In-situ deactivation of packed columns for SFC

Residual adsorptive activity of reversed phase (RP) column packings used in supercritical fluid chromatography (SFC) can be significantly reduced by a dynamic in-situ silanization with diphenyltetramethyldisilazane (DPTMDS). RP-materials thus deactivated were characterized both chromatographically and by solid-phase ²⁹Si NMR.     

Supercritical fluid chromatographic separation of polychlorinated biphenyls (PCBs) using a negative temperature gradient for density programming

The technical PCB mixtures Aroclol and Clophen have been analyzed by packed column supercritical fluid chromatography using negative temperature programming. The chromatographic method was successfully applied to the analysis of PCBs, polycyclic aromatic hydrocarbons, and polychlorinated dibenzo-p-dioxins in extracts from environmental matrices.     

Use of specially designed columns for antioxidants and antimicrobials enrichment by preparative supercritical fluid chromatography

A new, specially designed column has been developed for fractionation of supercritical fluid extract of rosemary by using a preparative supercritical fluid chromatography system (Prep-SFC). The column evaluated in this work was prepared using a new packing method consisting of a combination of slurry and supercritical CO2 with commercial silica particles coated with a stationary phase commonly used in gas chromatography, such as SE-54 (5% phenyl-, 95% methylsilicone). The new packing procedure provided columns with reasonable efficiencies, with high stability and useful at high-pressure range. A 25 cm x 10 mm i.d. column packed with silica particles coated with 3% of SE-54 was prepared, and its separation power was tested for isolating fractions with high antioxidant and/or antimicrobial activity from a supercritical rosemary extract. The SFC conditions were selected based on a previous work done with a commercial LC-Diol packed column (130 bar, 80 degrees C), and different percentages of modifier in the mobile phase were tested (5 and 10%). Two cyclones were employed to collect the fractions which were then characterized by HPLC-diode array detection (DAD), GC, and in vitro antioxidant and antimicrobial assays. The use of coated packed columns allowed the fractionation of a complex mixture of rosemary supercritical extract with a minimum amount of modifier in the mobile phase (5% ethanol). At the optimum conditions it was possible to obtain two very active fractions in terms of antioxidant and antimicrobial activity, with no residual rosemary aroma and with improved activities compared to the original supercritical extract.     

Density gradients in packed columns: II. Effects of density gradients on efficiency in supercritical fluid separations

To investigate how fluid compressibility affects efficiency in supercritical fluid separations, band dispersion along a packed capillary column was measured from on-column elution rate profiles obtained under solvating gas chromatography (SGC) conditions; this allowed efficiency to be determined with respect to position along the column. Theoretical efficiency was also modeled. The model indicates that the primary cause of band broadening in SGC is high mobile phase velocity near the column outlet. However, the experimental results show that significant band broadening also occurs near the column inlet in a region that corresponds to high elution rates of the analyte. On-column detection also revealed spatial focusing of the analyte as it moves down the column density gradient.     

Serially coupled capillary columns supercritical fluid chromatography with a coupling restrictor.

A serially coupled column system for capillary supercritical fluid chromatography was constructed by connecting two capillary columns of different polarities using or without using a coupling restrictor. The influence of the column sequence, the size of the coupling restrictor and the column temperature on the polarity of the system were studied. The system without a coupling restrictor (the directly coupled system) provided an intermediate polarity between two columns, depending on the column geometry, such as the film thickness and column length, although it slightly shifted to that of the first column. In the system with a coupling restrictor, the contribution of the second column to the overall retention increased with its resistance. The use of a coupling restrictor allowed to control the polarity of the coupled system virtually over the whole range between two columns. The temperature was an additional effective parameter for tuning the polarity of the system.     

Fast supercritical fluid chromatography of polymers using packed capillary columns

Summary Fast separations of perfluorinated polyethers and polymethylsiloxanes that are composed of 50–80 oligomers were demonstrated in packed capillary column supercritical fluid chromatography (SFC) using a carbon dioxide mobile phase. Separations were accomplished within 10 min using a 13 cm×250 μm i.d. column packed with 2 μm porous octadecyl bonded silica (ODS) particles. Effects of particle diameter of the packing material and pressure programming on separation were investigated, and packed column SFC was compared with open tubular column SFC. Results show that as the particle diameter was decreased from 5 to 3 to 2 μm and the column length was reduced from 85 to 43 to 13 cm, the separation time could be reduced from 70 to 20 to 10 min while still maintaining similar separation (resolution). Short columns packed with small porous particles are very suitable for fast SFC separations of polymers.     

Recent advances in sample introduction for supercritical fluid chromatography

New strategies for sample introduction in supercritical fluid chromatography are reviewed. Both open tubular and packed column systems are examined as the injection demands of each column type are addressed. In addition to advances made in solvent injection methods, supercritical fluid extraction (SFE) is discussed as a solventless injection technique for supercritical fluid chromatography.     

On-line supercritical fluid chromatography with Fourier transform infrared spectrometric detection employing packed columns and a high pressure lightpipe flow cell

Summary The coupling of packed-column supercritical fluid chromatography (SFC) with Fourier-transform infrared spectrometry (FTIR) is demonstrated. The interface used for SFC-FTIR experiments is based on the lightpipe used for GC-FTIR, but it has been designed to withstand the high-pressure constraints of SFC. When used with beam condensing optics, this SFC-FTIR lightpipe flow cell has allowed detection limits as low as 270ng (3×N_p-p) of injected acetophenone. Separation of a seven-component model mixture is shown on a silica bondedphase phenyl column. The on-line infrared spectra obtained are high-quality and readily identifiable. Spectral features of high-pressure carbon dioxide (subcritical vs. supercritical) are discussed with respect to infrared transparency in the flow cell SFC-FTIR experiment.     

Supercritical fluid extraction of PCBs in tandem with high resolution gas chromatography in environmental analysis

A simple method has been developed for the direct coupling of supercritical fluid extractions (SFE) with a high resolution gas chromatograph (HRGC) equipped with an electron capture detector (ECD). SFE conditions have been investigated for polychlorinated biphenyls (PCBs) from sediments in terms of mobile phase, entrainer, pressure, temperature, and mass-flow through the extractor. Dynamic leaching and static steady-state extractions were compared. Extraction efficiencies of up to 100% in less than 15 minutes have been obtained. The extracted PCBs are quantitatively transferred into a fused silica open tubular column (OTC). Determination of PCBs was tested on certified sediment from National Water Research Institute and the results agreed well with certified values.     

Sub- and supercritical chiral separation of racemic compounds on columns with stationary phases having different functional groups

Separation of the enantiomers of each of three different racemates, neutral rac-alpha-tetralol, acidic rac-2-phenylpropionic acid, and basic rac-1-phenylethylamine, using subcritical and supercritical fluid chromatography with two different chiral stationary phases, heptakis(2,3,6-tri-O-methyl)-beta-cyclodextrin (Sumichiral OA-7500 column) and tris(3,5-dimethylphenylcarbamate) of amylose (Chiralpak AD-H column), was compared. The elution order of the enantiomers of the three racemates was determined, and the effects of the type of alcohol modifier, column oven temperature, mobile phase composition, flow rate, and pressure were examined. The most appropriate column oven temperature depended on both the type of alcohol modifier and the compound analyzed. Lower alcohol content improved the peak separation of both rac-alpha-tetralol on the Sumichiral OA-7500 column and rac-1-phenylethylamine on the Chiralpak AD-H column, while the same phenomenon was not observed with either rac-alpha-tetralol or rac-2-phenylpropionic acid on the Chiralpak AD-H column. Decreasing outlet pressure improved the peak separation obtained with rac-2-phenylpropionic acid, but had little effect on either rac-alpha-tetralol or rac-1-phenylethylamine.     

Fast supercritical fluid chromatography hydrocarbon group-type separations of diesel fuels using packed and monolithic columns

Two approaches for decreasing diesel hydrocarbon group-type separation times by normal phase supercritical fluid chromatography (SFC) are compared. Short (10-15 cm) columns with small 3 microm diameter packing are compared with monolithic Chromolith bare silica columns under high carbon dioxide flow rates approaching 5 ml min(-1). Elution times are reduced up to 13-fold on a 10 cm Chromolith column and 7-fold on the short packed columns compared with conventional length columns run at typical flow rates. Short packed columns, with their higher surface area and retention characteristics, offer higher resolutions compared with Chromolith columns. Diesel samples are separated into saturates, mono-, di-, tri-, and polyaromatics in as little as 2 min on a 10 cm packed silica column. Diesel group-type results on a 15 cm titania-silica coupled column compare favorably with results from longer columns.     

Retention mechanisms in super/subcritical fluid chromatography on packed columns

Whereas the retention rules of achiral compounds are well defined in high-performance liquid chromatography, on the basis of the nature of the stationary phase, some difficulties appear in super/subcritical fluid chromatography on packed columns. This is mainly due to the supposed effect of volatility on retention behaviours in supercritical fluid chromatography (SFC) and to the nature of carbon dioxide, which is not polar, thus SFC is classified as a normal-phase separation technique. Moreover, additional effects are not well known and described. They are mainly related to density changes of the mobile phase or to adsorption of fluid on the stationary phase causing a modification of its surface. It is admitted that pressure or temperature modifications induce variation in the eluotropic strength of the mobile phase, but effects of flow rate or column length on retention factor changes are more surprising. Nevertheless, the retention behaviour in SFC first depends on the stationary phase nature. Working with polar stationary phases induces normal-phase retention behaviour, whereas using non-polar bonded phases induces reversed-phase retention behaviour. These rules are verified for most carbon dioxide-based mobile phases in common use (CO(2)/MeOH, CO(2)/acetonitrile or CO(2)/EtOH). Moreover, the absence of water in the mobile phase favours the interactions between the compounds and the stationary phase, compared to what occurs in hydro-organic liquids. Other stationary phases such as aromatic phases and polymers display intermediate behaviours. In this paper, all these behaviours are discussed, mainly by using log k-log k plots, which allow a simple comparison of stationary phase properties. Some examples are presented to illustrate these retention properties.     

Capillary electrochromatography using columns packed with a supercritical fluid carrier

Summary Columns for capillary electrochromatography may be prepared by packing reversed phase silica-based material using a supercritical fluid carbon dioxide carrier. Procedures for the in-situ manufacture of frits and UV detection windows, and the wetting of columns are described. The columns were employed in two commercial instruments (and a home-built system), and their properties investigated during the separation of standard mixtures of test compounds. The columns are highly efficient and durable, with reduced plate heights of 1.0–1.4. The repeatability of retention time, peak area and peak height was measured. The influence of applied voltage and column temperature and of electrokinetic injection parameters was explored, along with other practical considerations.     

Analysis of complex samples by solvating gas chromatography (supercritical fluid to gas transition)

The various forms of chromatography are primarily determined by differences in the physical state of the mobile phases. The main chromatographic categories include gas chromatography (GC), liquid chromatography, and supercritical fluid chromatography. Adjusting a temperature and pressure will change the mobile phase from liquid to supercritical fluid to gas, with concomitant changes in their physical properties. In this paper, the technique transition-phase chromatography (TPC) is described. In TPC, different mobile phase conditions exist inside the column. This phase transformation within the column results in huge differences in density, solvating power, viscosity, diffusivity, and, as a consequence, in the chromatographic properties of the mobile phase. TPC experiments using capillary columns packed in our laboratory have shown that when the mobile phase is transformed from supercritical fluid to gas, high column efficiencies can be achieved. The transition from supercritical fluid to gas (also called solvating GC), a particular case of the TPC, is evaluated for the separation of complex real samples (environmental, food, and fuels).     

超临界流体色谱流程设计及其应用

本文设计了多功能超临界流体色谱流程,流程中包括毛细管/微填充柱SFC,GC,计算机控制温度、压力、密度及信号采集、处理,配置有超临界流体萃取池,解决了超临界流体色谱分流口易堵问题。利用该流程,将石腊、DC-200气相色谱固定相、黄油、蜂蜡、救心油、红花油等样品进行超临界流体色谱分离。     

Applications of the Chiralpak AD and Chiralcel OD chiral columns in the enantiomeric separation of several dioxolane compounds by supercritical fluid chromatography

Two chiral columns based on polysaccharide derivatives (Chiralpak AD and Chiralcel OD) have been tested for the chiral separation of several dioxolane compounds, using supercritical fluid chromatography. The compounds studied included ketoconazole and some of its precursors. The effect of the different modifiers and the pressure, on the chromatographic parameters was also evaluated. In general, the alcohol modifiers provided better results than acetonitrile, and all the compounds could be separated with these two columns, but the selection of the column depends on the kind of compound.     

Deactivation of small-diameter fused-silica capillary columns for gas and supercritical fluid chromatography

Summary In order to prevent plugging during deactivation of small diameter (50 m i.d.) capillary columns for gas and supercritical fluid chromatography, various high temperature deactivation methods were employed. Pure hexamethyldisilazane and hexamethyldisiloxane (a substitute for D₄) were dynamically coated on the column, while a film (0.05 m) of OV-101 was statically coated, before high temperature (450°C) treatment. Excellent deactivated columns were obtained, and no significant difference in column activity was observed using any of these three methods.Dedicated to Professor S. R. Lipsky on the occasion of his 60th birthday.     

Applications of On-Line SFE/SFC in Environmental Analysis

Polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and organochlorinated Pesticides (OCPs) on different absorbents were extracted and analyzed by a directly coupled supercritical fluid extraction and supercritical fluid chromatography system (on-line SFE/SFC). The influence of various absorbents as sample matrixes on extraction efficiencies was evaluated. In general, the extraction efficiencies were decreased if a matrix had a larger surface area and a smaller pore size. The recoveries of PAHs and PCBs were decreased in inverse proportion to their molar mass. Recoveries of OCPs containing epoxy functional groups were greater than for OCPs lacking this functional group. In conclusion, online SFE/SFC is a rapid (1-2 h) and high recovery (70%-100%) analytical technique.     

Separation of fatty acid methyl esters by comprehensive two-dimensional supercritical fluid chromatography with packed columns and programming of sampling duration

Fatty acid methyl esters from various fats and oils were separated by comprehensive two-dimensional supercritical fluid chromatography with conventional packed columns and FID detection. The first dimension was a silica gel column and the second dimension was an ODS column. This combination was largely orthogonal for the separation of fatty acid methyl esters. The first dimension separations were primarily based on the number of double bonds while the second dimension separations were based on the chain length. The highly-ordered chromatograms and improved resolution allowed the easy detection and identification of minor components. Although the first dimension separations were performed under isobaric conditions where the peak width increased in proportion to the retention, the programming of the sampling duration allowed us to maintain the optimum re-injection frequency (3–4 times) per peak into the second dimension and so to minimize the total analysis time without deteriorating the resolution.     

Enrichment of tocopherols in wheat germ by directly coupled supercritical fluid extraction with semipreparative supercritical fluid chromatography

Enrichment of tocopherol by coupled supercritical fluid extraction/preparative supercritical fluid chromatography is described. Wheat germ powder is used as the starting material and is subjected to supercritical fluid extraction with carbon dioxide. The extracted oil containing tocopherols is concentrated and trapped on a silica gel column by reducing the pressure of carbon dioxide. The trapped oil is then eluted and separated on a silica gel column of 20 mm i.d. x 20 mm length. The column effluent is fractionated by monitoring UV absorption at 290 nm. With this method, tocopherol content of the wheat germ is enriched 100-fold.