Thermoanalytical study of nucleating effects in polypropylene composites

Engineering application of polypropylene requires the employment of flame retardants. Reactive compounding of ammonium-polyphosphate and synergist additives with polypropylene is an effective way for forming flame retardant polypropylene. Both the ammonium-polyphosphate and the additives used for improving its performance effect the crystallization and melting behavior of polypropylene. Encapsulation of flame retardant additives with appropriate elastomer, in order to improve their water resistancy, causes further changes in degree of crystallinity and consequently in the mechanical properties.The financial support of the OTKA 014194 is acknowledged with gratitude.     

Surface treated cellulose fibres in flame retarded PP composites

Polypropylene-based composites were prepared containing non-treated and various treated cotton fibre and wood flakes. A correlation was observed among the fibre treatment and compounding parameters, mechanical and discoloration properties. The structural changes in fibres were demonstrated by Raman spectroscopic and DSC measurements. The possibility for forming cellulose fibre containing flame retardant composites was also investigated. The efficiency of various treatments on compounding, discoloration and mechanical properties enhance in the following order: no treatment < non ionic surfactant < reactive silicone segment containing non ionic surfactant < special silylation treatment. The best results obtained with the special silylation treatment were explained with the more organophilic character and by the thermal stability of the treated fibres. Cellulose fibre as a polyol-charring component and ammonium-polyphosphate together constitute a high performance intumescent flame retardant system in the PP matrix.     

Kinetics and mechanisms of chlorine dioxide and chlorite oxidations of cysteine and glutathione

Chlorine dioxide oxidation of cysteine (CSH) is investigated under pseudo-first-order conditions (with excess CSH) in buffered aqueous solutions, p[H+] 2.7-9.5 at 25.0 degrees C. The rates of chlorine dioxide decay are first order in both ClO2 and CSH concentrations and increase rapidly as the pH increases. The proposed mechanism is an electron transfer from CS- to ClO2 (1.03 x 10(8) M(-1) s(-1)) with a subsequent rapid reaction of the CS* radical and a second ClO2 to form a cysteinyl-ClO2 adduct (CSOClO). This highly reactive adduct decays via two pathways. In acidic solutions, it hydrolyzes to give CSO(2)H (sulfinic acid) and HOCl, which in turn rapidly react to form CSO3H (cysteic acid) and Cl-. As the pH increases, the (CSOClO) adduct reacts with CS- by a second pathway to form cystine (CSSC) and chlorite ion (ClO2-). The reaction stoichiometry changes from 6 ClO2:5 CSH at low pH to 2 ClO2:10 CSH at high pH. The ClO2 oxidation of glutathione anion (GS-) is also rapid with a second-order rate constant of 1.40 x 10(8) M(-1) s(-1). The reaction of ClO2 with CSSC is 7 orders of magnitude slower than the corresponding reaction with cysteinyl anion (CS-) at pH 6.7. Chlorite ion reacts with CSH; however, at p[H+] 6.7, the observed rate of this reaction is slower than the ClO2/CSH reaction by 6 orders of magnitude. Chlorite ion oxidizes CSH while being reduced to HOCl, which in turn reacts rapidly with CSH to form Cl-. The reaction products are CSSC and CSO3H with a pH-dependent distribution similar to the ClO2/CSH system.     

Preparation and properties of metallacyclobutanes of nickel and palladium

Bis(phosphine)-3,3-dimethylnickela- and palladacyclobutanes have been prepared by intramolecular C-H insertion reaction of the corresponding dineopentyl metal complexes. Nickelacyclobutane complexes decompose when heated thereby undergoing competitive carbon-carbon bond cleavage to give isobutene and ethylene, with reductive elimination affording 1,1-dimethylcyclopropane and skeletal isomeri-zation of the metallacyclic ring yielding 3-methyl-1-butene, whereas the palladium analog gave no significant amounts of CC bond cleavage products.Added phos-phine was seen to have an effect on CC bond scission of nickelacyclobutane complexes. Nickelacyclobutane complexes in solution are thought to be in equilibrium with olefin-coordinated nickel-carbene complex on the basis of available experimental evidence from hydrogenolysis, carbene-trap reactions with olefins and reaction with carbon monoxide     

Synthesis and Anti-Hepatocarcinoma Effect of Amino Acid Derivatives of Pyxinol and Ocotillol

Aiming at seeking an effective anti-hepatocarcinoma drug with low toxicity, a total of 24 amino acid derivatives (20 new along with 4 known derivatives) of two active ocotillol-type sapogenins (pyxinol and ocotillol) were synthesized. Both in vitro and in vivo anti-hepatocarcinoma effects of derivatives were evaluated. At first, the HepG2 human cancer cell was employed to evaluate the anti-cancer activity. Most of the derivatives showed obvious enhanced activity compared with pyxinol or ocotillol. Among them, compound 2e displayed the most excellent activity with an IC₅₀ value of 11.26 ± 0.43 µM. Next, H22 hepatoma-bearing mice were used to further evaluate the anti-liver cancer activity of compound 2e. It was revealed that the growth of H22 transplanted tumor was significantly inhibited when treated with compound 2e or compound 2e combined with cyclophosphamide (CTX) (p < 0.05, p < 0.01), and the inhibition rates of tumor growth were 35.32% and 55.30%, respectively. More importantly, compound 2e caused limited damage to liver and kidney in contrast with CTX causing significant toxicity. Finally, the latent mechanism of compound 2e was explored by serum and liver metabolomics based on ultra-performance liquid chromatography quadrupole time-of-flight mass spectrometry (UPLC-QTOF-MS) technology. A total of 21 potential metabolites involved in 8 pathways were identified. These results suggest that compound 2e is a promising agent for anti-hepato-carcinoma, and that it also could be used in combination with CTX to increase efficiency and to reduce toxicity.     

Electron beam modification and crosslinking: Influence of nitrile and carboxyl contents and level of unsaturation on structure and properties of nitrile rubber

The structural changes of nitrile rubber with varying nitrile contents, hydrogenated nitrile rubber and carboxylated nitrile rubber in the presence and absence of a polyfunctional monomer, namely trimethylolpropane triacrylate, at different doses of electron beam irradiation, were investigated with the help of FTIR spectroscopy (in the attenuated total reflectance mode), dynamic mechanical thermal analysis and sol–gel analysis. Solid-state NMR with gated high power decoupling technique was used to understand the mechanism of crosslinking of the irradiated samples. The allylic radicals generated in the butadiene chains react to form intermolecular crosslinkages. There was a significant decrease in the concentration of olefinic groups for the nitrile rubber on irradiation. This was also affirmed by the increase in the carbon resonances due to C–C linkages from the NMR technique, indicating more crosslinkages. The spectroscopic crosslink densities were determined and the results were compared with the swelling measurements. The variation in the crosslink clustering for rubbers with different acrylonitrile contents was explained using the NMR technique. The increase in crosslinking was also revealed by the increase in the percent gel content and dynamic storage moduli with radiation doses. The lifetime of spurs formed and the critical dose, an important criterion for overlapping of spurs, were determined for both the grafted and the ungrafted nitrile rubbers of different grades and compared using a mathematical model. The ratio of scissioning to crosslinking for nitrile rubber was determined using Charlesby–Pinner equation. The mechanical properties had also been studied for both the modified and the unmodified systems.     

Synthesis and modification of silicon nanosheets and other silicon nanomaterials

Silicon nanomaterials and nanostructures exhibit different properties from those of bulk silicon materials based on quantum confinement effects. They are expected to lead to the development of new applications of silicon, in addition to wide use in semiconductor devices. Aside from industrial interest, intriguing issues of academic interest still remain with respect to the origins of their characteristic properties. Zero- and one-dimensional crystalline silicon nanomaterials have been synthesized, to date, by using many methods and there has been rapid progress in size control and modification procedures. However, there have been only a few examples of silicon nanomaterials with atomic-order thickness akin to carbon nanomaterials, such as two-dimensional silicon nanosheets. Moreover, mass production of silicon nanomaterials with relatively low cost is not easily achievable, due to the typically severe conditions required for fabrication, such as high temperature and ultralow pressure. Recently, we have developed a soft synthetic method for silicon nanosheets with chemical surface modification in a solution process. This review provides methods for the synthesis and modification of silicon nanosheets and other silicon nanomaterials with examples of their potential applications.     

扩链剂对脂肪族聚氨酯脲和聚脲弹性体结构与性能的影响

用异佛尔酮二胺(IPDA)、乙二胺(EDA)和己二胺(HDA)三种扩链剂合成了不同结构的脂肪族聚氨酯脲和聚脲, 并考察了扩链剂对聚氨酯脲和聚脲形态结构与性能的影响. 研究结果表明, 与EDA和HDA扩链的聚氨酯脲和聚脲相比, IPDA扩链的聚氨酯脲和聚脲中脲羰基的氢键化程度较低, 软段和硬段间的相混合程度较好; 同时它们具有更好的拉伸强度、硬度和撕裂强度, 但断裂伸长率较低. EDA和HDA扩链的聚氨酯脲和聚脲相比, 两者性能相差不大. 聚氨酯脲的脲羰基较完善氢键化程度以及整个氢键化程度都比聚脲的要低, 同时聚氨酯脲的吸水率也较低.     

Synthesis and characterization of asymmetric polyethersulfone membranes: effects of concentration and polarity of nonsolvent additives on morphology and performance of the membranes

In this study, effects of methanol, ethanol and 1‐propanol as variable nonsolvent additives (NSAs) on the morphology and performance of flat sheet asymmetric polyethersulfone (PES) membranes were investigated. The membranes were prepared from PES/Polyvinylpyrrolidone (PVP)/N‐methyl‐2‐pyrrolidone (NMP) system via phase inversion. The obtained results indicate that with the addition of NSAs to the casting solution, the membrane morphology changes slowly from macrovoids to an asymmetric structure with finger‐like pores. By increasing the NSAs concentrations in the casting solution and decreasing their polarities, the membrane structure changes from finger‐like pores to sponge. The AFM and SEM images reveal that addition of NSA to the casting solution decreases the pore size of the prepared membranes and reduces the pure water flux and BSA solution flux, while increasing the protein rejection. Surface analysis of the membranes showed that mean pore size and surface porosity of the prepared membranes with NSAs in the casting solution are smaller compared with those of the membrane prepared with no NSA. Pure water flux and BSA solution flux through the membranes decrease and BSA rejection increases with increase in the concentration of NSAs and decrease in their polarity. Finally, it can be concluded that the T_g values of the PES membranes increase by addition of NSAs to the casting solution. Copyright © 2009 John Wiley & Sons, Ltd.     

催化材料对病毒的吸附和灭活作用及对哺乳动物细胞的毒性

 提出了以吸附和催化原理灭活病毒的设想，旨在开发出对病毒有过滤、吸附及灭活作用的高效非特异性催化材料，应用于各种防护设施，有效控制非典型肺炎（SARS）的传播．采用与SARS病毒相似的副流感病毒作为模拟对象，进行了吸附及灭活该病毒的催化材料研究，并考察了催化材料对哺乳动物细胞的毒性．结果表明，病毒气溶胶的阻留及吸附结果与基于DNA吸附的色谱分析结果相一致；部分材料可以强烈地吸附病毒（100％），甚至在强烈振荡下并洗脱至第3次，病毒也不能脱附；一些材料不仅可以吸附病毒，而且强烈振荡后的洗脱液虽然表现出一定的血凝效价，但接种鸡胚后，病毒并不增殖，说明材料具有明显的催化病毒灭活性能；对细胞毒性极低的材料可以用在与人体接触的防护材料和设施中．筛选出的性能优异的催化材料，拟进一步考察其对SARS病毒的灭活作用．     

3,5-Dinitrobenzoic acid catalyzed synthesis of 2,3-unsaturated O- and S-glycosides and tetrahydropyranylation of alcohols and phenols

A simple procedure for the synthesis of 2,3-unsaturated glycosides in acetonitrile and tetrahydropyranylation of alcohols and phenols in dichloromethane in the presence of 3,5-dinitrobenzoic acid is described. A variety of alcohols and thiols are reacted with glycals to give the desired products in high yields with high α-selectivity.     

褪黑激素的合成与表征

以吲哚为起始原料,经4步反应合成了褪黑激素(MLT) 吲哚(1)在甲醇中羟基化得到5-羟基吲哚(2),(2)同2-氯乙胺在乙酸乙酯中进行胺乙基化反应得到5-羟基色胺(3),(3)与硫酸二甲酯在甲苯中对羟基进行醚化,得到5-甲氧基色胺(4),(4)经乙酰化得到产物MLT,收率80%     

N-alkylation and N-acylation of polyaniline and its effect on solubility and electrical conductivity

Various alkylating and acylating agents, with different electrophilicity, were allowed to react with polyaniline “emeraldine base” (Pan-EB) or its anion. Replacing the N-hydrogens of polyaniline by various acyl or benzyl groups strongly affected the solubility and the electrical conductivity of the polymer. Neutral Pan-EB was reacted with benzoyl chloride, p-t-butylbenzoyl chloride or pivaloyl chloride in N,N′-dimethylpropylene urea (DMPU) solutions. While the benzoyl and pivaloyl derivatives showed very poor solubility in common organic solvents, the p-t-butylbenzoyl derivative was readily soluble in THF, chloroform, DMSO, etc. As expected, these acyl derivatives showed diminished electrical conductivity relative to that of the parent Pan-EB. Benzyl chlorides did not react with neutral Pan-EB. Attempts to prepare solutions of the nitrogen anion of Pan-EB by reaction with sodium hydride in DMSO or DMPU led invariably to crosslinked insoluble material. This was ascribed to Michael addition of the formed nitrogen anions to the quinonimine moieties. However forming the nitrogen anion in presence of p-t-butylbenzyl chloride trapped it to form N-benzylated Pan-EB. This was a soluble high molecular weight, electrically conductive (4.3 × 10⁻¹ S cm⁻¹ as the hydrochloride) N-alkyl Pan-EB. Reacting Pan-EB with excess of both sodium hydride and benzyl chlorides led to film-forming per-benzylated Pan-leucoemeraldine reduced form. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1673–1679, 1997     

卟啉钴分子筛的制备,表征和催化性能的研究

用液－固相分步合成法将新型四卤四甲基卟啉诱捕在经Ｃｏ＾２＋交换的ＮａＸ分子筛超笼内，利用索式提取器洗净分子筛外表面吸附的卟啉后，采用ＵＶ－Ｖｉｓ、ＩＲ、ＳＥＭ、ＤＴＡ、Ｘ射线衍射分析、吸附等手段对诱捕在超笼内的卟啉予以表征。进一步对比研究了卟啉、分子筛和诱捕卟啉分子筛的催化性能。结果表明，卟啉与分子筛结合后，催化活性大大提高。     

Hydroboration and diimide reduction of caryophyllene and isocaryophyllene

The monohydroboration of caryophyllene with dicyclohexylborane followed by oxidation brought about the participation of the (E)-trisubstituted double bond in preference to the exocyclic double bond during hydroboration to the corresponding unsaturated alcohol. This alcohol gave the corresponding ketone by oxidation. Isocaryophyllene under similar conditions provided the unsaturated alcohol as the major product, wherein the participation of the exocyclic double bond took place during hydroboration. Our attempts to achieve cyclic hydroboration with caryophyllene or isocaryophyllene using thexylborane resulted in the formation of the corresponding unsaturated alcohol. We achieved partial regioselective reduction of caryophyllene and isocaryphyllene with diimide to produce the corresponding dihydroderivative.     

The fate and behavior of glufosinate-enantiomers and their metabolites in open-field soil and weeds

In this study, a chiral method based on high performance liquid chromatography–Q-Exactive Orbitrap Mass Spectrometry was developed to determine glufosinate stereoisomers and three metabolites in weed. Fortified recoveries in weed and soil samples were from 78.6 to 94.3 %, with relative standard deviations of less than 9.8 % and fortified values ranging from 0.04 to 40 mg/kg for the glufosinate enantiomers and 0.08–8 mg/kg for three metabolites. When glufosinate was given at the peak of weed growth in three orchards, it was mostly distributed and degraded in the weeds, with little remaining in the soil. The two glufosinate enantiomers degraded rapidly in the weeds and soils, with half-lives ranging from 0.7 to 3.1 days. The degradation of glufosinate enantiomers in Guizhou and Hunan weeds was enantioselective, with l-glufosinate being preferentially degraded. In Hainan weed, the degradation rate of the two enantiomers was nearly the same. In open field soils, glufosinate enantiomers were almost non-enantioselective. 3-methylphosphinico-propionic acid (MPP) was the primary glufosinate metabolite in weeds and soils, accounting for up to 14 % of the parent. N-acetyl-glufosinate (NAG) was relatively low, with less than 1 % of the parent glufosinate metabolized into 2-methylphosphinico-acetic acid (MPA).     

Electrophoresis and densitometry of serum and urine in the investigation and significance of monoclonal immunoglobulins

About 15% of monoclonal components or paraproteins are associated with malignancy when detected by simple electrophoresis on cellulose acetate membranes or agarose gel followed by protein staining. More sensitive methods for detecting monoclonal components result in a lower frequency of association with recognisable underlying disease. The sensitivity is dependent on the system used. Isoelectric focusing is 10 to 40 times more sensitive than simple electrophoresis at detecting monoclonal components. Electrophoretically separated bands may be quantitated densitometrically and at the present time this is the most satisfactory method for measuring monoclonal component concentration. Immunochemical methods for quantitating monoclonal components are limited by failure to react in a similar manner to polyclonal standards and giving problems of antigen excess resulting both in falsely elevated and low results. Electrophoretic methods must always be used in conjunction with these. The normal polyclonal ratio of immunoglobulin kappa:lambda light chain is disturbed by the presence of a monoclonal component. In 260 patients with myeloma we found that serum electrophoresis alone detected 90% while a disturbance in the kappa:lambda ratio detected 98%. However, 50% of monoclonal components less than 3 g/L were missed. Log kappa:lambda ratio correlates well with the densitometric scan of monoclonal components, both in vitro and in patients being monitored for treatment response in myeloma. This approach may complement or even replace densitometry for this purpose in the future.     

Storage and stability of inorganic and methylmercury solutions

Summary The storage behaviour of mercurychloride and methylmercury chloride solutions in deionized water and in seawater stored in polyethylene (PE), pyrex glass and teflon (PTFE) containers at various concentration levels (4 ppb, 50 ppt, natural seawater concentrations) was studied using various preservatives and container pretreament procedures. For PE bottles, the best results are obtained, after pretreatment of the bottles with an acidified KMnO₄ solution, with a 0.05% (v/v) H₂SO₄+0.02% (w/v) KMnO₄ preservative. However, the solution becomes heterogeneous rather fast, due to the formation of a MnO₂ precipitate. Acidified (pH 1 with HNO₃) deionized or seawater samples stored in pyrex glass BOD-bottles (analyses are carried out in these bottles too) or teflon containers are stable with respect to inorganic mercury for at least 1 month. Instead of acidification an oxidant such as BrCl can also be used to stabilize the solution. Methylmercury solutions (80 ppt) in deionized water (pH 6) and stored in teflon containers are stable for at least 1 month. In glass bottles, the solution should be acidified to pH 1. Methylmercury seems to be unstable in acidified seawater samples (pH 1 with HNO₃); after 2 weeks about 60% of the methylmercury is converted into inorganic mercury.     

茶多酚锰合成、表征及络合和诱导肿瘤细胞凋亡的研究

合成了茶多酚锰(TP-Mn)和茶多酚锗(TP-Ge), 并采用红外光谱法及液相色谱质谱联用技术表征TP-Mn的理化特性. 选用反向液相色谱(RP-HPLC)和电感藕合等离子体质谱(ICP-MS)技术研究牛血清白蛋白(BSA)络合TP-Mn的能力, 指出BSA可直接络合于TP-Mn. 采用MTT法研究TP和TP-Mn诱导Hela卵巢癌细胞的凋亡率. 结果表明, TP和TP-Mn均能诱导Hela卵巢癌细胞凋亡, 但TP-Mn诱导凋亡率约为TP的2倍. 比较TP-Ge和TP-Mn诱导Raji人B淋巴瘤细胞凋亡率发现, 两者诱导肿瘤细胞的凋亡率几乎相同, 均高达86%左右. 人血清白蛋白(HSB)可作为输送TP-Ge和TP-Mn的药物载体.     

Thermal and Spectral Behaviour of 5-chloro-2-methoxybenzoates of Heavy Lanthanides and Yttrium

5-Chloro-2-methoxybenzoates of heavy lanthanides and yttrium were obtained as di- or tetrahydrates with a metal to ligand ratio of 1:3 and general formula: Ln(C₈H₆ClO₃)₃⋅nH₂O, where n=2 for Ln=Tb, Dy, Y and n=4 for Ln=Ho, Er, Tm, Yb, Lu. The complexes were characterized by elemental analysis, IR and FIR spectra, thermogravimetric studies, X-ray diffraction and magnetic measurements. The carboxylate group appears to be a symmetrical, bidentate, chelating ligand. All complexes are polycrystalline compounds. Their thermal stabilities were determined in air and in nitrogen atmospheres. When heated they dehydrate to form anhydrous salts which next in air are decomposed to the oxides of the respective metals while in nitrogen to the mixtures of carbon and oxides or carbon and oxychlorides of respective metals. The complexes are more stable in air than in nitrogen. The solubilities of yttrium and heavy lanthanide 5-chloro-2-methoxybenzoates in water at 293 K are of the order of 10^–3 mol dm^–3 The magnetic moments of the complexes were determined over the range 77–298 K. They obey the Curie–Weiss law. The values of μ_eff calculated for all compounds are close to those obtained for Ln³⁺ by Hund and Van Vleck. The results indicate that there is no influence of the ligand field of 4f electrons on lanthanide ions and the metal ligand bonding is mainly electrostatic in nature. This revised version was published online in August 2006 with corrections to the Cover Date.