铁钝化多孔硅的制备及光致发光机理研究

采用水热腐蚀法在相同环境下制备了不同晶型的铁钝化多孔硅样品。同一样品表面具有相似的孔隙结构,不同样品形貌存在差异。在300 nm光激发下,样品发光峰位于618 nm附近,半高宽约为132 nm。傅立叶红外变换光谱显示样品中有强的Si—Si、Si—O—Si、O y—Si—H x化学键振动吸收。结果表明,水热腐蚀法制备的铁钝化多孔硅表面形貌与腐蚀过程的局域电极分布关系密切。样品的光致发光行为可归因于量子限制-发光中心作用,并受非桥氧空穴发光中心数量影响。     

水热腐蚀时间对铁钝化多孔硅表面形貌和光致发光的影响

采用水热腐蚀法制备了4个腐蚀时间不同的铁钝化多孔硅样品,铁钝化多孔硅样品表面呈海绵结构,随着腐蚀时间增加,样品表面的平整度下降,腐蚀孔尺寸差别有增大的趋势。在250nm光激发下,样品发光峰位于620nm附近,半峰全宽约130nm。腐蚀时间从10min增加到40min,4个样品的发光峰并未出现定向的红移或蓝移。结合样品傅里叶变换红外吸收光谱的结果,铁钝化多孔硅的光致发光行为可归因于量子限制-发光中心作用,相应的辐射复合发光中心为非桥氧空穴。     

非桥氧空穴发光中心对铁钝化多孔硅光致发光的影响

采用水热腐蚀法制备了铁钝化多孔硅样品,样品光致发光谱的荧光峰位于2.0eV附近,半峰宽约为0.40eV。激发波长从240nm增大到440nm的过程中,荧光峰先红移再蓝移,最后基本稳定,变化曲线呈勺型。通过分析15片发光多孔硅样品的统计结果,发现荧光峰逆转所对应的激发波长位于330nm附近,相应的激发光子能量约为3.8eV。样品光致发光谱随激发波长的勺型变化过程与≡Si—O↑和≡Si—O↑…H—O—Si≡两类非桥氧空穴发光中心共同作用时的发光行为一致。     

少子寿命和表面形貌与多孔硅发光性能的关系

研究了不同时间腐蚀的多孔硅的光致发光性能与多孔硅的表面形貌和少子寿命之间的关系。结果表明,多孔硅的发光来自与氧空位有关的缺陷,而多孔硅表面的氢原子能够钝化多孔硅表面的非辐射中心从而提高多孔硅的发光效率。多孔硅的空隙度随腐蚀时间的延长而增大,这也导致了多孔硅的少子寿命的降低,从而造成多孔硅的光致发光效率随多孔硅空隙度的增大以及少子寿命的降低而提高。另外,原子力显微照片表明长时间的腐蚀使多孔硅表面层被化学腐蚀,从而降低了多孔硅表面的粗糙度。     

n型多孔硅光致发光研究

对在无光照条件下,电化学阳极腐蚀方法制备的n型多孔硅进行了光致发光性能研究.在325nm的激发光照射下,多孔硅样品的发光峰在620nm处,其橙红色的发光肉眼可见,并随阳极电流密度与腐蚀时间乘积的增加.先增强,后减弱.其发光峰位置与量子限制效应、表面态及缺陷态有关,发光强度与样品表面深度较浅孔洞所占的面积比成正比.     

氢等离子体气氛中退火多孔硅的表面和光荧光特性

用电化学腐蚀法制备了多孔硅(PS),在氢等离子体气氛中不同温度下对多孔硅样品进行了退火处理,并进行了光致发光(PL)谱和原子力显微镜(AFM)表面形貌的测量。不同退火温度给PS表面形态带来较大变化,也影响了其PL谱特性。在退火的样品中观察到的PL谱高效蓝光和紫光谱带,我们认为主要源于量子限制发光峰和非平衡载流子被带隙中浅杂质能级所俘获而引起的辐射复合所产生的。在420—450℃退火处理的多孔硅的PL谱上观察到了一个未见诸于报道的紫光新谱带(3．24eV,382nm),其发光机理有待于进一步研究。     

铁钝化多孔硅中的输运性质

采用水热法制备了发光强度强且不衰减、峰位不蓝移的铁钝化多孔硅。标准四引线法测得的电阻一温度结果表明杂质能级是输运的主宰者;电流一电压结果说明当有电流流过样品时会有明显的热效应．考虑到金属电极和铁钝化多孔硅之间形成的肖特基势垒会对样品的输运性质产生影响,采用其平面的两引线法测量了铁钝化多孔硅样品在不同温度下的电流一电压特性,发现隧道模型可以很好地拟和这些结果这些研究结果指出作为未来的多孔硅光电集成器件;通过多孔硅的电流必须限定在一定的范围１引言 １９９０年英国的Ｌ．Ｔ,Ｃａｎｈａｍ首次成功获得在室…     

多孔硅紫外发光性质的研究

采用水热刻蚀技术制备多孔硅粉末。紫外激光244 nm激发时,多孔硅呈现出310 nm的强紫外发光。随着研磨时间的延长,多孔硅结构消失,紫外发光带也随之消失。氧气热处理后,多孔硅表面被氧化生成氧化硅薄层,同样造成紫外发光带的消失。我们认为310 nm紫外发光来源于硅纳米结构中电子和空穴的直接禁带结构辐射复合。     

掺钛化学腐蚀法制备发光稳定的多孔硅

本文采用掺钛化学腐蚀法制备出了发光稳定性和均匀性都较好的多孔硅 (PS)。存放和退火试验表明 ,光致发光 (PL)谱峰位不蓝移 ,强度不衰减。多孔硅发光稳定性的提高归因于制备过程中样品表面原位氧和钛的钝化。钛的浓度和腐蚀时间对PL强度有明显影响 ,最佳钛浓度约为 0 0 8mol·L- 1 ,最佳腐蚀时间约为 2 0min。掺钛化学腐蚀法制备的PS的光激发过程符合量子限域机制 ,而其PL过程却与量子限域模型不符 ,这表明其光发射过程不是带 带直接跃迁产生的 ,即存在一个表面态     

矫顽力可调的多孔硅基Fe膜

采用电化学腐蚀法制备了不同多孔度的多孔硅(PS),再通过磁控溅射法在该PS衬底上沉积了一定厚度的Fe膜;并对样品进行了X射线衍射的结构分析、扫描隧道显微技术的表面形貌观察和磁光克尔效应的测量.发现在同一Fe膜厚度下，相对于参考样品硅上的Fe膜，多孔硅上Fe膜的矫顽力更大;同时观察到多孔硅基Fe膜随着PS多孔度的增加，矫顽力相应变大;而对于多孔度相同的多孔硅基样品,随着Fe膜厚度的增加矫顽力却逐步减小.得出了多孔硅特有的海绵状疏松结构能有效调节Fe膜矫顽力大小的结论. 关键词： 多孔硅 海绵状结构 Fe薄膜 矫顽力     

Simulation and fabrication study of porous silicon photonic crystal

The present work reports design and fabrication of porous silicon based one-dimensional (1D) photonic crystal. Distributed Bragg reflector (DBR) is a 1D photonic crystal composed of multilayer stack of high and low refractive index layers. Design of porous silicon DBR is a complex one and requires appropriate control in optical parameters of its constituent layers. In order to design DBR, two porous silicon single layer samples were fabricated using current density of 10 and 50 mA/cm². Optical characterization of single layer samples showed series of interference fringes. Reflective interferometric Fourier transform spectroscopy (RIFTS) method was employed to determine optical constants of porous silicon single layers. DBR simulation was carried out based on transfer matrix method. DBR was then fabricated using optical parameters obtained from RIFTS method. Reflection bandwidth of prepared DBR was found to be 216 nm, which is comparable to the simulated value of 203 nm.     

绝缘衬底上高密度均匀纳米硅量子点的形成与表面形貌

利用等离子体增强化学气相淀积技术，在绝缘氮化硅(SiNx)衬底上制备超薄非晶硅(aSi：H)薄膜，通过超短脉冲激光辐照与准静态常规热退火技术处理，制备出高密度、均匀纳米硅(ncSi)量子点.使用原子力显微镜对处理前后样品的表面形貌进行了研究，发现激光辐照能量密度增加的同时，所形成的ncSi尺寸也随之增加.在合适的能量密度范围内，可以得到面密度大于10.11cm^2、尺寸分布标准偏差小于20％的10 nm ncSi量子点薄膜，表明所制备的ncSi量子点具有较好的均匀性及较高的面密度.同时，对ncS i量子点 关键词： 纳米硅 激光诱导 尺寸分布     

Laser-induced etching of silicon

Conventional fabrication method of porous silicon is anodisation of single crystal silicon in hydrofluoric acid. In this report, we show that it is possible to fabricate porous silicon by laser-induced etching. An earlier report by us has demonstrated the dependence of porous silicon photoluminescence characteristic on the etching laser wavelength [1]. Here we used 780 nm line from a diode laser as the etching source, and the optimum etching conditions were obtained. A simple model was proposed to explain the etching process. Scanning Electron Microscope (SEM) images of the samples support the proposed process.     

Study on the thermal isolation properties of porous silicon photonic crystal

The thermal isolation properties of porous silicon photonic crystal structures have been designed and discussed theoretically. Excellent thermal isolation properties can be obtained on such a porous silicon photonic crystal, even better than that of porous silicon with high porosity. Due to the excellent thermal isolation properties of the porous silicon photonic crystal structures, they can be used as the thermal isolation substrates in infrared detectors     

Tunable photoluminescence of porous silicon by liquid crystal infiltration

The photoluminescence (PL) of porous silicon films has been investigated as a function of the amount of liquid crystal molecules that are infiltrated into the constricted geometry of the porous silicon films. A typical nematic liquid crystal 4-pentyl-4′-cyanobiphenyl was employed in our experiment as the filler to modify the PL of porous silicon. It is found that the originally red PL of porous silicon films can be tuned to blue by simply adjusting the amount of liquid crystal molecules in the microchannels of the porous films. The chromaticity coordinates are calculated for the recorded PL spectra. The mechanism of the tunable PL is discussed. Our results have demonstrated that the luminescent properties of porous silicon films can be efficiently tuned by liquid crystal infiltration.     

激发波长对多孔硅荧光特性的影响

用荧光光谱仪测量了多孔硅样品的任一给定点的荧光特性与激发波长的依赖关系, 发现当激发波长从650 nm变到340 nm时,该点的荧光谱峰位从780 nm连续蓝移到490 nm。用扫描电子显微镜(SEM)对多孔硅的截面进行了分析,结果显示多孔硅具有分形特性,这同作者的计算机模拟结果一致。结合多孔硅样品的激发光谱测量结果,多孔硅的荧光特性随激发波长改变的现象可以归因于多孔硅的分形结构以及量子尺寸效应。     

Preparation of silica nanowires using porous silicon as Si source

This very paper is focusing on the preparation of silica nano-wires via annealing porous silicon wafer at 1200 °C in H₂ atmosphere and without the assistant metal catalysts. X-ray diffraction, X-ray energy dispersion spectroscopy, scanning electron microscopy, high-resolution transmission electron microscopy and selected area diffraction technology have been employed for characterizing the structures, the morphology and the chemical components of the nano-wires prepared, respectively. It is found that the diameter and the length of the nano-wires were about 100 nm and tens micron, respectively. Meanwhile, it is also necessary to be pointed out that silica NWs only formed in the cracks of porous wafers, where the stress induced both by the electro-chemical etching procedure for the porous silicon preparation and nanowires growth procedure is believed to be lower than that at the center of the island. Therefore, a stress-driven mechanism for the NWs growth model is proposed to explain these findings.     

Enhancement of fluorescence of porous silicon upon saturation by liquid crystal

The fluorescence of samples of porous silicon of various morphologies that are filled with a liquid crystal (LC), n-pentyl-n′-cyanobiphenyl (5CB), is studied. The fluorescence spectra of the sample, along with the long-wavelength band of porous silicon with a maximum in the range 627–667 nm, exhibit a short-wavelength band of 5CB with a maximum in the range 385–410 nm. The radiative relaxation times of porous silicon and 5CB lie in the micro- and nanosecond ranges, respectively. It is found that the filling of pores with 5CB enhances the fluorescence of porous silicon by two to three times. This enhancement is caused by non-radiative energy transfer from 5CB to the porous matrix as a result of efficient interactions between LC molecules and pore walls. Using IR spectroscopy, it is shown that the formation of hydrogen bonds between cyano groups of 5CB molecules and silanol groups of pore surface is the predominant type of these interactions. A transfer mechanism is suggested according to which excited associates of 5CB molecules transfer their energy via surface channels to excitons of porous silicon, enhancing its fluorescence.     

多孔硅量子点的受激辐射：陷阱态的作用

 经激光辐照和高温退火后能够在硅基上生成氧化多孔硅结构。用514 nm的激光泵浦,观测到该多孔硅的受激辐射。当激励强度超过阈值时,在650～750 nm区域有很强的受激发光峰。这些受激发光峰的半高宽小于0.5 nm。激光辐照和高温退火后,在样品上能形成某些特殊的氧化结构。在傅里叶红外光谱分析中,显示有硅氧双键或硅氧桥键在硅表面形成。计算结果表明：当硅氧双键或硅氧桥键形成时,电子的陷阱态出现在纳晶硅的带隙中。价带顶和陷阱态之间的粒子数反转是解释这种受激辐射的关键。     

Beam focusing upon the reflection from crystals and multilayer periodic structures with variable period

The experimental spectral dependence of the intensity of the second harmonic (SH) generated in microcavities based on porous silicon photonic crystal demonstrates resonant intensity enhancement (by a factor of ～2×10²) in the vicinity of the cavity mode and at the edges of the photonic band gap. The enhancement is due to the combined effect of pump radiation localization inside the microcavity, multiple SH interference in the photonic crystal, and two-photon resonance of the porous silicon quadratic susceptibility at the SH frequency.