巯基乙胺稳定的水溶性CdTe纳米粒子的合成与表征

用巯基乙胺(cysteamine，CA)作为稳定剂，在水相中合成了发光可调的CdTe半导体纳米粒子。这些巯基乙胺稳定的CdTe纳米粒子表面带有大量的正电荷。实验结果表明，稳定剂与Cd的比例以及pH等实验条件对CdTe纳米粒子体系的荧光发射强度影响较大。在pH为6.1时，纳米粒子体系在橙红波段的荧光量子产率达到了9%左右。控制实验条件，合成了各种尺寸的CdTe纳米粒子，荧光发射光谱在520～600 nm范围连续可调。分别用X射线光电子能谱(XPS)，透射电子显微镜(TEM)，X射线衍射仪(XRD)，红外吸收     

Synthesis of Aqueous CdTe Nanocrystals with High Efficient Blue‐Green Emission of Exciton

As one of the most popular nanocrystals (NCs), aqueous CdTe NCs have very weak green emission under conventional synthesis conditions. In this work, we report the first example of blue‐emitting CdTe NCs directly synthesized in aqueous solution by slowing down the growth rate after nucleation. The key for the synthesis is the optimization of NC growth conditions, namely pH range of 7.5 to 8.5, TGA/Cd ratio of 3.6, Cd/Te ratio of 10, and Te concentration of 2×10^?5 mol/L, to get a slow growth rate after nucleation. The as‐prepared blue‐emitting CdTe NCs have small size (as small as 1.9 nm) and bright emission [with 4% photoluminescence quantum yield (PL QY) at 486 nm and 17% PLQY at 500 nm]. Transmission electron microscopy (TEM) images of the as‐prepared CdTe show monodispersed NCs which exhibit cubic zinc blend structure. Moreover, time‐resolved PL decay and X‐ray photoelectron spectroscopy (XPS) results show the as‐prepared NCs have better surface modification by ligand, which makes these luminescent small CdTe NCs have higher photoluminescence quantum yield, compared with NCs synthesized under conventional conditions.     

Novel Strategy for Synthesis of High Quality CdTe Nanocrystals in Aqueous Solution

A novel aqueous route for the synthesis of high-quality CdTe nanocrystals（NCs） is presented in this article. With both glutathione（GSH） and cysteine[n（GSH）：n（cysteine）=1：3] as stabilizers, high-quality CdTe NCs with controllable photoluminescence（PL） wavelength from 500 to 630 nm can be prepared within 4 h. As-prepared CdTe NCs show higher photoluminescence quantum yields（PLQY） compared with CdTe NCs prepared via other aqueous methods. When the fluorescent emission peak appeared in orange-red window, the PLQY reaches 70% or above at room temperature without any post-preparative treatment.     

Luminescent properties of water-soluble denatured bovine serum albumin-coated CdTe quantum dots

Chemically reduced bovine serum albumin (BSA) has been used to modify the surface of water-soluble CdTe quantum dots (QDs). It is demonstrated that the denatured BSA (dBSA) can be conjugated to the surface of CdTe QDs and thereby efficiently improve the chemical stability and the photoluminescence quantum yield (PL QY) of the QDs. It is inferred that a shell-like complex structure CdTe(x)(dBSA)(1-x) will form on the surface of the CdTe "core", resulting in the enhancement of PL intensity and the blue shift of the PL peak. This study of the effects of pH and dBSA concentration on optical properties of dBSA-coated QDs suggests that, at pH 6-9, the solution of dBSA-coated CdTe QDs can keep substantial stability and fluorescent brightness, whereas further increase of pH value leads to a dramatic decrease in PL QY and chemical stability. On the other hand, too high or too low initial dBSA concentration in the QD solution results in a decrease of PL QY for dBSA-coated CdTe QDs. This study provides a new approach of preparing stable water-soluble QDs with high PL QY and controllable luminescent colors for biological labeling applications.     

One-pot noninjection synthesis of Cu-doped Zn(x)Cd(1-x)S nanocrystals with emission color tunable over entire visible spectrum

Unlike Mn doped quantum dots (d-dots), the emission color of Cu dopant in Cu d-dots is dependent on the nature, size, and composition of host nanocrystals (NCs). The tunable Cu dopant emission has been achieved via tuning the particle size of host NCs in previous reports. In this paper, for the first time we doped Cu impurity in Zn(x)Cd(1-x)S alloyed NCs and tuned the dopant emission in the whole visible spectrum via variation of the stoichiometric ratio of Zn/Cd precursors in the host Zn(x)Cd(1-x)S alloyed NCs. A facile noninjection and low cost approach for the synthesis of Cu:Zn(x)Cd(1-x)S d-dots was reported. The optical properties and structure of the obtained Cu:Zn(x)Cd(1-x)S d-dots have been characterized by UV-vis spectroscopy, photoluminescence (PL) spectroscopy, transmission electron microscopy (TEM), and X-ray diffraction (XRD). The influences of various experimental variables, including Zn/Cd ratio, reaction temperature, and Cu dopant concentration, on the optical properties of Cu dopant emission have been systematically investigated. The as-prepared Cu:Zn(x)Cd(1-x)S d-dots did show PL emission but with quite low quantum yield (QY) (typically below 6%). With the deposition of ZnS shell around the Cu:Zn(x)Cd(1-x)S core NCs, the PL QY increased substantially with a maximum value of 65%. More importantly, the high PL QY can be preserved when the initial oil-soluble d-dots were transferred into aqueous media via ligand replacement by mercaptoundeconic acid. In addition, these d-dots have thermal stability up to 250 °C.     

水相中CdTe纳米晶的制备及其光学性质

用不同稳定剂(巯基乙酸(TGA)、巯基丙酸(MPA)、L-半胱氨酸(L-Cys)、3-巯基-1,2-丙二醇(TG))在水相中制备了CdTe纳米晶, 并用透射电子显微镜(TEM)、X射线光电子能谱(XPS)和X射线粉末衍射(XRD)等技术对其进行了表征. 研究了不同水相合成条件对CdTe纳米晶光学性质的影响, 结果表明, n(Cd):n(Te)、溶液pH值、回流时间以及稳定剂的性质, 对纳米晶的光学性质具有显著影响. 制得的CdTe纳米晶发射峰窄且对称(半高全宽达38 nm), 用不同稳定剂制备的纳米晶发光量子效率有所不同, 用不同的激发波长对纳米晶进行激发时, 发射峰并未表现出明显的移动.     

水溶性的高荧光CdTe/CdSeⅡ型核壳量子点的合成与表征

用L-半胱氨酸(L-cysteine)作为稳定剂,以制备的CdTe量子点为核模板,水相合成了具有近红外发光的Ⅱ型核壳CdTe/CdSe半导体量子点。实验考察了合成温度,核模板的尺寸和组分比等因素对合成高质量的CdTe/CdSe量子点的影响。用紫外-可见吸收和荧光光谱研究了合成的量子点的光学性质。在优化的合成条件下,荧光发射光谱在586～753nm范围连续可调,荧光量子产率高达68%;通过X-射线衍射(XRD),X射线光电子能谱(XPS)和透射电镜(TEM)对合成的Ⅱ型核壳CdTe/CdSe量子点进行了结构和形貌表征。     

Electrostatic and covalent interactions in CdTe nanocrystalline assemblies

This paper focuses on the interactions between cysteamine-stabilized CdTe nanocrystals [CdTe(CA) NCs] and thioglycolic-acid-stabilized CdTe nanocrystals [CdTe(TGA) NCs]. These interactions were examined by the absorption, continuous, and time-resolved photoluminescence (PL) spectra of the electrostatically mixed and the covalently linked NCs assemblies comprised of the oppositely surface charged CdTe(CA) and CdTe(TGA) NCs and by a comparison with those of the corresponding pristine NCs. The CdTe(CA)-CdTe(TGA) coupling is dictated by the surfactant spacer, ranging between 0.93 and 1.14 nm and by electrostatic and covalent interactions, enabling a F?rster resonance energy transfer (FRET) process among the NCs. The results revealed an excellent spectral overlap between the emission of the CdTe(TGA) NCs and the absorption of the CdTe(CA) NCs as well as a PL spectral red shift on the formation of electrostatic and covalent interactions. Furthermore, the measurements showed a lifetime ranging between 1.2 and 3 ns for the electrostatically mixed and the covalently linked assemblies, shorter than those of the pristine CdTe(CA) NCs and CdTe(TGA) NCs, both of which measured as approximately 5.5 ns. When CdTe(TGA) NCs performed as the most efficient donors, FRET rates of 10(10)-10(11) s(-1) were calculated for the electrostatically mixed NCs or covalently linked NCs.     

Efficient Solid‐State Light‐Emitting CuCdS Nanocrystals Synthesized in Air

Semiconductor nanocrystals (NCs) possess high photoluminescence (PL) typically in the solution phase. In contrary, PL rapidly quenches in the solid state. Efficient solid state luminescence can be achieved by inducing a large Stokes shift. Here we report on a novel synthesis of compositionally controlled CuCdS NCs in air avoiding the usual complexity of using inert atmosphere. These NCs show long‐range color tunability over the entire visible range with a remarkable Stokes shift up to about 1.25 eV. Overcoating the NCs leads to a high solid‐state PL quantum yield (QY) of ca. 55 % measured by using an integrating sphere. Unique charge carrier recombination mechanisms have been recognized from the NCs, which are correlated to the internal NC structure probed by using extended X‐ray absorption fine structure (EXAFS) spectroscopy. EXAFS measurements show a Cu‐rich surface and Cd‐rich interior with 46 % Cu^I being randomly distributed within 84 % of the NC volume creating additional transition states for PL. Color‐tunable solid‐state luminescence remains stable in air enabling fabrication of light‐emitting diodes (LEDs).     

一锅合成绿色到近红外发射的CdTe量子点

以3-巯基丙酸(MPA)为稳定剂,采用水相合成法制备了从绿色到近红外发射的CdTe量子点。系统研究了反应液pH值、镉和碲的物质的量之比及镉和3-巯基丙酸的物质的量之比等实验条件对CdTe量子点体系的发射波长和荧光量子产率的影响。在pH值为10.5,且nCd2+∶nTe2-∶nMPA=1∶0.05∶1.1的条件下,回流0.5 h,CdTe量子点体系在569 nm波长处的荧光量子产率达到30.8%;在7 h的回流时间内,制备的量子点的波长覆盖范围为525～730 nm。分别用X射线粉末衍射、透射电镜和红外光谱对CdTe量子点的晶体结构、形貌及表面基团进行表征。     

Effect of CdS Interlayer on Properties of CdTe Based Quantum Dots

Highly luminescent thioglycolic acid-capped CdTe-based core/shell quantum dots (QDs) were synthesized through encapsulating CdTe QDs in various inorganic shells including CdS, ZnS and CdZnS. CdTe/CdS core/shell QDs exhibited a significant redshift of emission peaks (a maximum emission peak of 652 nm for the core/shell QDs and 575 nm for CdTe cores) with increasing shell thickness. In contrast, the redshift of photoluminescence (PL) peak wavelength of CdTe/ZnS QDs was less than 15 nm. The PL peak wavelengths of the core/shell QDs depended strongly on core size and shell thickness. The PL quantum yields (QYs) of the CdTe/CdS core/shell QDs are up to 67 % while that of CdTe/ZnS core/shell QDs is 45 %. A composite CdZnS shell made CdTe cores a high PL QY up to 51 % and broadly adjusted PL spectra (a maximum PL peak wavelength of 664 nm). The epitaxial growth of the shell was confirmed by X-ray powder diffraction analysis and luminescence decay experiments. Because of high PL QYs, tunable PL spectra, and low toxicity from a ZnS surface layer, CdTe/CdZnS core/shell QDs will be great potential for bioapplications.     

Easy preparation and characterization of highly fluorescent polymer composite microspheres from aqueous CdTe nanocrystals

Fluorescent microspheres were easily fabricated from aqueous CdTe nanocrystals (NCs). The NCs, which had negative charges on the surface, were first extracted to chloroform by cationic surfactant octadecyl-p-vinyl-benzyldimethylammonium chloride (OVDAC) and then swollen into performed polystyrene (PS) microspheres. Through this method, strong photoluminescence (PL) of aqueous NCs was inherited in the resultant composite microspheres. Moreover, the NCs were firmly stabilized in the microspheres, withstanding not only polar solvents but also nonpolar solvents. UV-vis spectrum, PL spectrum, TEM, and confocal fluorescence microscopy were used to characterize the product.     

Efficient Thermally Activated Delayed Fluorescence from All-Inorganic Cesium Zirconium Halide Perovskite Nanocrystals

Thermally activated delayed fluorescence (TADF) is generally observed in solid-state organic molecules or metal-organic complexes. However, TADF in all-inorganic colloidal nanocrystals (NCs) is rare. Herein, we report the first colloidal synthesis of an air-stable all-inorganic lead-free Cs₂ZrCl₆ perovskite NCs. The Cs₂ZrCl₆ NCs exhibit long-lived triplet excited state (138.2 μs), and feature high photoluminescence (PL) quantum efficiency (QY=60.37 %) due to TADF mechanism. The emission color can be easily tuned from blue to green by synthesizing the mixed-halide Cs₂ZrBr_xCl_6−x (0≤x≤1.5) NCs. Femtosecond transient absorption and temperature dependent PL measurements are performed to clarify the emission mechanism. In addition, Bi³⁺ ions are successfully doped into Cs₂ZrCl₆ NCs, which further extends the PL properties. This work not only develops a new lead-free halide perovskite NCs for potential optoelectronic applications, but also offers unique strategies for developing new inorganic phosphors.     

Temperature-dependent photoluminescence of highly luminescent water-soluble CdTe quantum dots

Highly luminescent water-soluble CdTe quantum dots(QDs) have been synthesized with an electrogenerated precursor.The obtained CdTe QDs can possess good crystallizability,high quantum yield(QY) and favorable stability.Furthermore,a detection system is designed firstly for the investigation of the temperature-dependent PL of the QDs.     

颜色可调的高荧光CdTe量子点的水相合成

以亚碲酸钠为碲源,硼氢化钠为还原剂,一步合成了巯基丁二酸(MSA)稳定的CdTe量子点.研究了反应液pH值、镉与碲的摩尔比及镉与巯基丁二酸的摩尔比等实验条件对CdTe量子点体系荧光量子产率的影响,并用荧光光谱、X射线粉末衍射及透射电子显微镜等对其进行了表征.结果表明,CdTe量子点具有闪锌矿结构,形貌呈球状;在pH=1...     

Excited Semiconductor Clusters: Magic Source

In this paper, we review the preparation and properties of CdS-like clusters as well as their important applications in several nanostructures. The clusters created by the reaction of S^2? ions generated by the decomposition of thioglycolic acid (TGA) and Cd²⁺ ions play important roles for the construction of novel nanocrystals (NCs), the assembly of the NCs, and the formation of nanostructures including 1D solid and tubal fibers, 2D dendritic morphology, and 3D crystals. The formation and property of the clusters depended strongly on the molar ratio of TGA and Cd²⁺ ions in solutions. When aqueous CdTe NCs coated with a hybrid SiO₂ shell containing the clusters, they revealed a drastic increase in photoluminescence (PL) efficiency (from 28 to 80 %) and temperature-dependent PL. These excellent PL properties were ascribed to the clusters very closed to CdTe cores. This is confirmed through the observation of a lengthening of the Auger recombination lifetime by a factor of ~3.5 in the presence of the clusters. The size of the clusters determined the PL properties of the hybrid SiO₂-coated NCs and those fibers. Because of their high PL, these biofunctional materials could provide a platform for various applications.     

Metal‐Enhanced Fluorescence of CdTe Nanocrystals in Aqueous Solution

Metal‐enhanced fluorescence of semiconductor nanocrystals (NCs) is investigated. There is very little attention paid to the metal‐enhanced fluorescence in aqueous solution, which has great potential applications in bioscience. In this work, we directly observe metal‐enhanced fluorescence of CdTe NC solution by simply mixing CdTe NCs and Au nanoparticles, both of which are negatively charged. In order to study this kind of photoluminescence enhancement in aqueous solutions, we propose a calibration method, which takes into account the light attenuation in solutions. After consideration of the light weakening in transmission, the maximal PL enhancement is about 3 times as large as the ones without Au NPs. Some factors related to the enhanced magnitude of fluorescence, for instance, the concentration and the molar feed ratio of CdTe NCs and Au NPs, are studied in detail. Furthermore, the decreased lifetimes of CdTe NCs induced by Au NPs are also obtained, which are in accord with the enhancement of the photoluminescence.     

Synthesis of CdTe Quantum Dots with Tunable Photoluminescence Using Tellurium Dioxide as Tellurium Source

A simple and convenient method has been developed for synthesis of water‐soluble CdTe quantum dots (QDs) under ambient atmospheric conditions. In contrast to the traditional aqueous synthesis, green to red emitting CdTe QDs were prepared by using TeO₂ to replace Te or Al₂Te₃ as tellurium source in this method. The influences of experimental variables, including pH value, 3‐mercaptopropionic acid (MPA)/Cd and Te/Cd molar ratios, on the emission peak and photoluminescence (PL) quantum yield (QY) of the obtained CdTe QDs have been systematically investigated. Experimental results indicate that green to red emitting CdTe QDs with a maximum photoluminescence quantum yield of 35.4% can be prepared at pH 11.3 and n_(Cd):n_(Te):n_(MPA)=1:0.1:1.7.     

Preparation of monodisperse CdTe nanocrystals-SiO2 microspheres without ligands exchange

Fluorescent CdTe-SiO₂ composite microspheres were prepared by a sol–gel method without the exchange of surface ligands for the first time. We loaded CdTe nanocrystals (NCs) into the matrix of silica microspheres during the formation of composite spheres. In contrast to CdTe NCs in aqueous solutions, CdTe NCs in the composite microspheres revealed better stability while their fluorescence properties were retained due to the confined effects of silica matrix. In addition, we also investigated the dependency of properties of these composite spheres on such important synthesis factors as pH value, concentration and stabilizers during experiment procedure in details.