丙烯酸酯类单体在空气中紫外固化的研究

辐射可固化涂层在空气中进行紫外光照射，其固化速率随光引发剂组份的增加开始近似线性增大，到某一点后出现突跃．通过对氧气存在下的聚合机理的研究，认为上述现象与氧气引起的自由基终止以及固化过程中的氧气消耗速率有关．根据文中推导的关系式作出的示意图与实验数据基本吻合．     

紫外光固化聚多氟烷氧丙基甲基硅氧烷的研究

本文报道几种紫外光敏有机硅单体:(γ-甲基丙烯酰氧)丙基甲基二甲氧基硅烷,1,3,5,7-四(γ-甲基丙烯酰氧丙基)四甲基环四硅氧烷和1,3-双(甲基丙烯酰氧甲基)-1,1,3,3-四甲基二硅氧烷的合成,以及它们与αH,αH,ωH-全氟烷氧丙基甲基环四硅氧烷的开环共聚反应,制备了一系列新型光敏聚多氟烷氧丙基甲基硅氧烷.并初步研究了在紫外光辐照下,这类光敏聚多氟烷氧丙基甲基硅氧烷的化学结构对固化速度的影响.     

紫外光固化聚氨酯丙烯酸酯树脂的流变行为

合成了一系列紫外光因化聚氨酯丙烯酸酯聚合物,研究了分子量、原料配比、反应方式、含水量、溶剂等对其流变行为的影响。实验表明,控制剂聚物分子量,干燥原料,以ＨＥＡ先与异氰酸酯反应的加料方式合成的树脂,流动性较好。在此基础上合成了较好流动性和光固化性能的蓖麻油紫外光固化树脂。     

超支化烯丙基聚硅氮烷-巯基化合物体系紫外光固化研究

采用等温差示光量热扫描技术(DPC)研究了超支化烯丙基聚硅氮烷-巯基化合物体系的紫外光固化.对比了超支化聚合物-巯基化合物体系、二官能烯丙基硅氮烷-巯基化合物体系和超支化自聚体系的紫外光固化特性,结果表明超支化-巯基化合物体系可在引发剂浓度低(0.1wt%)、辐照强度低(5mW/cm2)的情况下迅速发生光固化反应;与超支化自聚反应相比固化速率高、双键转化率高;而与低官能-巯基化合物体系相比,由于超支化分子结构的独特性,导致固化速率快,双键转化率偏低.对引发剂浓度、辐照强度和反应温度对固化行为的影响表明,在引发剂浓度不超过0.5wt%和辐照强度不大于30.50mW/cm2时,反应速率分别与引发剂浓度和辐照强度的1/2次方成线性关系.运用带扩散因子的自催化固化动力学模型研究了不同温度下的固化行为,计算出特定条件下的光固化动力学参数,表观总反应级数约为8.76,表观活化能为13.97kJ/mol.     

可紫外光固化的超支化聚硅氧烷合成及固化研究

同线型聚硅氧烷聚合物相比，超支化聚硅氧烷聚合物具有低粘度、高反应活性和良好的相容性等特点，其中以制备超支化的聚硅氧烷基硅氧烷和聚烷氧基硅氧烷为主．对于超支化聚硅氧烷主要是以ABx（X=2～6）（其中A为双键，B为硅氢键）型单体为原料，在氯铂酸或Pt／C的催化下，通过硅氢加成反应一步制备，最终聚合物的端基（B）为硅氢键，而双键则完全反应，此外也可通过含不同数目烷氧基硅烷的水解缩合制备超支化聚硅氧烷．     

基于可分散聚苯胺的紫外光固化防腐涂料的研究

采用酸性磷酸酯作为掺杂剂对本征态聚苯胺(EB)进行掺杂,制备了可在聚氨酯丙烯酸酯中进行纳米分散的导电聚苯胺(ES),其分散粒径分布为60~765 nm之间,进而制备了不含重金属的紫外光固化聚苯胺防腐涂料.随着体系中导电聚苯胺含量从0.5 wt%增大5.0 wt%,粒径从60~100 nm增加到190~765 nm.导电聚苯胺含量增大,导致了ES发生团聚,从而粒径增大,进而降低防腐涂层的致密性.当ES含量为1.0wt%时,粒径在110~180 nm之间,防腐涂层在3.5 wt%的Na Cl水溶液中浸泡2400 h后,其0.1 Hz下的绝对阻抗值(|Z|_(0.1 Hz))仍高于1.0×10~8Ωcm~2,同时45~50μm的防腐涂层在划叉中性盐雾试验中,500 h内没有出现起泡现象,且锈蚀宽度小于1 mm,表现出优异的防腐性能.     

紫外光固化光纤油墨对着色光纤光衰减的影响

紫外光固化油墨;聚丙烯酸酯;着色纤维;紫外光固化光纤油墨对着色光纤光衰减的影响     

腰果酚的紫外光固化机理和固化膜性能

研究了腰果酚在无光引发剂条件下的紫外光固化反应,并用IR、UV、元素分析、GPC等分析手段分析了腰果酚的紫外光固化机理及其固化膜性能。结果表明:在紫外光辐照下,腰果酚通过侧链发生氧化聚合反应,和酚羟基的邻对位失去质子形成的自由基引起的苯环缩合反应,最终形成体型高聚物。腰果酚的紫外光固化膜的常规物理机械性能、抗溶剂性、耐化学介质腐蚀性、热稳定性和抗紫外线性能均优于腰果酚醛缩聚物(PC)涂膜。     

紫外光固化聚氨酯丙烯酸树脂的研究进展

综述了紫外光固化聚氨酯丙烯酸酯树脂的研究,讨论了其合成方法、固化机理以及性能。     

用 GC/MS 研究β-二酮结构树脂紫外光自固化的光解及固化

通过碱催化乙酰丙酮和丙烯酸乙酯的迈克尔加成反应,合成了 4,4 二乙酰庚二酸二乙酯(EDAP),该化合物具有可紫外光自固化的β-二酮结构但无光固化基团,利用气相色谱质谱联用(GC/MS) 研究其光解机理从而推断紫外光自固化树脂的固化机理.结果显示季碳原子上接有两个乙酰基的化学结构在紫外光照下不稳定,容易发生裂解,脱掉乙酰基自由基,由此在无光引发剂下仍可以引发丙烯酸酯类单体和低聚物的自由基光聚合.     

紫外光快速固化的树枝状丙烯酸酯齐聚物的制备和性能

通过乙二胺(EDA)和三羟甲基丙烷三丙烯酸酯(TMPTA),以甲醇为催化剂,在30℃进行6小时Michael加成反应,可制得含多个双键的树枝状丙烯酸酯齐聚物(DAO).与相似分子量的线性丙烯酸酯齐聚物相比,DAO粘度低,用作紫外光固化树脂,其固化速度快,且固化产物硬度好,耐溶剂性好.     

Solvent Effect of DMSO-d6 on 1,2-Diols in 1H NMR

There is a classic experiential rule about 1,2-diol RCR^1 （OH） CR^1 （OH） R（ R^1 = H or methyl）, that is, the proton chemical shift of the α-R^1 group at the hydroxvl group in the all-isomer, in general, aPPears in a higher field with ca.     

巯基硅溶胶对改性亚麻籽油紫外光固化反应活性的影响

用溶胶-凝胶法制备了新型的多功能巯基硅氧烷溶胶;用亚麻籽油和环戊二烯合成了可光聚合的改性亚麻籽油低聚物(NLO),并用红外光谱(FT-IR)表征了其结构。用光-差示扫描热分析(Photo-DSC)和在线红外(RT-IR)对NLO、巯基硅氧烷的紫外光固化体系的光聚合反应活性及可光聚合官能团的转化率进行了动力学研究。结果表明:巯基硅氧烷能大大提高NLO的自由基聚合速率,环烯键对硫醇十分敏感,巯基硅氧烷溶胶兼具光引发剂和交联剂的作用。     

Modeling the Effect of Oxygen on Photopolymerization Kinetics

Summary: A comprehensive one‐dimensional photopolymerization model was utilized to investigate the effect of oxygen on the free‐radical photopolymerization kinetics. The spatial profiling aspect of the model provided insight into the heterogeneity of the cure kinetics due to oxygen inhibition, specifically the variance in the concentration profile of monomer and oxygen. Double bond conversion was negligible for the top ten microns of the film due to continuous oxygen diffusion, and increased with increasing depth. Similarly, the oxygen concentration decreased with increasing depth due to the competition between oxygen diffusion time and the polymerization rate. The effect of initiation rate on the extent of oxygen inhibition was investigated for various oxygen concentrations. As the initiation rate increased, the polymerization rate increased, and eventually approached that of a sample in an inert environment. Similarly, as the oxygen concentration was decreased, the polymerization rate increased. The effect of varying the initiation rate on the cure profile in the oxygen‐exposed film was also studied. It was found that the unpolymerized tacky layer decreased from 50 µm to 5 µm with a 3 order of magnitude increase in initiation rate. Using the pseudo steady state approximation, the relationship between polymerization rate and initiation rate was derived for films in an oxygen environment. A direct relationship between the polymerization and initiation rate was found for films in air. The polymerization model supported this derivation and found that as the oxygen concentration was decreased, the dependence on initiation rate, or alpha, decreased, reaching the accepted value of 0.5 for alpha in inert environments.

Double bond conversion versus film depth and cure time.     

紫外光固化材料热老化黄变的研究

本文通过监测添加不同类型和不同比例的抗氧剂的紫外光固化材料在热老化过程中黄变因数的变化,来考察抗氧剂对紫外光固化材料热老化黄变的影响和不同的抗黄变能力.利用紫外-可见光谱仪表征老化过程试样的透光率,结果表明,抗氧剂能很好地减小紫外光固化材料的热老化黄变,抗氧剂中的羟基的抗黄变能力存在差异,决定了抗氧剂的抗黄变能力.Irgafos-168分别与Ir-ganox-1010和Irganox-1076复配时,表现出较好的协同效应,从而使复配抗氧剂的抗黄变能力比单组分抗氧剂的抗黄变能力强.     

羰基化合物在Si(100)表面[2+2]环加成和α-H裂解反应的选择性

最近研究表明: 丙酮能与半导体Si(100)表面发生[2+2]环加成和α-H 裂解反应形成相应的Si―C键或Si―O键, 在半导体材料的合成方面具有重要意义. 为进一步弄清不同羰基化合物在Si(100)表面的反应机理,本文应用密度泛函理论方法在B3LYP/6-311++G(d,p)//6-31G(d)水平上较为系统地研究了一系列羰基化合物CH₃COR (R=CH₃, H, C₂H₅, C₆H₅)与Si(100)表面的反应. 研究结果表明: 不论是[2+2]环加成反应还是α-H 裂解反应都对应较低的反应势垒(小于25 kJ·mol^-1); 环加成反应的势垒比α-H 裂解反应的势垒略高; 羰基上的取代基对反应势垒的影响较少; α-H裂解反应产物为动力学和热力学控制产物; 对丁酮来说, 1-位和3-位H原子的裂解反应都比较容易, 势垒相差很小. 这些结果表明羰基化合物与Si(100)表面的反应将得到多种产物.     

Effect of Asphaltenes and Resins on Asphaltene Aggregation Inhibition,Rheological Behaviour and Waterflood Oil-Recovery

This study presents an investigation about the influence of resins and asphaltenes, extracted from two Mexican crude oils (light and heavy oil samples), on the asphaltene aggregation inhibition, rheological behavior, and waterflood oil-recovery. Resins and asphaltenes were characterized by means of elemental analysis, metals analysis by atomic absorption, ¹H and ¹³C nuclear magnetic resonance (NMR) spectroscopy, and electrospray ionization mass spectrometry (ESI-MS) in order to evaluate the effect of their structural parameters on the phenomena studied. Efficiency of the resins fraction as natural inhibitors of asphaltene aggregation was evaluated trough ultraviolet–visible (UV–vis) spectroscopy. Results showed better efficiencies of resins on asphaltene aggregation inhibition at resin/asphaltene (R/A) ratios close to unity and at high temperature. In addition, efficiencies were influenced by structural characteristics of the asphaltene–resin system. Rheological behavior of the heavy crude oil sample was significantly influenced by the presence of asphaltenes and resins. Finally, asphaltenes and resins played an important role on wettability and waterflood oil-recovery.     

乙二醇二缩水甘油醚的合成及作为阳离子型紫外光固化稀释剂性能研究

以三氟化硼乙醚络合物为催化剂,以氢氧化钠为成环反应的闭环剂,利用乙二醇和环氧氯丙烷为原料合成了乙二醇二缩水甘油醚.研究了催化剂三氟化硼乙醚络合物用量、环氧氯丙烷和乙二醇摩尔比、氢氧化钠和乙二醇摩尔比,以及成环反应温度这些因素对合成反应的影响.结果表明较好的合成反应条件是:三氟化硼乙醚络合物质量分数为0.40%,环氧氯丙烷和乙二醇较佳摩尔比为2.4:1,氢氧化钠和乙二醇较佳摩尔比为2.2:1,较佳的成环反应温度为30℃.同时,把乙二醇二缩水甘油醚作为稀释剂加入到环氧树脂E-51中,利用三芳基锍鎓六氟锑酸盐作为引发剂,制备了阳离子型紫外光固化涂料,其紫外光固化膜的拉伸强度为46.25MPa,杨氏模量为1487.26MPa,断裂伸长率为6.27%.     

光催化全分解水制氢中助催化剂表面氢氧复合反应的抑制

在光催化全分解水产氢的过程中, Pt等助催化剂在催化产生氢的同时也会诱导催化氢气和氧气重新复合为水的逆反应,严重降低了悬浮体系光催化全分解水产氢的效率.我们综述了近年来在逆反应抑制方面的研究进展,总结和对比分析了各种抑制逆反应策略的特点,并对将这些方法应用于悬浮体系光催化全分解水制氢的前景进行了展望.     

Enhancing UV Photopolymerization by a Red-light Preirradiation: Kinetics and Modeling Strategies for Reduced Oxygen Inhibition

A novel strategy for red-light-controlled oxygen inhibition for improved UV-light-initiated monomer conversion is theoretically presented for the first time. The dual-wavelength kinetic equations are derived, numerically and analytically solved for the oxygen and photoinitiator concentration profiles. The UV-light-initiated Type I conversion efficacy is an increasing function of its concentration (C₂₀) and the light dose at transient state, but it is a decreasing function of the light intensity, scaled by [C₂₀/I₂₀]^0.5, at steady state. In contrast, the red-light-initiated Type II efficacy is mainly dose dependent. Longer red-light preirradiation time (T_P) leads to a shorter UV-light T_ID of UV-light conversion, which is strongly red-light dose dependent, rather than intensity dependent. The numerical new finding is also predicted by the analytic formulas showing that oxygen and monomer conversion are strongly red-light dose dependent in a Type II mechanism. Finally, strategies for controlled initiation–inhibition switch based on two mechanisms, (a) oxygen inhibition for improved conversion and (b) radical inhibition for spatial confirmation in 3D printing, are presented. To conclude, UV-light conversion could be improved by a red-light preirradiation and more importantly and could be customizely tailored by the controlled induction time. UV-light photopolymerization conversion could be improved by a red-light preirradiation and could be customizely tailored by the controlled induction time. The UV-light-initiated Type I conversion efficacy is an increasing function of its concentration and the light dose at transient state, but it is a decreasing function of the light intensity at steady state. In contrast, the red-light-initiated Type II efficacy is mainly dose dependent. Longer red-light preirradiation time leads to a shorter UV light. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 683–691