Nanowear studies in reversibly switchable polystyrene-poly(acrylic acid) mixed brushes

Wear studies were performed on polystyrene (PS)-poly(acrylic acid) (PAA) mixed polymer brushes and corresponding monobrushes in a dried state. The aim was to study the wear mechanism in polymer brush surfaces as well as to investigate the effect of switching of PS + PAA binary brush surfaces (on treatment with the selective solvents for the PS and PAA) on the wear process. Wear experiments were carried out using atomic force microscopy (AFM) under a controlled environment. The wear experiments were performed as a function of scan number using a sharp silicon nitride tip to induce the wear on the sample surfaces. The wear mechanism on different brush surfaces was influenced by molecular entanglement as well as adhesion and friction on the sample surface. The wear process on the PS monobrush surface treated with toluene took place via formation of the ripples. On the other hand, a typical wear mode observed on the PAA monobrushes was removal of the polymeric material from the surface. For the mixed brush surface treated with toluene (selective solvent for PS) where PS chains dominated the top of the sample surface, the typical wear mode observed was ripple formation similar to that observed for the PS monobrushes. However, when a mixed brush was treated with ethanol and pH 10 water so that PAA chains dominated the top layer, wear occurred via removal of material. The amount of wear on the surfaces increased with the number of scans. Furthermore, the load and scan velocity dependence of the wear process was also investigated. Wear on polymer brush surfaces increased on increasing the load and/or decreasing the scan speed. The present study shows that wear can be controlled/tuned using mixed responsive brushes.     

Adhesion between chemically heterogeneous switchable polymeric brushes and an elastomeric adhesive

We investigated the adhesive properties of binary heterogeneous polymer brushes made from end-functionalized polystyrene (PS) and poly(2-vinylpyridine) (P2VP) chains. The molecular organization of the mixed brush could be varied reversibly by exposure to selective solvents for PS (toluene) and for P2VP (acidic water). This exposure results in reversible switching of adhesive and wetting properties. The manner in which the adhesion switching occurs can be tuned by the composition of mixed brushes. However, the outer surface composition could be enriched more effectively in PS after the toluene treatment than in P2VP after the acidic water treatment. As a result, the mixed brush compositions that showed the largest difference in properties between an exposure to toluene and an exposure to water were the P2VP-rich compositions. Adhesive properties, tested against a soft hydrophobic pressure-sensitive adhesive (PSA) using a probe test, always showed smaller differences between solvent treatments than wetting properties with water, suggesting a much higher sensitivity of the hydrophobic/hydrophilic brushes to polar molecules than to nonpolar molecules.     

Nucleating pattern formation in spin-coated polymer blend films with nanoscale surface templates

We use Dip-Pen Nanolithography (DPN) to generate monolayer surface templates for guiding pattern formation in spin-coated polymer blend films. We study template-directed pattern formation in blends of polystyrene/poly(2-vinylpyridine) (PS/P2VP) as well as blends of PS and the semiconducting conjugated polymer poly(3-hexylthiophene) (P3HT). We show that acid-terminated monolayers can be used to template pattern formation in PS/P3HT blends, while hydrophobic monolayers can be used to template pattern formation in PS/P2VP blends. In both blends, the polymer patterns comprise laterally-phase separated regions surrounded by vertically separated bilayers. We hypothesize that the observed patterns are formed by template-induced dewetting of the bottom layer of a polymer bilayer during the spin-coating process. We compare the effects of template feature size and spacing on the resulting polymer patterns with predictions from published models of template-directed dewetting in thin films and find the data in good agreement. For both blends we observe that a minimum feature size is required to nucleate dewetting/phase separation. We find this minimum template diameter to be approximately 180 nm in 50/50 PS/P2VP blends, and approximately 100 nm in 50/50 PS/P3HT blends. For larger template diameters, PS/P2VP blends show evidence for pattern formation beginning at the template boundaries, while PS/P3HT blends rupture randomly across the template features.     

Preparation and characterization of a thermoresponsive gigaporous medium for high-speed protein chromatography

A high-speed thermoresponsive medium was developed by grafting poly(N-isopropylacrylamide-co-butyl methacrylate) (P(NIPAM-co-BMA)) brushes onto gigaporous polystyrene (PS) microspheres via surface-initiated atom transfer radical polymerization (ATRP) technique, which has strong mechanical strength, good chemical stability and high mass transfer rate for biomacromolecules. The gigaporous structure, surface chemical composition, static protein adsorption, and thermoresponsive chromatographic properties of prepared medium (PS–P(NIPAM-co-BMA)) were characterized in detail. Results showed that the PS microspheres were successfully grafted with P(NIPAM-co-BMA) brushes and that the gigaporous structure was robustly maintained. After grafting, the nonspecific adsorption of proteins on PS microspheres was greatly reduced. A column packed with PS–P(NIPAM-co-BMA) exhibited low backpressure and significant thermo-responsibility. By simply changing the column temperature, it was able to separate three model proteins at the mobile phase velocity up to 2167 cm h⁻¹. In conclusion, the thermoresponsive polymer brushes grafted gigaporous PS microspheres prepared by ATRP are very promising in ‘green’ high-speed preparative protein chromatography.     

Changes in thermodynamic interactions at highly immiscible polymer/polymer interfaces due to deuterium labeling

Deuterium labeling has been shown previously to affect thermodynamic interactions at polymer surfaces, polymer/polymer heterogeneous interfaces, and in bulk (away from a surface or interface). However, the changes in polymer-polymer interactions due to deuterium labeling have not been thoroughly investigated for highly immiscible systems. It is shown here that deuterium labeling can influence polymer-polymer interactions at heterogeneous interfaces with highly immiscible systems, namely, polystyrene/poly(2-vinylpyridine) (PS/P2VP), polystyrene/poly(4-vinylpyridine) (PS/P4VP), and polystyrene/poly(methyl methacrylate) (PS/PMMA). Using secondary ion mass spectrometry, segregation of deuterium labeled polystyrene (dPS) in a dPS + unlabeled PS (dPS:hPS) blend layer was observed at the dPS:hPS/hP2VP, dPS:hPS/hP4VP, and dPS:hPS/hPMMA heterogeneous interfaces. However, a reference system involving PS on a PS brush shows no segregation of dPS to the interface.     

Mixed polymer brushes by sequential polymer addition: anchoring layer effect

Smart surfaces can be described as surfaces that have the ability to respond in a controllable fashion to specific environmental stimuli. A heterogeneous (mixed) polymer brush (HPB) can provide a synthetic route to designing smart polymer surfaces. In this research we study HPB comprised of end-grafted polystyrene (PS) and poly(2-vinyl pyridine) (P2VP). The synthesis of the HPB involves the use of an "intermolecular glue" acting as a binding/anchoring interlayer between the polymer brush and the substrate, a silicon wafer. We compare anchoring layers of epoxysilane (GPS), which forms a self-assembled monolayer with epoxy functionality, to poly(glycidyl methacrylate) (PGMA), which forms a macromolecular monolayer with epoxy functionality. The PS and P2VP were deposited onto the wafers in a sequential fashion to chemically graft PS in a first step and subsequently graft P2VP. Rinsing the HPB in selective solvents and observing the change in water contact angle as a function of the HPB composition studied the switching nature of the HPB. Scanning probe microscopy was used to probe the topography and phase imagery of the HPB. The nature of the anchoring layer significantly affected the wettability and morphology of the mixed brushes.     

Area Selective Polymer Brush Deposition

Polymer brush films with chemical functionality to attach to site specific substrate areas are introduced for area selective deposition (ASD) application. It is demonstrated that polymer brushes with chemically defined end sites can be selectively bound to copper‐specific regions of patterned copper/silica (Cu/SiO₂) substrates. The process described overcomes various limitations of currently used technology including cost, complexity, and throughput, with potential implications for future electronic devices and nanomanufacturing. A comparative study of amine‐terminated polystyrene and amine‐terminated poly‐2‐vinyl pyridine polymer brushes (i.e., PS‐NH₂ and P2VP‐NH₂) with similar molecular weights display contrasting behavior on patterned Cu/SiO₂ line features. Further, a thiol terminated poly‐2‐vinyl pyridine polymer brush (i.e., P2VP‐SH) is investigated as a direct spin‐on process to fabricate a metal oxide layer atop Cu areas only. The results presented here detail a novel methodology and open a new exciting process for ASD practices that can facilitate the precise deposition of dense metal, semiconductor, or dielectric films. We also discuss the applicability of polymer brushes to ASD uses going forward.     

Synthesis of basic molecular brushes: ATRP of 4-vinylpyridine in organic media

A poly(2-(2-bromopropionyloxy)ethyl methacrylate) (PBPEM) was used as macroinitiator in the synthesis of molecular brushes with poly(4-vinylpyridine) side chains, (P(BPEM-g-4VP). Atom transfer radical polymerization (ATRP) was employed as the polymerization technique. The polymerizations were carried out in DMF at 30 °C using a copper-chloride-based ATRP catalyst, which converted all the dormant polymer chain ends to alkyl chloride groups, thus minimizing branching and crosslinking, which occurred when a copper bromide-based catalyst was employed. Tris(2-pyridylmethyl)amine was selected as the ligand due to the high activity of its Cu^I complex in ATRP as well as its strong binding to both Cu^I and Cu^II, which prevented competitive complexation of the monomer or polymer to the metal center. In order to prevent crosslinking via radical coupling, the monomer conversion was kept low (under 3%) and the alkyl chloride end groups of P4VP side chains were converted to alkoxyamines upon activation followed by a reaction with TEMPO radical. Dynamic light scattering measurements showed the hydrodynamic diameter (D_H) of the brushes was pH-dependent. Aggregation of single P(BPEM-g-4VP) brushes in water was very pronounced at high pH values but was observed even when the amount of added HCl was enough to completely protonate the pyridine units (D_H = 278 nm).     

Creating surfactant nanoparticles for block copolymer composites through surface chemistry

A simple strategy to tailor the surface of nanoparticles for their specific adsorption to and localization at block copolymer interfaces was explored. Gold nanoparticles coated by a mixture of low molecular weight thiol end-functional polystyrene (PS-SH) (Mn = 1.5 and 3.4 kg/mol) and poly(2-vinylpyridine) homopolymers (P2VP-SH) (Mn = 1.5 and 3.0 kg/mol) were incorporated into a lamellar poly(styrene-b-2-vinylpyridine) diblock copolymer (PS-b-P2VP) (Mn = 196 kg/mol). A library of nanoparticles with varying PS and P2VP surface compositions (FPS) and high polymer ligand areal chain densities was synthesized. The location of the nanoparticles in the PS-b-P2VP block copolymer was determined by transmission electron microscopy. Sharp transitions in particle location from the PS domain to the PS/P2VP interface, and subsequently to the P2VP domain, were observed at FPS = 0.9 and 0.1, respectively. This extremely wide window of FPS values where the polymer-coated gold nanoparticles adsorb to the interface suggests a redistribution of PS and P2VP polymers on the Au surface, inducing the formation of amphiphilic nanoparticles at the PS/P2VP interface. In a second and synthetically more challenging approach, gold nanoparticles were covered with a thiol terminated random copolymer of styrene and 2-vinylpyridine synthesized by RAFT polymerization. Two different random copolymers were considered, where the molecular weight was fixed at 3.5 kg/mol and the relative incorporation of styrene and 2-vinylpyridine repeat units varied (FPS = 0.52 and 0.40). The areal chain density of these random copolymers on Au is unfortunately not high enough to preclude any contact between the P2VP block of the block copolymer and the Au surface. Interestingly, gold nanoparticles coated by the random copolymer with FPS = 0.4 were dispersed in the P2VP domain, while those with FPS = 0.52 were located at the interface. A simple calculation for the adsorption energy to the interface of the nanoparticles with different surface arrangements of PS and P2VP ligands supports evidence for the rearrangement of thiol terminated homopolymers. An upper limit estimate of the adsorption energy of nanoparticles uniformly coated with a random arrangement of PS and P2VP ligands where a 10% surface area was occupied by P2VP -mers or chains was approximately 1 kBT, which indicates that such nanoparticles are unlikely to be segregated along the interface, in contrast to the experimental results for nanoparticles with mixed ligand-coated surfaces.     

Nanowear on polymer films of different architecture

In this paper, we describe atomic force microscope (AFM) friction experiments on different polymers. The aim was to analyze the influence of the physical architecture of the polymer on the degree and mode of wear and on the wear mode. Experiments were carried out with (1) linear polystyrene (PS) and cycloolefinic copolymers of ethylene and norbornene, which are stabilized by entanglements, (2) mechanically stretched PS, (3) polyisoprene-b-polystyrene diblock copolymers, with varying composition, (4) brush polymers consisting of a poly(methyl methacrylate) (PMMA) backbone and PS side chains, (5) PMMA and PS brushes grafted from a silicon wafer, (6) plasma-polymerized PS, and (7) chemically cross-linked polycarbonate. For linear polymers, wear depends critically on the orientation of the chains with respect to the scan direction. With increasing cross-link density, wear was reduced and ripple formation was suppressed. The cross-linking density was the dominating material parameter characterizing wear.     

Nanosensors based on responsive polymer brushes and gold nanoparticle enhanced transmission surface plasmon resonance spectroscopy

Swelling (and shrinking) of poly(2-vinylpyridine), P2VP, polymer brushes, caused by pH changes, could be readily monitored by transmission surface plasmon resonance, T-SPR, spectroscopy. Gold nanoparticles attached to the P2VP polymer brushes dramatically enhanced the pH-induced shift in the T-SPR absorption spectra. (A 50 nm shift of the absorption maximum of the T-SPR spectrum of the supporting gold nanoislands was observed upon changing the pH from 5.0 to 2.0, corresponding to a swelling of the polymer brushes from 8.1 +/- 0.7 to 24.0 +/- 2.0 nm. Same shift in the opposite direction was observed upon changing the pH from 2.0 to 5.0.)     

In-situ investigation of the adsorption of globular model proteins on stimuli-responsive binary polyelectrolyte brushes

Binary brushes constituted from two incompatible polymers can be used in the form of ultrathin polymeric layers as a versatile tool for surface engineering to tune physicochemical surface characteristics such as wettability, surface charge, chemical composition, and morphology and furthermore to create responsive surface properties. Mixed brushes of oppositely charged weak polyelectrolytes represent a special case of responding surfaces that are sensitive to changes in the pH value of the aqueous environment and therefore represent interesting tools for biosurface engineering. The polyelectrolyte brushes used for this study were composed of two oppositely charged polyelelctrolytes poly(2-vinylpyridine) (P2VP) and poly(acrylic acid) (PAA). The in-situ properties and surface characteristics such as as surface charge, surface tension, and extent of swelling of these brush layers are functions of the pH value of the surrounding aqueous solution. To test the behavior of the mixed polylelctrolyte brushes in contact with biosystems, protein adsorption experiments with globular model proteins were performed at different pH values and salt concentrations (confinement of counterions) of the buffer solutions. The influence of the pH value, buffer salt concentration, and isoelectric points (IEP) of the brush and protein on the adsorbed amount and the interfacial tension during protein adsorption as well as the protein adsorption mechanism postulated in reference to recently developed theories of protein adsorption on polyelectrolyte brushes is discussed. In the salted regime, protein adsorption was found to be similar to the often-described adsorption at hydrophobic surfaces. However, in the osmotic regime the balance of electrostatic repulsion and a strong entropic driving force, "counterion release", was found to be the main influence on protein adsorption.     

Use of polystyrene spin-coated compact discs for microimmunoassaying

The analytical potential of polystyrene (PS) spin-coated modified compact discs (CDs) surface as platforms for the development of microarray immunoassays is presented. The surface maintained the optical characteristics of compact discs, obtaining a transparent and smooth film polymer of 70 nm thickness, the track being read (λ 780 nm) without errors in a commercial CD reader/writer. The analytical capability of the methodology was demonstrated through an analysis of a neurotoxic compound (2560 spots per disc), reaching 0.08 μg L⁻¹ as limit of detection. These figures demonstrate the enormous potential of using PS spin-coated compact discs in combination with CD players as an easy-to-operate and portable device to develop lab-on-a-disc analytical applications.     

Temperature-triggered micellization of block copolymers on an ionic liquid surface

In situ neutron reflectivity was used to study thermally induced structural changes of the lamellae-forming polystyrene-block-poly(2-vinylpyridine) (PS-b-P2VP) block copolymer thin films floating on the surface of an ionic liquid (IL). The IL, 1-butyl-3-methylimidazolium trifluoromethanesulfonate, is a nonsolvent for PS and a temperature-tunable solvent for P2VP, and, as such, micellization can be induced at the air-IL interface by changing the temperature. Transmission electron microscopy and scanning force microscopy were used to investigate the resultant morphologies of the micellar films. It was found that highly ordered nanostructures consisting of spherical micelles with a PS core surrounded by a P2VP corona were produced. In addition, bilayer films of PS homopolymer on top of a PS-b-P2VP layer also underwent micellization with increasing temperature but the micellization was strongly dependent on the thickness of the PS and PS-b-P2VP layers.     

Ordering evolution of block copolymer thin films upon solvent-annealing process

Morphologies of polystyrene-block-poly(2-vinylpyridine) copolymer (S2VP) thin films, which are forming poly(2-vinylpyridine) cylinders in bulk phase, were investigated by atomic force microscopy (AFM) and transmission electron microscopy (TEM) to account for their ordering behavior induced by solvent annealing. Initially, when the copolymer was dissolved in toluene, which is selective solvent for majority polystyrene (PS) blocks, and was spin-coated on Si substrates, dimple-type micellar structures of S2VP were formed. After the film was placed in a solvent-annealing chamber covered with a lid under the existence of chloroform, surface morphologies of S2VP were measured as a function of annealing time. In this study, it was found that the morphologies of S2VP thin film repeated the cycle of the creation and extinction of various morphologies on ordering process. Namely, S2VP exhibited the various transformations between different morphologies, including highly disordered state, cylinders normal to the plane, and cylinders parallel to the plane. Each of the morphologies observed here was employed as a template to synthesize gold (Au) nanoparticles or nanowires. The arrays of Au nano-objects were used to tune a surface plasmon resonance.     

Transformation from ordered islands to holes in phase-separating P2VP/PS blend films by adding Triton X-100

Our previous investigation showed that the ordered hexagonal island pattern in the phase-separating polymeric blend films of polystyrene and poly(2-vinylpyridine) (PS/P2VP) formed due to the convection effect by proper control of PS molecular weight, solvent evaporation rate, and the weight ratio of PS to P2VP. In this paper, we further illustrate that, by adding a proper amount of the surfactant Triton X-100 to the PS/P2VP toluene solution, the ordered hexagonal island pattern can be transformed to the ordered honeycomb pattern. The effects of the amount of Triton X-100 on the surface morphology evolution and the pattern transformation are discussed in terms of the collapse of Triton X-100, phase separation between Triton X-100/P2VP and PS, the interfacial interaction between Triton X-100/P2VP and the mica substrate, and the Bénard-Marangoni convection.     

Immobilization of Tris-(8-hydroxyquinoline) aluminum onto P4VP polymer thin films by UV irradiation cross-linking

We report a novel method for the immobilization of Tris-(8-hydroxyquinoline) aluminum (Alq₃) onto poly(4-vinylpyridine) (P4VP) thin polymer films by UV irradiation cross-linking. The polymer films were prepared by spin-coating of P4VP onto cleaned silicon wafer surface followed by UV irradiation. The thicknesses of the polymer thin films were measured by ellipsometry with different irradiation times. The immobilization of Alq₃, orientation and the surface activity were followed using photoluminescence and UV-visible spectroscopy. The surface morphology was investigated by using field emission scanning electron microscopy and atomic force microscopy. Patterning of Alq₃ on P4VP film was obtained using photolithography technique. Our experimental results show that the cross-linked P4VP thin film is a universal surface modifier.     

Adsorption of poly(N-isopropylacrylamide-co-4-vinylpyridine) onto core-shell poly(styrene-co-methylacrylic acid) microspheres

Adsorption of the thermoresponsive copolymer of poly(N-isopropylacrylamide-co-4-vinylpyridine) (PNIPAM-co-P4VP) onto the core-shell microspheres of poly(styrene-co-methylacrylic acid) (PS-co-PMAA) is studied. The core-shell PS-co-PMAA microspheres are synthesized by one-stage soap-free polymerization in water. The copolymer of PNIPAM-co-P4VP is synthesized by free radical polymerization of N-isopropylacrylamide and 4-vinylpyridine in the mixture of DMF and water using K₂S₂O₈ as initiator. Adsorption of PNIPAM-co-P4VP onto the core-shell PS-co-PMAA microspheres results in formation of the composite microspheres of PS/PMAA-P4VP/PNIPAM. The driven force to adsorb the copolymer of P4VP-co-PNIPAM onto the core-shell PS-co-PMAA microspheres is ascribed to hydrogen-bonding and electrostatic affinity between the P4VP and PMAA segments. The resultant composite microspheres of PS/PMAA-P4VP/PNIPAM with surface chains of PNIPAM are thermoresponsive in water and show a cloud-point temperature at about 33 °C.     

Controlled supramolecular assembly of micelle-like gold nanoparticles in PS-b-P2VP diblock copolymers via hydrogen bonding

We report a facile strategy to synthesize amphiphilic gold (Au) nanoparticles functionalized with a multilayer, micelle-like structure consisting of a Au core, an inner hydroxylated polyisoprene (PIOH) layer, and an outer polystyrene shell (PS). Careful control of enthalpic interactions via a systematic variation of structural parameters, such as number of hydroxyl groups per ligand (N(OH)) and styrene repeating units (N(PS)) as well as areal chain density of ligands on the Au-core surface (Σ), enables precise control of the spatial distribution of these nanoparticles. This control was demonstrated in a lamellae-forming poly(styrene-b-2-vinylpyridine) (PS-b-P2VP) diblock copolymer matrix, where the favorable hydrogen-bonding interaction between hydroxyl groups in the PIOH inner shell and P2VP chains in the PS-b-P2VP diblock copolymer matrix, driving the nanoparticles to be segregated in P2VP domains, could be counter balanced by the enthalphic penalty of mixing of the PS outer brush with the P2VP domains. By varying N(OH), N(PS), and Σ, the nanoparticles could be positioned in the PS or P2VP domains or at the PS/P2VP interface. In addition, the effect of additives interfering with the hydrogen-bond formation between hydroxyl groups on Au nanoparticles and P2VP chains in a diblock copolymer matrix was investigated, and an interesting pea-pod-like segregation of Au nanoparticles in PS domains was observed.     

Electroless deposition of nickel on fluoropolymers modified by surface graft copolymerization

Surface modification of Ar plasma-pretreated poly(tetrafluoroethylene) (PTFE) and poly(vinylidene fluoride) (PVDF) films via UV-induced graft copolymerization with 4-vinylpyridine (4VP), 2-vinylpyridine (2VP) or 1-vinylimidazole (VIDz) was carried out. Electroless deposition of nickel could be carried out on these graft-modified fluoropolymer surfaces after PdCl₂ activation. The surface compositions of the graft-modified films were studied by X-ray photoelectron spectroscopy. The adhesion strength between the surface graft-copolymerized fluoropolymer film and the electrolessly deposited nickel was affected by the type of monomers used for graft copolymerization and the graft concentration. The optimum T-peel adhesion strengths of the electrolessly deposited Ni on the 4VP graft-copolymerized PTFE and PVDF surfaces were about 7 and 13 N/cm, respectively. The metal/fluoropolymer assemblies delaminated by cohesive failure inside the fluoropolymer substrates. The enhanced adhesion between the electrolessly deposited Ni and the surface-modified fluoropolymers is attributable to the interfacial charge transfer interactions between the grafted polymer chains and the deposited metals (Pd and Ni), the spatial distribution of the graft chains into the metal matrix and the covalent tethering of the graft chains on the fluoropolymer surface.