聚乙烯醇衍生的聚离子复合物的研究 Ⅲ．乙烯－乙烯醇共聚物的化学修饰及其复合物

通过化学修饰，在惭烯乙烯醇共聚物（ＥＶＡ）分子链上分别引入磺酸基、磷酸基或胺基等，制得具有聚离子性质ＥＶＡ衍生物，由灾些聚离子复合而形成的聚离子复俣，即使在含水状态也很少失其强度 。动态力学性能的测定表明，除聚离子之间物静电相互作用外，ＥＶＡＫ的乙撑链段及共聚物主链的结晶也对维持聚离子复合物的强度有贡献，在水－二甲基甲酰胺－无机强电解质三组分混合溶剂中，与使用ＮａＢｒ蔌ＬｉＢｒ的体系比较。聚离子复     

蠕虫状聚离子复合型胶束的合成、组装和胶体稳定性

采用开环聚合方法制备了嵌段共聚物聚乙二醇-聚乙烯亚胺(PEG-b-PEI), 通过静电组装方法使其与质粒DNA(pDNA)在溶液中自发构筑成蠕虫状聚离子复合型胶束(PICmicelle), 利用原子力显微镜、 动态光散射、 Zeta电势和凝胶电泳等方法研究了血液或细胞间质中各种因素对胶束稳定性的影响. 结果表明, 在蠕虫状聚离子复合型胶束中, PEI和pDNA通过静电吸引构成疏水性内核, 而亲水性的PEG分子作为保护型外壳包裹在内核的表面. 在保持PEG链段长度不变的前提下, 增加PEI链段长度可明显增强PEI与pDNA的静电结合力, 有效地防止了NaCl对胶体结构的破坏, 而且有助于抑制阴离子的取代. 但增加PEI链段长度会导致胶束表面PEG分子含量的降低, 不利于胶束抵抗蛋白质的吸附和DNA酶的降解. 因此合理地调整PEG-b-PEI分子的结构, 对于获得高效、 安全和稳定的蠕虫状聚离子胶束具有重要意义.     

离子交联型聚合物的离子聚集形态研究进展

系统评述了离子含量、抗衡离子、离子基团、基体近程链结构(柔顺性、介电常数、基团空间位阻、支化、共价交联)、中和度、离子沿主链分布结构、环境条件(温度、溶剂、水分)及制备历史(熔融压制、溶液铸膜、再沉淀、高温退火)等对离子交联型聚合物(以下简称离聚物)的离子聚集形态(参与聚集离子比例、离子簇的形状、尺寸、聚集数、数密度、分布及内部配位结构)的影响。在此基础上,指出离子簇内部是否存在原子的有序排列、离聚物低温差示扫描量热(DSC)吸热峰的起源、现有离子跃迁理论的缺陷及基体远程链结构—分子量对离子簇形态的效应为当前亟待解决的离子聚集形态方面的四个基本问题。尤其对于离子跃迁理论的扩展与完善提出了建议:不仅要考虑离子相互作用强度这一结构因素,亦须涵盖离子簇聚集数(离子簇近围的链段紧密堆砌程度)及离子簇数密度(离子交联密度)这两个形态因素,如此才能合理诠释或预测离聚物的结构-性能关系。     

聚离子液体功能材料研究进展

聚离子液体(PILs)材料兼具离子液体和聚合物的性质, 近年来已经在高分子化学、材料科学及能源科学等领域得到初步应用, 并引起了人们广泛关注. 本论文介绍了聚离子液体的合成, 综述其在(准)固态电解质、燃料电池聚电解质膜、刺激响应性功能材料, 以及碳材料等相关领域的研究与应用.     

聚偏氟乙烯膜三维离子传输通道的构建及其在全钒液流电池中的性能研究

随着新能源技术的不断发展, 大规模储能技术受到了广泛的关注. 全钒液流电池因其容量和功率设计灵活、安全可靠、寿命长等优势成为发展较快的储能电池之一. 离子膜作为液流电池的关键部件, 对电池的能量转化效率、寿命和成本具有显著影响. 本工作以高化学稳定性的聚偏氟乙烯作为膜材料, 利用聚乙二醇和聚乙烯吡咯烷酮分别作为模板和稳定剂, 在聚偏氟乙烯膜内成功构建了具有较好H/V离子选择性的三维离子传输通道. 电池性能测试表明, 该聚偏氟乙烯(PVDF)离子膜有着出色的化学稳定性, 在100 mA•cm^-2电流密度下, 具有98%以上的电流效率和83.5%的能量效率. 此外, 聚偏氟乙烯具有价格低的显著特点, 使其在全钒液流电池中有较好的应用前景.     

离子液体增塑改性玉米淀粉/聚丁二酸丁二醇酯共混材料的结构与性能

为考察离子液体对淀粉/聚丁二酸丁二醇酯(PBS)的作用效果,降低淀粉/PBS的脆性,以离子液体(1-丁基-3-甲基咪唑氯盐[BMIM]Cl)作为增塑改性剂通过熔融共混法制备了玉米淀粉/聚丁二酸丁二醇酯(PBS)共混材料,采用红外光谱(FTIR)、扫描电镜(SEM)、热重分析(TGA)、X射线衍射分析(XRD)及力学性能测试方法研究了[BMIM]Cl对淀粉/PBS共混材料结构和性能的影响.结果表明,[BMIM]Cl能与淀粉/PBS分子发生强相互作用,破坏淀粉/PBS共混物中原有的氢键与结晶结构,增强界面相互作用,改善相容性,进而改变淀粉/PBS共混材料的结构与性能;[BMIM]Cl的加入不影响淀粉/PBS的热稳定性,可使材料玻璃化转变温度(Tg)、结晶温度(Tc)、冷结晶温度(Tcc)及结晶度(Xc)降低.[BMIM]Cl具有显著降低淀粉/PBS脆性的作用,使其断裂伸长率大幅度增加,拉伸强度和弹性模量降低.     

接枝型聚两性电解质CS-g-PLGA的合成及溶液性质

合成了以壳聚糖(CS)为主链、 聚(L-谷氨酸)(PLGA)为侧链的接枝型聚两性电解质CS-g-PLGA(CGA), 表征了其结构与组成, 探讨了pH值、 离子强度和离子种类等对CGA水溶液性质的影响. 研究发现, 随着溶液离子强度的增大, CGA的等电点(IEP)移向高pH值; 离子水化半径越大, 对CGA分子中相反电荷的屏蔽作用越弱, 对IEP的影响越小; CGA中氨基和羧基相对含量越接近, 对溶液离子强度的变化越敏感. 此外, CGA具有显著的pH响应性, 在酸性及碱性溶液中分别形成结构相反的聚集体. 在CS主链氨基含量相近的条件下, 聚集体的稳定性随PLGA链长的增加而提高. 酸性溶液中聚集体粒径取决于CS主链的电荷数; 碱性溶液中PLGA侧链越长则平均粒径越大.     

掺杂离子对聚吡咯膜的电化学容量性能的影响

用电化学方法制备了分别以对甲基苯磺酸根(TOS-), 高氯酸根(ClO-4)和氯离子(Cl-)掺杂的聚吡咯(PPy)膜. 用循环伏安(CV)、恒电流充放电和电化学阻抗谱(EIS)等测试了它们的电化学容量性能. 用扫描电镜(SEM)和X射线衍射(XRD)分别研究了这三种PPy膜的形貌和结构. 研究发现, 由于具有疏松多孔的形貌和更有序的分子链结构, PPy-TOS和 PPy-Cl膜具有较好的充放电能力, 在深度充放电时仍具有很小的电化学电阻, 其离子扩散接近理想电容器的离子扩散机理. PPy-Cl(聚合电量2 mAh·cm-2)的比容量在扫描速率为5 mV·s-1时高达270 F·g-1, 扫描速率200 mV·s-1时仍高达175 F·g-1, 特别是, 其比能量高达35.3 mWh·g-1. PPy-TOS由于有质量较大的掺杂离子(TOS-)因而比容量略低(146 F·g-1, 扫描速率5 mV·s-1), 但具有超快速充放电能力, 在扫描速率为200 mV·s-1时, 比容量为123.6 F·g-1, 其比功率高达10 W·g-1. 并且, 两种电极材料均具有稳定的电化学循环性能.     

重氮树脂型聚离子复合物

高分子化合物沿分子链(主链和侧链)排列多量可离解基团(每个链节可有1～2个)称聚电解质或聚离子^[1]。聚电解质在水中可离解成两部分,若离解后,聚合物链带负电荷,称聚阴离子电解质或聚负离子;若带正电荷,称聚阳离子电解质或聚正离子。     

交联聚天冬氨酸基聚离子胶束的制备与表征

通过胺端基聚乙二醇(CH3O-PEG-NH2)开环聚琥珀酰亚胺(PSI), 进一步碱解和胺解制备了聚乙二醇接枝聚天冬氨酸(PEG-g-PAsp)和聚乙二醇接枝聚乙二胺基天冬酰胺(PEG-g-PDEA)两种聚天冬氨酸衍生物. 利用它们之间的静电相互作用, 在磷酸缓冲液中形成了以PEG为壳、聚天冬氨酸复合物为核的聚离子胶束. 研究发现, 该聚离子胶束粒子呈球形, 粒径约为70 nm, 且粒径分布较窄. 然而, 体系的稳定性受溶液的pH和盐离子强度影响较大. 通过戊二醛交联PEG-g-PDEA中的伯胺可以有效提高该聚离子胶束对pH和盐离子强度的稳定性.     

表面修饰乙烯－乙烯醇共聚物膜的“原地”聚离子复合化及其若干性能

he ethylene-vinyl alcohol copolymer membrane with polyionically complexationalized layer has been prepared by in situ polyionic complexation from cationically modified surface of EVAL membrane and phosphorylated EVAL aqueous solution, which can be considered as a feasible route to modify the surface of membrane for improving the properties , and which is a way to avoid the using of shielding solvent for the processing of polygonic complexes. The condition for the phosphorylation of EVAL has been studied. The effect of the chemical composition of the polyionic complex membrane on the contact angle, water con-tent,mechanical and thermal properties,as well as blood compatibility have been investigated.     

表面修饰乙烯－乙烯醇共聚物膜的“原地”聚离子复合化及其若干性能

表面修饰乙烯－乙烯醇共聚物膜的“原地”聚离子复合化及其若干性能张军，王大力，刘新三（天津市合成材料研究所，天津，３００２２０）李福绵（北京大学化学系，北京，１００８７１）关键词聚离子复合物，“原地”聚离子复合，磷酸酯化，乙烯－乙烯醇共聚物膜聚离子复合...     

Polysaccharide films built by simultaneous or alternate spray: a rapid way to engineer biomaterial surfaces

We investigated polysaccharide films obtained by simultaneous and alternate spraying of a chitosan (CHI) solution as polycation and hyaluronic acid (HA), alginate (ALG), and chondroitin sulfate (CS) solutions as polyanions. For simultaneous spraying, the film thickness increases linearly with the cumulative spraying time and passes through a maximum for polyanion/CHI molar charge ratios lying between 0.6 and 1.2. The size of polyanion/CHI complexes formed in solution was compared with the simultaneously sprayed film growth rate as a function of the polyanion/CHI molar charge ratio. A good correlation was found. This suggests the importance of polyanion/polycation complexation in the simultaneous spraying process. Depending on the system, the film topography is either liquid-like or granular. Film biocompatibility was evaluated using human gingival fibroblasts. A small or no difference is observed in cell viability and adhesion between the two deposition processes. The CHI/HA system appears to be the best for cell adhesion inducing the clustering of CD44, a cell surface HA receptor, at the membrane of cells. Simultaneous or alternate spraying of CHI/HA appears thus to be a convenient and fast procedure for biomaterial surface modifications.     

Selective membranes with biologically active surface

Composite membranes have been developed for media where accumulation of pathogenic microorganisms on the membrane surface is possible. It has been proposed to use as membrane skin layer a polymer nanocomposite modified with detonation nanodiamonds containing surface-bound dibutyltin dilaurate as biologically active substance, which should ensure self-cleaning of the membrane surface.     

Surface characterization of argon-plasma-modified perfluorosulfonic acid membranes

The perfluorosulfonic acid membranes which are used in direct methanol fuel cells were modified with argon plasma under various conditions, and the physicochemical and transport properties of the resulting membranes were investigated using various analytical techniques. The plasma treatment was found to change the surface morphology and physicochemical properties of the membranes. The surface roughness of the membranes was increased by the etching effect of plasma. From the FTIR and XPS analyses, the incorporation of new oxygen functionalities, such as the peroxide group, was confirmed. The breakage of both the sulfonic acid groups and ether linkages were also found to cause an increase in the equivalent weight of the modified skin layer of the membrane. The incident water contact angle of the modified membrane in a dry state decreased with an increased plasma treatment, because of the hydrophilic groups that developed on the membrane surface. The time-dependent water contact angle, however, increased in proportion to the extent of the plasma treatment, due to the reduced concentration of sulfonic acid groups. Although the equilibrium water uptake of the modified membrane was almost invariable because of the negligible thickness of the modified skin layer, the transport properties of the membrane such as methanol permeability and proton conductivity were significantly reduced.     

Fabrication and hemocompatibility of cell outer membrane mimetic surfaces on chitosan by layer by layer assembly with polyanion bearing phosphorylcholine groups

Three random copolymers poly(2-methacryloyloxyethyl phosphorylcholine-co-methacrylic acid) (PMAs) were synthesized by free radical polymerization of 2-methacryloyloxyethyl phosphorylcholine (MPC) and methacrylic acid (MA) with different monomer ratios under monomer-starved conditions. The synthesized PMA polyanions were assembled on chitosan (CS) film surfaces via electrostatic interactions. Using layer by layer (LbL) assembly with PMA polyanion and chitosan polycation, PMA/CS multilayer thin films with phosphorylcholine groups on the outer surfaces were fabricated. The modified surfaces were characterized by dynamic contact angle (DCA), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Hemocompatibility of the surfaces was estimated by protein adsorption and platelet adhesion measurements. The results indicated that cell outer membrane mimetic structures were formed on the modified surfaces with PMA as the outermost layer, and the hemocompatibility of the modified surfaces was significantly improved. This facile method of fabricating cell outer membrane mimetic surfaces may have potential applications in the fields of hemocompatible coatings, drug delivery, and tissue engineering.     

Modification of ceramic membranes by alcohol adsorption

This study aims at modifying ceramic membranes by means of alcohol chemisorption. Composite ceramic membranes with a skin layer of γ-alumina were used. First, the adsorption of several alcohol on powdered γ-alumina was investigated emphasising the thermal stability of the adsorbed compounds. Later, a commercial γ-alumina membrane was modified by alcohol adsorption. The permeability of water and several organic compounds was obtained for both the non-modified and modified ceramic membrane. Also, its isoelectric point was determined. The results prove that all the alcohol were readily adsorbed on powdered γ-alumina not only physically but also chemically forming an alkoxide. The chemisorbed alcohol was stable up to 200°C. Beyond this temperature, the alkoxide breaks up releasing the alcohol although the alkoxide also can react yielding an olefin or ether. The ceramic membrane was also successfully modified by alcohol adsorption. The layer of chemisorbed alcohol imparts hydrophobic characteristics to the membrane surface, so water permeability decreases significantly. This cannot be merely explained by pore size reduction due to the adsorbed layer. Thermal treatment at 250°C recovered original permeability with only minor damage to the membrane.     

Permeate flow in hexagonal 19-channel inorganic membrane under filtration and backflush operating modes

Numerical simulations and experimental study of incompressible Newtonian permeate flow in porous support of hexagonal 19-channel inorganic membrane are presented both for filtration and backflush operating modes. Under several simplifying assumptions the problem could be treated as two-dimensional potential flow. The mathematical model was solved using finite element method. The results of numerical simulations show that the contributions of particular channels to the total permeate flux are not equal and depend on the ratio of skin layer to porous support permeability as well as on the distance of a channel from the membrane outer surface. For membranes with high permeability of skin layer there is an area of nearly constant pressure around inner channels and their contribution to total flux is negligible. This effect will probably be more pronounced in backflush operating mode while in filtration mode possible dynamic membrane adds a resistance to that of skin layer which leads to more uniform permeate flux distribution. Qualitative trends of the numerical simulations were verified by experiments with ceramic 19-channel membranes of Membralox® type in backflush operating mode.     

Electrostatic interaction of ion-penetrable membranes. Effects of ionic solubility

An analytic, approximate expression for the electrostatic interaction between two membranes immersed in an electrolyte solution is derived on the basis of a simple membrane model. This model assumes that the membrane has a surface layer in which charged groups are uniformly distributed and that electrolyte ions can penetrate into the surface layer. The partition coefficients of cations and anions between the solution and the surface layer, which are related to their solubilities in the surface layer, may be different from unity.The electrostatic interaction depends on the ionic partition coefficients between the solution and the surface layer, and the relative permittivity of the surface layer, as well as on the membrane-fixed charges, the electrolyte concentration in the solution, and the surface layer thickness. It is shown, in particular, that even where the charge layer has no fixed charges, the electrostatic interaction force can be produced if the solubilities of cations and anions are different in the surface layer.     

Lability criteria for successive metal complexes in steady-state planar diffusion

The lability of sequential metal complexes, ML, ML2, ML3, ... , up to a general 1:n metal/ligand stoichiometric ratio is considered for the case of metal ions (M) being accumulated at a surface (analytical sensor or organism). The analytical solution for the steady-state diffusion of M within a sequential complexation scheme allows quantification of the contribution from the dissociation of all of the complex species to the metal flux through the so-called lability degree, xi. A lability degree for each sequential complexation step is also defined which, due to the sequential character of the complexation scheme, depends not only on the proper kinetic constants of the given complexation step but also on the kinetics of the previous ones. When all contributions from the complexes are diffusion limited, the system is fully labile and xi=1. To provide simple lability criteria, the reaction layer approximation is extended to specifically deal with this sequential complexation scheme, so that a reaction layer thickness is defined when the existence of one particular rate-limiting step is assumed. Expressions for the classical lability parameter, L, are formulated using the reaction layer approximation. The change of the lability of the system as the diffusion layer thickness is modified is analyzed in detail. The contribution of the complex flux reflects the evolution of the system from labile to inert as the thickness of the sensor is appropriately decreased.