Stepwise dansyl grafting on the kaolinite interlayer surface

A block copolymer (PS-b-poly(l-Glu)) composed of polystyrene and poly(l-glutamic acid) was used as a stabilizer for dispersion polymerization of styrene. When dispersion polymerization of styrene was conducted at 70 °C in 80% dimethylformamide-water with 0.5 wt% PS-b-poly(l-Glu), spherical polystyrene particles with D_n = 0.72 μm and narrow size distribution were obtained. Whereas AIBN concentration did not have any effects on particle size, molecular weight of the polystyrene particles was strongly dependent on the initiator concentration. As concentration of the PS-b-poly(l-Glu) increased from 0.2 to 1.0 wt%, particle size decreased from D_n = 0.91 to 0.69 μm with keeping surface area occupied by one poly(l-glutamic acid) chain about S = 50 nm². On the other hand, an increase in initial concentration of styrene from 2 to 20 wt% caused an increase in particle size from D_n = 0.48 to 1.36 μm and a decrease in surface area per poly(l-glutamic acid) block from S = 91 to 45 nm². Colloidal stability of the polystyrene particles in aqueous solution was responsive to pH due to the surface-grafted poly(l-glutamic acid). For dispersion polymerization of styrene, the PS-b-poly(l-Glu) functions as both a stabilizer and a surface modifier.     

Stable free radical polymerization of n-butyl acrylate in the presence of high-temperature initiators

Living radical polymerizations of acrylate are known to be difficult to achieve using TEMPO as a mediator. The stable free radical polymerization (SFRP) of acrylate tends to stop at low monomer conversion due to the accumulation of TEMPO in the medium as a result of unavoidable bimolecular termination. Rather than solving this problem by destroying the excess nitroxide using ascorbic acid or glyceraldehyde associated with pyridine as reported recently, high temperature initiators were used to slowly and continuously generate new radicals throughout the polymerization to consume the excess TEMPO molecules. Polymerizations of n-butyl acrylate initiated by the alkoxyamine unimer (1-benzoyloxy)-2-phenyl-2-(2′,2′,6′,6′-tetramethyl-1′-piperidinyloxy)ethane (BST) were performed between 130 °C and 134 °C in the presence of a series of high temperature peroxide and azo initiators. The best results in this study were obtained by the continuous addition of small amounts of di-tert-amyl peroxide throughout the polymerization. Under these conditions, the acrylate polymerizations fulfilled the criteria of a controlled polymerization process although the molecular weight distributions were slightly broad (M_w/M_n ∼ 1.5).     

Atom transfer radical polymerization of 2-methoxy ethyl acrylate and its block copolymerization with acrylonitrile

2-Methoxy ethyl acrylate (MEA), a functional monomer was homopolymerized using atom transfer radical polymerization (ATRP) technique with methyl 2-bromopropionate (MBP) as initiator and CuBr/N,N,N′,N′,N″-pentamethyldiethylenetriamine (PMDETA) as catalyst system; polymerization was conducted in bulk at 60 °C and livingness was established by chain extension reaction. The kinetics as well as molecular weight distribution data indicated towards the controlled nature of polymerization. The initiator efficiency and the effect of initiator concentration on the rate of polymerization were investigated. The polymerization remained well-controlled even at low catalyst concentration of 10% relative to initiator. The influence of different solvents, viz. ethylene carbonate and toluene on the polymerization was investigated. End-group analysis for the determination of high degree of functionality of PMEA was determined with the help of ¹³C{¹H} NMR spectra. Chain extension experiment was conducted with PMEA macroinitiator for ATRP of acrylonitrile (AN) in ethylene carbonate at 70 °C using CuCl/bpy as catalyst system. The composition of individual blocks in PMEA-b-PAN copolymers was determined using ¹H NMR spectra.     

Synthesis and crystallization behaviors of poly(styrene-b-isoprene-b-ε-caprolactone) triblock copolymers

The triblock copolymers, poly(styrene-b-isoprene-b-ε-caprolactone)s (PS-b-PI-b-PCL) have been synthesized successfully by combination of anionic polymerization and ring-opening polymerization. Diblock copolymer capped with hydroxyl group, PS-b-PI-OH was synthesized by sequential anionic polymerization of styrene and isoprene and following end-capping reaction of EO, and then it was used as macro initiator in the ring-opening polymerization of CL. The results of DSC and WAXD show big effect of amorphous PS-b-PI on the thermal behaviors of PCL block in the triblock copolymers and the lower degree of crystalline in the triblock copolymer with higher molecular weight of PS-b-PI was observed. The real-time observation on the polarized optical microscopy shows the spherulite growth rates of PCL₂₇, PCL₃₂₈ and PS-b-PI-b-PCL₃₄₄ are 0.71, 0.46 and 0.07 μm s⁻¹, respectively. The atomic force microscopy (AFM) images of the PS₉₀-b-PI₆₆-b-PCL₂₈ show the columns morphology formed by it’s self-assembling.     

Aggregation phenomena of linear and miktoarm star copolymers of styrene and dimethylsiloxane: Influence of the architecture

The micellar behavior of PS-b-PDMS, PS-b-PDMS-b-PS linear block and (PS)₂(PDMS) miktoarm star copolymers of polystyrene (PS) and polydimethylsiloxane (PDMS) is investigated in DMF, a selective solvent for PS. The linear PS-b-PDMS and star (PS)₂(PDMS) copolymers exhibit different macromolecular architectures but similar compositions and total molecular weight, while the linear PS-b-PDMS-b-PS copolymer has the same composition as the diblock and miktoarm star but double their molecular weight. Static, dynamic light scattering and viscometry were used for the structural characterization of the micelles. Aggregation numbers were found to increase in the order PS-b-PDMS-b-PS < (PS)₂(PDMS) < PS-b-PDMS. The corona thickness was dependent on the molecular weight of the soluble PS chains. In the case of (PS)₂(PDMS), although the core area per PS chain, A_C, was significantly lower than that of the linear copolymers, the coronal chains were not significantly stretched. This can be attributed to the stiff nature of the PS chains, which maintains the elongated form of the chains.     

Synthesis of poly(vinyl acetate)-b-poly(dimethylsiloxane)-b-poly(vinyl acetate) triblock copolymers by iodine transfer polymerization

Iodine transfer polymerization of vinyl acetate in bulk, initiated by α,α′-azobisisobutyronitrile at 80 °C, has been successfully performed in the presence of an α,ω-diiodo-poly(dimethylsiloxane) macrotransfer agent. The formation of a triblock copolymer PVAc-b-PDMS-b-PVAc has been proved by ¹H NMR and size exclusion chromatography analyses. The analysis of the chain-ends has been performed using ¹H NMR. It was found that a large amount of inverse chain-ends is present at the end of the polymerization. Moreover, the formation of several other side products by degradation of the functional chain-ends has been evidenced.     

Preparation and properties of high performance bismaleimide resins based on 1,3,4-oxadiazole-containing monomers

In research towards high performance polymeric materials, two novel series of bismaleimide (BMI) resins based on 1,3,4-oxadiazole-containing monomers have been designed and prepared by the copolymeriziation reaction of 5-tert-butyl-1,3-bis[5-(4-maleimidophenyl)-1,3,4-oxadiazole-2-yl]benzene (Buoxd) or 4,4′-bis[5-(4-maleimidophenyl)-1,3,4-oxadiazole-2-yl]diphenyldimethylsilane (Sioxd) and 4,4′-bismaleimidodiphenylmethane (BMDM) in different feed ratios. The structures, thermal and dynamic mechanical properties of all the resulting BMI resins were carefully characterized by a combination of methods such as IR, DSC, TGA and DMA. Investigation of the copolymerization process has shown that with an increase of the weight ratio of Buoxd or Sioxd, melting transition temperature (T_m) of BMI monomer mixtures decreased and the exothermic polymerization temperature (T_p) increased. For all BMI monomer mixtures, a rapid polymerization process was observed in the early stage, as shown by the IR investigations. No glass transition was observed for the resulting BMI resins in the temperature range from 50 °C to 350 °C, indicating the formation of highly cross-linking networks. The initial thermal decomposition temperatures (T_d) of the BMI resins were in the range of 477-493 °C in nitrogen and 442-463 °C in the air. Dynamic mechanical analysis (DMA) of the composites made of the BMI resins and glass cloth showed high bending modulus not only at room temperature (E′, 1.9-5.3 GPa) but also at high temperature, e.g., 400 °C (E′, 1.7-4.4 GPa).     

Surface structure of thin asymmetric PS-b-PMMA diblock copolymers investigated by atomic force microscopy

Asymmetric poly(styrene-b-methyl methacrylate) (PS-b-PMMA) diblock copolymers of molecular weight M_n = 29,700 g mol⁻¹ (M_PS = 9300 g mol⁻¹M_PMMA = 20,100 g mol⁻¹, PD = 1.15, χ_PS = 0.323, χ_PMMA = 0.677) and M_n = 63,900 g mol⁻¹ (M_PS = 50,500 g mol⁻¹, M_PMMA = 13,400 g mol⁻¹, PD = 1.18, χ_PS = 0.790, χ_PMMA = 0.210) were prepared via reversible addition-fragmentation chain transfer (RAFT) polymerization. Atomic force microscopy (AFM) was used to investigate the surface structure of thin films, prepared by spin-coating the diblock copolymers on a silicon substrate. We show that the nanostructure of the diblock copolymer depends on the molecular weight and volume fraction of the diblock copolymers. We observed a perpendicular lamellar structure for the high molar mass sample and a hexagonal-packed cylindrical patterning for the lower molar mass one. Small-angle X-ray scattering investigation of these samples without annealing did not reveal any ordered structure. Annealing of PS-b-PMMA samples at 160 °C for 24 h led to a change in surface structure.     

Synthesis and characterization of some novel aromatic polyimides

Three new diamines 1,2-di(p-aminophenyloxy)ethylene, 2-(4-aminophenoxy)methyl-5-aminobenzimidazole and 4,4-(aminopheyloxy) phenyl-4-aminobenzamide were synthesized and polymerized with 3,3′,4,4′-benzophenone tetracarboxylic acid dianhydride (BP), 4,4′-(hexafluoroisopropyledene)diphthalic anhydride (HF) and 3,4,9,10-perylene tetracarboxylic acid dianhydride (PD) either by one step solution polymerization reaction or by two step procedure. The later includes ring opening poly-addition to give poly(amic acid), followed by cyclodehydration to polyimides with the inherent viscosities 0.62-0.97 dl/g. Majority of polymers are found to be soluble in most of the organic solvents such as DMSO, DMF, DMAc, m-cresol even at room temperature and few becomes soluble on heating. The degradation temperature of the resultant polymers falls in the ranges from 240 °C to 550 °C in nitrogen (with only 10% weight loss). Specific heat capacity at 300 °C ranges from 1.1899 to 5.2541 J g⁻¹ k⁻¹. The maximum degradation temperature ranges from 250 to 620 °C. T_g values of the polyimides ranged from 168 to 254 °C.     

A versatile synthesis of poly(lauryl acrylate) using N-(n-octyl)-2-pyridylmethanimine in copper mediated living radical polymerization

A facile synthesis of poly(lauryl acrylate) has been achieved by atom transfer radical polymerization using benzyl-2-bromoisobutyrate, copper (I) bromide, and N-(n-octyl)-2-pyridylmethanimine (OPMI). The latter was of great interest as its synthesis was very easy to carry out and as it allowed the reaction mixture to be homogeneous, which was essential for the control of the reaction. The polymerization was controlled under these conditions and was optimized with the addition of copper (II) bromide as deactivator. We proved that the synthesis of poly(lauryl acrylates) with well defined molecular weights and narrow polydispersities was possible using a ligand which does not require difficult synthesis and purification. We also showed the ability of pyridylmethanimine ligands to control ATRP of an acrylate derivative. Best results were obtained at 130 °C in xylene for [Initiator]₀/[Cu(I)Br]₀/[Cu(II)Br₂]₀/[OPMI]/[lauryl acrylate] equal to 1/1/0.05/2.2/181, respectively (M_n = 19,942, DPI = 1.28).     

Some aspects of nitroxide-mediated living radical polymerization of N-(p-vinylbenzyl)phthalimide

The free radical polymerization of N-(p-vinylbenzyl)phthalimide (VBP) “initiated” with the adduct of 2-benzoyloxy-1-phenylethyl and TEMPO (BS-TEMPO) or TEMPO-terminated polystyrene (PS-TEMPO) in N,N-dimethylformamide (DMF) at 125 °C was found to proceed in a living fashion, providing low-polydispersity PVBP and block copolymers of the type PS-b-PVBA, where TEMPO is 2,2,6,6-tetramethylpiperidinyl-1-oxy. Unlike TEMPO-mediated styrene polymerization, the polymerization rate slightly but distinctly depended on the adduct concentration, which was interpretable as a pre-stationary behavior. The hydrolysis of those polymers gave poly(p-aminomethylstyrene) (PAMS) and PS-b-PAMS, and further treatment of the block copolymer with hydrogen chloride provided an amphiphilic block copolymer. The polymeric amphiphile was used as an emulsifier in emulsion polymerization to produce a positively charged polymeric microsphere.     

Emulsifier-free latex of fluorinated acrylate copolymer

Emulsifier-free latices of fluorinated acrylate copolymers were prepared by semicontinuous polymerization method, with perfluoroalkylethyl methacrylate (Zonyl TM) as a fluoromonomer. Ultrasonic at 40 kHz was adopted to help monomers disperse well in water. The relationships of polymerization conditions between the final conversion and polymerization stability were discussed in detail and the optimal polymerization condition was given. A fluorinated acrylate copolymer was finally obtained and its T_g was 54 °C. The average particle size of the latex was about 601 nm and the particle size distribution of the latex was narrow. The latex film exhibited a low surface free energy and good surface property. By using 6% Zonyl TM, the water contact angle of the film-air interface increased significantly and reached to 110.2°. Compared with the latex film of fluorine-free polyacrylate prepared under the similar polymerization condition, the fluorinated latex film had a better water-resistance and thermal stability.     

Synthesis and characterization of the mixed ligand coordination polymer CPO-5

The synthesis and crystal structures of a novel coordination polymer and its high-temperature variant are described. The as-synthesized material (CPO-5-as), of composition Zn(4,4′-bipyridine)(4,4′-biphenyldicarboxylate)·3H₂O, crystallizes in the triclinic space group P-1 (No. 2) with a=11.0197(2), b=14.2975(3), c=7.6586(1) Å, α=95.9760(9)°, β=108.026(1)°, γ=91.373(1)° and V=1139.16(4) Å³. CPO-5-as is composed of tetrahedral zinc centers that are connected by the organic linkers to give five independent, interpenetrating diamond networks. In the structure, there is additional space for channels that are filled with three water molecules. These water molecules can be removed, leading to an anhydrous variant at 130^oC. CPO-5-130, of composition Zn(4,4′-bipyridine)(4,4′-biphenyldicarboxylate), crystallizes in the triclinic space group P-1 (No. 2) with a=11.1844(6), b=14.0497(7), c=7.7198(3) Å, α=96.917(2)°, β=109.527(2)°, γ=89.115(3)° and V=1134.6(1) Å³. The structure of the five interpenetrating networks is virtually unchanged after the dehydration resulting in CPO-5-130 being a porous structure with an estimated free volume of 19.8%.     

X-ray diffraction study on the thermal expansion behavior of cellulose Iβ and its high-temperature phase

Oriented films of cellulose prepared from algal cellulose were hydrothermally treated to convert them into highly crystalline cellulose Iβ. The lateral thermal expansion behavior of the prepared cellulose Iβ films was investigated using X-ray diffraction at temperatures from 20 to 300 °C. Cellulose Iβ was transformed into the high-temperature phase when the temperature was above 230 °C, allowing the lateral thermal expansion coefficient of cellulose Iβ and its high-temperature phase to be measured. For cellulose Iβ, the thermal expansion coefficients (TECs) of the a- and b-axes were α_a = 9.8 × 10⁻⁵ °C⁻¹ and α_b = 1.2 × 10⁻⁵ °C⁻¹, respectively. This anisotropic thermal expansion behavior in the lateral direction is ascribed to the crystal structure and to the hydrogen-bonding system of cellulose Iβ. For the high-temperature phase, the anisotropy was more conspicuous, and the TECs of the a- and b-axes were α_a = 19.8 × 10⁻⁵ °C⁻¹ and α_b = −1.6 × 10⁻⁵ °C⁻¹, respectively. Synchrotron X-ray fiber diffraction diagrams of the high-temperature phase were also recorded at 250 °C. The cellulose high-temperature phase is composed of a two-chain monoclinic unit cell, a = 0.819 nm, b = 0.818 nm, c (fiber repeat) = 1.037 nm, and γ = 96.4°, with space group = P2₁. The volume of this cell is 4.6% larger than that of cellulose Iβ at 30 °C.     

Methoxy poly(ethylene glycol)-b-poly(valerolactone) diblock polymeric micelles for enhanced encapsulation and protection of camptothecin

Amphiphilic block copolymers, methoxy poly(ethylene glycol)-b-poly(valerolactone) (mPEG-b-PVL), were synthesized via ring opening polymerization of δ-valerolactone in the presence of methoxy poly(ethylene glycol) (mPEG). The copolymers form micelle-like nanoparticles by their amphiphilic characteristics and their structures were examined by Nuclear Magnetic Resonance (NMR). The sizes of nanoparticles ranged from 60 to 120 nm as measured by dynamic light scattering detection, and were larger with higher molecular weight of the copolymers. The Critical Micelle Concentration (CMC) of these nanoparticles in water decreased with increasing molecular weight of hydrophobic segment. Stability analysis showed that the micellar solutions maintain their sizes at 37 °C for six weeks without aggregation or dissociation. The lyophilization method was better than the evaporation method when camptothecin (CPT) was incorporated to the micelles. The former method yielded higher CPT loading efficiency and lower aggregation. The loading efficiency of CPT could be more than 96% and a steady release rate of CPT was kept for twenty six days. Moreover, the mPEG-b-PVL polymeric micelles offered good protection of CPT lactone form at 37 °C for sixteen days. The copolymers showed no cytotoxicity towards L929 mouse muscular cells when incubated for one day. Taken together, the mPEG-b-PVL copolymer has potential to be used for the delivery of CPT or other similar drugs.     

Palladium-catalyzed Heck reaction under thermomorphic mode

Complex PdCl₂(4,4′-bis-(n-C₁₀F₂₁CH₂OCH₂)-2,2′-bpy) (2b) was known to be a good recoverable catalyst under fluorous biphasic system. Complex 2b and PdCl₂(4,4′-bis-(n-C₁₁F₂₃CH₂OCH₂)-2,2′-bpy) (2c), soluble in polar organic solvents at >120 °C but insoluble at 25 °C, were demonstrated here as catalysts in the Pd-catalyzed Heck reaction under the thermomorphic mode and recovered for reusage, that is, the Heck reaction is homogeneously carried out at ca 140 °C, and after reaction the product mixtures remain in solution with the catalyst heterogeneously separated at room temperature.     

Titanium and zirconium complexes containing sterically hindered hydrotris(pyrazolyl)borate ligands: synthesis, structural characterization, and ethylene polymerization studies

The synthesis, characterization and ethylene polymerization behavior of a set of Tp^′MCl₃ complexes (4, M=Ti, Tp^′=HB(3-neopentyl-pyrazolyl)₃⁻(Tp^Np); 5, M=Ti, Tp^′=HB(3-tert-butyl-pyrazolyl)₃⁻(Tp^tBu); 6, M = Ti, Tp^′=HB(3-phenyl-pyrazolyl)₃⁻(Tp^Ph); 7, M=Zr, Tp^′=HB(3-phenyl-pyrazolyl)₃⁻(Tp^Ph); 8, M=Zr, Tp^′ = HB(3-tert-butyl-pyrazolyl)₃⁻(Tp^tBu)) is described. Treatment of these tris(pyrazolyl)borate Group IV compounds with methylalumoxane (MAO) generates active catalysts for ethylene polymerization. For the polymerization reactions performed in toluene at 60 °C and 3 atm of ethylene pressure, the activities varied between 1.3 and 5.1 × 10³ g of PE/mol[M] · h. The highest activity is reached using more sterically open catalyst precursor 4. The viscosity-average molecular weights () of the PE’s produced with these catalyst precursors varying from 3.57 to 20.23 × 10⁵ g mol⁻¹ with melting temperatures in the range of 127-134 °C. Further polymerization studies employing 7 varying Al/Zr molar ratio and temperature of polymerization showed that the activity as well as the polymer properties are dependent on these parameters. In that case, higher activity was attained at 60 °C. The viscosity-average molecular weights of the polyethylene’s decreases with increasing Al/Zr molar ratio.     

A novel strategy for synthesis of amphiphilic π-shaped copolymers by RAFT polymerization

The amphiphilic π-shaped copolymers with narrow molecular weight distribution (M_w/M_n = 1.04-1.09) based on polystyrene (PSt) and poly(ethylene glycol) have been synthesized successfully. The reversible addition-fragmentation transfer (RAFT) polymerization of St in the presence of dibenzyl trithiocarbonate and N,N′-azobis(isobutyronitrile) (AIBN) yielded macro RAFT agent PSt-SC(S)S-PSt, subsequent reaction with excess maleic anhydride (MAh) at 80 °C in tetrahydrofuran afforded the PSt-MAh-SC(S)S-MAh-PSt. It was used as RAFT agent in the RAFT polymerization of St, and finally the amphiphilic π-shaped copolymers were obtained by the reaction of MAh with hydroxyl-terminated poly(ethylene glycol methyl ether) at 90 °C for 48 h. Their structures were confirmed by FT-IR and ¹H NMR spectra, and their molecular weight and molecular weight distribution were measured by gel permeation chromatography.     

Study on controlled/living free-radical polymerization of methyl acrylate in the presence of benzyl 9H-carbazole-9-carbodithioate under thermal condition

The polymerizations of methyl acrylate have been studied under thermal condition using benzyl 9H-carbazole-9-carbodithioate (BCCDT) as control agent. The obtained polymers were characterized by gel permeation chromatography (GPC), ¹H nuclear magnetic resonance (¹H NMR) and MALDI-TOF mass spectra. The results at 60 °C show that the molecular weight of the polymer increases linearly with monomer conversion, the molecular weight distribution is fairly narrow (even inferior to 1.10), and there exists a linear relationship between ln ([M]₀/[M]) and polymerization time. It is worthy of being noticed that the narrow polydispersities are comparable with those from living anionic polymerization. All of the evidences indicate that the polymerization is a good ‘living’ process. When the experiment is carried out at higher temperature, the polymerization rate is markedly faster with controlled polymerization characters except for a relatively broader polydispersity. The good control for free radical polymerization may be correlated with the large conjugation structure of carbazyl of BCCDT.     

N,N′-Diaminoethane linked bis-TEMPO-mediated free radical polymerization of styrene

The N,N′-diaminoethane linked bis-TEMPO nitroxide (C2)-mediated free radical polymerization of styrene at 135 °C in bulk was studied. It was found that under comparable conditions a single nitroxide group of C2 biradical retards the polymerization more than TEMPO. The results were discussed in terms of through-space interactions between two TEMPO moieties of C2 biradical and diffusion effects. According to experimental results analyzed by means of statistical methods, the polymerization system displays a bimodal molecular-weight distribution (MWD) from the beginning of the polymerization process, most probably by undergoing decomposition side reactions leading to irreversible polymer arm (P) separation from PC2P to PC2 and PC2H alkoxyamines. The scale of the decomposition depends rather on the time the system is maintained at the polymerization temperature than on conversion of monomer. Generally, the contribution of low molecular weight chains to overall MWD increases with time of polymerization whereas the contribution of high molecular weight chains to MWD increases for less controlled polymerization systems. For polymers obtained at high [dinitroxide]/[initiator] ratio, the thermal treatment of polystyrene in mass at 135 °C unexpectedly revealed an increase of M_n, which can probably be ascribed to post-polymerization effects involving polystyrene with unsaturated chains end groups.