The electrochemical oxidation of homocysteine at boron-doped diamond electrodes with application to HPLC amperometric detection

The electrochemical oxidation of homocysteine was studied at as-deposited and anodized (oxidized) boron-doped diamond (BDD) thin film electrodes with cyclic voltammetry, flow injection analysis and high-pressure liquid chromatography with amperometric detection. At anodized boron-doped diamond electrodes, highly reproducible, well-defined cyclic voltammograms for homocysteine oxidation were obtained in acidic media, while as-deposited diamond did not provide a detectable signal. In alkaline media, however, the oxidation response was obtained both at as-deposited and anodized diamond electrodes. The potential sweep rate dependence of homocysteine oxidation (peak currents for 1 mM homocysteine linearly proportional to v(1/2), within the range of 0.01 to 0.3 V s(-1)) indicates that the oxidation involves a diffusing species, with negligible adsorption on the BDD surface at this concentration. In the flow system, BDD exhibited a highly reproducible amperometric response, with a peak variation less than 2%. An extremely low detection limit (1 nM) was obtained at 1.6 V vs. Ag/AgCl. In addition, the determination of homocysteine in a standard mixture with aminothiols and disulfide compounds by means of isocratic reverse-phase HPLC with amperometric detection at diamond electrodes has been investigated. The results showed excellent separation, with a detection limit of 1 pmol and a linear range of three orders of magnitude.     

Electroanalysis of Gallic and Ellagic Acids at a Boron‐doped Diamond Electrode Coupled with High‐performance Liquid Chromatography

Electrochemistry of gallic acid (GA) and ellagic acid (EA) was investigated by cyclic voltammetry (CV) using a bare boron‐doped diamond (BDD) electrode. CVs indicate that the electro‐oxidation of both GA and EA are quasi‐reversible processes. High‐performance liquid chromatography (HPLC) coupled with a BDD electrode poised at+1.4 V offers the limit of detection (LOD, S/N=3) of 60 and 200 nM for GA and EA, respectively. The optimized method was then applied to the detection of both acids in Islay, Highland and Scotch whiskeys, with the highest concentrations found in a 14‐year‐old Highland whiskey.     

Fast determination of sugars in Coke and Diet Coke by miniaturized capillary electrophoresis with amperometric detection

The fast separation capability of a novel miniaturized capillary electrophoresis with amperometric detection (CE-AD) system was demonstrated by determining sugar contents in Coke and diet Coke with an estimated separation efficiency of 60,000 TP/m. Factors influencing the separation and detection processes were examined and optimized. The end-capillary 300 microm Cu wire amperometric detector offers favorable signal-to-noise characteristics at a relatively low potential (+0.50 V vs. Ag/AgCl) for detecting sugars. Three sugars (sucrose, glucose, and fructose) have been separated within 330 s in a 8.5 cm length capillary at a separation voltage of 1000 V using a 50 mM NaOH running buffer (pH 12.7). Highly linear response is obtained for the above compounds over the range of 5.0 to 2.0 x 10(2) microg/mL with low detection limit, down to 0.8 microg/mL for glucose (S/N = 3). The injection-to-injection repeatability for analytes in peak current (RSD < 3.6%) and for migration times (RSD < 1.4%) was excellent. The new miniaturized CE-AD system should find a wide range of analytical applications involving assays of carbohydrates as an alternative to conventional CE and micro-CE.     

Electrochemical detection of sugar-related compounds using boron-doped diamond electrodes

Electrochemical detection of sugar-related compounds was conducted using a boron-doped diamond (BDD) electrode as a detector for flow-injection analysis (FIA). Sugar-related compounds oxidize at high applied potentials, for which the BDD electrode is suitable for electrochemical measurements. Conditions for an FIA system with a BDD detector were optimized, and the following detection limits were achieved for sugar-related compounds: monosaccharides, 25-100 pmol; sugar alcohols, 10 pmol; and oligosaccharides, 10 pmol. The detection limit for monosaccharide D-glucose (Glu) was 105 pmol (S/N = 3). A linear range was acquired from the detection limit to 50 nmol, and the relative standard deviation was 0.65% (20 nmol, n = 6). A high-performance liquid chromatography (HPLC) column was added to the system between the sample injector and the detector and detection limits to the picomole level were achieved, which is the same for the HPLC system and the FIA system. The electrochemical oxidation reaction of Glu was examined using cyclic voltammetry with the BDD detector. The reaction proved to be irreversible, and proceeded according to the following two-step mechanism: (1) application of a high potential (2.00 V vs. Ag/AgCl) to the electrode causes water to electrolyze on the electrode surface with the simultaneous generation of a hydroxyl radical on the surface, and (2) the hydroxyl radical indirectly oxidizes Glu. Thus, Glu can be detected by an increase in the oxidation current caused by reactions with hydroxy radicals.     

Miniaturized capillary electrophoresis system with a carbon nanotube microelectrode for rapid separation and detection of thiols

Multi-walled carbon nanotube (CNT) was mixed with epoxy to fabricate microdisc electrode used as a detector for a specially designed miniaturized capillary electrophoresis (CE)-amperometric detection system for the separation and detection of several bioactive thiols. The end-channel CNT amperometric detector offers favourable signal-to-noise characteristics at a relatively low potential (0.8 V) for detecting thiol compounds. Factors influencing the separation and detection processes were examined and optimized. Four thiols (homocysteine, cysteine, glutathione, and N-acetylcysteine) have been separated within 130 s at a separation voltage of 2000 V using a 20 mM phosphate running buffer (pH 7.8). Highly linear response is obtained for homocysteine, cysteine, glutathione, and N-acetylcysteine over the range of 5-50 μM with detection limits of 0.75, 0.8, 2.9, and 3.3 μM, respectively. Good stability and reproducibility (R.S.D. < 5%) are obtained reflecting the minimal adsorption of thiols at the CNT electrode surface. The new microchip protocol should find a wide range of bioanalytical applications involving assays of thiol compounds.     

Cost-effective flow cell for the determination of malachite green and leucomalachite green at a boron-doped diamond thin-film electrode.

An electrooxidation and a cost-effective flow-based analysis of malachite green (MG) and leucomalachite green (LMG) were investigated at a boron-doped diamond thin-film (BDD) electrode. Cyclic voltammetry as a function of the pH of the supporting electrolyte solution was studied. Comparison experiments were performed with a glassy carbon electrode. A well-defined cyclic voltammogram, providing the highest peak current, was obtained when using phosphate buffer at pH 2. The potential sweep-rate dependence of MG and LMG oxidation (peak currents for 1 mM MG and LMG linearly proportional to v 1/2, within the range of 0.01 to 0.3 V/s) indicates that the oxidation current is a diffusion-controlled process on the BDD surface. In addition, hydrodynamic voltammetry and amperometric detection using the BDD electrode combined with a flow injection analysis system was also studied. A homemade flow cell was used, and the results were compared with a commercial flow cell. A detection potential of 0.85 V was selected when using a commercial flow cell, at which MG and LMG exhibited the highest signal-to-background ratios. For the homemade flow cell, a detection potential of 1.1 V was chosen because MG and LMG exhibited a steady response. The flow analysis results showed linear concentration ranges of 1-100 microM and 4-80 microM for MG and LMG, respectively. The detection limit for both compounds was 50 nM.     

Simultaneous detection of purine and pyrimidine at highly boron-doped diamond electrodes by using liquid chromatography

Highly boron-doped diamond (BDD) electrode, have been examined for simultaneous detection of purine and pyrimidine bases in mild acidic media by using HPLC with amperometric detection. Cyclic voltammetry at as-deposited (AD) and anodically oxidized (AO) BDD were used to study the electrochemistry and to optimize the condition for HPLC applications. At AO BDD electrode, due to its higher overpotential of oxygen evolution reaction, well-defined anodic peaks were observed for the oxidation of purine and pyrimidine bases in acid medium, whereas at AD BDD the oxidation peak of thymine was overlapped with the anodic current of oxygen evolution. The chromatograms of adenine, guanine, cytosine, thymine and 5-methylcytosine mixture were well resolved by using a silica-based column and a solution of 5% acetonitrile in 100 mM ammonium acetate buffer (pH 4.25) as the mobile phase. The detection was carried out at AO BDD electrode at an applied potential of 1.6 V versus Ag/AgCl. Linear calibration curves were obtained within the concentration range from 0.1 to 10 μM with the limits of detection (S/N = 3) ranging from 26.3 to 162.1 nM, resulting in an order of magnitude higher sensitivities than those at conventional electrodes. HPLC analysis with diamond amperometric detector was successfully applied for determination of 5-methylcytosine in real DNA samples with high reproducibility. No deactivation of the electrode was found during cyclic voltammetric and HPLC measurements, indicating the high stability for analysis of biological samples.     

Rapid Nanomolar Detection of Guaiacol from its Precursors Using a Core-shell Reversed-phase Column Coupled with a Boron-doped Diamond Electrode

The electrooxidation mechanisms of guaiacol (2-methoxyphenol), a food and beverage spoilage metabolite, and its precursors; vanillic acid (VA), vanillin, and ferulic acid (FA) were investigated by cyclic voltammetry (CV) with a boron-doped diamond (BDD) electrode. Reversed-phase liquid chromatography (RPLC) together with a BDD electrode poised at +1.6 V vs. Pd/H₂, was optimized for their sensitive detection. The separation was achieved in 60 s with a core-shell column (HALO C₁₈). The detection limits of these analytes ranged from 10–30 nM. The method was applicable for the analysis of guaiacol and its precursors from a popular commercial drink.     

Microchip capillary electrophoresis with electrochemical detector for fast measurements of aromatic amino acids

A method based on microchip capillary electrophoresis with amperometric detection was developed for the rapid separation and direct detection of oxidizable aromatic amino acids (without prior derivatization). The working electrode was a thick-film carbon strip electrode positioned opposite the outlet of the separation channel. Factors influencing the separation and detection processes were examined and optimized. The five aromatic amino acids, tyrosine, 5-hydroxytryptophan, tryptophan, p-aminobenzoic acid, and m-aminobenzoic acid, can be well separated within 5 min using a separation voltage of 2000 V and a 25 mM phosphate buffer (pH 7.0) run buffer containing 50 mM sodium dodecylsulfate. Most favorable amperometric detection was obtained at +0.95 V. Linear calibration plots are observed for micromolar concentrations of the oxidizable amino acids. The new protocol offers good stability and for reproducibility, with relative S.D. of less than 5% for both migration times and peak currents (n=8). It should be useful for the analysis of aromatic amino acids, as desired for life sciences.     

Development of ultra-high-performance supercritical fluid chromatography-mass spectrometry assays to analyze potential biomarkers in sweat

Liquid chromatography-mass spectrometry methods were required to afford the rapid separation and detection of purines and small organic acids. These compounds are found in sweat and sebum and are potential biomarkers for the early detection of pressures sores. Two ultra-high-performance supercritical fluid chromatography-mass spectrometry assays have been successfully developed for both classes of compounds. Separation for purines was achieved using a gradient of supercritical carbon dioxide and methanol with a 1-aminoanthracene sub 2 μm particle size column followed by positive ion electrospray ionization. Separation for organic acids was achieved using a gradient of supercritical carbon dioxide and methanol (50 mM ammonium acetate 2% water) with a Diol sub 2 μm particle size column followed by negative ion electrospray ionization. Calibration curves were created in the absence of internal standards and R² values > 0.96 were achieved using single ion monitoring methods for the protonated purines and the deprotonated acids. The two new assays afford rapid analytical methods for the separation and detection of potential biomarkers in human sweat leading to the early detection and prevention of pressure sores.     

Simple and Feasible Simultaneous Determination of Three Phenolic Pollutants on Boron‐Doped Diamond Film Electrode

A simple, rapid and feasible method is developed for direct and simultaneous determination of phenol (Ph), hydroquinone (HQ) and 4‐nitrophenol (4‐NP) on unmodified boron‐doped diamond (BDD) electrode. Results showed that the oxidative peaks of these three phenolic compounds can be completely separated on BDD electrode in acidic conditions by using electrochemical cyclic voltammetry technique. The peak potential separations are all higher than 0.35 V. Moreover, BDD electrode is extremely easy to be refreshed to obtain current values with good reproducibility, even if it is passivated by phenolic compounds with different adsorption characteristics. All the above features are on account of the outstanding electrochemical characteristics of BDD electrode, and lead to the advantage and feasibility for simultaneous determination of three phenolic compounds without any other separation operation. For each tested phenolic compound, the concentration range with linearity is in two or three orders of magnitude in the presence of other coexisting phenolic compounds with the concentrations more than 1000 times higher than that of the tested component. The present method is also shown to be promising for the determination of phenolic contaminants in the real wastewater samples.     

氯氮平、去甲氯氮平及奥氮平的高效液相色谱电化学检测特性的研究

 采用高效液相色谱安培电化学检测法 ,考察了氯氮平、去甲氯氮平和奥氮平在不同 pH值流动相下的色谱分离情况及其色谱峰高与检测电压的关系。结果表明 ,氯氮平、去甲氯氮平和奥氮平的保留时间均随流动相 pH值的升高而延长 ;在pH值为 4 5 6和 5 5 6的流动相中 ,均可实现基线分离。 3种化合物的色谱峰高与检测电压之间呈典型的“S”型曲线 ,pH值升高时该曲线均左移。氯氮平、去甲氯氮平和奥氮平的检测电压必须大于产生最大氧化电流的最低电压才能得到稳定的检测电流。这种典型的“S”型伏安曲线对于化合物的定量和定性检测具有重要意义。     

Dual electrode electrochemical detector for HPLC

Summary A method for determination of phenolic compounds in distilled alcoholic beverages has been developed. After separation by reversed phase chromatography these compounds are detected coulometrically in a dual electrode detector. The hydrodynamic electrochemical behaviour of the substances in oxidative and reductive mode was investigated. For quantitative determination phenolic compounds are oxidized at the first working electrode (+0.65 V); then the oxidation products are reduced at the second working electrode (0.0 V). The current due to these processes is recorded. By the high selectivity of the detection mode matrix interferences can be eliminated in several alcoholic beverages. In this way qualitative information is improved. The detection limits of phenolic acids and aldehydes are between 0.01 and 1 ng (S/N=3).

---

Dualelektroden-Detektor für die HPLCBestimmung von phenolischen Verbindungen in Spirituosen

     

Fluorimetric determination of dissociation constants and ph-controlled fluorescence analysis of purines and pyrimidines

Fluorimetrically determined pH-titration curves have been obtained for twelve purines and pyrimidines at room temperature, in aqueous solution. The pK(a) values for these compounds have been determined fluorimetrically and potentiometrically. Except for 6-mercaptopurine and uric acid, there is close agreement between the two sets of pK(a) values, but a large difference for the corresponding excited singlet-state values, pK(S1)(a), which were calculated previously. This indicates that the excited singlet-state proton-transfer rate is much slower than the fluorescence-decay rate of purines and pyrimidines in our experimental conditions. A direct, simple, pH-controlled fluorimetric method is proposed for the determination of purines and pyrimidines. The limits of detection vary between 60 ng ml and 5.4 mug ml .     

Nonaqueous capillary electrophoresis equipped with amperometric detection for analysis of chlorinated phenolic compounds

Nonaqueous capillary electrophoresis (NACE) equipped with amperometric detection has been developed for separation and detection of an 11-member model mixture of chlorinated phenolic compounds. With triacetyl-beta-cyclodextrin (TACD) as a novel selectivity selector, acetonitrile proved to be an excellent solvent for this water-insoluble cyclodextrin derivative. Resolution of the analytes was achieved by using an optimized acetonitrile medium consisting of 500 mM acetic acid, 10 mM sodium acetate, 12 mM TACD and 50 mM tetrabutylammonium perchlorate. Separation of analytes was attributed to differential electrostatic and/or inductive interactions of the analytes with the TACD/TBA+ complex and charged tetrabutylammonium phases. A simple end-column amperometric detector (Pt vs. Ag/AgCl, poised at +1.6 V) in conjunction with NACE was used to analyze chlorophenols. Amperometric detection of such target compounds in acetonitrile-based media offers high sensitivity and alleviates electrode fouling compared to aqueous buffers. The detection limits obtained, ranging from 30 nM to 500 nM, are 3-8-fold lower than those obtained with aqueous buffers.     

Separation of kaempferols in Impatients balsamina flowers by capillary electrophoresis with electrochemical detection

Capillary electrophoresis with wall-jet amperometric detection was used to detect kaempferol and its derivatives kaempferol-3-glucoside, kaempferol-3-glucosylrhamnoside and kaempferol-3-(p-coumaroyl)glucoside. The influence of buffer pH on separation was investigated and optimized. With a phosphate buffer at pH 7.5, nearly complete separation of the four kaempferols was achieved according to their different electrophoretic mobilities. The detection potential was also evaluated and optimized. At detection potential of +0.80 V vs. saturated calomel electrode, an amperometric response with high sensitivity and stability was obtained for these four compounds. Detection limit estimated for all the kaempferols examined was less than 1.4 fmol, based on S/N=3. The use of this method for the separation and detection of these compounds present in balsam flowers (Impatiens balsamina) is reported.     

Electrochemical Detection of Clenbuterol in Pig Liver at Pyrrole-DNA Modified Boron-doped Diamond Electrode

Introduction Clenbuterol { 4-amino-[( tert-butylamino) meth-yl]-3,5-dichlorobenzyl alcohol hydrochloride} is aβ-agonist drug[1]. It can improve the ratio of muscle tofat when it is administrated with high doses to ani-mals[2,3]. However, the residues of clenbuterol(CL)are toxic to humans, leading to sickness and possibleheart complication[4]. It has been reported that CL iseasy to accumulate in animal livers.Recently, some analytical methods for the detec-tion of CL, such as HPLC[5], GC…     

Electrochemical analysis of d-penicillamine using a boron-doped diamond thin film electrode applied to flow injection system

The electroanalysis of d-penicillamine in 0.1 phosphate buffer (pH 7) was studied at a boron-doped diamond thin film (BDD) electrode using cyclic voltammetry as a function of concentration of analyte and pH of analyte solution. Comparison experiments were performing using a glassy carbon (GC) electrode. The BDD electrode exhibited a well-resolved and irreversible oxidation voltammogram, but the GC electrode provided only an ill-defined response. The BDD electrode provided a linear dynamic range from 0.5 to 10 mM and a detection limit of 25 muM (S/B>/=3) in voltammetric measurement. It was also found that the peak potentials were decreased when the pH of the analyte solution was increased. In addition, penicillamine has been studied by hydrodynamic voltammetry and flow injection analysis with amperometric detection using the BDD electrode. The flow injection analysis results at the diamond electrode indicated a linear dynamic range from 0.5 to 50 muM and a detection limit of 10 nM (S/N approximately 4). The proposed method was applied to determine d-penicillamine in dosage form (capsules), the results obtained in the recovery study (255+/-2.50 mg per tablet) were comparable to those labeled (250 mg per tablet).     

Microchip capillary electrophoresis with amperometric detection for rapid separation and detection of phenolic acids

A microchip capillary-electrophoresis protocol for rapid and effective measurements of food-related phenolic acids (including chlorogenic, gentisic, ferulic, and vanillic acids) is described. Relevant parameters of the chip separation and amperometric detection are examined and optimized. Under optimum conditions, the analytes could be separated and detected in a 15 mM borate buffer (pH 9.5, with 10% of methanol) within 300 s using a separation voltage of 2000 V and a detection voltage of +1.0 V. Linear calibration plots are observed for micromolar concentrations of the phenolic acid compounds. The negligible sample volumes used in the microchip procedure obviates surface fouling common to amperometric measurements of phenolic compounds. The new microchip protocol offers great promise for a wide range of food applications requiring fast measurements and negligible sample consumption. An application on a commercial red wine was performed with minimal sample preparation and promising results.     

Electrochemical analysis of -penicillamine using a boron-doped diamond thin film electrode applied to flow injection system

The electroanalysis of -penicillamine in 0.1 phosphate buffer (pH 7) was studied at a boron-doped diamond thin film (BDD) electrode using cyclic voltammetry as a function of concentration of analyte and pH of analyte solution. Comparison experiments were performing using a glassy carbon (GC) electrode. The BDD electrode exhibited a well-resolved and irreversible oxidation voltammogram, but the GC electrode provided only an ill-defined response. The BDD electrode provided a linear dynamic range from 0.5 to 10 mM and a detection limit of 25 μM (S/B≥3) in voltammetric measurement. It was also found that the peak potentials were decreased when the pH of the analyte solution was increased. In addition, penicillamine has been studied by hydrodynamic voltammetry and flow injection analysis with amperometric detection using the BDD electrode. The flow injection analysis results at the diamond electrode indicated a linear dynamic range from 0.5 to 50 μM and a detection limit of 10 nM (S/N≈4). The proposed method was applied to determine -penicillamine in dosage form (capsules), the results obtained in the recovery study (255±2.50 mg per tablet) were comparable to those labeled (250 mg per tablet).