Synthesis and structural characterization of a binuclear zirconium complex of tetraanionic p-tert-butylthiacalix[4]arene bridged by methanol

A zirconium complex with the p-tert-butylthiacalix[4]arene anion was synthesized and its crystal structure was determined by single-crystal X-ray analysis. The complex [Zr(μ₂-CH₃OH)(p-tert-butylthiacalix[4]arene)]₂·9H₂O (1) belongs to the orthorhombic system, space group Pnnm, with a?=?20.436(16), b?=?12.160(8), c?=?20.305(12)?Å, V?=?6774(7)?ų and Z?=?2. In Complex 1 zirconium coordinates to four phenolic anions of the deprotonated p-tert-butylthiacalix[4]arene and is bridged by two methanol molecules; the p-tert-butylthiacalix[4]arene adopts a cone conformation.     

Synthesis and crystal structures of Ag and Hg complexes of bis(N-heterocyclic carbenes) on p-tert-butylcalix[4]arene platform

A series of p-tert-butylcalix[4]arene 1,3-diimidazolium salts were successfully prepared by the alkylation of p-tert-butylcalix[4]arene with dibromoalkanes, and sequential substitution reaction with 1-alkylimidazole. Furthermore, coordination reactions of p-tert-butylcalix[4]arene 1,3-diimidazolium salts with silver oxide and mercury acetate gave novel Ag and Hg complexes of bis(N-heterocyclic carbenes) on p-tert-butylcalix[4]arene platform. The single-crystal structures of four p-tert-butylcalix[4]arene 1,3-diimidazolium salts and three metal complexes were successfully determined by X-ray diffraction. An Ag–Ag argentophilic interaction (Ag–Ag bond length is 3.1599(6) Å) is formed between the two Ag–NHC complexes and a dimetallic coordination mode exists in Hg–NHC complexes.     

FT-IR and FT-Raman study of hydrogen bonding in p-alkylcalix[8]arenes

The FTIR and FT Raman spectra of p-alkylcalix[8]arenes (alkyl = tert-butyl, isononyl) were recorded. Analysis of IR spectra showed that the cyclic cooperative intramolecular hydrogen bond is realized in calix[8]arene. It was found that the strength of the cyclic cooperative intramolecular hydrogen bond in the series of alkyl derivatives of calix[8]arenes depends very little on the replacement of the p-tert-butyl groups by the more bulky isononyl group. From our data follows that the orientation of aromatic fragments in calixarene molecules depends on the type of alkyl substituent.An analysis of the changes in the IR spectra with heating and dissolution shows that the conformation of the “pleated-loop” is retained in p-tert-butylcalix[8]arene. It turned out that the intramolecular hydrogen bond is a “probe” of the conformation of calixarene molecules and IR spectroscopy is a unique method that allows one to follow the slightest nuances of changes in the H-bound system of these supermolecules.     

Extraction and DFT study on the complexation of H3O+ ion with tetrakis(2-ethoxyethoxy)-tetra-p-tert-butylcalix[4]arene

Abstract  

Extraction experiments in the two-phase water/nitrobenzene system and γ-activity measurements were used to determine the stability constant of protonated tetrakis(2-ethoxyethoxy)-tetra-p-tert-butylcalix[4]arene in nitrobenzene saturated with water. Density functional theory (DFT) calculations were applied to derive the most probable structure of the tetrakis(2-ethoxyethoxy)-tetra-p-tert-butylcalix[4]arene·H₃O⁺ complex species.     

Synthesis, Crystal Structure, Photophysical Properties, and DFT Calculations of a Bis(tetrathia-calix[4]arene) Tetracadmium Complex

Abstract  

Thiacalix[4]arenes are a unique family of polydentate ligands that offer a combination of four soft sulfur atoms together with four hard phenol oxygen atoms for binding to metal ions. In this study, the tetranuclear cadmium (II) complex Cd₄^II(tca)₂·1.5CH₂Cl₂ (tca⁴⁻ = tetra-anionic p-tert-butylthiacalix[4]arene) (1) was synthesized by reaction of a deprotonated p-tert-butylthiacalix[4]arene and various Cd^II salts. The structure of 1 was established by single crystal X-ray diffraction analysis. The neutral complex 1 contains a square arrangement of four cadmium (II) ions sandwiched between two tca⁴⁻ ligands that have a ‘cone’ conformation similar to that of the free ligand. The absorption and emission properties of the free ligand H₄tca and complex 1 have been recorded and explained by DFT calculations of the molecular orbitals and electronic transitions between them.     

Direct access to upper rim substituted mono- and diaryloxy calix[4]arenes via bis(spirodienone) route

A seemingly ipso-like nucleophilic substitution of the upper rim of p-tert-butylcalix[4]arene is accomplished by an indirect method involving calix[4]arene derived bis(spirodienone). This method not only provides both mono and 1,3-diaryloxy calixarenes but also enables the synthesis of upper rim monothio substituted calix[4]arenes. A modification of the methodology can be successfully extended for the selective synthesis of mono- and 1,3-diquinone calix[4]arenes having free hydroxyl groups at the lower rim, in fewer steps.     

A combined extraction and DFT study on the complexation of K+ with valinomycin

Abstract  From extraction experiments in the two-phase water–nitrobenzene system and γ-activity measurements, the stability constant of protonated tetraethyl p-tert-butylcalix[4]arene tetraacetate in nitrobenzene saturated with water was determined. By using DFT calculations, the most probable structure of the tetraethyl p-tert-butylcalix[4]arene tetraacetate·H₃O⁺ complex species was derived. Graphical Abstract        

Hard–Soft Receptors, Tetrakis[(N,N-diethylaminocarbonyl)methoxy] thiacalix[4]arene Derivatives with cone and 1,3-alternate Conformation

Direct O-alkylation of p-tert-butyltetrathiacalix[4]arene with N,N-diethylchloroacetamide afforded two conformational isomers (1,3-alternate and cone) of tetrakis[(N,N-diethylaminocarbonyl)methoxy]thiacalix[4]arene and 1,3-disubstituted bis[(N,N-diethylaminocarbonyl)methoxy]thiacalix[4]arene, depending on the base used. The complaxation behaviors of the tetrakis isomers were assessed by ¹H NMR titration experiments. Evidence of 1:2 (homo- and hetero-dinuclear) complexes formation of 1,3-alternate-tetrakis[(N,N-diethylaminocarbonyl)methoxy]thiacalix[4]arene with alkali (K⁺ and Na⁺) or transition (Ag⁺) metal ions was obtained. Interestingly, it was found that the cone-tetrakis[(N,N-diethylaminocarbonyl)methoxy]thiacalix[4]arene required a prior Ag⁺ complexation to form 1:2 heterodinuclear complex. Received in final form: 26 January 2005     

Synthesis and photochemical reaction of cyclic oligomers: Synthesis and photopolymerization of novel C‐methylcalix[4]resorcinarene and p‐alkylcalix[n]arene derivatives containing spiro ortho ether groups

New photoreactive calixarene derivatives containing spiro ortho ester groups (calixarenes 3a–3c ) were synthesized by the reaction of 2‐bromomethyl‐1,4,6‐trioxaspiro[4.4]nonane with 2,8,14,20‐tetramethyl‐4,6,10,12,16,18,22,24‐octakis(carboxymethoxy)calix[4]resorcinarene, 5,11,17,23,29,35‐hexamethyl‐37,38,39,40,41,42‐hexakis(carboxymethoxy)calix[6]arene, and 5,11,17,23,29,35,41,47‐octa‐tert‐butyl‐49,50,51,52, 53,54,55,56‐octakis‐(carboxymethoxy)calix[8]arene, which were prepared by the reaction of C‐methylcalix[4]resorcinarene, p‐methylcalix[6]arene, and p‐tert‐butylcalix[8]arene, respectively. The thermal stability of the obtained calixarene derivatives containing spiro ortho ester groups was examined with thermogravimetric analysis, and it was found that these calixarene derivatives had good thermal stability. The photoinitiated cationic polymerization of spiro ortho ester groups in calixarene derivatives 3a–3c was examined with certain photoacid generators in the film state. Interestingly enough, the reaction of calixarene derivatives did not proceed with only photoirradiation; however, the reaction proceeded smoothly when the photoirradiation was followed by heating. Furthermore, calixarene 3a , composed of a C‐methylcalix[4]resorcinarene structure, showed the highest photochemical reactivity in this reaction system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1293–1302, 2002     

Synthesis of hybrid calix[6]arenes having both methylene and epithio bridging groups

Mono-, tri-, and tetra-thiacalix[6]arene were obtained by acid-catalyzed condensation of the corresponding tetramer and dimer derivatives of p-tert-butylphenol bridged by methylene or sulfur. Replacement of CH₂ by sulfur has significant effect on the properties of calix[6]arene such as the strength of intramolecular hydrogen bonding, inclusion ability toward organic molecules, and conformation properties.     

Tripodal chelating ligand-based sensor for selective determination of Zn(II) in biological and environmental samples

Potassium hydrotris(N-tert-butyl-2-thioimidazolyl)borate [KTt^t-Bu] and potassium hydrotris(3-tert-butyl-5-isopropyl-l-pyrazolyl)borate [KTp^t-Bu,i-Pr] have been synthesized and evaluated as ionophores for preparation of a poly(vinyl chloride) (PVC) membrane sensor for Zn(II) ions. The effect of different plasticizers, viz. benzyl acetate (BA), dioctyl phthalate (DOP), dibutyl phthalate (DBP), tributyl phosphate (TBP), and o-nitrophenyl octyl ether (o-NPOE), and the anion excluders sodium tetraphenylborate (NaTPB), potassium tetrakis(p-chlorophenyl)borate (KTpClPB), and oleic acid (OA) were studied to improve the performance of the membrane sensor. The best performance was obtained from a sensor with a of [KTt^t-Bu] membrane of composition (mg): [KTt^t-Bu] (15), PVC (150), DBP (275), and NaTPB (4). This sensor had a Nernstian response (slope, 29.4 ± 0.2 mV decade of activity) for Zn²⁺ ions over a wide concentration range (1.4 × 10⁻⁷ to 1.0 × 10⁻¹ mol L⁻¹) with a limit of detection of 9.5 × 10⁻⁸ mol L⁻¹. It had a relatively fast response time (12 s) and could be used for 3 months without substantial change of the potential. The membrane sensor had very good selectivity for Zn²⁺ ions over a wide variety of other cations and could be used in a working pH range of 3.5–7.8. The sensor was also found to work satisfactorily in partially non-aqueous media and could be successfully used for estimation of zinc at trace levels in biological and environmental samples. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Solvent extraction of europium trifluoromethanesulfonate into nitrobenzene in the presence of p-tert-butylcalix[6]arene and p-tert-butylcalix[8]arene

From extraction experiments and ??-activity measurements, the extraction constants corresponding to the general equilibrium Eu³⁺(aq) + 3A^?(aq) + L(nb) ? EuL³⁺(nb) + 3A^?(nb) taking part in the two-phase water?Cnitrobenzene system (A^? = CF₃SO₃ ^?; L = p-tert-butylcalix[6]arene, p-tert-butylcalix[8]arene; aq = aqueous phase, nb = nitrobenzene phase) were evaluated. Further, the stability constants of the EuL³⁺ complexes in nitrobenzene saturated with water were calculated for a temperature of 25 °C as log ?? _nb(EuL³⁺) = 6.4 ± 0.1 (L = p-tert-butylcalix[6]arene) and log ?? _nb(EuL³⁺) = 11.3 ± 0.1 (L = p-tert-butylcalix[8]arene).     

Azocalixarenes. 6: Synthesis, complexation, extraction and thermal behaviour of four new azocalix[4]arenes

Four new azocalix[4]arenes {5,11,17,23-tetrakis[(2-hydroxy-5-tert-butylphenylazo)]-25,26,27,28-tetrahydroxycalix[4]arene (1), 5,11,17,23-tetrakis[(2-hydroxy-5-nitro phenylazo)]-25,26,27,28-tetrahydroxycalix[4]arene (2), 5,11,17,23-tetrakis[(2-amino-5-carboxylphenylazo)]-25,26,27,28-tetrahydroxycalix[4]arene (3) and 5,11,17,23-tetrakis[(1-amino-2-hydroxy-4-sulfonicacidnapthylazo)]-25,26,27,28-tetrahydroxycalix[4]arene (4)} have been synthesized from p-tert-butylphenol, p-nitrophenol, p-aminobenzoic acid and 1-amino-2-hydroxy-4-sulphonic acid by diazo coupling reaction with p-aminocalix[4]arene. The resulting ligands (1–4) were treated with three transition metal salts (e.g., CuCl₂·2H₂O, NiCl₂·6H₂O or CoCl₂·6H₂O). Cu(II), Ni(II) and Co(II) complexes of the azocalix[4]arene derivatives were obtained and characterized by UV-vis, IR, ¹H-NMR spectroscopic techniques and elemental analysis. All the complexes have a metal:ligand ratio of 2:1. The Cu(II) and Ni(II) complexes of azocalix[4]arenes are square-planar, while the Co(II) complexes of azocalix[4]arenes are octahedral with water molecules as axial ligands. The solvent extraction of various transition metal cations from the aqueous phase to the organic phase was carried out by using azocalix[4]arenes (1–4). It was found that, azocalix[4]arenes 1, 2 and 3 examined selectivity for transition metal cations such as Ag⁺, Hg⁺ and Hg²⁺. In addition, the thermal stability of metal:azocalix[4]arene complexes were also reported. Dedicated to Prof. Dr. Mustafa Yılmaz on the occasion of his 50th birthday     

Synthesis and in vivo biological activity of large-ringed calixarenes against Mycobacterium tuberculosis

A series of large-ringed calix[6,7,8]arene analogues have been synthesised and their affect against Mycobacterium tuberculosis in vivo established. In general, when p-phenylcalixarenes and tert-butylcalixarenes were not functionalised at the lower rim, low biological activities were observed. However on going from partially to fully lower rim pegylated calixarenes the anti-mycobacterial properties improved. The addition of cyanopropoxy groups at the lower rim gave rise to low activities, whereas the addition of acetate moieties interestingly had pro-TB effects. Two upper rim sulfonated calixarenes showed promising properties. In the course of this work, a high yielding procedure to synthesise p-phenylcalix[7]arene was also established.     

A uranyl ion complex of N‐methyl‐p‐tert‐butyl­dihomo­ammonio­calix­[4]­arene with di­aqua­di­pyridine­lithium as counter‐ion

The title complex, di­aqua­di­pyridine­lithium (N‐methyl‐p‐tert‐butyl­dihomo­ammonio­calix­[4]­arene‐κ⁴O)­dioxouranium(VI) tri­pyridine solvate monohydrate, [Li(C₅H₅N)₂(H₂O)₂][UO₂(C₄₆H₅₈NO₄)]·3C₅H₅N·H₂O, contains an `internal' tetraphenoxide‐coordinated uranyl complex of the macrocycle, in which the protonated N atom is involved in an intramolecular hydrogen bond with the uranyl oxo group located in the cavity. The Li⁺ ion is in a tetrahedral environment and its two water ligands are involved in hydrogen bonds with two phenoxide O atoms, two pyridine mol­ecules and one water mol­ecule. This arrangement is compared with those obtained previously for other homo­aza­calixarenes and also for homo­oxa­calixarenes in the presence of alkali metal hydro­xides.     

Synthesis and Structure of a 1,3-alternate-Thiacalix[4]arene diamide Derivative

A novel receptor possessing two complexation sites and bearing 1,3-alternate conformation based on thiacalix[4]arene, confirmed by single crystal X-ray analysis, was prepared. The tetrathiacalix[4]arene diamide shows strong intramolecular hydrogen bonding. The binding behavior towards K⁺ and halides has been examined by ¹H NMR titration experiments.     

p-tert-Butylcalix[5]arene: a New Synthetic Pathway and Crystal Structure of the N,N-Dimethylformamide Complex

The formation of p-tert-butylcalix[5]arene by the opening ofp-tert-butyldihomooxacalix [4]arene and the addition of a monomer has beenstudied. Various facets, including the effects of bases and the nature ofthe monomer added to the p-tert-butyldihomooxacalix[4]arene, have beeninvestigated. p-tert-Butylcalix[5]arene can be prepared in yields up to30%. The structure of its 1 : 2 complex with DMF has been determinedby X-ray crystallography. Crystals are triclinic, space group P¯1, a =1428.2(3) pm, b = 1837.3(3) pm, c = 1276.1(2) pm, = 108.98(1)°, = 105.02(2)°, = 95.21(1)°, Z = 2, D _c = 1.059 kg m^-3,final R value = 0.087. The macrocycle adopts a cone conformation, one guestenclosed inside the cavity, the other one outside.     

A stability-indicating HPLC method for the determination of 17β-estradiol-3-phosphate in an ophthalmic solution

Summary Thep-tert-butylcalix[n]arenes (n=4,6,7,8) andp-tert-butyldihomooxacalix[4]arene have been separated by reverse phase liquid chromatography. Optimum conditions have been obtained on a Spherisorb ODS1, 5 m C18 column by isocratic ambient elution with acetonitrile-methyltert-butyl ether. Calibration plots have been obtained from purified calixarenes and the reliability of the method is confirmed from test mixtures of calixarenes of known composition.     

Alkali Metal Complexation. Binding Properties of cone and partial-cone Calix[4]arenes Bearing a Mixed (O 2 , O 2 ') Donor Set (O = Phosphine Oxide; O ' = Amide or Ester)

The stability constants of alkali metal complexes obtained from the followingO-substituted calix[4]arenes were determined by UV/Vis spectroscopy inmethanol at 20°C: 5,11,17,23-tetra-tert-butyl-25,27-bis(diethylcarbamoylmethoxy)-26,28-bis(diphenylphosphinoylmethoxy)calix[4]arene(cone-1), 25,27-syn-26,28-anti-5,11,17,23-tetra-tert-butyl-25,27-bis(diethylcarbamoylmethoxy)-26,28-bis(diphenylphosphinoylmethoxy)calix[4]arene (paco-1),5,11,17,23-tetra-tert-butyl-25,27-diethoxycarbonylmethoxy-26,28-bis(diphenylphosphinoylmethoxy)calix[4]arene(cone-2) and25,27-syn-26,28-anti-5,11,17,23-tetra-tert-butyl-25,27-diethoxycarbonylmethoxy-26,28-bis(diphenylphosphinoylmethoxy)calix[4]arene(paco-2). All ligands form 1:1 complexes with alkali metal cations. The amide-containing calixarenes were found to be more efficient for alkali metalcomplexation than those bearing ester substituents. While sodium ions are selectivelycomplexed by the two mixed amide-(phosphine oxide) calixarenes, the twoester-containing isomers cone-2 and paco-2 turned out to be selective towards potassium and rubidium ions, respectively. With allfour ligands the lowest stability constants were found for the lithium andcesium ions.     

Ion-selective electrodes based on p-tert-butyl-homooxacalixarene di(ethyl)amides

The diethyl amides of p-tert-butyldihomooxacalix[4]arene (1), p-tert-butylhexahomotrioxacalix[3]arene (2) and p-tert-butylcalix[4]arene (3) were used as active materials in ion-selective membrane electrodes to check the detection of different kinds of cations (Na⁺, K⁺, Cs⁺, Mg^2 + , Ca^2 + , Mn^2 + , Cu^2 + , Zn^2 + , Cd^2 + , Pb^2 +  and tetramethylammonium cation). The electrode characteristics and selectivity coefficients were determined and compared. Optimisation of the PVC membrane composition was achieved using three different plasticisers (bis(2-ethylhexyl) adipate, o-nitrophenyl octyl ether and bis(2-butylpentyl) adipate). Amide 3 shows selectivity for Na⁺, whereas compounds 1 and 2 exhibit the highest selectivity for Pb^2 +  among all the studied cations. The X-ray crystal structure of dihomooxacalix[4]arene tetra(diethyl)amide (1) was determined, revealing it to be in the cone conformation.