Mid-infrared ZGP OPO pumped by near-degenerate narrowband type-I PPKTP parametric oscillator

The total pulse energy of the signal and idler in a near-degenerate type-I periodically poled KTiOPO₄ (PPKTP) optical parametrical oscillator (OPO) was spectrally confined within a 2 nm spectral bandwidth at 2.13 μm. This was achieved by using a volume Bragg grating as the output coupler. Both the signal and the idler from the PPKTP OPO were then simultaneously used to pump a mid-infrared ZnGeP₂ (ZGP) OPO. The 2 nm bandwidth was narrower than the ZGP crystal acceptance bandwidth and, thus, made efficient conversion in the second OPO possible. A total slope efficiency of 10% from 1.06 μm to the 3.5–5 μm region was demonstrated, generating 250 μJ in the mid-IR with only 3.6 mJ of 1.06 μm pump energy. This corresponds to a Nd:YAG pump to mid-IR conversion efficiency of 7%. PACS 42.65.Yj; 42.72.Ai; 42.40.Eq     

8.30 μm singly resonant ZnGeP2 optical parametric oscillators pumped by a Tm,Ho:GdVO4 laser

A single resonator 8.30 μm ZnGeP₂ (ZGP) optical parametric oscillators (OPO) was reported in the paper. The OPO was pumped by a 10.2-W Tm,Ho:GdVO₄ laser at 8 kHz in a Q-switch mode, a 170-mW idler was obtained at 8.30 μm, and the output power of the idler and signal wave was 1.0 W, corresponding to an optical-optical conversion efficiency of 10.3% and a slope efficiency of 20.9%. Tm,Ho:GdVO₄ laser was pumped by a 30-W fiber-coupled laser diode (LD) at the center wavelength of 801 nm. The output wavelength of Tm,Ho:GdVO₄ laser was at 2.05 μm, and the energy per pulse of 1.28 mJ in 18 ns was achieved at 8 kHz with the peak power of 71.1 kW.     

High-efficiency,high-repetition-rate,temperature-tuning optical parametric oscillator based on periodically poled MgO-doped lithium niobate

We report a compact and viable source of high-efficiency, high-repetition-rate, temperature-tuning, mid-IR optical parametric oscillator (OPO) based on periodically poled MgO-doped lithium niobate (PPMgOLN) pumped by a homemade high power AOM Q-switched Nd:YVO₄ laser centered at 1.064 μm. With an optimal plane-concave resonator configuration, average output power of 5.7 W at 2.73 μm was obtained when the pump power was 25 W at the repetition rate of 80 kHz. The conversion efficiency from the 1.064 μm laser to the 2.73 μm laser was 22.8%. Temperature tuning of the OPO yielded a signal wavelength range from 1.67 to 1.75 μm and an idler wavelength in the range of 2.72 to 2.92 μm.     

All-solid-state cw mode-locked picosecond KTiOAsO4 (KTA) optical parametric oscillator

4 (KTA) optical parametric oscillator (OPO) synchronously pumped by a cw diode-pumped mode-locked Nd:YVO₄ oscillator–amplifier system. The laser system (pumped by 84 W of cw 808-nm diode radiation) generates 7-ps-long pulses at 1.064 μm with a repetition rate of 83.4 MHz and an average power of 29 W. The OPO, synchronously pumped by the 1.064-μm laser pulses, consists of a 15-mm-long KTA crystal (cut for type II noncritical phase-matching) in a folded signal resonant linear resonator. The average powers of the 1.54-μm signal radiation and the 3.47-μm idler radiation are 14.6 W and 6.4 W, respectively. The total OPO output of 21 W corresponds to an internal efficiency of 75%. The experimental investigations include measurements of the OPO output power (and its dependence on the pump power, the transmission of the output coupler, and the resonator length) and of the pulse properties (such as pulse duration and spectral width). The measured results are in good agreement with the predictions of a numerical analysis based on a split-step Fourier method. Received: 4 May 1998     

High-efficiency mid-infrared laser from synchronous optical parametric oscillation and amplification based on a single MgO:PPLN crystal

This paper presents a specially designed optical parametric oscillator (OPO) which achieved high-efficiency mid-infrared laser of 2.83 μm. The cascaded nonlinear interactions of OPO and optical parametric amplifier (OPA) were simultaneously realized in a single MgO:PPLN crystal. The signal oscillation of 1.70 μm was used to pump a secondary parametric process that resulted in amplification of the idler laser of 2.83 μm. When the MgO:PPLN crystal with a grating period of 31.2 μm was pumped by a 1.064 μm laser and operated at 148°C, the quasi-phase-matching of both OPO and OPA could be simultaneously achieved. Average output power of 7.68 W at 2.83 μm was obtained for 25 W of pump at 7 kHz. The power conversion efficiency of 2.83 μm laser was 30.7%, which was evidently higher than common OPOs.     

Effect of resonator length on ZnGeP<Subscript>2</Subscript> doubly resonant optical parametric oscillator pumped by a Tm,Ho:GdVO<Subscript>4</Subscript> laser

The effect of resonator length on ZnGeP₂ doubly resonant optical parametric oscillator was reported in this letter. With the employment of a Tm,Ho:GdVO₄ laser as the pump source at 2.05 μm, we have found that there are obvious peaks of the output power when the resonator lengths are matched to the length of the pump source. The ZGP OPO can generate a maximum output power of 4.27 W at 3.80 μm signal and 4.45 μm idler when the resonator length matches that of the pump source.     

Optical parametric oscillators for high pulse energy and high average power operation based on large aperture periodically poled KTP and RTA

We report on optical parametric oscillators (OPOs) based on large aperture periodically poled KTiOPO₄ (PPKTP) and RbTiOAsO₄ (PPRTA) pumped with high pulse energy and high average power Q-switched solid-state lasers. The OPOs were pumped with 1064-nm pulses of a diode-pumped Nd:YVO₄ laser at 20 kHz repetition rate. The emitted signal wavelengths were 1.72 μm and 1.58 μm and the idler wavelengths were 2.79 μm and 3.26 μm, respectively. Pumping the PPKTP OPO with 7.2 W and the PPRTA OPO with 8 W average power, 2 W and 1.3 W total OPO output powers were generated. Two-dimensional measurements of the total OPO output power, the signal wavelength and the signal bandwidth in dependence on the crystal location indicated a good uniformity of the quasiphasematching structure over the entire 3-mm-thick crystals. This allowed pumping with larger pump beams and therefore with pulse energies of tens of millijoules. Pumping with different flash-lamp-pumped lasers, good OPO performance and high output pulse energies could be achieved for all pump lasers. Maximum input pulse energies of 56 mJ gave output pulse energies of as much as 18 mJ. The temperature tuning behaviors of both OPOs were measured, showing excellent agreement with calculated temperature tuning curves. New equations for temperature dispersion in RTA are presented. These results show that large-aperture PPKTP and PPRTA crystals are well suited for tunable nanosecond OPO operation with multi-watt average pump power and several tens of millijoules pump pulse energies. Received: 7 September 2001 / Published online: 7 November 2001     

High-power picosecond LiB3O5 optical parametric oscillators tunable in the blue spectral range

The paper reports on an experimental investigation and numerical analysis of noncritically and critically phasematched LiB₃O₅ (LBO) optical parametric oscillators (OPOs) synchronously pumped by the third harmonic of a cw diode-pumped mode-locked Nd:YVO₄ oscillator–amplifier system. The laser system generates 9.0 W of 355-nm mode-locked radiation with a pulse duration of 7.5 ps and a repetition rate of 84 MHz. The LBO OPO, synchronously pumped by the 355-nm pulses, generates a signal wave tunable in the blue spectral range 457–479 nm. With a power of up to 5.0 W at 462 nm and 1.7 W at 1535 nm the conversion efficiency is 74%. The OPO is characterized experimentally by measuring the output power (and its dependence on the pump power, the transmission of the output coupler and the resonator length) and the pulse properties (such as pulse duration and spectral width). Also the beam quality of the resonant and nonresonant waves is investigated. The measured results are compared with the predictions of a numerical analysis for Gaussian laser and OPO beams. In addition to the blue-signal output visible-red 629-nm radiation is generated by sum-frequency mixing of the 1.535-μm infrared idler wave with the residual 1.064-μm laser radiation. A power of 1.25 W of 1.535-μm idler radiation and 5.7 W of 1.064-μm laser light generated a red 629-nm output power of 2.25 W. Received: 2 February 2000 / Revised version: 28 July 2000 / Published online: 22 November 2000     

High-power mid-infrared tunable optical parametric oscillator based on 3-mm-thick PPMgCLN

The experimental results of a high-power tunable mid-IR laser are presented. The optical parametric oscillator (OPO) with a 3-mm-thick PPMgCLN crystal was pumped by a 1.064 μm pulse laser. When the pump power of the 1.064 μm laser was 151 W at 10 kHz, and the operating temperature of the PPMgCLN with 5% MgO doping was 100°C, average output power of 23.7 W at 3.91 μm was obtained with a slope efficiency of 18.2% for the idler resonant OPO. The variation of the 3.91 μm output power was about ±4% in 10 min continuous operation. The beam quality factor M ² was less than 2.6. The average output power of 27.4 W at 3.91 μm was also obtained with 151 W pump power and the slope efficiency of 20.9% for the signal resonant OPO by changing the coating parameters of the OPO cavity mirrors. The mid-IR wavelength tunability of 3.7–4.0 μm can be achieved by adjusting the temperature of a 29 μm period PPMgCLN crystal from 200 to 30°C.     

High-power,high-quality ZGP OPO pumped by a Tm,Ho:GdVO<Subscript>4</Subscript> laser

We report a ZGP OPO system capable of producing >6 W at a signal wavelength of 3.80 μm and an idler wavelength of 4.45 μm. The pumping source is the Tm,Ho:GdVO₄ laser operated at 2.049 μm with an M ² of 1.07. The ZGP OPO generated a total combined output power of 6.1 W at signal wavelength and idler wavelength under pumping power of 18.3 W, and an M ² of 1.7 for OPO output was obtained.     

Efficient sub-nanosecond intracavity optical parametric oscillator pumped with a passively Q-switched Nd:GdVO<Subscript>4</Subscript> laser

An efficient diode-pumped passively Q-switched Nd:GdVO₄/Cr⁴⁺:YAG laser was employed to generate a high-repetition-rate, high-peak-power eye-safe laser beam with an intracavity optical parametric oscillator (OPO) based on a KTP crystal. The conversion efficiency for the average power is 8.3% from pump diode input to OPO signal output and the slope efficiency is up to 10%. At an incident pump power of 14.5 W, the compact intracavity OPO cavity, operating at 46 kHz, produces average powers at 1571 nm up to 1.2 W with a pulse width as short as 700 ps. PACS 42.60.Gd; 42.65.Yj; 42.55.X     

All fiber MOPA laser-pumped,continuous-wave,mid-infrared,singly-resonant optical parametric oscillator based on periodically poled MgO-Doped LiNbO<Subscript>3</Subscript>

We report a continuous-wave (CW) mid-infrared singly resonant optical parametric oscillator (SRO) based on periodically poled MgO-doped LiNbO₃ (PPMgLN) pumped by a high power, single frequency fiber laser in master oscillator-power amplifier (MOPA) configuration at 1.064 μm. Using four-mirror ring OPO cavities, at the PPMgLN’s grating period of 30.5 μm and the temperature of 23°C, we achieved the maximum idler output power of 7.2 W at 3.4 μm when the pump power was 52.8 W. The total power-conversion efficiency from the pump to the idler in this experiment is about 13.6%, and corresponds to ∼44% of quantum-limited performance.     

High-Power,high-repetition-rate operation of a period-continuously-tunable optical parametric oscillator at 3.78–4.62 μm based on a fan-out periodically poled MgO-doped lithium niobate

We present a period-continuously-tunable optical parametric oscillator based on a fan-out MgO:PPLN with a grating period range from 26.9 to 29.5 μm. The OPO was pumped by a Q-switched Nd:YAG laser with a repetition of 10 kHz. With a grating period of 29.3 μm and 22.0 W pump power, the idler output power at 3.78 μm arrived at 3.40 W. With a period of 27.1 μm and 13.5 W pump, the idler output at 4.58 μm arrived at 0.36 W. This is, to our best knowledge, the highest average power for pulsed OPO operating near 4.5 μm based on PPLN or MgO:PPLN. By translating the fan-out MgO:PPLN, the idler wavelength was tuned continuously from 3.78 to 4.62 μm.     

Diode-pumped passively Q-Switched intracavity OPO with a folded cavity configuration

We present in this report an efficient KTP-based intracavity optical parametric oscillator driven by a diode-pumped Nd:GdVO₄/Cr:YAG passively Q-switched laser. For the first time, a novel folded cavity configuration was employed to set the KTP and Cr:YAG crystals separately at different fundamental beam waists. Based on the ABCD-matrix theory and by taking the thermal lens effect into account, the laser cavity was well optimized to enhance the OPO performance. A diode pump threshold as low as 1.2 W and a maximum signal (1.57 μm) average output power up to 560 mW have been achieved. Efficient energy transfer in the IOPO leads to short pulse duration (1.8–2.6 ns) and high peak power (6.8 kW) output at 1.57 μm. Additionally, the correlation dynamics between the pump laser and the OPO was analyzed in detail.     

High-repetition-rate eye-safe intracavity KTA OPO driven by a diode-end-pumped Q-switched Nd:YVO4 laser

An eye-safe, high-repetition-rate, single-resonant nanosecond intracavity optical parametric oscillator (IOPO), based on a non-critically phase-matched KTA crystal driven by a diode-end-pumped acousto-optically Q-switchedNd:YVO4 laser, was demonstrated for the first time to our knowledge. With an absorbed pump power of 11.3 W, 1.1 W average power and 2.5 ns pulse width at the signal (1534 nm) wavelength for 30-kHz repetition rate are synchronously achieved with the 25 mm long KTA crystal. The corresponding peak power and single pulse energy are estimated to be up to 14.7 kW and 36.7 μJ. The conversion efficiency from diode laser power to OPO signal output power was 9.8% and the corresponding slope efficiency was 15.4%. PACS 42.60.Gd; 42.65.Yj; 42.55.Xi     

Continuous wave,singly resonant MgO:PPLN OPO pumped by a Nd:YVO<Subscript>4</Subscript>/YVO<Subscript>4</Subscript> ring laser

A continuous wave (CW), extra-cavity singly resonant optical parametric oscillator (SRO) has been demonstrated. The SRO is based on 5% magnesium-oxide doped periodically-poled lithium niobate (MgO:PPLN) pumped by a CW Nd:YVO₄/YVO₄ ring laser centered at 1064.4 nm. The nonlinear crystal temperature is kept at 120.0 ± 0.1°C and a domain period of 30 μm is used in this experiment. When the pump power is 11 W, an output power of 2.0 W at the idler wavelength of 3.479 μm has been obtained from the OPO. The optical-optical conversion efficiency is about 18.2%, and the slope efficiency is about 20.8%.     

Synchronously pumped femtosecond optical parametric oscillator of congruent and stoichiometric MgO-doped periodically poled lithium niobate

A synchronously pumped femtosecond optical parametric oscillator based on congruent MgO-doped periodically poled lithium niobate (c-MgO:PPLN) is reported. The system, operating at room temperature, was pumped by a mode-locked Ti:sapphire laser. The wavelengths of the signal and idler waves were tuned from 870 nm to 1.54 μm and 1.58 to 5.67 μm, respectively, by changing the pump wavelength, the grating period or the cavity length. Pumped by 1.1 W of 755 nm laser radiation, the OPO generated 310 mW of 1080 nm radiation. This signal output corresponds to a total conversion efficiency of 50%. Without dispersion compensation the OPO generated phase-modulated signal pulses of 200 fs duration. Besides the OPO of c-MgO:PPLN, an OPO of stoichiometric (s) MgO:PPLN was investigated. Because of the reduced sensitivity to photorefractive damage, both crystals allowed efficient OPO operation at room temperature. Received: 19 August 2002 / Revised version: 11 December 2002 / Published online: 19 March 2003 RID="*" ID="*"Corresponding author. Fax: +49-631/205-3906, E-mail: andres@physik.uni-kl.de     

Amplification assisted optical parametric oscillator in the mid-infrared region

We demonstrate a high efficiency mid-infrared laser source based on optical parametric oscillator (OPO) assisted by an intracavity optical parametric amplification (OPA). The OPA-assisted-OPO scheme was realized in one piece of commensurable dual-periodic superlattice in which the signal light generated from the OPO process serves as the pump light for the OPA process. A maximum output power of 508 mW at 3.92 μm was achieved under a pump power of 2.85 W at 1.064 μm. The pump-to-idler conversion efficiency is 17.8% and the slope efficiency is 23.8%, and the enhancements of them are 58.9% and 67.6%, respectively, comparing with the standard OPO scheme.     

High efficiency KTiOAsO4 optical parametric oscillator within a diode-side-pumped two-rod Nd:YAG laser

A high efficiency KTiOAsO₄(KTA) intracavity optical parametric oscillator (IOPO) is demonstrated within a diode-side-pumped acousto-optically (AO) Q-switched two-rod Nd:YAG laser. With a 25-mm-long X-cut KTA crystal, efficient parametric conversions to signal (1.54 μm) and idler (3.47 μm) waves are realized. The highest output power of 15.8 W including 12.7 W signal and 3.1 W idler power is obtained at a repetition rate of 7.5 kHz and a pump power of 208 W, corresponding to an optical-to-optical conversion efficiency of up to 7.6%. The signal pulse duration is 32 ns with a peak power of 53 kW. At a repetition rate of 12.5 kHz and the pump power of 208 W, the highest idler power of 3.4 W is obtained with a peak power of 14 kW and a pulse duration of 19 ns. And the beam quality factors (M ²) of the signal and idler waves are determined to be around 2 and 20, respectively.     

High repetition rate mid-infrared generation with singly resonant optical parametric oscillator using multi-grating periodically poled MgO:LiNbO3

A high repetition rate mid-infrared singly resonant optical parametric oscillator (OPO) using MgO-doped multi-grating periodically poled LiNbO₃ (MgO:PPLN) is demonstrated. A 1064 nm Q-switched Nd:YVO₄ laser at 10 kHz repetition rate and pulse width of 17.8 ns was used to pump the OPO. The period of the quasi-phase matched (QPM) grating in the multi-grating MgO:PPLN chip varied from 25.5 to 31.5 μm in steps of 0.5 μm. This corresponds to the generation of a signal beam from 1.37 to 1.64 μm and an idler beam from 3.0 to 4.8 μm, respectively. A maximum signal power of 250 mW and idler power of 140 mW has been obtained with an input pump beam of power 1.92 W, for a grating period of 30.5 μm. A maximum optic-optic conversion efficiency of 20% and 7.4% in the idler has been observed. It has been observed that the output power increases as the period of the grating increases.