FFC-1离子交换纤维对酸碱有害气体吸附性能的研究

系统考察了不同直径及反离子形式的FFC-1聚羧酸离子交换纤维对酸碱有害气体的穿透吸附,各种温、湿度条件下的吸水率,以及作为有害气体吸附滤除材料的重复使用与再生性能。研究表明:FFC-1纤维直径的减小有利于提高对有害气体的动态吸附容量。在体系温度、相对湿度分别为15℃、50%时,以3D腈纶为起始原料的钠型FFC-1离子交换纤维的吸水率≥350mg/g.纤维;对SO2的穿透吸附容量可达200mg/g.纤维。FFC-1离子交换纤维具有良好的重复使用与再生能力,经20次再生循环使用后,纤维交换容量未见明显变化。     

亚胺二乙酸基纤维对含镍废水的选择性吸附与再生研究

以自制亚胺二乙酸和羧酸基功能纤维为吸附材料,系统研究了有限浴及柱吸附条件下对Ni~(2+)、Ca~(2+)和Mg~(2+)共存废水的选择性吸附性能。结果表明,与羧酸基纤维相比,亚胺二乙酸纤维具有很好的选择性吸附功能(有限浴条件下k_(Ca)~(Ni)和k_(Mg)~(Ni)分别为4.63和11.33;柱吸附条件下k_(Ca)~(Ni)和k_(Mg)~(Ni)分别为5.26和136.17),且对Ni~(2+)的饱和吸附容量可达100mg/g左右;以2.5mol/L硫酸溶液为洗脱剂,Ni~(2+)回收率≥94%;自制纤维经5次使用与再生循环后,对Ni~(2+)吸附容量基本不变,具有良好的实际应用前景。     

聚对二甲苯纳米纤维阵列的CVD液晶模板法制备及降解性能

聚对二甲苯(PPX)具有优异的生物相容性和化学稳定性, 将其构建成仿细胞外基质结构的可降解纳米纤维在生物工程领域具有重要意义. 本文采用化学气相沉积(CVD)法, 以向列型热致液晶E7为模板, 以4-羟甲基-对二甲苯二聚体(PCP-CH₂OH)为聚-(4-羟甲基-对二甲苯)(PPX-CH₂OH)的前驱体, 通过在其分子链上引入 5,6-苯并-2-亚甲基-1,3-二氧杂环庚烷(BMDO)链段制备BMDO/PPX-CH₂OH共聚物纳米纤维阵列, 探讨了共聚物纳米纤维阵列形貌的影响因素, 分析得到了制备共聚物纳米纤维阵列的最佳反应条件, 并研究了BMDO/PPX-CH₂OH共聚物纳米纤维阵列的生物降解性能. 研究表明, 在液晶模板作用下, 通过CVD法成功地使PCP-CH₂OH与BMDO共聚, 并得到了BMDO/PPX-CH₂OH共聚物纳米纤维阵列; 其形貌主要受样品台的温度和沉积速率的影响, 而单体质量比影响较小; 经优化后CVD最佳条件为: 样品台温度-10 ℃, 沉积速率约为0.01 nm/s, 单体质量比为10∶1; 共聚物在37 ℃的0.1 mol/L Na₂CO₃/0.1 mol/L NaHCO₃的缓冲溶液体系下可有效降解, 当降解时间超过23 d后, 纳米纤维阵列中的酯基可完全分解; 当降解时间超过30 d时, 纳米纤维阵列基本降解完全, 总体呈碎片状.     

新型双功能交联型阴离子交换膜的制备与性能

以2-甲基咪唑为原料合成2种离子液体前驱体1-烯丙基-2-甲基咪唑和1-丁基-2-甲基咪唑,以苯乙烯(St)和对氯甲基苯乙烯(VBC)为原料制备聚离子液体主链p(St-co-VBC),2种离子液体前驱体与聚离子液体主链发生季铵化反应铸膜,制备了交联结构和梳型侧链结构型阴离子交换膜(AEMs).通过傅里叶红外光谱、扫描电子显微镜和热重分析等考察了阴离子交换膜的结构、微观形貌、氢氧根离子传导率、热稳定性及碱性稳定性等性能.结果表明,AEMs含水率为36.7%~93.4%,离子交换容量为1.61~2.16 mmol/g,80℃时,p(St-co-VBC)-3型AEMs氢氧根离子传导率高达68.4 mS/cm,在1 mol/L NaOH溶液中碱性浸泡240 h后,氢氧根离子传导率仍高达52.2 mS/cm,具备良好的碱性稳定性.     

离子交换纤维的性能和应用

本文综述了离子交换纤维(化学吸附纤维)的品种、性能及应用。列出了以聚乙烯醇、聚丙烯腈、聚烯烃为基休的离子交换纤维品种,介绍了这些纤维的化学吸附、化学稳定性、机械强度等性能以及它们在气体、水溶液的净化、提纯和回收、填充床电渗析方面的应用。     

PPS基叔胺离子交换纤维对Cr(Ⅵ)选择性吸附研究

首次报道通过氯甲基化聚苯硫醚纤维的胺化反应制得一种叔胺型离子交换纤维,研究了Cr2O72-和SO42-共存体系中该纤维对Cr(Ⅵ)的选择性吸附性能。结果表明,该离子交换纤维具有很高吸附容量,SO42-的存在并不影响该纤维对Cr(Ⅵ)的选择性吸附。在溶液pH值为2,Cr(Ⅵ)和SO42-浓度分别为65mg/L和480mg/L条件下,OH-型和SO42-型叔胺离子交换纤维对Cr(Ⅵ)的吸附容量分别为308.09mg/g和335.56mg/g。NaOH溶液可将CrO42-有效洗脱,纤维经过5次吸附-再生循环后,其吸附性能基本保持不变。     

吡哌酸、左氧氟沙星及环丙沙星在 0.5mol/L H2SO4中对碳钢的缓蚀性能与机理研究

利用失重实验、动电位极化曲线测试、交流阻抗测试(EIS)及扫描电子显微镜(SEM)方法对吡哌酸(8-乙基-5-氧代-5,8-二氢-2-(1-哌嗪基)吡啶并[2,3-d]嘧啶-6-羧酸)、左氧氟沙星[(±)-9-氟-2,3-二氢-3-甲基-10-(4-甲基-1-哌嗪基)-7-氧代-7H-吡啶并[1,2,3-de][1,4]苯并恶嗪-6-羧酸]及环丙沙星[1-环丙基-6-氟-1,4-二氧-4-氧代-7-(1-哌嗪基)-3-喹啉羧酸]在303 K时0.5 mol/L H2SO4 中对碳钢的缓蚀性能、作用机理进行研究.失重实验得出,303 K 时试样浸泡在0.5 mol/L H2SO4 溶液中的腐蚀速度随缓蚀剂的浓度增大而减小,同时三种缓蚀剂的缓蚀效率显著增大.电化学测试表明缓蚀剂分子对阴阳极反应均有抑制作用,但对阴极的抑制作用更加明显,其抑制作用与缓蚀剂在金属表面的覆盖有关.303 K 时缓蚀剂在金属表面的吸附行为符合 Langmuir 等温线,且作用过程物理、化学吸附兼有.扫描电子显微镜观察结果表明,添加三种缓蚀剂对碳钢表面的腐蚀起到了显著的保护作用.同种条件下的测试结果表明,环丙沙星缓蚀性能最强.     

有机胺对阳离子交换树脂性能的影响

采用浸泡方法分别研究了氨、乙醇胺、吗啉对阳离子交换树脂性能的影响。利用光学显微镜观察浸泡前后阳离子交换树脂的形貌。55℃下,分别在pH值为9.3的氨、乙醇胺及吗啉的溶液中浸泡不同时间后离子交换树脂的总交换容量、含水率、湿视密度、湿真密度变化均不明显。以3种不同浓度(0.9mol/L、1.4mol/L、1.9mol/L)的氨、乙醇胺及吗啉的溶液分别浸泡离子交换树脂,浸泡后总交换容量、含水率、湿视密度、湿真密度的变化也不大。在恒定pH值与不同浓度碱化溶液中浸泡后,黑琥珀色半透明离子交换树脂的颜色均变浅。实验结果表明有机胺对凝胶型阳离子交换树脂的性能和形貌影响不大。     

FFA—1离子交换纤维的物理与化学性能的研究

利用IR谱，热分析及SEM技术对FFA-1离子交换纤维的物理与化学性能进行了表征，测定了它的pH滴定曲线，吸水率，机械强度，对SO2的动态吸附以及气体阻力性能，为这种功能纤维在吸附净化有害气体等方面的实际应用提供了必要的性能参数。     

高性能锂离子电池隔膜的结构设计及其制备与表征

设计并采用高压静电纺丝法制备了单层结构的聚偏氟乙烯(PVDF)/偏氟乙烯与六氟丙烯的共聚物(PVDF-HFP)纳米纤维膜及三层结构、二层结构的PVDF/PVDF-HFP/Al2O3复合纳米纤维膜.复合膜的表面形貌、热物理性质和电化学性能通过扫描电子显微镜(SEM)、示差扫描量热法(DSC)、高温尺寸收缩率、交流阻抗法进行了表征.单层结构的PVDF/PVDF-HFP纳米纤维膜的纤维表面光滑,平均纤维直径2μm,纤维分布较均匀,而PVDF与Al2O3复合后的纤维表面粗糙,平均纤维直径变小,结晶度降低,吸液率增大.二层结构的PVDF/PVDF-HFP/Al2O3复合隔膜在170℃下受热1 h收缩率为3%.将3种结构的复合膜在1 mol/L Li PF6/(EC+DMC+DEC,1∶1∶1,W/W/W)电解质溶液中活化得到聚合物电解质.25℃时,二层结构的PVDF/PVDF-HFP/Al2O3复合隔膜吸液率高达497 wt%,离子电导率可达5.04×10-3S/cm,电化学稳定窗口达到4.62 V(Li/Li+).组装成Li Fe PO4/Li电池测试其电池性能,结果表明,二层结构的PVDF/PVDF-HFP/Al2O3复合膜朝向锂负极时,电池的循环性能更好,且与锂金属负极具有更好的相容性和界面稳定性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.