Temperature- and pH-sensitive interpenetrating polymer networks grafted on PP: Cross-linking irradiation dose as a critical variable for the performance as vancomycin-eluting systems

This work focuses on the effect of gamma-ray radiation conditions on the stimuli-responsiveness and drug-eluting performance of polypropylene (PP) substrates grafted with interpenetrating networks of N-isopropylacrylamide (NIPAAm) and acrylic acid (AAc). PNIPAAm was cross-linked applying 10–100 kGy doses in the presence and absence of the chemical cross-linker N,N′-methylenebisacrylamide (MBAAm). Then, the net-PP-g-PNIPAAm was interpenetrated with PAAc synthesized under a 2.5 kGy dose to obtain net-PP-g-PNIPAAm-inter-net-PAAc films. The amount of grafted PNIPAAm (80%, 125% and 145% levels) and the cross-linking radiation dose (10, 40 and 70 kGy levels) strongly determine the interpenetration of PAAc, the swelling degree, the amount of vancomycin loaded and its release rate. The chemical cross-linker only caused a minor decrease in the degree of swelling. The higher the PNIPAAm grafted on PP and the lower the cross-linking radiation dose, the more the PAAc in the IPN and, consequently, the higher the vancomycin loaded through specific interactions and the more sustained the release (>8 h). The films possessing these features exhibited vancomycin release rate per surface unit suitable to prevent bacterial growth. Thus, adequate tuning of the radiation doses during grafting and cross-linking of the PNIPAAm networks may enable to achieve surface-modified materials for medical devices with an antibiofilm performance.     

Novel comb-type hydrogels of net-[PP-g-AAc]-g-4VP synthesized by gamma radiation,with possible application on Cu2+ immobilization

A novel comb-type grafted hydrogel system of net-[PP-g-AAc]-g-4VP was synthesized by gamma radiation in three steps. In the first step a pH sensitive graft copolymer of AAc onto PP film was obtained by radiation grafting of acrylic acid (AAc) onto polypropylene (PP) films in aqueous solution at radiation doses of 10 kGy with a ⁶⁰Co source. The grafted side chains of poly (acrylic acid) (PAAc) were then cross-linked with gamma radiation at different radiation doses to give net-[PP-g-AAc]. Finally, 4-vinylpyridine (4VP) was grafted into the net-[PP-g-AAc]. The comb-type grafted hydrogel obtained, net-[PP-g-AAc]-g-4VP, has been studied through determination of graft yield and swelling behavior at room temperature. Two critical pH values were found for net-[PP-g-AAc]-g-4VP at 4.5 and 7.2. Initial studies on the immobilization of Cu²⁺ ions from solution into net-[PP-g-AAc]-g-4VP films were performed.The comb-type grafted hydrogel, grafted onto PP was also characterized by differential scanning calorimetry (DSC), scanning electronic microscopy (SEM) and FTIR-ATR.     

Synthesis and characterization of thermosensitive interpenetrating polymer networks based on N-isopropylacrylamide/N-acryloxysuccinimide, crosslinked with polylysine, grafted onto polypropylene

Interpenetrating polymer networks (IPNs) based on poly (N-isopropylacrylamide), (PNIPAAm) and poly (N-acryloxysuccinimide) (PNAS), grafted onto polypropylene (PP), were synthesized in three consecutive steps using ionizing radiation in the first and second steps and chemical reaction in third one. In the first step a thermosensitive graft copolymer of NIPAAm onto PP film was obtained by gamma radiation with a ⁶⁰Co source. The grafted side chains of PNIPAAm were then crosslinked with gamma radiation to give net-[PP-g-NIPAAm]. The secondary network was obtained in situ by chemical crosslinking between PNAS and polylysine (pLys). The PP-g-IPNs exhibited the lower critical solution temperature (LCST) at around 32 °C. Based on its thermoreversible behavior, this system could be used for immobilization of biomolecules. The phase transition temperature (LCST) and network properties of the IPNs were measured by swelling behavior. Additional characterization by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and infrared (FTIR-ATR) determinations are reported.     

Thermo- and pH-responsive polypropylene microporous membrane prepared by the photoinduced RAFT-mediated graft copolymerization

Thermo- and pH-responsive polypropylene microporous membrane prepared by photoinduced reversible addition–fragmentation chain transfer (RAFT) graft copolymerization of acrylic acid and N-isopropyl acrylamide by using dibenzyltrithiocarbonate as a RAFT agent. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR), X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FE-SEM) were used to characterize the structural and morphological changes on the membrane surface. Results of ATR/FT-IR and XPS clearly indicated that poly(acrylic acid) (PAAc) and poly(N-isopropyl acrylamide) (PNIPAAm) were successfully grafted onto the membrane surface. The grafting chain length of PAAc on the membrane surface increased with the increase of UV irradiation time, and decreased with the increase of the concentration of chain transfer agent. The PAAc grafted membranes containing macro-chain transfer agents, or the living membrane surfaces were further functionalized via surface-initiated block copolymerization with N-isopropyl acrylamide in the presence of free radical initiator, 2,2′-azobisisobutyronitrile. It was found that PNIPAAm can be grafted onto the PAAc grafted membrane surface. The results demonstrated that polymerization of AAc and NIPAAm by the RAFT method could be accomplished under UV irradiation and the process possessing the living character. The PPMMs with PAAc and PNIPAAm grafting chains exhibited both pH- and temperature-dependent permeability to aqueous media.     

Gamma radiation synthesis of comb-type graft hydrogels based on poly(acrylic acid) and 4-vinylpyridine

A pH-sensitive comb-type hydrogel was obtained by gamma radiation polymerization and crosslinking of acrylic acid (AAc) in solution. The pH-sensitive 4-vinylpyridine (4VP) was then grafted to the poly acrylic acid (PAAc) hydrogel using gamma radiation from a ⁶⁰Co source. The comb type graft polymers obtained (net-PAAc)-g-4VP has been studied through determination of graft yield and swelling behavior. The critical pH value was found to be 5.6. The apparent mechanical properties appear to be qualitatively better than hydrogels of PAAc upon swelling. The new comb-type system presents faster swelling response (30 h) than the polyacrylic acid hydrogel (50 h). The increase in dose rate from 7.3 to 11.3 kGy h⁻¹, increase the radiation grafting percentage of 4VP in the system. Comb-type polymers were also characterized by DSC, TGA and FTIR-ATR.     

Characterization of N-isopropyl acrylamide/acrylic acid grafted polypropylene nonwoven fabric developed by radiation-induced graft polymerization

Radiation-induced graft copolymerization of N-isopropylacrylamide (NIPAAm) and acrylic acid (AA) mixture was carried out on polypropylene nonwoven fabric to develop a thermosensitive material and has been found to affect the thermal and physical characteristics of fabric. The grafted fabrics with different monomer ratios were characterized by thermal gravimetric analysis (TGA), fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), contact angle and atomic force microscopy (AFM). Results of FTIR clearly indicated that poly(acrylic acid) and poly(N-isopropyl acrylamide) were successfully grafted onto the membrane surface. TGA results showed that the thermal stability of PP fabric increased after grafting of NIPAAm/AA. The crystallinity values from DSC and XRD were found to decrease with increase in degree of grafting because of the addition of grafted chains within the noncrystalline region. The decrease in contact angles of the grafted fabric with an increase of the degree of grafting shows that PNIPAAm/PAA exists as the hydrophilic component. The increase in surface roughness after grafting was observed by AFM.     

Radiation-induced grafting of stimuli-responsive binary monomers: PDMAEMA/PEGMEMA onto PP films

Both poly[2-(dimethylamino) ethyl methacrylate] (PDMAEMA) and poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) were radiation grafted onto polypropylene films (PP) using gamma radiation from a ⁶⁰Co source. PP was pre-irradiated by gamma ray for modification following by grafted PDMAEMA and PEGMEMA by a one step method. Grafting was studied as a function of the pre-irradiation dose between 20 and 180 kGy, dose rate of 10.4 kGy/h, and monomer concentration 50% of PDMAEMA/PEGMEMA (1/1) in different solvents (toluene, acetone, and methanol). FTIR-ATR, TGA, and DSC were carried out in the characterization of the graft copolymer obtained. Stimuli-responsive behavior and critical pH point were studied by swelling in water. pH and thermo-responsive films of PE-g-(DMAEMA/PEGMEMA) presented a lower critical solution temperature (LCST) of 50 °C and critical pH point around 8.7.     

Radiation grafting of NIPAAm and acryloxysuccinimide onto PP films and sequent crosslinking with polylysine

N-isopropylacrylamide (NIPAAm) and N-acryloxysuccinimide (NAS) were grafted from their binary mixtures in tetrahydrofurane (THF) and toluene solutions onto polypropylene (PP) films by the pre-irradiation oxidative method in air. Effects of pre-irradiation dose, dose rate, and monomer concentrations (NAS/NIPAAm) were studied. The grafted copolymers exhibited the lower critical solution temperature (LCST) at around 31 °C. Based on its thermo-reversible behavior, this system has been used for immunoassay, drug delivery, separation processes and immobilization of enzymes. N-acryloxysuccinimide (NAS) has been used as an active ester to bind proteins through amide bond formation with lysine, and because of this property, the grafted copolymer has been crosslinked with polylysine. Techniques used to characterize the films included differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), infrared (FTIR-ATR) and elemental analysis. Results on thermo-sensitivity are presented. This new system could find applications in vesicle immobilizations.     

Thermo‐responsive glycopolymer chains grafted onto honeycomb structured porous films via RAFT polymerization as a thermo‐dependent switcher for lectin Concanavalin a conjugation

Stable and surface‐modified films with regular porous arrays were created by crosslinking honeycomb structured porous films prepared via breath figures from poly(styrene‐co‐maleic anhydride). The formation of open or closed pores of the films was controlled by the addition of a polyion complex. Subsequent crosslinking of the films with 1,8‐diaminooctane led to films, which maintain their structure in solvents. In addition, excess amino functionality after crosslinking allowed the attachment of RAFT agent, 3‐benzylsulfanyl thiocarbonyl sulfanylpropionic acid, for the controlled surface polymerization of N‐isopropyl acrylamide (NIPAAm) and N‐acryloyl glucosamine (AGA). The attachment of thermo‐responsive glycopolymers onto the honeycomb structured porous films was confirmed using contact angle measurements and confocal fluorescence microscopy. Cleavage of surface anchored polymers via aminolysis revealed that the molecular weights of the surface grafted chains are significantly larger than the molecular weight of the chains generated in solution. The honeycomb structured porous films with their grafted PNIPAAm‐ran‐PAGA polymer chains showed selective recognition of Concanavalin A (ConA). Below the lower critical solution temperature (LCST) of the surface, the conjugation is switched off, while above the LCST the surface grafted glucose moieties bind strongly to ConA. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3440–3455, 2010     

Radiation-grafting of 4-vinylpyridine and N-isopropylacrylamide onto polypropylene to give novel pH and thermo-sensitive films

Here 4-vinylpyridine (4VP) was grafted onto polypropylene films (PP) by mutual irradiation method to give PP-g-4VP; N-isopropylacrylamide (NIPAAm) was then grafted onto the PP-g-4VP films to give (PP-g-4VP)-g-NIPAAm by pre-irradiation method, using a ⁶⁰Co γ-source. The dependence of grafting percentage on radiation dose, temperature, reaction time, and monomer concentration was studied. (PP-g-4VP)-g-NIPAAm films were characterized by infrared spectroscopy (FTIR-ATR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The critical pH point and lower critical solution temperature (LCST) were determined by swelling and water contact angle measurements. The LCST also was determined by DSC. The binary graft copolymer films are shown to be thermo-pH sensitive.     

聚丙烯表面接枝PNIPAAm膜Ⅰ.光接枝反应和表面形态结构研究

以氧杂蒽酮或二苯甲酮为引发剂 ,通过紫外光引发表面接枝聚合的方法在聚丙烯薄膜表面引入了具有温度敏感特性的聚异丙基丙烯酰胺 (PNIPAAm)接枝聚合物层 .提高紫外光强度和接枝反应温度均有利于接枝率增大 ,而单体浓度对接枝率的影响存在最佳值 ,为 0 1 8mol L .在引发剂预浸渍引发接枝和休眠基引发接枝这两种方式中 ,后者能够实现更高的接枝率 .红外光谱 (FTIR)、X射线光电子能谱化学分析 (ESCA)和扫描电子显微镜 (SEM)等对接枝层组成的表征结果证实了接枝层的存在 .在不同温度下 ,接枝膜的FTIR谱图中酰胺I带和酰胺II带特征吸收峰发生位移 ,表明它具有温度敏感特性 .同时 ,SEM研究发现由于接枝膜的温度敏感特性而导致的球状表面形态结构     

Conducting polymer films fabricated by oxidative graft copolymerization of aniline on poly(acrylic acid) grafted poly(ethylene terephthalate) surfaces

A conductive polyaniline/poly(ethylene terephthalate) (PANI/PET) composite film was fabricated via the oxidative graft copolymerization of aniline (ANI) onto the plasma-induced poly(acrylic acid) (PAAc) grafted PET surface. The attenuated total reflectance Fourier transform infrared spectroscopy spectra (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS) results confirmed that PANI was successfully grafted onto the surface of the PAAc-g-PET films. The effects of the experimental conditions on the percentage of PANI grafted onto the PAAc-g-PET films were extensively investigated. A very high grafting percentage of ANI can be obtained through the acid-base reaction between the aniline monomer and PAAc on the PAAc-g-PET surface at high temperature. As a result, the grafting percentage of PANI can be increased to as high as 12.18 wt %, which causes the surface resistance of the PANI-g-PAAc-g-PET film to be reduced to about 1000 Omega/sq. We predicted that this is because of the high flexibility of the PAAc molecular chains and high solubility of aniline, both of which facilitate the binding of aniline to PAAc during this high temperature acid-base reaction. It was observed by atomic force microscopy (AFM) that the PANI-modified PET surface exhibits higher size irregularity and surface roughness, which further indicated that a much greater number of aniline molecules can be reactively bonded to and distributed along the grafted AAc chains and that the PANI-g-PAAc-g-PET surface resulting from the sequential oxidative graft copolymerization can possess higher electrical conductivity.     

A boronate affinity restricted-access material with external hydrophilic bottlebrush polymers for pretreatment of cis-diols in biological matrices

Restricted-access materials (RAMs) with an external hydrophilic bottlebrush polymer layer was prepared for sample pretreatment of bioanalysis.     

一步法制备PNIPAAm-g-PAN/PSt载银复合微球及其抗菌性能研究

以AgNO3为金属源,通过乙醇将与聚N-异丙基丙烯酰胺接枝聚丙烯腈/聚苯乙烯（PNIPAAm-g-PAN/PSt）聚合物微球表面酰胺基团配位的银离子（Ag+）还原,一步法制备了PNIPAAm-g-PAN/PSt载银复合微球。通过傅立叶变换红外（FTIR）和紫外-可见光光谱表征发现,由Ag+还原所得的Ag纳米颗粒被成功地固载在PNIPAAm-g-PAN/PSt 微球上;用透射电子显微镜（TEM）对载银微球的大小和形态进行了表征;热重分析（TGA）结果表明,固载在微球表面的银纳米颗粒的含量（质量分数）为12%;抗菌实验结果表明,所制备的载银微球具有抗革兰氏阴性菌的活性。     

Grafting of polymers with controlled molecular weight onto ultrafine silica surface

To graft polymers with controlled molecular weight and narrow molecular weight distribution, the grafting of polymers onto ultrafine silica surface by the termination of living polymer cation with amino groups introduced onto the surface was investigated. The introduction of amino or N-phenylamino groups onto the silica surface was achieved by the treatment of silica with γ-aminopropyltriethxysilane or N-phenyl-γ-aminopropyltrimethoxysilane. It was found that these amino groups on silica are readily reacted with living poly(isobutyl vinyl ether) (polyIBVE), which was generated with CF₃COOH/ZnCl₂ initiating system, and polyIBVE with controlled molecular weight and narrow molecular weight distribution is grafted onto the surface. By the termination of living poly(2-methyl-2-oxazoline), which was generated with methyl p-toluenesulfonate initiator, with amino groups on silica, polyMeOZO was also grafted onto the surface. The percentage of grafting of polymer onto the silica surface decreased with increasing molecular weight of the living polymer, because the steric hindrance of silica surface increases with increasing molecular weight of living polymer. Polymer-grafted silica gave a stable dispersion in a good solvent for grafted chains. © 1995 John Wiley & Sons, Inc.     

Dextran Hydrogels Containing Poly(N‐isopropylacrylamide) as Grafts and Cross‐Linkers Exhibiting Enzymatic Regulation in a Specific Temperature Range

Summary: Specific temperature‐responsive biodegradable hydrogels were synthesized and characterized in terms of their regulation of enzymatic accessibility based on the physical properties of the temperature‐responsive polymers. The hydrogels consist of glycidyl methacrylate‐modified dextran grafted with the poly(N‐isopropylacrylamide) (PNIPAAm) homopolymer, and cross‐linked by co‐polymerization with NIPAAm and N,N‐dimethylacrylamide (DMAAm). The coil‐globule change in the grafted poly(NIPAAm) chains and only a slight dehydration of the poly(NIPAAm‐co‐DMAAm) cross‐linkers are effective in controlling the enzymatic degradation over a specific temperature range.

The thermo‐responses of the graft chains (steric hindrance) and the crosslinkers (slight deswelling of the hydrogel networks) control the enzymatic degradation of the hydrogel.     

Surface modification of polymers. IV. UV initiated degradation of polymers with stabilizers grafted onto the surface

Polypropylene (PP), Polyethylene (PE), and polystyrene (PS) films were grafted with glycidylmethacrylate in thin surface layers. To the oxiran groups thus grafted onto the surface three UV stabilizers were attached, 4-amino-2,2,6,6-tetramethylpiperidine (AP), 2,4-dihydroxybenzophenone (DHBP), and phenyl 4-aminosalicylate (PAS). The amount of stabilizer grafted onto the surface varied between 25 and 40 nmol/cm² depending on the polymer substrate. The samples were exposed to UV radiation in air, and the degradation and oxidation of the polymers were studied with IR, UV, and ESCA spectroscopy and by stress–strain measurements. PP grafted with AP exhibited a near 20-fold increase in lifetime compared with the unprotected PP, AP did not stabilize the PE or PS samples. DHBP was an efficient stabilizer of PE, the oxidation rate of the grafted sample being 1/2 to 1/3 of the ungrafted. A similar effect was observed when DHBP was grafted onto PP and PS. PAS underwent a rearrangement reaction when irradiated with UV light, and had only a slight stabilizing effect.     

Synthesis, characterization and thermoreversible behaviours of poly(dimethyl siloxane)/poly(N-isopropyl acrylamide) semi-interpenetrating networks

Simultaneous and sequential poly(N-isopropyl acrylamide) (PNIPAAm)/poly(dimethyl siloxane) (PDMS) semi-interpenetrating polymer networks (IPNs) with different linear PDMS contents were prepared by free radical polymerization method. Their phase morphologies have been characterized by FTIR, DSC and SEM. The simultaneous semi-IPNs exhibited phase transition temperatures (T_pt) shifted higher temperature from glass transition temperatures (T_g) of their respective homopolymers, suggesting a heterophase morphology and only physical entanglement between the PNIPAAm network and linear PDMS with high molecular weight (Mn≈9000 g/mol). For sequential semi-IPNs, the shift of T_pts towards lower temperature suggested that the chemical interaction between the constituents of the IPNs increased with increasing PDMS content in the network. In addition, these semi-IPNs were characterized for their thermo-sensitive behaviour by equilibrium swelling studies. The results showed that incorporation of hydrophobic PDMS polymer into the thermo- and pH-sensitive PNIPAAm and P(NIPAAm-co-IA) (itaconic acid) hydrogels by semi-IPN formation decreased swelling degrees of IPNs without affecting their LCSTs whereas addition of acrylated PDMS (Tegomer V-Si 2250) as crosslinker instead of N,N^′-methylenebisacrylamide (BIS) into the structures of these hydrogels changed their LCSTs along with their swelling degrees.     

Synthesis of PNIPAAm-g-P4VP Microgel as Draw Agent in Forward Osmosis by RAFT Polymerization and Reverse Suspension Polymerization to Improve Water Flux

Microgels have unique and versatile properties allowing their use in forward osmosis areas as a draw agent. In this contribution, poly(4-vinylpyridine) (P4VP) was synthesized via RAFT polymerization and then grafted to a poly(N-Isopropylacrylamide) (PNIPAAm) crosslinking network by reverse suspension polymerization. P4VP was successfully obtained by the quasiliving polymerization with the result of nuclear magnetic resonance and gel permeation chromatography characterization. The particle size and particle size distribution of the PNIPAAm-g-P4VP microgels containing 0, 5, 10, 15 and 20 wt% P4VP were measured by means of a laser particle size analyzer. It was found that all the microgels were of micrometer scale and the particle size was increased with the P4VP load. Inter/intra-molecular-specific interactions, i.e., hydrogen bond interactions were then investigated by Fourier infrared spectroscopy. In addition, the water flux measurements showed that all the PNIPAAm-g-P4VP microgels can draw water more effectively than a blank PNIPAAm microgel. For the copolymer microgel incorporating 20 wt% P4VP, the water flux was measured to be 7.48 L∙m⁻²∙h⁻¹.     

Encapsulation of silica nanoparticles by redox-initiated graft polymerization from the surface of silica nanoparticles

This study describes a facile and versatile method for preparing polymer-encapsulated silica particles by ‘grafting from’ polymerization initiated by a redox system comprising ceric ion (Ce⁴⁺) as an oxidant and an organic reductant immobilized on the surface of silica nanoparticles. The silica nanoparticles were firstly modified by 3-aminopropyltriethoxysilane, then reacted with poly(ethylene glycol) acrylate through the Michael addition reaction, so that hydroxyl-terminated poly(ethylene glycol) (PEG) were covalently attached onto the nanoparticle surface and worked as the reductant. Poly(methyl methacrylate) (PMMA), a common hydrophobic polymer, and poly(N-isopropylacrylamide) (PNIPAAm), a thermosensitive polymer, were successfully grafted onto the surface of silica nanoparticles by ‘grafting from’ polymerization initiated by the redox reaction of Ce⁴⁺ with PEG on the silica surface in acid aqueous solutions. The polymer-encapsulated silica nanoparticles (referred to as silica@PMMA and silica@PNIPAAm, respectively) were characterized by infrared spectroscopy, thermogravimetric analysis, and transmission electron microscopy. On the contrary, graft polymerization did not occur on bare silica nanoparticles. In addition, during polymerization, sediments were observed for PMMA and for PNIPAAm at a polymerization temperature above its low critical solution temperature (LCST). But the silica@PNIPAAm particles obtained at a polymerization temperature below the LCST can suspend stably in water throughout the polymerization process.