石墨炉原子吸收法测定食品添加剂甲壳素中的镉和铅

采用程序控制温度,一次完成甲壳素样品的炭化和灰化,通过氢氟酸-硝酸消除灰分中硅的干扰,用石墨炉原子吸收法直接测定其中的镉和铅.镉的浓度在0～50 ng/mL范围内与吸光度呈良好的线性关系,相关系数r= 0.9990;铅的浓度在0～300 ng/mL范围内与吸光度呈良好的线性关系,相关系数r=0.9990 .镉的回收率为90.6%～102.0%,测定结果的相对标准偏差为4.37%(n=8);铅的回收率为91.3%～102.1%,测定结果的相对标准偏差为8.67%(n=8).     

石墨炉原子吸收光谱法测定新疆出口番茄酱中的铅和镉

报道了微波消解石墨炉原子吸收光谱法测定番茄酱中的铅、镉。研究了石墨炉原子吸收测定的最佳条件。该方法测定铅和镉的线性范围分别为0.00~25 ng/mL、0.00~8 ng/mL;相对标准偏差分别为2.15%、3.10%;回收率分别为98.6%、104.5%。利用国家标准物质番茄叶(ESP-1)验证了方法的准确度,测定值与标准值基本吻合。研究表明,该方法具有很好的准确度和精密度。     

纳米Al2O3微柱分离/富集-石墨炉原子吸收法测定环境试样中的痕量铅和镉

本文将纳米氧化铝微柱分离系统与石墨炉原子吸收光谱法联用,用于测定环境水样中的痕量铅和镉。较系统地考察了纳米Al2O3材料对镉和铅离子的吸附性能及影响因素;在优化的实验条件下本法对Pb和Cd的检出限(3σ)分别为0.189 ng/mL和0.0039 ng/mL;RSD%分别为3.9%和2.9%。     

微波消解-石墨炉原子吸收法测定酵母粉中的微量铅和镉

本文采用微波消解-石墨炉原子吸收法直接测定酵母粉中微量铅和镉的含量。利用硝酸和过氧化氢消解样品,对微波消解的条件,基体改进剂的选择,铅原子化温度的效果以及常见元素对测定的干扰进行了研究。在优化的实验条件下,方法对铅和镉的检出限(3σ)分别为0.062 ng/mL和0.013 ng/mL,相对标准偏差(RSD)分别为0.64%~1.11%、0.75%~4.70%,加标回收率在95.00%~102.0%之间。本法已用于酵母粉中微量铅和镉的测定,分析结果与电感耦合等离子体-质谱(ICP-MS)法具有良好的一致性。     

螺旋藻中铅镉的ICP-MS测定

采用微波消解、高压罐消化以及HNO3 HClO4消化3种方法对螺旋藻样品进行处理,比较了不同方法产生的空白值和加标回收率。建立了微波消解-电感耦合等离子体质谱法测定螺旋藻样品中的铅镉的方法。铅镉检出限分别为0.06ng mL和0.05ng mL,RSD均小于3%,加标回收率在98%～101%之间。方法用于实际样品分析。     

顶空固相微萃取-气相色谱质谱联用测定烷基铅的研究

建立了顶空固相微萃取(HS SPME)与气相色谱 质谱(GC/MS)联用测定水样中四甲基铅和四乙基铅的方法,探讨了SPME萃取烷基铅的实验条件,并对GC/MS条件进行了优化。结果表明:四甲基铅和四乙基铅分别在5～1000ng/mL和1～500ng/mL范围内有良好的线性关系,检出限分别为四甲基铅5.19ng/mL,四乙基铅1.05ng/mL。方法用于合成水样分析,四甲基铅和四乙基铅的回收率在87.5%～110.6%之间,相对标准偏差在1.7%～6.5%之间。     

间断多次扫描电位溶出分析方法的研究

间断多次扫描电位溶出分析是在多次扫描电位溶出分析和间断扫描伏安法的基础上提出的一种新的电位溶出分析技术,它不仅具有多次扫描电位溶出分析灵敏度高的优点,又克服了多次扫描电位溶出分析对多元素分析时元素之间相互干扰的缺点。文章讨论了间断多次扫描电位溶出分析的实验条件,同时用这种方法分析了人尿中镉、铅的含量。间断多次扫描电位溶出分析在电积10分钟时,最低可检测到0.005ng/mL的镉和0.01ng/mL的铅。镉、铅浓度为4ng/mL时,相对标准偏差分别为2.9%和3.2%,证明间断多次扫描电位溶出分析可以同脉冲阳极溶出伏安法媲美。     

微波消解样品-石墨炉原子吸收光谱法测定蜂产品中铅、镉、硒

提出了石墨炉原子吸收光谱法测定4种蜂产品中硒、铅和镉的含量.样品用浓硝酸、过氧化氢浸泡后,加热溶解,补加浓硝酸、过氧化氢进行微波消解.在优化的石墨炉工作条件下,用磷酸二氢铵作基体改进剂测定铅和镉,用PdCl2和Mg(NO3)2作混合基体改进剂测定硒.铅、镉和硒的检出限(3S/N)分别为11.3,1.9,3.7 ng,应用此方法分析了4种蜂产品样品,并用标准加入法作回收试验,测得铅、镉、硒的回收率分别为95.4%～103.8%,89.0%～110.0%,86.8%～96.5%之间,相对标准偏差均小于6%.     

双硫腙修饰纳米TiO2分离富集石墨炉原子吸收光谱法测定水样中痕量金属离子

建立了双硫腙修饰纳米TiO2分离富集-石墨炉原子吸收光谱法测定水样中痕量镉、铬和铅的新方法,优化了纳米TiO2-双硫腙对试样中这3种痕量物质的吸附和解吸条件。结果表明,在pH 5.0时,镉、铬和铅可被定量吸附,静态饱和吸附容量分别为13.3、5.5、21.8 mg/g。吸附的各种金属离子可用5 mL 0.1mol/L的硝酸完全洗脱。该方法对Cd2+、Cr3+和Pb2+的检出限(3σ,n=11)分别为0.18、0.51、1.92 ng/L,相对标准偏差分别为2.8%、2.3%和1.0%,加标回收率为96%～101%。该方法已成功应用于环境水样中镉、铬和铅的测定。     

悬浮液进样-石墨炉原子吸收光谱法测定巴戟天中痕量铅和镉

取经烘干粉碎并通过0.074mm网筛的巴戟天样品0.050 0g,加入琼脂溶液10.0mL(其中含磷酸二氢铵0.1g,作为基体改进剂),超声振荡5min,制成样品的悬浮液,直接进样,采用石墨炉原子吸收光谱法测定其中铅和镉的含量。设置铅和镉的灰化温度分别为850℃和800℃。结果表明:铅和镉的质量浓度在一定范围内与其吸光度呈线性关系,铅和镉的检出限(3s×V/b)分别为2.17×10-9 mg和3.4×10-10 mg。按照标准加入法进行加标回收试验,铅和镉的回收率分别在98.8%～103%和98.3%～104%之间。精密度试验表明铅和镉的测定值的相对标准偏差(n=7)分别为2.7%和1.2%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.