitrite, and other common ions in drinking water, such as bromide. It was found that the o-dianisidine method achieves μg/l-level detection of nitrite and bromate with a simpler configuration than the potassium iodide–ammonium heptamolybdate method, while the sodium bromide–sodium nitrite method was not sufficiently sensitive for nitrite analysis at the μg/l level.     

Catalytic microdetermination of iron

A reaction rate method is described for the microdetermination of iron. The method is based on the catalytic action of iron on the reaction of 2,4-diaminophenol with hydrogen peroxide. The effect of reagent concentration is studied and the maximum tolerable amounts of interfering ions are determined. Procedures for the determination of 2.8 × 10⁻³ to 2.8 × 10⁻² μg/ml are given.Quantities of 2.8 × 10⁻³ to 2.8 × 10⁻² μg/ml could be determinated with a relative error of about 2%.     

Sensitive determination of nitrite by means of a Landolt-type reaction in fluorescent aggregates of a binaphthyl-based amphiphile

The iodine quenching effect on the fluorescence of a binaphthyl-based amphiphile, C₈BNC₆N, was used for monitoring the Landolt-type reaction between nitrite, iodide, and thiosulfate. Due to the possibility of iodine detection in the 10^–8–10^–7 M range, and to the effective concentration of anionic reagents on the surface of cationic aggregates, the indicator reaction can be monitored using reagents at concentration levels as low as 10^–7 M. To optimize the analytical system, the effect of pH and reagent concentrations on the rate of indicator reaction were studied. The influence of the matrix of water samples and effect of side-reactions increasing the value of a blank test were examined. A procedure for nitrite determination in water was developed, using the diazo reaction for selective nitrite removal to provide a reference solution, which avoided possible effects of the matrix components. The usefulness of this method was tested by determining trace amounts of nitrite in water samples. The procedure allows determination of nitrite down to 5 ng/ml (detection limit about 2ng/ml) with r.s.d. of 10% in the 20–250 ng/ml range.     

A novel method for the spectrophotometric determination of nitrite in water

A rapid, simple, selective and sensitive method for the spectrophotometric determination of nitrite in water has been developed and optimum reaction conditions along with other analytical parameters have been evaluated. Nitrite reacts with barbituric acid in acidic solution to give the nitroso derivative, violuric acid. At analytical wavelength of 310 nm, Beer's law is obeyed over the concentration range 0.00–3.22 ppm of nitrite. The molar absorptivity is 15330 ± 259.7 (95%) with pooled standard deviation of 355.57 and R.S.D. of 2.32%. As well as the method is sensitive (2.99 × 10⁻³ μg NO₂ cm⁻²) and selective, it tolerates most of the potential interferents. It has been successfully applied to nitrite determination in natural waters by use of a calibration graph with determination limit of 1.66 μg NO₂ in 100 mL working solution corresponding to minimum 9.5 ppb NO₂–N in water samples. Lower concentrations of nitrite (3.0 μg NO₂/L sample) is precisely analyzed by using the method of dilution with sample, with R.S.D. of lower than 0.5%. The results were compared with standard N-(1-naphtyl)ethylenediamine dihydrochloride method and very good agreement between the data was observed. The method can easily be applied in the field.     

Microdetermination of silver(I) and iodide ions with a pyridinol azo dye: A spectrophotometric method

A simple, rapid, sensitive, and selective method for the spectrophotometric microdetermination of silver(I) using ammonium(2′,3′-dihydroxy pyridyl-4′-azo)benzene-4-arsonate (DHP-4A), a water soluble pyridinol azo dye is proposed. The red colored 1:1 (metal to ligand) complex formed has molar extinction coefficient (ε) 2.95 × 10⁴ 1 mol⁻¹ cm⁻¹ and absorbs maximum at 535 nm, in highly alkaline medium. Beer's law is obeyed up to 3.36 ppm and Sandell's sensitivity (for an absorbance 0.001) is 0.0037 μg of Ag(I)/cm². The silver(I)-(DHP-4A) complex has also been used in the microdetermination of iodide ions using ligand exchange reaction. The optimum concentration range of iodide ions which can reproducibly be determined is 1.27–37.9 μg/10 ml.     

Simultaneous determination of chloride, nitrate and sulphate in vegetable samples by single-column ion chromatography

A new ion chromatography method is described for the simultaneous determination of Cl⁻, NO₃⁻ and SO₄²⁻, using a selected eluent 1.3-mM sodium gluconate/1.3-mM borax (pH 8.5). The extraction methods of Cl⁻, NO₃⁻, SO₄²⁻ in vegetables are studied. The determination limits of Cl⁻, NO₃⁻, SO₄²⁻ are 0.17 μg/ml, 0.63 μg/ml and 0.81 μg/ml. The linear ranges are 060 μg/ml, 090 μg/ml and 090 μg/ml. The relative S.D. are <2.5%. The mean recoveries of Cl⁻, NO₃⁻, SO₄²⁻ in vegetables range from 97.0 to 104%.