Thermal properties and stability of cassava starch films cross-linked with tetraethylene glycol diacrylate

The thermal stability of starch cross-linked with tetraethylene glycol diacrylate was studied under nitrogen atmosphere by thermogravimetry (TG) and infrared spectroscopy (FTIR). The cross-linking reaction was confirmed by the increase in intensity of the absorption band at ca. 3330 cm⁻¹ indicating the reinforcement of hydrogen bonds and the appearance of a new band at 1726 cm⁻¹ associated with the carbonyl group of the cross-linking agent. After cross-linking the solubility of starch in water decreased to the range 9%-16%. The thermogravimetric curves of pure and cross-linked starches showed an initial stage of degradation (up to ca. 150 °C) associated with the loss of water. The main stage of degradation occurred in the range 250-400 °C corresponding to ca. 60%-70% mass loss. The activation energy (E) for the degradation process increased from 145 kJ mol⁻¹ (pure starch) to 195 kJ mol⁻¹ and 198 kJ mol⁻¹ for starch treated for 60 min by UV (30 °C) and at 90 °C, suggesting high stability after cross-linking. A higher value (240 kJ mol⁻¹) was obtained for starch treated by UV for 120 min. The main volatile products determined by FTIR which correspond to hydrocarbons and carbonyl groups are apparently associated with the scission of weak bonds in the chain (probably branched groups) and the scission of stronger bonds (glycosidic linkages), respectively.     

Curing kinetics of arylamine-based polyfunctional benzoxazine resins by dynamic differential scanning calorimetry

In this study, the curing kinetics of polyfunctional benzoxazine resins based on arylamine, i.e. aniline and 3,5-xylidine, designated as BA-a and BA-35x, respectively, were investigated. Non-isothermal differential scanning calorimetry (DSC) at different heating rates is used to determine the kinetic parameters and the kinetic models of the curing processes of the arylamine-based polyfunctional benzoxazine resins were proposed. Kissinger, Ozawa, Friedman, and Flynn-Wall-Ozawa methods were utilized to determine the kinetic parameters of the curing reaction. BA-a resin shows only one dominant autocatalytic curing process with the average activation energy of 81-85 kJ mol⁻¹, whereas BA-35x exhibits two dominant curing processes signified by the clear split of the curing exotherms. The average activation energies of low-temperature curing (reaction (1)) and high-temperature curing (reaction (2)) were found to be 81-87 and 111-113 kJ mol⁻¹, respectively. The reaction (1) is found to be autocatalytic in nature, while the reaction (2) exhibits nth-order curing kinetics. In addition, the predicted curves from our kinetic models fit well with the non-isothermal DSC thermogram.     

Bismaleimide and bispropargyl ether blends: Curing kinetics—Model free approach

Two structurally different bismaleimides, namely 2,2-bis[4-(4-maleimidophenoxy-phenyl)]propane (BMIX) and 5(6)-maleimide-1(4′-maleimidophenyl)-1,3,3′-trimethyl indane (BMII) and bispropargyl ether of bisphenol A (BPEBPA) were prepared. The two bismaleimides were separately blended with BPEBPA in different mole ratios [BMIX/BMII: BPEBPA = 100: 0, 75: 25, 50: 50, 25: 75, 0: 100%] and the materials were thermally polymerized at 230°C. The curing studies of the monomers and blends reveal that the blending of BMIX and BMII with BPEBPA decreases the curing temperature window. Blending of 25% of either BMIX or BMII with BPEBPA drastically reduces the curing enthalpy and was nearly half the value of pure BPEBPA. The FTIR spectra of the cured materials show that the chromene ring stretching frequency of BPEBPA decreases as the bismaleimide content increases and new absorption peaks corresponding to cyclopentane (941 cm^?1) and cyclohexane (1018 cm^?1) appeared. The curing kinetics of the monomers and blends were studied using three model free kinetic methods. The trend noted for the variation of apparent activation energies for curing of 25% BMIX + 75% BPEBPA blend is different compared to the monomers and other blends.     

Thermodegradation kinetics of a hybrid inorganic-organic epoxy system

Lifetime of the epoxy system formed by diglycidyl ether of bisphenol A, DGEBA/4,4′-diaminediphenylmethane, DDM, modified with the silsesquioxane, glycidylisobutyl-POSS, was calculated from thermogravimetric analysis. The activation energy of the decomposition of this system was evaluated by the integral method developed by Flynn-Wall-Ozawa (E = 88.9 ± 2.1 kJ mol⁻¹) and by Coats and Redfern method (E = 85.2 ± 1.5 kJ mol⁻¹). The kinetic parameters have been used to estimate the lifetime of the system POSS/DGEBA/DDM. The obtained results by two different ways are similar.     

Critical evaluation of global mechanisms of wood devolatilization

Thermogravimetric data on the devolatilization rate of beech wood are re-examined with the aim of incorporating the effects of high heating rates (up to 108 K min⁻¹) in the global kinetics. The mechanism consisting of three independent parallel reactions, first-order in the amount of volatiles released from pseudo-components with chief contributions from hemicellulose, cellulose and lignin, is considered first. It is found that the set of activation energies estimated by Gronli et al. [M.G. Gronli, G. Varhegyi, C. Di Blasi, Ind. Eng. Chem. Res. 41 (2002) 4201-4208] (100, 236 and 46 kJ mol⁻¹, respectively) for one slow heating rate results in very high deviations between predicted and measured rate curves. The agreement is significantly improved by a new set of data consisting of activation energies of 147, 193 and 181 kJ mol⁻¹, respectively. In this case, the overlap is reduced between the reaction rates of the three pseudo-components whose chemical composition is also modified. In particular, instead of a slow decomposition rate over a broad range of temperatures, the activity of the third reaction is mainly explicated along the high-temperature (tail) region of the weight loss curves. The performances of more simplified mechanisms are also evaluated. One-step mechanisms, using literature values for the kinetic constants, produce large errors on either the conversion time (activation energy of 103 kJ mol⁻¹) or the maximum devolatilization rate (activation energy of 149 kJ mol⁻¹). On the other hand, these parameters are well predicted by two parallel reactions, with activation energies of 147 and 149 kJ mol⁻¹.     

Adsorption of arsenic(III) into modified lamellar Na-magadiite in aqueous medium—Thermodynamic of adsorption process

Synthetic Na-magadiite sample was used for organofunctionalization process with N-propyldiethylenetrimethoxysilane and bis[3-(triethoxysilyl)propyl]tetrasulfide, after expanding the interlayer distance with polar organic solvents such as dimethylsulfoxide (DMSO). The resulted materials were submitted to process of adsorption with arsenic solution at pH 2.0 and 298±1 K. The adsorption isotherms were adjusted using a modified Langmuir equation with regression nonlinear; the net thermal effects obtained from calorimetric titration measurements were adjusted to a modified Langmuir equation. The adsorption process was exothermic (Δ_intH=−4.15-5.98 kJ mol⁻¹) accompanied by increase in entropy (Δ_intS=41.32-62.20 J k⁻¹ mol⁻¹) and Gibbs energy (Δ_intG=−22.44−24.56 kJ mol⁻¹). The favorable values corroborate with the arsenic (III)/basic reactive centers interaction at the solid-liquid interface in the spontaneous process.     

Thermal decomposition of native cellulose: Influence on crystallite size

The thermal degradation behavior of crystalline cellulose has been investigated using thermogravimetry, differential thermal analysis, and derivative thermogravimetry in a nitrogen atmosphere. Three cellulose samples, Halocynthia, cotton, and commercial microcrystalline cellulose Funacel, were used in this study to analyze the influence on crystallite size. They all belongs to cellulose I_β type and those crystallite sizes calculated from the X-ray diffractometry profiles by Scherrer equation were very different in the order Halocynthia > cotton > Funacel. The thermal decomposition of cellulose shifted to higher temperatures with increasing crystallite size. However, activation energies for the thermal degradation were the almost the same among the samples: 159-166 kJ mol⁻¹. These results indicated that the crystal structure does not affect the activation energy of the thermal degradation but the crystallite size affects the thermal degradation temperature.     

Comparative studies on the curing kinetics and thermal stability of tetrafunctional epoxy resins using various amines as curing agents

The curing reactions of the epoxy resins tetraglycidyl diaminodiphenyl methane (TGDDM) and tetraglycidyl methylenebis (o-toluidine) (TGMBT) using diaminodiphenyl sulfone (DDS), diaminodiphenyl methane (DDM) and diethylenetriamine (DETA) as curing agents were studied kinetically by differential scanning calorimetry. The dynamic scans in the temperature range 20°–300°C were analyzed to estimate the activation energy and the order of reaction for the curing process using some empirical relations. The activation energy for the various epoxy systems is observed in the range 71.9–110.2 kJ·mol^–1. The cured epoxy resins were studied for kinetics of thermal degradation by thermogravimetry in a static air atmosphere at a heating rate of 10 deg·min^–1. The thermal degradation reactions were found to proceed in a single step having an activation energy in the range 27.6–51.4 kJ·mol^–1.

---

Zusammenfassung Die Vernetzungsreaktionen der Epoxidharze Tetraglycidyl-diamino-diphenyl-methan (TGDDM) und Tetraglycidyl-methylen-bis(o-toluidin) (TGMBT) unter Verwendung von Diaminodiphenylsulfon (DDS), Diaminodiphenylmethan (DDM) und Diethylentriamin (DETA) als Vernetzungsmittel wurden kinetisch mittels DSC untersucht. Die dynamischen Scans im Temperaturbereich 20°–300°C wurden analysiert, um unter Anwendung einiger empirischer Gleichungen die Aktivierungsenergie und die Reaktionsordnung des Vernetzungsprozesses zu ermitteln. Die Aktivierungsenergie der einzelnen Epoxy-Systeme liegt im Bereich 71.9–110.2 kJ·mol^–1. An der ausgehärteten Harze wurde mittels TG in einer statischen Luftatmosphäre un deiner Aufheizgeschwindigkeit von 10 Grad/min die Kinetik des termischen Abbaues untersucht. Man fand, daß die thermiscehn Abbaureaktionen in einem Schritt ablaufen und ihre Aktivierungsenergie im Intervall 27.6–51.4 kJ·mol^–1 liegt.

     

Liquid crystalline epoxides with long lateral substituents: Synthesis and curing

A series of liquid crystalline epoxides with long lateral substituent from 4 to 12 carbon atoms was synthesized and characterized by ¹H NMR, FTIR spectroscopy, differential scanning calorimetry (DSC), polarized light optical microscopy (POM). The curing products of the LCE with DDM, was analyzed by POM and WAXS. The cure kinetics of epoxides and aromatic amine was investigated. The curing activation energy about 43.3-53.2 kJ mol⁻¹ was determined and compared for all the LC epoxides through Ozawa method. The change of activation energy suggests that the reaction active depends upon the lateral substituents, because the lateral substituents parallel to the rod-like core and can act as bound solvent.     

Effect of nanoclays on high and low temperature degradation of fluoroelastomers

High temperature degradation of a fluoroelastomer and its nanocomposites was carried out from room temperature to 700 °C using thermogravimetric analysis (TGA) in nitrogen and oxygen atmospheres. The presence of the unmodified nanoclay enhanced the onset of degradation in both the environments, because of polymer-filler interaction, exfoliation, uniform dispersion and high thermal stability of the layered silicates. In the derivative curve, there was a single T_max, indicating one-stage degradation for all the samples. The non-isothermal activation energy of degradation was determined using the Kissinger and the Flynn-Wall-Ozawa methods. The nanocomposites showed higher activation energy than the neat elastomer. The activation energy of degradation, as observed by isothermal kinetics, was 165, 168 and 177 kJ mol⁻¹ for the neat elastomer, modified and unmodified clay filled samples, respectively. Intrinsic viscosity, measured after low temperature ageing (125-175 °C) showed that the viscosity values were higher for the nanocomposites. The mechanism of degradation is discussed.     

Isoconversional kinetic analysis of stoichiometric and off-stoichiometric epoxy-amine cures

The curing reaction of stoichiometric and off-stoichiometric diglycidyl ether of bisphenol A (DGEBA) and 1,3-phenylene diamine (m-PDA) mixtures was studied by differential scanning calorimetry, thermogravimetric analysis and rheological measurements. In order to highlight the side reactions such as etherification and homopolymerization, the neat DGEBA and DGEBA/DMBA (N,N-dimethylbenzylamine) mixture were examined. The classical model-fitting and the advanced isoconversional methods were used to determine the activation energy of the different reactions. The advanced isoconversional method leads to a good agreement between isothermal, nonisothermal and rheological results. The effective activation energies of primary amine epoxy reaction, etherification and homopolymerization were estimated to about 55-60, 104 and 170 kJ mol⁻¹, respectively.     

Mechanistic modeling of the reaction kinetics of phenyl glycidyl ether (PGE) + aniline using heat flow and heat capacity profiles from modulated temperature DSC

Modulated temperature DSC (MTDSC) has been performed on phenyl glycidyl ether (PGE) + aniline in order to obtain the non-reversing heat flow and heat capacity profiles simultaneously in a wide range of cure temperatures and mixture compositions. The epoxy (PGE) conversion as determined from the former signal corresponds to the one obtained from separate high performance liquid chromatography (HPLC), while the latter signal contains information on the individual reaction steps. Optimized kinetic parameters using a mechanistic approach, including both reactive and non-reactive complexes can successfully simulate MTDSC measurements for isothermal reaction temperatures ranging from 50 to 120 °C and for non-isothermal experiments with mixture compositions corresponding to concentrations of aniline in a range from 1.68 to 6.53 mol kg⁻¹. Concentration profiles for three mixture compositions as obtained from HPLC are also well predicted. The activation energies for the primary amine and secondary amine-epoxy reaction catalyzed by hydroxyl groups are 50 and 52 kJ mol⁻¹, respectively, while the initiation of the reaction corresponds to the primary amine-epoxy reaction catalyzed by primary amine groups with an activation energy of 72 kJ mol⁻¹. A negative substitution effect can be calculated at 0.18 from the ratio of secondary amine to primary amine-epoxy reaction rate constants.     

Calorimetric determination of enthalpy changes for the proton ionization of glycine, N,N-bis(2-hyroxyethyl)glycine (“bicine”) and N-tris(hydroxymethyl)methylglycine (“tricine”) in water-methanol mixtures

Enthalpies for the two proton ionizations of glycine, N,N-bis(2-hyroxyethyl)glycine (“bicine”) and N-tris(hydroxymethyl)methylglycine (“tricine”) were obtained in water-methanol mixtures with methanol mole fraction (X_m) from 0 to 0.360. With increasing methanol the ionization enthalpy for the first proton (ΔH₁) of glycine increased from 4.4 to 9.4 kJ mol⁻¹ with a minimum of 4.1 kJ mol⁻¹ at X_m = 0.059. The ionization enthalpy of the second proton (ΔH₂) for glycine decreased from 46.3 to 38.1 kJ mol⁻¹. ΔH₁ of bicine increased from 3.5 to 7.6 kJ mol⁻¹ at X_m = 0.273 before dropping to 4.1 kJ mol⁻¹ at X_m = 0.360. ΔH₂ of bicine increased from 24.9 to 29.4 kJ mol⁻¹. For tricine, ΔH₁ increased from 6.7 to 9.8 kJ mol⁻¹ at X_m = 0.194 then dropped to 7.4 kJ mol⁻¹ at X_m = 0.360. ΔH₂ for tricine first dropped from 30.8 to 28.5 kJ mol⁻¹ at X_m = 0.059 before increasing to 33.3 kJ mol⁻¹ at X_m = 0.273. The solvent composition was selected so as to include the region of maximum structure enhancement of water by methanol. The results were interpreted in terms of solvent-solvent and solvent-solute interactions.     

Isothermal and polythermal kinetics of depolymerization of C60 polymers

Isothermal depolymerization of the two polymers of C₆₀, i.e. of 1D orthorhombic phase (O) and of “dimer state” (DS) have been studied by means of Infra-red spectroscopy in the temperature ranges 383-423 and 453-503 K, respectively. Differential Scanning Calorimetry (DSC) has been used to obtained depolymerization polytherms for O-phase and DS. Standard set of reaction models have been applied to describe depolymerization behavior of O-phase and DS. The choice of the reaction models was based primarily on the isotherms. Several models however demonstrated almost equal goodness of fit and were statistically indistinguishable. In this case we looked for simpler/more realistic mechanistic model of the reaction. For DS the first-order expression (Mampel equation) with the activation energy E_a = 134 ± 7 kJ mol⁻¹ and preexponential factor ln(A/s⁻¹) = 30.6 ± 2.1, fitted the isothermal data. This activation energy was nearly the same as the activation energy of the solid-state reaction of dimerization of C₆₀ reported in the literature. This made the enthalpy of depolymerization close to zero in accord with the DSC data on depolymerization of DS. Mampel equation gave the best fit to the polythermal data with E_a = 153 kJ mol⁻¹ and preexponential factor ln(A/s⁻¹) = 35.8. For O-phase two reasonable reaction models, i.e. Mampel equation and “contracting spheres” model equally fitted to the isothermal data with E_a = 196 ± 2 and 194 ± 8 kJ mol⁻¹, respectively and ln(A/s⁻¹) = 39.1 ± 0.5 and 37.4 ± 0.2, respectively and to polythermal data with E_a = 163 and 170 kJ mol⁻¹, respectively and ln(A/s⁻¹) = 32.5 and 29.5, respectively.     

Synthesis, heat capacity and enthalpy of formation of [Ho2(l-Glu)2(H2O)8](ClO4)4·H2O

A complex of holmium perchlorate coordinated with l-glutamic acid, [Ho₂(l-Glu)₂(H₂O)₈](ClO₄)₄·H₂O, was prepared with a purity of 98.96%. The compound was characterized by chemical, elemental and thermal analysis. Heat capacities of the compound were determined by automated adiabatic calorimetry from 78 to 370 K. The dehydration temperature is 350 K. The dehydration enthalpy and entropy are 16.34 kJ mol⁻¹ and 16.67 J K⁻¹ mol⁻¹, respectively. The standard enthalpy of formation is −6474.6 kJ mol⁻¹ from reaction calorimetry at 298.15 K.     

Accelerated hydrolytic degradation of Poly(l-lactide)/Poly(d-lactide) stereocomplex up to late stage

Poly(l-lactide) (PLLA)/poly(d-lactide) (PDLA) blend specimens containing only stereocomplex as crystalline species, together with those of pure PLLA and PDLA specimens, were prepared by solution crystallization using acetonitrile as the solvent. Their accelerated hydrolytic degradation was carried out in phosphate-buffered solution at elevated temperatures of 70-97 °C up to the late stage. During hydrolytic degradation, the stereocomplex crystalline residues were first traced by gel permeation chromatography. Similar to the hydrolytic degradation of pure PLLA and PDLA specimens, the hydrolytic degradation of stereocomplexed PLLA/PDLA blend specimens slowed down at the late stage when most of the amorphous chains were removed and crystalline resides were formed and degraded. The estimated activation energy for hydrolytic degradation of stereocomplex crystalline residues (97.3 kJ mol⁻¹) is significantly higher than 75.2 kJ mol⁻¹ reported for α-form of PLLA crystalline residues. This indicates that the stereocomplex crystalline residues showed the higher hydrolysis resistance compared to that of α-form of PLLA crystalline residues.     

Calorimetric determination of enthalpy changes for proton ionization of N-[2-hydroxyethyl]piperazine-N′-[2-ethane sulfonic acid] (HEPES) and N-[2-hydroxyethyl]piperazine-N′-[2-hydroxypropane sulfonic acid] (HEPPSO) in water-methanol mixtures

Enthalpies for the two proton ionizations of the biochemical buffers N-[2-hydroxyethyl]piperazine-N′-[2-ethane sulfonic acid] (HEPES) and N-[2-hydroxyethyl]piperazine-N′-[2-hydroxypropane sulfonic acid] (HEPPSO) were obtained in water-methanol mixtures with methanol mole fraction (X_m) from 0 to 0.360. With increasing methanol, the ionization enthalpy for the first proton (ΔH₁) of HEPES increased steadily from 8.4 to 15.3 kJ mol⁻¹ whereas that for HEPPSO rose to a maximum of 21.0 kJ mol⁻¹ at X_m = 0.123 before dropping to 18.4 kJ mol⁻¹ at X_m = 0.360. The ionization enthalpy for the second proton (ΔH₂) of HEPES varied from 20.8 kJ mol⁻¹ in water to 13.6 kJ mol⁻¹ at X_m = 0.360 with a maximum of 24.8 kJ mol⁻¹ at X_m = 0.194. For HEPPSO, ΔH₂ increased steadily from 23.4 to 29.2 kJ mol⁻¹. The solvent composition was selected so as to include the region of maximum structure enhancement of water by methanol. The results were interpreted in terms of solvent-solvent and solvent-solute interactions.     

Thermodynamic properties of the gaseous barium silicates BaSiO2 and BaSiO3

In the present study, the stability of gaseous barium silicates was confirmed by the high temperature mass spectrometry. On the basis of equilibrium constants measured for gas-phase reactions, the standard formation enthalpies were determined for gaseous barium silicates as (−510 ± 15) kJ · mol⁻¹ and (−884 ± 18) kJ · mol⁻¹ at 298 K; standard atomization enthalpies as (1637 ± 17) kJ · mol⁻¹ and (2318 ± 20) kJ · mol⁻¹ at 298 K for BaSiO₂ and BaSiO₃, respectively. Based on the results obtained the critical analysis of the literature data was carried out.     

Carbon black and propylene oxidation over Ru/CoxMgyAl2Oz catalysts

The effects of Co_xMg_yAl₂O_z mixed oxides composition and ruthenium addition on the oxidation of propylene and carbon black (CB) were investigated. Different reactive cobalt and ruthenium oxide species were formed following calcination at 600 °C. The addition of ruthenium was beneficial for the CB oxidation under “loose contact” conditions and for propylene oxidation when the cobalt content was intermediate to low. The calculated activation energy for CB oxidation was decreased from 151 kJ mol⁻¹ for the uncatalyzed reaction to 111 kJ mol⁻¹ over the best catalyst.     

Kinetic analysis of the thermal stability of lithium silicates (Li4SiO4 and Li2SiO3)

The kinetics describing the thermal decomposition of Li₄SiO₄ and Li₂SiO₃ have been analysed. While Li₄SiO₄ decomposed on Li₂SiO₃ by lithium sublimation, Li₂SiO₃ was highly stable at the temperatures studied. Li₄SiO₄ began to decompose between 900 and 1000 °C. However, at 1100 °C or higher temperatures, Li₄SiO₄ melted, and the kinetic data of its decomposition varied. The activation energy of both processes was estimated according to the Arrhenius kinetic theory. The energy values obtained were −408 and −250 kJ mol⁻¹ for the solid and liquid phases, respectively. At the same time, the Li₄SiO₄ decomposition process was described mathematically as a function of a diffusion-controlled reaction into a spherical system. The activation energy for this process was estimated to be −331 kJ mol⁻¹. On the other hand, Li₂SiO₃ was not decomposed at high temperatures, but it presented a very high preferential orientation after the heat treatments.