流动分析-离子选择电极法测定水中痕量氟化物

基于流动分析-离子选择电极技术,建立了一种测定水中痕量氟化物的分析方法。体系使用注射泵将注入的样品推出,在稳态的条件下进行测定。样品与总离子强度缓冲溶液(TISAB)等体积混合后,采用蠕动泵注入样品,注入量为400L。采用注射泵驱动载流速度快,比蠕动泵效果好。载流为0.05mg/L F-标准溶液,采用奥立龙(Orion)电极,倾斜20°的喷壁型(Wall-jet)流通池。样品之间插入清洗,方法没有交叉携出。在最佳的条件下,方法的线性范围为0.05～1.0mg/L,检出限为0.015mg/L,RSD为1.5%(0.2mg/L)。样品分析频率为30样/h。本方法对质控样品的测定结果令人满意。3个水样的加标回收率为96.8%～104.5%。用4个水样与国标中的手工分析方法进行了对比,在95%的置信区间内,配对t检验结果无显著差异。本方法灵敏度高,分析速度快、试剂消耗少,废液排放量低,适用于水中低浓度样品的分析。     

氟电极法测定氟化物的改进

氟离子选择电极测定氟化物时,加入20%(体积比)的二噁烷溶剂,与单一水溶剂相比,可降低测定下限,提高电位。     

超声提取-离子选择电极法测定铝渣中的氟化物

目前铝渣中的氟化物对环境的影响已经成为人们关注重点之一。为了能够准确测定铝渣中的氟化物含量,实验对超声时间、固液比以及Al~(3+)和Ca~(2+)同时存在下的干扰进行了研究。确定了最佳超声时间为20min,以固液比为1∶20进行超声提取,提取液移取体积为5mL,加入总离子强度溶液15mL的方法来消除质量浓度不大于25mg/L Al~(3+)和Ca~(2+)的干扰,运用离子选择电极法准确测定铝渣中的氟化物,得到标准曲线线性相关系数为0.999 9,方法检出限为0.3mg/kg,相对标准偏差(n=6)小于2%,加标回收率在90.8%～108%。同时用超声提取法对样品进行前处理,分别运用离子选择电极法和离子色谱法对铝渣中的氟化物进行测定,两者测定结果一致,方法的准确度良好。     

离子选择电极法测定生活饮用水中氟化物

采用离子选择电极法对生活饮用水中氟化物浓度进行了测定。讨论了水样中pH值、温度、响应时间对测定结果的影响。在最佳条件下,方法的线性范围为0．10～3．0mg／L,相关系数为0．9999,检出限为0．05mg／L,实际水样加标回收率为97％～106％,相对标准偏差（n=5）为0．04％～0．65％。方法简单快速,干扰小,重现性好,加标回收率令人满意,能进行生活饮用水中氟化物浓度的有效测定。     

离子选择电极法测定水中氯含量

采用离子选择电极法建立了一种对水中氯进行测定的方法。通过加入柠檬酸三钠-硝酸钾作为总离子强度调节剂,以氢氧化钠与硝酸调节溶液的pH值为5左右,用离子计测量氯离子的电位值,并用格氏作图法于半对数曲线查得氯含量,提高了测量的稳定性、灵敏性和准确性。水中氯的测定范围为5～50μg/mL,加标回收率为93%～105%。     

离子选择电极法和新氟试剂光度法测定空气中HF的比较

对离子选择电极法与新氟试剂光度法的特性指标进行了比对研究。结果表明,离子选择电极法检出限为0.01 mg/L,线性范围为0.04～1 900 mg/L,相对标准偏差为0.16%～0.30%,加标回收率为101%;新氟试剂光度法检出限为0.05 mg/L,线性范围为0.06～1.5 mg/L,相对标准偏差为1.05%～2.10%,加标回收率为105%。两种方法结果无显著性差异,但离子选择电极法与新氟试剂光度法相比,测定下限低,测定范围宽,精密度、准确度较高,因此选定离子选择电极法作为制定大气中氟化氢测定法国家标准的基础。     

高分辨连续光源原子吸收光谱法对土壤中磷的测定

磷元素在适宜的空气-乙炔火焰中可形成PO双原子分子,PO分子的部分吸收谱线具有原子谱线的轮廓和强度.该文主要研究了利用连续光源原子吸收光谱法,在空气-乙炔火焰条件下测定PO分子的吸光度值,从而测定土壤样品中的磷元素.实验研究了测定过程中可能存在的光谱干扰和化学干扰、乙炔/空气流速比、燃烧器高度对PO双原子分子吸光度的影响,以及不同消解方式对测定结果的影响.在优化的实验条件下,PO 246.40 nm的检出限为20 mg/L.通过对土壤标准物质中磷元素含量的测定比对证明,连续光源原子吸收光谱法是一种测定土壤中磷元素含量的简单、快速的方法.     

Determination of Total and Fluoride Bound Aluminium in Tea Infusions by Ion Selective Electrode and Flame Atomic Absorption Spectrometry

ABSTRACT

Speciation of metallic compunds is important especially for their bioavailability. In this present study fluoride bound aluminium species were determined in tea infusion. Total aluminium was measured using flame atomic absorption spectrometry (FAAS). Free fluoride and total fluoride were measured by fluoride selective ion electrode (FISE) with the assistance of TISAB buffer solution used for adjustment of pH and total ionic strength, and ALCOA buffer solution which decomposes all of the Al-fluoride complexes in solution.

During the studies, the effects of pH and time on the formation of Al-F complexes and interference of some metal ions found in tea infusion such as Al³⁺, Mg²⁺, Fe²⁺, Fe³⁺ and Mn²⁺ on the concentration of free fluoride were investigated. The concentration of each Al-fluoride complexes in tea fusion were determined indirectly by calculation using pF-Mole Fraction Diagram. It was found that 1.13±0.15 mg 1^? of 12.00±0.86 mg 1^? total aluminium is fluoride bound aluminium, which means that appoximately 10% of total aluminium in tea infusion is complexed with fluoride.     

离子选择性电极法测定离子液体中的氟离子

旨在探究是否可以利用离子选择性电极法对1-己基-3-甲基咪唑四氟硼酸盐(HmimBF4)离子液体复合材料中的氟离子进行测定。得到线性响应范围是pF值为0.5～5,最适pH值为6,其检出下限为1×10~(-5) mol/L,精密度为0.75%,测得离子液体的氟离子浓度为0.19 mol/L,加标回收率为97.2%～103.2%。结果表明,离子选择性电极法具有实际操作简单、响应时间短、加标回收率高、精密度高、准确度好等优点,所以可用于样品的测定。     

离子交换-原子捕集-火焰原子吸收光谱法测定水中的超痕量镍

在文中所述条件下,镍的原子捕集灵敏度较常规法高320倍,即在离子交换法浓缩仅40倍的情况下,可使镍的测定灵敏度提高12800倍,从而成功实现了ppt级超痕量镍的测定。     

盐酸超声-氟离子选择电极法测定复合肥中氟含量

为快捷有效地测定复合肥中氟的含量,采用盐酸浸取过夜、盐酸超声、碱熔、纯水煮沸四种方法提取复合肥中的氟离子,用氟离子选择电极进行测定,全程加标回收;结果发现盐酸超声提取法测得值与碱熔提取法测定值非常接近,并且加标回收率为98.4%~104.2%,相对标准偏差为1.9%;则用盐酸超声提取法测定复合肥中的氟含量方法可靠,方便快速,能够满足复合肥中氟含量的测试要求。     

Selective Determination of Copper in Water Samples by Atomic Absorption Spectrometry after Cloud Point Extraction

A preconcentration methodology utilizing the cloud point phenomenon is described for the determination of copper by flame atomic absorption spectrometry. The reagent Sulfathiazolylazo resorsin was used as a complexing agent. The preconcentration factor of 25-fold was obtained. The calibration curve is linear in the range of 4–400 µ g L^?1 with a limit of detection of 0.64 µ g L^?1. The relative standard deviation (n = 5, 12 µ g L^?1) was 3.5%. The cloud point is formed in the presence of phenol at room temperature. The method was successfully applied to the determination of copper in water samples and a standard reference material.     

原子吸收光谱和原子发射光谱法测定工业废水中的总铬

为了探讨原子吸收光谱法和原子发射光谱法测定工业废水中的总铬分析方法的异同,分别采用两种方法对工业废水中的总铬进行了对比分析,对样品前处理方法,方法的标准曲线、检出限、准确度、精密度、干扰及消除等进行了比较,并对两种方法的测定结果进行t检验。结果表明,两种方法具有良好的一致性。相对来说,原子发射光谱法各方面指标要优于原子吸收光谱法。     

High-Resolution Continuum Source Atomic Absorption Spectrometry with Microwave-Assisted Extraction for the Determination of Metals in Vegetable Sprouts

The goal of this study was to investigate the enrichment of garden cress (Lepidium sativum), mung beans (Vigna radiata), and soybeans (Glycine max) with minerals. Hydroponic nutrient solutions were enriched with Zn²⁺,Cr³⁺, Ca²⁺, Mg²⁺, and Se²⁺. Morphological assessment was based on monitoring changes that occurred as a function of the concentrations of elements in the medium. The growth of the plant, as a result of a stimulating or inhibitory effect of the identity and concentration of elements on the germination process, was characterized. Microbiological contamination was identified and catabolic profiles of two bacterial strains were performed. High-resolution continuum source atomic absorption spectrometry (HR-AAS) was used to determine Zn²⁺, Cr³⁺, Ca²⁺, Mg²⁺, and Se²⁺ in dried plant material after sample pretreatment using microwave-assisted extraction. The limits of detection were 0.010, 0.029, 0.013, 0.151, and 0.030 milligram per liter for Ca²⁺, Cr³⁺, Mg²⁺, Se²⁺, and Zn²⁺, respectively. Recoveries were higher than 98 percent and the relative standard deviation was less than 5 percent. The accuracy of the procedure was estimated by analyzing certified reference materials. The results showed that biofortification of garden cress by zinc holds the highest promise for the creation of designer foods. Garden cress was found to have the highest bioconcentration factor among the investigated plants; at 50 parts per million, plant growth was stimulated without contamination by microorganisms.     

Determination of Lead in Coal Using Direct Solid Sampling and High-Resolution Continuum Source Graphite Furnace Atomic Absorption Spectrometry

A method has been developed for the determination of Pb in coal using direct solid sampling (SS) and high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS). The certified coal reference materials used in this study were ground in an agate mortar to particle size ≤50 μm. Mass aliquots between 0.1 and 1 mg were weighed onto pyrolytic graphite platforms, and inserted directly into the graphite tube. For pyrolysis temperatures lower than 600 °C, a continuous background due to radiation scattering at solid particles preceded the atomic signal, as the coal matrix could not be sufficiently eliminated under these conditions. An optimized pyrolysis temperature of 700 °C was adopted for Pb without the use of a modifier. The optimum atomization temperature was found to be 1700 °C. Under these conditions, interference-free determination could be performed with calibration against aqueous standards in 0.5% v/v HNO₃. A total of six certified reference coal samples were analyzed, and the results obtained were all in good agreement with certified and informed values, respectively, according to a Student t-test at a 95% confidence level. A detection limit of 0.008 μg g⁻¹ for Pb was obtained at the 217.000 nm resonance line, a value comparable to those obtained by other sensitive, but much more sophisticated techniques, showing that the absence of dilution in the SS-HR-CS GF AAS method allows at least equivalent detection performance.