Synthesis and photovoltaic properties of a furan-diketopyrrolopyrrole-fluorene terpolymer

We report the synthesis of two solution-processable reduced band gap donor–acceptor conjugated polymers p(C8-DPP-F) and p(C12-DPP-F), composed from 9,9-dioctylfluorene as the donor moiety, diketopyrrolopyrrole (DPP) moiety as the acceptor moiety and furan bridges. Two different alkyl chains, n-dodecyl and n-octyl were used on the DPP moiety and the impact of this structural modification evaluated in detail. Both polymers exhibited similar optical and electrochemical properties with optical band gap of around 1.75 eV as result of LUMO levels near −3.4 eV and high-lying HOMO levels of ∼5.2 eV. Bulk heterojunction photovoltaic devices using these polymers electron donors along with PC₇₀BM as the electron acceptor, gave power conversion efficiency of 1.60% and 0.75% for p(C12-DPP-F) and p(C8-DPP-F) respectively.     

Structure and morphology of nanostructured zinc oxide thin films Prepared by dip-vs. spin-coating methods

In this study, we use dipping and spinning methods to coat glass slides with sol-gel ZnO thin films, composed of zinc acetate dihydrate, monoethanolamine (MEA), de-ionized water and isopropanol. The effect of the annealing temperature on the structural morphology and optical properties of these films is investigated. These ZnO films were preheated at 275 °C for 10 min and annealed either at 350, 450 or 550 °C for 60 min. As-deposited films, formed by amorphous zinc oxide-acetate submicron particles, are transformed into a highly-oriented ZnO after thermal treatment. The surface morphology, phase structure and optical properties of the thin films were investigated by scanning electron microscopy, X-ray diffraction (XRD) and optical transmittance. Both techniques produced nanostructured ZnO thin films with well-defined orientation. The annealed films were transparent in the visible range with an absorption edge at about 375 nm and a transmittance of ca 85–90% with an average diameter of 40 nm. XRD results show the film was composed of polycrystalline wurtzite, with a preferential c-axis orientation of (002) and a single sharp XRD peak at 34.40, corresponding to the hexagonal ZnO. The grain size is increased by the annealing temperature. Both coating techniques create sol-gel ZnO films with the potential for application as transparent electrodes in optic and electronic devices.     

Optimizing polymer aggregation and blend morphology for boosting the photovoltaic performance of polymer solar cells via a random terpolymerization strategy

Compared to regular conjugated polymers,the random conjugated terpolymers are usually not beneficial to achieve highly efficient non-fullerene (NF)-based polyme...     

Effects of subtle change in side chains on the photovoltaic performance of small molecular donors for solar cells

Small-molecule organic solar cells (SMOSCs) have attracted considerable attention owing to the merits of small molecules, such as easy purification, well-defined chemical structure. To achieve high-performance SMOSCs, the rational design of well-matched donor and acceptor materials is extremely essential. In this work, two new small molecular donor materials with subtle change in the conjugated side thiophene rings are synthesized. The subtle change significantly affects the photovoltaic performance of molecular donors. Compared with chlorinated molecule MDJ-Cl, the non-chlorinated analogue MDJ exhibits decreased miscibility with the non-fullerene acceptor Y6, can more efficiently quench the excitons of Y6. As a result, a improved PCE of 11.16% is obtained for MDJ:Y6 based SMOSCs. The results highlight the importance of fine-tuning the molecular structure to achieve high-performance SMOSCs.     

Effect of coadsorbent properties on the photovoltaic performance of dye-sensitized solar cells

Stearic acid as a coadsorbent, which has a low dipole moment and high solubility, retarded the rate of dye adsorption during the competitive anchoring process on the TiO(2) layer in dye-sensitized solar cells (DSCs), thereby increasing the content of strongly bound dye on the TiO(2) surface. This resulted in an approximately 25% improvement in both J(SC) and the power conversion efficiency of the DSCs, even for much lower dye coverage.     

Effects of different formulation PEDOT:PSS hole transport layers on photovoltaic performance of organic solar cells

In this study, the effects of the various types of PEDOT:PSS with different conductivities on the photovoltaic parameters of organic solar cells were investigated. The performances of five various commercially available PEDOT:PSS with formulations such as FET, PT2, PH1000, PH500 and PH were compared. It was observed that the device employing PH1000 as an interlayer between ITO and the active layer exhibited the highest photovoltaic performance as compared to other devices with FET, PT2, PH500 and PH. Copyright © 2015 John Wiley & Sons, Ltd.     

Effect of coadsorbent on the photovoltaic performance of zinc pthalocyanine-sensitized solar cells

The effect of chenodeoxycholic acid as a coadsorbent on TiO 2 nanocrystalline solar cells incorporating phthalocyanine sensitizers was studied under various conditions. Adding chenodeoxycholic acid onto TiO 2 nanoparticles not only reduces the adsorption of phthalocyanine sensitizers but also prevents sensitizer aggregation, leading to different photovoltaic performance. The inspection of IPCE and absorption spectra showed that the load of phthalocyanine sensitizers is strongly dependent on the molar concentration of chenodeoxycholic acid coadsorbent. The open circuit voltage of the solar cells with chenodeoxycholic acid coadsorbent increases due to the enhanced electron lifetime in TiO 2 nanoparticles coupled with the band edge shift of TiO 2 to negative potentials.     

Influence of blend microstructure on bulk heterojunction organic photovoltaic performance

The performance of organic photovoltaic devices based upon bulk heterojunction blends of donor and acceptor materials has been shown to be highly dependent on the thin film microstructure. In this tutorial review, we discuss the factors responsible for influencing blend microstructure and how these affect device performance. In particular we discuss how various molecular design approaches can affect the thin film morphology of both the donor and acceptor components, as well as their blend microstructure. We further examine the influence of polymer molecular weight and blend composition upon device performance, and discuss how a variety of processing techniques can be used to control the blend microstructure, leading to improvements in solar cell efficiencies.     

Effects of chemical structure and composition of the polymer matrix on the morphology and electro-optical performance of polymer-dispersed liquid crystal films

Polymer-dispersed liquid crystal (PDLC) systems on the basis of nematic liquid crystal E7 and amphiphilic binary copolymers of acrylic acid (AA) with such acrylates as 2-ethylhexyl acrylate (EHA), n-butyl acrylate (BA), and methyl acrylate (MA) are investigated. It is shown that the liquid crystal (LC) drops in the copolymer EHA–AA have submicrometre sizes, and their dependence on the composition of the photo-curable monomer mixture is described by a parabolic curve. The highly oriented domain structure in the same system is first revealed when electric field is applied. The threshold voltage for all systems begins to increase with some critical composition of a monomer mixture in which the longer the hydrocarbonic radical in an acrylate molecule, the higher the content of AA. The PDLC system based on the BA–AA copolymer with 30 wt% LC exhibits the least value of the driving voltage, 1 V μm^–1, and the lowest memory effect.     

基于不同取代基的噻吩-三苯胺染料敏化剂的合成与光伏性能

本文合成了含3种不同取代基的噻吩-三苯胺染料敏化剂(H1,H2和H3),并将其应用于二氧化钛纳米晶染料敏化太阳能电池.系统地研究了3种染料的光物理、电化学和光伏性能.基于H1的染料敏化太阳能电池获得了9.10%的光电转换效率(Voc=0.72V,Jsc=18.03mAcm-2,FF=0.70).     

衣康酸-天冬氨酸-苯乙烯磺酸钠三元共聚物合成及阻垢性能研究

以衣康酸(IA)、天冬氨酸(ASP)及苯乙烯磺酸钠(SSS)为单体,过硫酸铵为引发剂,采用水溶液自由基聚合法合成了IA-ASP-SSS三元共聚物,并对产物结构进行红外表征。探讨单体配比、引发剂用量、聚合温度、反应时间对共聚物阻垢性能的影响,通过正交实验和单因素实验确定最佳合成条件。采用静态阻垢法考察阻垢剂用量、钙离子浓度对阻垢性能的影响。结果表明：共聚单体的物质的量比(nASP:nIA:nSSS)为1:1:0.1、引发剂用量为单体总质量的9%、反应温度85℃且反应时间3h时,合成的IA-ASP-SSS共聚物对碳酸钙、磷酸钙及硫酸钙的阻垢率皆在95%以上,且此共聚物阻垢剂适用于高硬度水环境。     

Influence of single-walled carbon nanotubes induced crystallinity enhancement and morphology change on polymer photovoltaic devices

Single-walled carbon nanotubes (SWNTs) were determined to have significant interaction with poly(3-hexylthiophene) (P3HT), which is helpful to form continuous active film with interpenetrating structure and improve the crystallinity of the resultant film for SWNTs/P3HT composite. Photovoltaic devices based on an active film with relatively higher crystallinity display much enhanced performance. The work function of carbon nanotubes modulated by electron transferring from P3HT to SWNTs is proposed to explain the high open-circuit voltage (V(OC)) obtained from the photovoltaic devices based on the SWNTs/P3HT system.     

Effect of hole-transporting materials on the photovoltaic performance and stability of all-ambient-processed perovskite solar cells

High-efficiency perovskite solar cells(PSCs) reported hitherto have been mostly prepared in a moisture and oxygen-free glove-box atmosphere, which hampers upscaling and real-time performance assessment of this exciting photovoltaic technology. In this work, we have systematically studied the feasibility of allambient-processing of PSCs and evaluated their photovoltaic performance. It has been shown that phasepure crystalline tetragonal MAPbI_3 perovskite films are instantly formed in ambient air at room temperature by a two-step spin coating process, undermining the need for dry atmosphere and post-annealing.All-ambient-processed PSCs with a configuration of FTO/TiO_2/MAPbI_3/Spiro-OMeTAD/Au achieve opencircuit voltage(990 mV) and short-circuit current density(20.31 mA/cm~2) comparable to those of best reported glove-box processed devices. Nevertheless, device power conversion efficiency is still constrained at 5% by the unusually low fill-factor of 0.25. Dark current–voltage characteristics reveal poor conductivity of hole-transporting layer caused by lack of oxidized spiro-OMe TAD species, resulting in high seriesresistance and decreased fill-factor. The study also establishes that the above limitations can be readily overcome by employing an inorganic p-type semiconductor, copper thiocyanate, as ambient-processable hole-transporting layer to yield a fill-factor of 0.54 and a power conversion efficiency of 7.19%. The present findings can have important implications in industrially viable fabrication of large-area PSCs.     

Control of morphology in efficient photovoltaic diodes from discotic liquid crystals

We report on the role of morphology in photovoltaic diodes with blend active layers composed of perylene tetracarboxdiimide (EPPTC) and hexabenzocoronene (HBC) derivatives as electron and hole acceptors. Controlled annealing of HBC:EPPTC films while in conformal contact with a flat elastomeric stamp improves photovoltaic response, leading to an external quantum efficiency of 29.5% at 460 nm and an open-circuit voltage of 0.70 V. The improved performance is attributed in part to larger crystalline domains following annealing. The elastomeric stamp restricts the top surface of the thin film during annealing, leading to low surface roughness, while also allowing for greater vertical stratification of the components in the bulk. Blended HBC:EPPTC films also exhibit an unique optical absorption feature near 590 nm, which we attribute to an altered crystalline packing of EPPTC in the presence of HBC. The significance of the local structure at molecular heterojunctions in blended active layer photovoltaic diodes is discussed.     

Effect of additives on the photovoltaic performance of coumarin-dye-sensitized nanocrystalline TiO2 solar cells

The effects of deoxycholic acid (DCA) and 4-tert-butylpyridine (TBP) as additives on the photovoltaic performance of coumarin-dye-sensitized nanocrystalline TiO2 solar cells were investigated. DCA coadsorption improved both the photocurrent and photovoltage of the solar cells, even though it decreased the amount of dye adsorbed on the TiO2 electrode. The improved photocurrent may arise from suppression of the deactivation of the excited state via quenching processes between dye molecules or a more negative LUMO level of the dye in the presence of DCA, resulting in a high electron-injection yield from the dye into TiO2. The increased photovoltage is probably due to suppression of recombination between the injected electrons and I3- ions on the TiO2 surface (dark current). The addition of TBP to the electrolyte also markedly improved the photovoltage and fill factor of the solar cell, and consequently, the total conversion efficiency increased from 3.6% to 7.5%. FT-IR spectroscopy indicated that a large amount of TBP was adsorbed on the dye-coated TiO2 films in the presence of Li cations. This result suggests that TBP, like DCA, suppressed the dark current on the TiO2 surface, which resulted in the improved photovoltage.     

The effect of solvent additives on morphology and excited-state dynamics in PCPDTBT:PCBM photovoltaic blends

The dependence of the thin film morphology and excited-state dynamics for the low-bandgap donor-acceptor copolymer poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b']-dithiophene)-alt-4,7-(2,1,3-benzothiadiazole)] (PCPDTBT) in pristine films and in blends (1:2) with [6,6]-phenyl-C(61)-butyric acid methyl ester (PCBM) on the use of the solvent additive 1,8-octanedithiol (ODT) is studied by solid-state nuclear magnetic resonance (NMR) spectroscopy and broadband visible and near-infrared pump-probe transient absorption spectroscopy (TAS) covering a spectral range from 500-2000 nm. The latter allows monitoring of the dynamics of excitons, bound interfacial charge-transfer (CT) states, and free charge carriers over a time range from femto- to microseconds. The broadband pump-probe experiments reveal that excitons are not only generated in the polymer but also in PCBM-rich domains. Depending on the morphology controlled by the use of solvent additives, polymer excitons undergo mainly ultrafast dissociation (<100 fs) in blends prepared without ODT or diffusion-limited dissociation in samples prepared with ODT. Excitons generated in PCBM diffuse slowly to the interface in both samples and undergo dissociation on a time scale of several tens of picoseconds up to hundreds of picoseconds. In both samples a significant fraction of the excitons creates strongly bound interfacial CT states, which exhibit subnanosecond geminate recombination. The total internal quantum efficiency loss due to geminate recombination is estimated to be 50% in samples prepared without ODT and is found to be reduced to 30% with ODT, indicating that more free charges are generated in samples prepared with solvent additives. In samples prepared with ODT, the free charges exhibit clear intensity-dependent recombination dynamics, which can be modeled by Langevin-type recombination with a bimolecular recombination coefficient of 6.3 × 10(-11) cm(3) s(-1). In samples prepared without ODT, an additional nanosecond recombination of polaron pairs is observed in conjunction with an increased intensity-independent trap-assisted nongeminate recombination of charges. Furthermore, a comparison of the triplet-induced absorption spectra of PCPDTBT with the charge-induced absorption in PCPDTBT:PCBM blends reveals that triplets have a very similar excited-state absorption spectrum compared to the free charge carriers, however, in contrast have a distinct intensity-independent lifetime. Overall, our results suggest that whether free charges or strongly bound CT states are created upon dissociation of excitons at the PCPDTBT:PCBM interface is determined instantaneously upon exciton dissociation and that once formed strongly bound CT states rapidly recombine and thus are unlikely to dissociate into free charges. The observation of a significantly larger bimolecular recombination coefficient than previously determined for poly(3-hexylthiophen-2,5-diyl):PCBM (P3HT:PCBM) and PCDTBT:PCBM samples indicates that nongeminate recombination of free charges considerably competes with charge extraction in PCPDTBT:PCBM photovoltaic devices.     

Replacing alkyl side chain of non-fullerene acceptor with siloxane-terminated side chain enables lower surface energy towards optimizing bulk-heterojunction morphology and high photovoltaic performance

Towards a good control of the morphology of bulk-heterojunction(BHJ) active layers for polymer solar cells(PSCs), selecting an appropriate side chain for a polymer donor and a nonfullerene acceptor(NFA) is very crucial. In this work, two novel NFAs i-IE-4F and i-IESi-4 F comprising alkyl and siloxane-terminated side chains on the central indacenodithiophene(IDT) core,respectively, were synthesized. Attaching the siloxane-terminated side chain to i-IESi-4 F affords surface energy(γ) of33.32 mN/m, much lower than that of 39.83 mN/m for i-IE-4F, supplying a big chance to tune miscibility with a polymer donor.Two fluorobenzotriazole-based polymer donors J52 and PBZ-2Si bearing alkyl and siloxane-terminated side chains, respectively, show γ values of 36.08 and 33.10 mN/m, respectively. The estimated Flory-Huggins interaction parameters(χD,A) indicate that the i-IESi-4 F is more miscible than i-IE-4F in pairing with J52 or PBZ-2Si. The resulting i-IESi-4 F-based blend film exhibits low film roughness and accompanies obviously improved BHJ uniformity. In PSCs, the J52:i-IESi-4F and PBZ-2Si:i-IESi-4 F active layers display power conversion efficiencies(PCEs) of 12.67% and 14.54%, respectively, all remarkably higher than PCEs≤ 7.34% of the i-IE-4F-based active layers. Interestingly, the PBZ-2Si:i-IESi-4 F active layer, a donor:acceptor blend system comprising siloxane-terminated side chains(DSi:ASimatching) with the highest BHJ miscibility due to the combinatory effect of the side chains, shows the highest efficiency, as supported by efficient exciton dissociation, the lowest bimolecular recombination, and the optimal charge transport. Our results demonstrate that attaching siloxane-terminated side chains to NFAs,as a side chain engineering, has big potential in lowering their surface energy towards fine control of BHJ morphology and leading to a better donor:acceptor blend system.     

The effect of the polyaniline morphology on the performance of polyaniline supercapacitors

The polyaniline (PANI) prepared by the pulse galvanostatic method (PGM) or the galvanostatic method on a stainless steel substrate from an aqueous solution of 0.5 mol/l H₂SO₄ with 0.2 mol/l aniline has been studied as an electroactive material in supercapacitors. The electrochemical performance of the PANI supercapacitor is characterized by cyclic voltammetry, a galvanostatic charge–discharge test and electrochemical impedance spectroscopy in NaClO₄ and HClO₄ mixed electrolyte. The results show that PANI films with different morphology and hence different capacitance are synthesized by controlling the synthesis methods and conditions. Owing to the double-layer capacitance and pseudocapacitance increase with increasing real surface area of PANI, the capacitive performances of PANI were enhanced with increasing real surface area of PANI. The highest capacitance is obtained for the PANI film with nanofibrous morphology. From charge–discharge studies of a nanofibrous PANI capacitor, a specific capacitance of 609 F/g and a specific energy density of 26.8 Wh/kg have been obtained at a discharge current density of 1.5 mA/cm². The PANI capacitor also shows little degradation of capacitance after 1,000 cycles. The effects of discharge current density and deposited charge of PANI on capacitance are investigated. The results indicate that the nanofibrous PANI prepared by the PGM is promising for supercapacitors.     

Lock-up function of fluorine enhances photovoltaic performance of polythiophene

Three model polythiophenes, PTCBT, PTCFBT and PFTCBT, have been synthesized to investigate the effect of fluorination on photovoltaic performance of polythiothenes. Compared with PTCBT, PFTCBT with F atom on TC unit shows a narrower optical bandgap (1.79 eV), higher crystallinity, and ideal morphology in the active layer, leading to a higher short-circuit current density (J _sc) of 11.84 mA/cm² and a power conversion efficiency (PCE) of 5.93%. The lock-up function of fluorine enhances polythiophene backbone planarity and molecular packing.