Carbon nanotubes and fullerene in the solution polymerisation of acrylonitrile

The radical activity of single wall carbon nanotubes (SWCNT) and fullerene C₆₀ in the radical polymerisation of acrylonitrile (AN) in N,N-dimethylformamide (DMF) initiated by 2,2′-azobis[2-methyl-ω-hydroxy-oligo(oxyethylene) propionate] [AIB-OOE(4 0 0)] and 2,2′-azoisobutyronitrile (AIBN) at 333 K was investigated in situ using a dilatometric method. The carbonaceous substances were sonicated in DMF before the polymerisation. The changes in the process proceeding in the presence of SWCNT and C₆₀ in a comparison to the course of AN polymerisation without the participation of carbonaceous substances (the decrease of the reaction rate, the induction time) indicated on the inhibition effect, which can be described quantitatively using the inhibition parameter F. Single wall carbon nanotubes were found to act as retarders whereas fullerene C₆₀ as an inhibitor in the AN polymerisation. The changes in the chemical structure of products reveal that the carbon nanotubes and fullerenes are chemically bonded with the polymer.     

Novel soluble fluorinated aromatic polyamides derived from 2-(4-trifluoromethylphenoxy)terephthaloyl chloride with various aromatic diamines

A series of novel fluorinated aromatic polyamides derived from a new monomer, 2-(4-trifluoromethylphenoxy)terephthaloyl chloride (TFTPC), with various aromatic diamines were synthesized and characterized. The polyamides were obtained in high yields and moderately high inherent viscosities ranging from 1.07 to 1.16 dL/g. All the polyamides were amorphous and readily soluble in many organic solvents, such as N-methyl-2-pyrrolidinone (NMP), N,N′-dimethylacetamide (DMAc), N,N′-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO), and could afford flexible and tough films via solution casting. The cast films exhibited good mechanical properties with tensile strengths of 82.8-107.3 MPa, elongation at break of 4.1-7.2%, and tensile modulus of 2.26-3.95 GPa. These polyamide films also exhibited good thermal stability with the glass transition temperature of 222-294 °C, the temperature at 5% weight loss of 442-472 °C in nitrogen. They exhibited low dielectric constants ranging from 3.25 to 3.39 (1 MHz), low moisture absorption in the range of 1.32-2.45%, high transparency with an ultraviolet-visible absorption cut-off wavelength in the 330-371 nm range, and excellent electrical properties.     

The effect of processing conditions on the mechanical properties and thermal stability of highly oriented PP tapes

It has previously been shown possible to use highly oriented polypropylene (PP) tapes to create self-reinforced (all-PP) composites. It is desirable to understand the relationship between tape processing parameters and the mechanical properties and thermal stability of the tapes, as these tape properties will govern the ultimate properties of the all-PP composite. In this paper, the effects of the tape drawing parameters such as draw ratio (λ), drawing temperature and thermal annealing on the final mechanical properties, density and dimensional thermal stability of the tapes are presented. PP tapes drawn to λ = 17 possess tensile moduli of ～15 GPa and tensile strengths of ～450 MPa. PP tapes with high draw ratios, λ > 9.3, show a decrease in density, a change from transparent to opaque appearance and increased dimensional thermal stability with increasing draw ratio. The results of an investigation into the effects of a thermal annealing step, targeted at improving the dimensional thermal stability of these highly oriented PP tapes, are also presented.     

Characterisation of N-vinyl-2-pyrrolidone-based hydrogels prepared by a Diels-Alder click reaction in water

N-vinyl-2-pyrrolidone-based hydrogels were prepared by the Diels-Alder reaction in water for the first time. Copolymers of N-vinyl-2-pyrrolidone(VP) and furfuryl methacrylate(FM) were synthesised by free radical polymerisation in toluene at 70 °C by using 2,2′-azobisisobutyronltrile as an initiator. Polymeric dienophile (PEG-AMI) was prepared from N-alaninyl maleimide (AMI) and poly(ethylene glycol) (PEG) by using N,N′-dicyclohexylcarbodiimide (DCC) as a dehydrating agent. The prepared dienes and dienophile were then dissolved in water and mixed, leading to gelation via Diels-Alder reaction after some time. The gelation times of different copolymers and PEG-AMI in different solvents and at different temperatures were measured by the vial inversion method, and the swelling behaviour of dried hydrogels was studied using a general gravimetric method. The gelation time was shorter in water than in organic solvents, and the gelation time decreased with the increase of temperature and FM content in copolymers. Conversely, the swelling ratios increased with the decrease of temperature and FM content in the copolymers. Disassembly experiments suggested that N,N-dimethylformamide (DMF) could accelerate the retro-DA reaction.     

Novel thermally stable and chiral poly(amide-imide)s bearing from N,N′-(4,4′-diphthaloyl)-bis-l-isoleucine diacid: Synthesis and characterization

Novel optically active aromatic poly(amide-imide)s (PAIs) were prepared from newly synthesized N,N′-(4,4′-diphthaloyl)-bis-l-isoleucine diacid (3) via polycondensation with various diamines. The diacid was synthesized by the condensation reaction of 3,3′,4,4′-biphenyltetracarboxylic dianhydride (1) with l-isoleucine (2) in a mixture of acetic acid and pyridine (3:2 v/v). All the polymers were obtained in quantitative yields with inherent viscosities of 0.20-0.43 dL g⁻¹. All the polymers were highly organosoluble in solvents like N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), tetrahydrofuran, γ-butyrolactone, cyclohexanone and chloroform at room temperature or upon heating. These poly(amide-imide)s had glass transition temperatures between 198 and 231 °C, and their 10% weight-loss temperatures were ranging from 368 to 398 °C and 353 to 375 °C under nitrogen and air, respectively. The polyimide films had tensile strengths in the range of 63-88 MPa and tensile moduli in the range of 0.8-1.4 GPa. These poly(amide-imide)s possessed chiral properties and the specific rotations were in the range of −3.10° to −72.92°.     

Multiwalled carbon nanotubes covalently functionalized with poly(N‐vinylcarbazole) via RAFT polymerization: Synthesis and nonliner optical properties

The poly(N‐vinylcarbazole)‐grafted MWNTs (MWNT‐PVK) hybrid materials were synthesized in the presence of S‐1‐Dodecyl‐S′‐(α, α′‐dimethyl‐α″‐acetic acid) trithiocarbonate (DDAT)‐covalently functionalized multiwalled carbon nanotubes (MWNT‐DDAT) as reversible addition–fragmentation chain transfer (RAFT) agent. Incorporation of the PVK moieties onto the MWNTs surface can considerably improve the solubility and processability of MWNTs. For all MWNT‐PVK hybrid materials, they are soluble in some common organic solvents such as toluene, THF, chloroform, DMF and others. In contrast to the UV/Vis spectrum of DDAT‐PVK, which was synthesized by use of DDAT as RAFT agent under the same synthetic condition, in the visible region, the absorption spectrum of MWNT‐PVK exhibited a typical electronic absorption characteristics of solubilized carbon nanotubes, in which the absorbance decreases gradually in the range of 350–600 nm. At the same level of linear transmission the MWNT‐PVK with 79.2% PVK moieties in the material structure possesses best optical limiting performance in comparison with the other MWNT‐PVK composites, MWNTs and C₆₀. The significant NLO responses manifest the MWNT‐PVK materials suitable candidate for viable optical limiting devices. Light scattering, originating from the thermal‐induced microplasmas and/or microbubbles, is responsible for the optical limiting. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3161–3168, 2010     

Solvent-assisted thiocarboxylation of amines and alcohols with carbon monoxide and sulfur under mild conditions

DMSO or DMF as a solvent strongly accelerated the thiocarboxylation of amines and alcohols with carbon monoxide and sulfur. Under mild conditions (1 atm, 20 °C), this thiocarboxylation of amines assisted by DMSO with carbon monoxide and sulfur has been developed into a practical and convenient synthetic method for S-alkyl thiocarbamates in good to excellent yields, including EPTC, thiobencarb, orbencarb, and molinate (herbicides). DMF also showed the similar solvent effect. NMP slightly decreased the effect for the thiocarboxylation of amines, and the yield of S-alkyl thiocarbamate was lowered in DMAc. Surprisingly, no formation of S-alkyl thiocarbamate was observed at the use of the other solvents, such as THF, hexane, toluene, AcOEt, MeCN, MeOH, and H₂O. The present solvent-assisted thiocarboxylation with carbon monoxide and sulfur could be also applied to a new synthesis of S-alkyl O-alkyl carbonothioates from alcohols under mild conditions (1 atm, 20 °C) in DMF using DBU (1,8-diazabicyclo[5.4.0]undec-7-ene).     

Sulfonated polyaniline network grafted multi-wall carbon nanotubes for enzyme immobilization, direct electrochemistry and biosensing of glucose

A new nanomaterial was prepared by grafting a layer of sulfonated polyaniline network (SPAN-NW) on to the surface of multi-walled carbon nanotube (MWNT) and effectively utilized for immobilization of an enzyme and for the fabrication of a biosensor. SPAN-NW was formed on the surface of MWNT by polymerizing a mixture of diphenyl amine 4-sulfonic acid (DPASA), 4-vinyl aniline (VA) and 2-acrylamido-2-methyl-1-propane sulfonic acid (APASA) in the presence of amine functionalized MWNT (MWNT-NH₂). The MWNT-g-SPAN-NW was immobilized with glucose oxidase (GOx) to fabricate the SPAN-NW/GOx biosensor. MWNT-g-SPAN-NW/GOx electrode showed direct electron transfer (DET) for GOx with a fast heterogeneous electron transfer rate constant (k_s) of 4.11 s^− 1. The amperometric current response of MWNT-g-SPAN-NW/GOx biosensor shows linearity up to 9 mM of glucose, with a correlation coefficient of 0.99 and a detection limit of 0.11 μM (S/N = 3). At a low applied potential of − 0.1 V, MWNT-g-SPAN-NW/GOx electrode possesses high sensitivity (4.34 μA mM^− 1) and reproducibility towards glucose.     

Solvent effects on jet evolution during electrospinning of semi-dilute polystyrene solutions

Linear polystyrene with a weight average molecular weight of 393,400 g/mol was used with various solvents including tetrahydrofuran (THF), chloroform, carbon disulfide (CS₂), 1-methyl-2-pyrrolidinone (NMP), and N,N-dimethylformamide (DMF) to produce solutions, corresponding to a Berry number of about 9. The jet breakdown behavior of each of these solutions was studied with a high speed camera (2000 frames/s). The structure of the electrospun polymer was examined with a scanning electron microscope. The results indicate that jet breakdown with THF and chloroform entailed significant extensional flow, followed by the onset of instabilities, leading to the formation of numerous secondary jets under steady-state conditions. By comparison, the solution jets with DMF and NMP exhibit extensive whipping and splaying to produce a cloud of jets. In this case, few secondary jets were observed under steady-state conditions. A highly refined structure was observed in the electrospun polymer for NMP and DMF, in accordance with the extensive instabilities observed during jet breakdown. Limited jet instability observed with CS₂ solution suggests the significant effect of solvent evaporation. Typical primary jet velocities were measured to be on the order of 2-5 m/s.     

FT-IR studies on the mechanical response of the crystalline fraction in ultrastrong polyethylene tapes

FT-IR spectra of UHMW-PE tapes with different moduli have been studied in dependence of mechanical deformation and stress. Small spectral variations have been revealed in the difference spectra. Band shifts of the 730/720 cm^–1 doublet have been observed under stress relaxation and upon stretching. A clear correlation between the shift of crystalline bands and the Young's modulus could be determined. Polarized measurements demonstrated variations in the mechanical response of nearly perfectly oriented and non-oriented crystallites. Crosslinking was performed by blending the polyethylene with 10% polysilane and UV-irradiation of the drawn material. The band shift increases as the linkage between oriented crystal blocks is improved with higher draw ratios and chemical crosslinking.     

Simultaneous determination of epinephrine and norepinephrine in human blood plasma and urine samples using nanotubes modified edge plane pyrolytic graphite electrode

The simultaneous determination of catecholamines - epinephrine and norepinephrine by square wave voltammetry (SWV) at physiological pH 7.2 is reported using multi-walled carbon nanotubes modified edge plane pyrolytic graphite electrode (MWNT/EPPGE). A broad bump at ∼250 mV is appeared for the oxidation of epinephrine (EP) and norepinephrine (NE) at bare EPPGE whereas at MWNT/EPPGE two well-separated peaks at ∼150 and ∼215 mV are appeared for the oxidation of EP and NE, respectively. The oxidation peak current of both the neurotransmitters also increased significantly along with the negative shift of peak potentials using MWNT/EPPGE. The oxidation of both compounds occurred in a pH dependent, 2e and 2H⁺ process and the electrode reaction followed diffusion controlled pathway. Linear calibration curves were obtained for epinephrine and norepinephrine in the range 0.5-100 nM with limits of detection 0.15 × 10⁻⁹ and 0.90 × 10⁻¹⁰ M, respectively. The developed protocol is implemented for the simultaneous determination of epinephrine and norepinephrine in blood plasma and urine samples of smokers as well as in athletes.     

Polyethylene thermal oxidative stabilisation in carbon nanotubes based nanocomposites

Multiwall carbon nanotubes (MWNT)/linear low density polyethylene (LLDPE) nanocomposites were studied in order to understand the stabilisation mechanism for their thermal and oxidative degradation. Thermogravimetry coupled with infrared evolved gas analysis and pyrolysis gas chromatography-mass spectrometry demonstrate that MWNT presence slightly delays thermal volatilisation (15-20 °C) without modification of thermal degradation mechanism. Whereas thermal oxidative degradation in air is delayed by about 100 °C independently from MWNT concentration in the range used here (0.5-3.0 wt.%). The stabilisation is due to formation of a thin protective film of MWNT/carbon char composite generated on the surface of the nanocomposites is shown by SEM and ATR FTIR of degradation residues. The film formation mechanism is discussed.     

New soluble, thermally stable poly(amide-imide)s containing cardo anthraquinone unit

Preparation of new types of polyimides with high thermal stability and improved solubility was considered. In this way, two new amide diamines containing bulky pendant units were prepared in two steps: nucleophilic substitution reactions of 1- and 2-aminoanthraquinone with 3,5-dinitrobenzoyl chloride to form amide containing dinitro compounds, and then reduction of resulted dinitro compounds with hydrazine monohydrate in the presence of palladium/activated carbon. Two series of new poly(amide-imide)s were prepared from the reactions of these two diamines with various dianhydrides by one step polyimidation process. All poly(amide-imide)s were characterized by FTIR and ¹H-NMR spectroscopies and elemental analysis. The polymers were obtained in high yields with inherent viscosities of 0.54-0.69 dl g⁻¹. X-ray diffraction patterns (XRD) showed that all the polymers were amorphous and therefore this factor in addition to the introduction of bulky anthraquinone group led to good solubility of the polymers in most common organic solvents especially in N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), and dimethylsulfoxide (DMSO). Thermal analysis showed glass transition temperature between 204 and 226 °C. Decomposition temperatures were more than 293 °C, also 10% weight loss were in the range of 387-419 °C in air.     

Electrochemical reduction and voltammetric determination of metronidazole at a nanomaterial thin film coated glassy carbon electrode

Simple and sensitive electrochemical method for the determination of metronidazole, based on a nanostructured film coated glassy carbon electrode (GCE), is described. Multi-walled carbon nanotubes (MWNT) was dispersed into water in the presence of a hydrophobic surfactant to give very stable and homogeneous MWNT suspension, and a MWNT-film coated GCE was achieved via evaporating solvent. Metronidazole yields a well-defined reduction peak whose potential is −0.71 V at the MWNT-film coated GCE in pH 9.0 Britton-Robinson buffer. Compared with bare GCE, the MWNT-film modified GCE significantly enhances the reduction peak current of metronidazole. All the experimental parameters were optimized for the determination of metronidazole. The detection limit is 6×10⁻⁹ mol/l at 2 min accumulation. This method has been successfully used to determine metronidazole in the drugs. Furthermore, results obtained by the proposed method have been compared with spectrophotometric method.     

Microwave-assisted clean synthesis of aromatic photoactive polyamides derived from 5-(3-acetoxynaphthoylamino)-isophthalic acid and aromatic diamines in ionic liquid

Dicarboxylic acid, 5-(3-acetoxynaphthoylamino)isophthalic acid was prepared in three steps. The direct polycondensation of this novel diacid with several aromatic diamines was studied in 1,3-diisopropylimidazolium bromide as an ionic liquid (IL) under microwave irradiation and conventional heating. The polymerization reaction was effectively preceded in IL, and triphenyl phosphite as an activating agent, and the resulting novel photoactive polyamides were obtained in high yields and moderate inherent viscosities in the range of 0.44-0.69 dL/g. Thermogravimetric analysis showed that polymers are thermally stable, 10% weight loss temperatures in excess of 390 and 470 °C, and char yields at 600 °C in nitrogen higher than 60%. These macromolecules exhibited maximum UV-vis absorption at 265 and 300 nm in N,N-dimethylformamide (DMF) solution. Their photoluminescence in DMF solution demonstrated fluorescence emission maxima around 361 and 427 nm for all of the polyamides. It is very important to note that, because of, high polarizability of ILs, they are very good solvents for absorbing microwaves.     

Synthesis of aromatic poly(amide-imide)s from novel diimide-diacid (DIDA) containing sulphone and bulky pendant groups by direct polycondensation with various diamines

A novel diimide-diacid (DIDA) monomer, 4-{4-[(4-methyl phenyl) sulphonyl]}-1,3-bis-trimellitoimido benzene containing sulphone and bulky pendant groups was successfully synthesized and used to synthesize a series of wholly aromatic poly(amide-imide)s (PAIs) by direct polycondensation method. The direct polycondensation of newly synthesized DIDA with different diamines was carried out via Yamazaki’s phosphorylation method using triphenyl phosphite and pyridine system. The resulting poly(amide-imide)s were obtained in quantitative yields with inherent viscosities 0.36-0.47 dl/g in DMAc at 30 ± 0.1 °C. The poly(amide-imide)s were amorphous and were readily soluble in various solvents such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethylsulfoxide (DMSO), and pyridine. Tough and flexible films were obtained by casting their DMAc solution. According to thermogravimetric analysis, the polymers were fairly stable up to temperature around 396 °C, and 10% weight losses in the temperature range of 476-511 °C that showed good thermal stabilities of these polymers.     

High glass transitions of novel organosoluble polyamide-imides based on noncoplanar and rigid diimide-dicarboxylic acid

A series of novel polyamide-imides (PAIs) with high glass transition temperature were prepared from diimide-dicarboxylic acid, 2,2′-bis(trifluoromethyl)-4,4′-bis(trimellitimidophenyl)biphenyl (BTFTB), by direct polycondensation with various diamines in N-methyl-2-pyrrolidinone using triphenyl phosphite and pyridine as condensing agents in the presence of dehydrating agent (CaCl₂). The yield of the polymers was obtained was high with moderate to high inherent viscosities (0.80-1.03 dL g⁻¹). Gel permeation chromatography (GPC) of the polymers showed number-average and weight-average molecular weights up to 8.6 × 10⁴ and 22 × 10⁴, respectively. The PAIs were amorphous in nature. Most of the polymers exhibited good solubility in various solvents such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), pyridine, cyclohexanone and tetrahydrofuran. The polymer films had tensile strength in the range of 79-103 MPa, an elongation at break in the range of 6-16%, and a tensile modulus in the range between 2.1 and 2.8 GPa. The glass transition temperatures of the polymers were determined by DMA method and they were in the range of 264-291 °C. The coefficients of thermal expansion (CTE) of PAIs were determined by TMA instrument and they were between 29 and 67 ppm °C⁻¹. These polymers were fairly thermally stable up to or above 438 °C, and lose 10% weight in the range of 446-505 °C and 438-496 °C, respectively, in nitrogen and air. These polymers had exhibited 80% transmission wavelengths which were in the range of 484-516 nm and their cutoff wavelengths were in between 418 and 434 nm. The PAIs with trifluoromethyl group have higher bulk density resulting in higher free volume and then lowering the dielectric constant.     

Electrochemical detection of DNA hybridization based on polypyrrole/ss-DNA/multi-wall carbon nanotubes paste electrode

A sensitive electrochemical detection of DNA hybridization using a paste electrode assembled by multi-wall carbon nanotubes (MWNT) and immobilizing DNA probe within electropolymerized polypyrrole (ppy) was developed. The detection approach relied on entrapping of DNA probe within electropolymerized ppy film on the MWNT paste electrode and monitoring the current change generated from an electroactive intercalator of ethidium bromide (EB) after DNA hybridization. As a consequence of DNA hybridization, significant changes in the current of EB intercalated with double-stranded DNA (ds-DNA) on the MWNT paste electrode were observed. Based on the response of EB, only the complementary DNA sequence gave an obvious current signal compared with the five-point mismatched and non-complementary sequences. The oxidation peak current was linearly related to the logarithm of the concentration of the complementary DNA sequence from 1.0 × 10⁻¹⁰ to 1.0 × 10⁻⁸ M with a detection limit of 8.5 × 10⁻¹¹ M. This work demonstrates that the incorporation of MWNT paste electrode with electropolymerization is a promising strategy of functional interfaces for the immobilization of biological recognition elements.     

New film-forming poly(urethane-amide-imide) block copolymers: influence of soft block on membrane properties for the purification of a fuel octane enhancer by pervaporation

A new family of eight poly(urethane-amide-imide) (PUAI) block copolymers with the same hard block and different soft blocks were synthesized in two steps from a dianhydride monomer containing amide functions (4,4′-methylene-bis(trimellitic anhydride-N-phenylamide)) and α,ω-dihydroxy telechelic oligomers which varied in both chemical structure (polyethers: PEG, PTMG, PPG; polyester: PCL) and molar weight (MW ≅ 600 or 1000 g/mol). The PUAI were obtained in high yields (ranging from 81 to 98 wt%) and with reduced viscosities which varied from 0.36 to 0.84 dL/g (for C = 1 mg/mL in DMF at 25 °C). Their characterization by FTIR and ¹H NMR fully confirmed their chemical structure. Their solubility was typically limited to a few wt/vol% even in strong apolar diprotic solvents like DMF and NMP. This particular feature showed the very strong physical cross-linking of their very stiff hard block and enabled to cast membranes capable of withstanding exposure to many common organic solvents. Systematic permeability experiments showed that the PUAI membranes could be used to separate the azeotropic mixture EtOH (20 wt%)/ETBE very easily, with interesting prospects for the purification of ETBE (a fuel octane enhancer used instead of lead derivatives in the European Community). An analysis in terms of structure-property relationships pointed out that the soft block molar weight and polarity were two key parameters for the optimization of selective permeability. The best compromise was obtained with the soft block PEG1000. The corresponding polymer led to performances so far outstanding for polyamideimides with a very high flux of more than 1.1 kg/h m² for a normalized thickness of 5 μm at 50 °C and a selectivity α = 22.7 in the high range for this kind of separation.     

N-picolinamides as ligands for Ullmann-type homocoupling reactions

The use of N-phenylpicolinamide (NPPA) as a ligand in Ullmann-type homocoupling reactions of aryl iodides and bromides in common solvents, such as DMF and MeCN has been successfully demonstrated at room temperature. In addition, this work provided the first example of the homocoupling of an aryl chloride at 82 °C, which is a relatively low temperature when compared to regular Ullmann reaction temperatures. Also, NPPA was successfully employed in base—and heat free Suzuki reactions, including electron rich and poor aryl halides with heteroarylboronic acids in moderate yields.