Pesticides and degradation products in groundwaters from a vineyard region: Optimization of a multiresidue method based on SPE and GC‐MS

A reliable multiresidue method based on solid phase extraction was developed using GC–MS to determine and quantify 34 pesticides, including herbicides, fungicides, insecticides, and some of their degradation products, in groundwater in a vineyard region of La Rioja (northern Spain). Different parameters were optimized and good recoveries (65–108% range) and precisions (12–19% range) were achieved with spiked water samples for a concentration of 0.1 μg/L. The experimental results showed an excellent linearity (r² > 0.99) over the 0.1–1.5 μg/L range. The detection limits of the proposed method were 1–37 ng/L for most of the compounds studied. The methodology has been successfully applied to the analysis of groundwater samples from vineyard areas in La Rioja and the presence of pesticides, especially fungicides and herbicides, at several concentration levels was revealed. Terbuthylazine, its metabolite desethyl‐terbuthylazine, and fluometuron were the pesticides most frequently detected in higher concentrations. Overall and taking into consideration the European Union maximum residue limit of pesticides in groundwater, 16 of the 34 compounds included in this study were detected in concentrations over that limit in at least one of the samples analyzed.     

Development and validation of a multiresidue method for determination of 82 pesticides in water using GC

Several methods used for the multiresidue analysis of pesticides from the environment and drinking water have been reported. However, most of these reports dealt with a small number of targeted pesticides or some special groups. A method that is simple, faster, and more cost‐effective than the environmental protection agency (EPA) method has been developed for the analysis of 82 frequently used pesticides in water samples obtained from Yeongsan and Sumjin rivers, as well as rice fields located in various locations around the two rivers. The samples were extracted by dichloromethane, and the pesticides were analyzed using a GC‐electron capture detector (ECD), followed by confirmation with GC‐MS. Recoveries were found to be between 82 and 120.1% for most of the tested pesticides, which were in agreement with the standard values dictated by the EPA. The method was potentially applied to 66 water samples for human consumption and 90 water samples from the rice fields and irrigation ditches that were collected from June to September 2007. Oxadiazon, butachlor, and alachlor were detected in some of the river water samples collected in June, iprobenfos (IBP) was detected in samples collected in August, and no pesticide was detected in September. On the other hand, chlorpyrifos‐methyl, IBP, hexaconazole, diazinon, oxadiazon, butachlor, and isoprothiolane were detected at relatively high concentrations in 48 rice paddy field water samples collected between June and September 2007. Alachlor in one sample and procymidone in some of the rice paddy field water samples were also detected in trace amounts. The results were consistent with the temporal pattern of pesticide application in Korean rice fields.     

Multi-residue procedure for the analysis of pesticides in groundwater: Application to samples from the comunidad Valenciana,Spain

Summary A simple multi-residue procedure has been developed and applied to the analysis of pesticides in groundwater samples from the Comunidad Valenciana, a predominantly agricultural area on the Mediterranean coast of Spain. The procedure includes a liquid-liquid extraction, after addition of NaCl on the samples, and a subsequent analysis by capillary gas chromatography using a dual detection system with electron capture and nitrogen-phosphorous detectors. This allows the determination of more than 30 compounds (organophosphorous, organochlorine and pyrethroid pesticides) at the low ppb (g l^–1) levels. Detection limits obtained varied between 0.01 g l^–1 (lindane, fonofos) and 0.5 g l^–1 (cypermethrin). An additional injection of the sample extracts into a gas chromatograph equipped with a column of different polarity and electron capture detector is used for the confirmation of chromatographic peaks. The recommended procedure has been applied to 66 ground water samples. Pesticides, including organophosphorus and organochlorine compounds were detected in 31 of them, in levels ranging from 0.02 to 0.7 g l^–1.     

p-Nitro-N-propylaniline/silica: synthesis, characterization, and its application in matrix solid phase dispersion for multiresidue analysis of pesticides in carrots

A new material for matrix solid phase dispersion (MSPD) was synthesized -- p-nitro-N-propylaniline/silica (pNNPASi) by grafting reactions, characterized by elemental analysis and N(2)-adsorption-desorption isotherms, and tested for multiclass multiresidue analysis of pesticides in wet and freeze-dried carrots. Results obtained applying this new solid phase sorbent to MSPD extraction of ten pesticides (trichlorphon, trifluralin, dicloran, chlorothalonil, prometryn, linuron, captan, procymidone, prochloraz, and deltametrin) in wet carrots showed better results than the ones obtained for freeze-dried samples. Recoveries were in the range of 48-106% and precisions varied from 6 to 20% when wet samples were employed. Comparison between pNNPASi sorbent and C(18) showed better performance of pNNPASi for eight out of ten pesticides tested. The LOQs show that the developed method can be used to detect the pesticides investigated in carrots at concentrations below the maximum residue levels (MRL) established by EU, USEPA, and National Sanitary Surveillance Agency (ANVISA). Linuron, captan, prochloraz, and deltamethrin were found in at least one of the two commercial samples studied in concentrations above the LOQ of this method. Concentrations of the last three pesticides were above the European MRL in one of the commercial samples.     

Supercritical fluid extraction for pesticide multiresidue analysis in honey: determination by gas chromatography with electron-capture and mass spectrometry detection

An analytical procedure using supercritical fluid extraction (SFE) and capillary gas chromatography with electron-capture detection was developed to determine simultaneously residues of different pesticides (organochlorine, organophosphorus, organonitrogen and pyrethroid) in honey samples. Fortification experiments were conducted to test conventional extraction (liquid-liquid) and optimize the extraction procedure in SFE by varying the CO2-modifier, temperature, extraction time and pressure. Best efficiency was achieved at 400 bar using acetonitrile as modifier at 90 degrees C. For the clean-up step, Florisil cartridges were used for both methods LLE and SFE. Recoveries for majority of pesticides from fortified samples of honey at fortification level of 0.01-0.10 mg/kg ranged 75-94% from both methods. Limits of detection found were less than 0.01 mg/kg for ECD and confirmation of pesticide identity was performed by gas chromatography-mass spectrometry in selected-ion monitoring mode. The multiresidue methods in real honey samples were applied and the results of developed methods were compared.     

Comparison of different sorbents for multiresidue solid-phase extraction of 16 pesticides from groundwater coupled with high-performance liquid chromatography

A procedure based on solid-phase extraction (SPE) followed by high-performance liquid chromatography (HPLC) with diode array detection has been developed for the simultaneous analysis of 16 widely used pesticides in groundwater samples. The compounds analysed were: aldicarb, atrazine, desethylatrazine, desysopropylatrazine, carbofuran, 2,4-D, dicloran, fenitrothion, iprodione, linuron, metalaxyl, metazachlor, phenmedipham, procymidone, simazine and vinclozolin. Five different SPE sorbents, C₁₈ bonded silica (Isolute SPE C18 (EC)), graphitised carbon black (Superclean Envi-Carb), highly cross-linked polystyrene-divinylbenzene (Lichrolut EN), divinylbenzene-N-vinylpyrrolidone (Oasis HLB) and surface modified styrene-divinylbenzene (Strata X), were compared. HPLC separation and quantification of the selected pesticides was carried out under isocratic conditions by means of a new reversed-phase column (Gemini from Phenomenex) based on C₁₈ bonded to organic-silica particles. Oasis HLB and Strata X provided the best results in the preconcentration of 1-l samples, yielding average recoveries higher than 70%, except for phenmedipham that rapidly degrades in groundwater. Detection limits of the target pesticides provided by the proposed SPE-HPLC procedure were between 0.003 and 0.04 μg l⁻¹.     

Evaluation of a multiresidue method for measuring fourteen chemical groups of pesticides in water by use of LC-MS-MS

European Council Directive 98/83/EC on the quality of water intended for human consumption brought a new challenge for water-quality control routine laboratories, mainly on pesticides analysis. Under the guidelines of ISO/IEC 17025:2005, a multiresidue method was developed, validated, implemented in routine, and studied with real samples during a one-year period. The proposed method enables routine laboratories to handle a large number of samples, since 28 pesticides of 14 different chemical groups can be quantitated in a single procedure. The method comprises a solid-phase extraction step and subsequent analysis by liquid chromatography-mass spectrometry (LC-MS-MS). The accuracy was established on the basis of participation in interlaboratory proficiency tests, with encouraging results (majority |z-score| <2), and the precision was consistently analysed over one year. The limits of quantitation (below 0.050 μg L⁻¹) are in agreement with the enforced threshold value for pesticides of 0.10 μg L⁻¹. Overall method performance is suitable for routine use according to accreditation rules, taking into account the data collected over one year. Figure Simultaneous SPE extraction system for high thoughput analysis Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users. Notes: IAREN is an accredited laboratory under the ISO/IEC 17025:2005 for 165 analytical determinations and part of the NORMAN Network of Reference laboratories for monitoring of emerging environmental pollutants in the European Union. This work was presented (podium presentation) at the 12th Symposium on Sampling and Handling of the International Association of Environmental Analytical Chemistry (IAEAC), Zaragoza, 2006.     

Liquid chromatography-tandem mass spectrometry determination for multiclass pesticides from insect samples by microwave-assisted solvent extraction followed by a salt-out effect and micro-dispersion purification

The effects of phyto-pharmaceutic compounds (PPCs), such as neonicotinoids, on wildlife reproduction and survival are a rising concern. Yet, understanding the biological consequences of PPC use is particularly complex given the large diversity of PPCs and their derivatives to which wildlife can be exposed. Here, we present a simple and sensitive method for the simultaneous detection and quantification of multiclass PPCs (54 molecules) in single insect boluses (<0.05 g dry mass) by ultra-high pressure liquid chromatography coupled to a tandem mass spectrometer (LC-MS/MS). A key part of this new method is the use of a two-step extraction method combining (i) the high efficiency of a microwave-assisted solvent extraction (MAE) for extracting analytes that might be tightly bound to environmental matrices and (ii) the versatility of a salt-out effect adapted from the QuEChERS methodology allowing the extraction and purification of a wide array of analytes. This microwave-assisted salt-out extraction (MASOE) approach was compared to classical extraction methods including matrix solid phase dispersion (MSPD), microwave-assisted extraction (MAE), and the QuEChERS method. Average recoveries for 54 analytes ranged from 49% to 106%, (relative standard deviations <22%). The limits of detection (LODs) and quantification (LOQs) were in the ranges of 0.10–3.00 ng g⁻¹ and 0.40–7.00 ng g⁻¹, respectively. We applied this method to analyse 881 insect boluses collected from Tree Swallow (Tachycineta bicolour) nestlings along an agricultural intensification gradient in southern Québec (Canada). We detected 25 PPCs out of the 54 considered. We detected at least one PPC in 30% of samples and were able to quantify at least one of them in 17% of samples. Our study shows that the MASOE method should prove to be a powerful tool for studying the fate and impacts of PPCs on wildlife.     

Development and validation of a rapid multiresidue method for pesticide determination using gas chromatography-mass spectrometry: a realistic case in vineyard soils

A rapid and simultaneous method for residue identification and quantification for seven pesticides in agricultural soils has been developed to study a realistic situation in vineyard. The target compounds are two insecticides, two herbicides and three fungicides, from different chemical families. The procedure is based on a pressurized liquid extraction (PLE) with acetone, before a multiresidue GC-MS analysis. The recovery of PLE is between 53.8 ± 2.4 and 99.9 ± 4.4% according to pesticide. A limit of detection (LOD) between 1.4 and 4.6 μg kg⁻¹ of dry soil was obtained for five analytes. This procedure for testing soil contamination is sensitive and easy to perform.     

Study of the effects of operational parameters on multiresidue pesticide analysis by LC-MS/MS

In this paper, the influence of several operational parameters on a well established multiresidue LC-MS/MS method has been studied in relation to the analysis of 150 pesticides commonly present in vegetable samples. The operational parameters investigated are: (i) the influence of different modifiers (0.1% formic acid; 5 mM ammonium formiate; 5 mM ammonium acetate in aqueous phase) - both on the retention time and on the analytical response of the studied compounds; (ii) the effect of the analytical column's temperature on the retention time and on the analytical response of the pesticides investigated; (iii) the effects of co-elution in mixture containing 150 pesticides and, additionally, (iv) the carrying out of a study about the common transitions obtained by LC-MS/MS. Various common transitions were found among the 150 pesticides, but there were only two problematic cases, the pairs diuron-fluometuron and prometryn-terbutryn, which have common scanned transitions and have very close retention times. The use of ammonium salts as modifier instead of formic acid reports enhancement or suppression of the response depending on the pesticides. No great influence on the retention time or on the response of the pesticides and commodities studied was observed with relation to the column temperature. Two different columns: an HPLC (5 μm particle size) and an UHPLC analytical column (1.8 μm particle size) have been used. As was expected, shorter run times and lower peak width was achieved with the UHPLC column.In this paper, the effect of the compounds on each other in the MS analysis when the number of co-eluting compounds is quite high is also described. Mainly small suppression or enhancement co-elution effect was observed, but some particular pesticides presented high sensitivity (>±60% effect) when they elute together with others. This is an important factor and it has to be taken into account when performing multiresidue pesticide analysis.     

Ultra-performance liquid chromatography-tandem mass spectrometry: a novel challenge in multiresidue pesticide analysis in food

Potential of ultra-performance liquid chromatography (UPLC) separation strategy coupled with tandem (in space) mass spectrometric detection (MS/MS) in multiresidue pesticide analysis was critically assessed. Performance parameters such as number of theoretical plates, height of theoretical plate, peak symmetry and peak capacity were measured/calculated on the basis of data generated by analysis of apple extracts containing 17 (semi)polar pesticides representing various classes of active ingredients of widely used crop protective preparations. Ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) procedure provided improved chromatographic parameters resulting in significantly increased sample throughput including lower solvent consumption and lower limits of quantitation (LOQs) for most of target analytes compared to common method employing conventional high-performance liquid chromatography (HPLC) separation.     

Determination of 48 pesticides and their main metabolites in water samples by employing sonication and liquid chromatography-tandem mass spectrometry

In this work, a rapid and sensitive analytical multiresidue method has been developed for the simultaneous determination of 48 pesticides and 19 metabolites in waters (tap, leaching and sewage), using liquid chromatography-tandem mass spectrometry (LC-MS/MS) with triple quadrupole in selected reaction monitoring (SRM) mode. The procedure involves initial single phase extraction of samples with acetonitrile by sonication, followed by liquid-liquid partition aided by “salting out” process using NaCl. Matrix influence on recoveries was evaluated for the three waters. More than 50% of the compound presented very low signal suppression. The method presents good linearity over the range assayed 10-500 μg L⁻¹ and the most frequent detection limits was 0.05 ng mL⁻¹. The average recovery by the LC-MS/MS method obtained for these compounds varied from 74.6 to 111.2% with a relative standard deviation between 2.5 and 8.9%. The proposed method was used to determine pesticides levels in leaching water samples from 5 lysimeters from an experimental greenhouse located in Murcia.     

Multi-residue method for trace pesticide analysis in soils by LC-QQQ-MS/MS and its application to real samples

ABSTRACT

A method for the simultaneous determination of 30 pesticides residues in soil was developed and validated. Among the studied agrochemicals, there are herbicides (auxines, sulfonylureas, fops, imidazolinones), fungicides (azoles) and insecticides (organophosphorus) widely used in extensive agricultural activities in Uruguay. Five methods with different extraction times, type and amount of solvent, as well as the possibility of a clean-up step were compared in terms of percentage of recovery and repeatability. The final method was based on the extraction of the pesticides’ residues from soil using two successive solvent extraction steps. First, the soil was extracted with methanol in an orbital shaker for 4 h. Secondly, the solid residue was re-extracted overnight with ultrapure water. The methanolic extract was concentrated under vacuum, whereas the aqueous solution was passed through an OASIS HLB® cartridge, eluted with an appropriate solvent and concentrated under nitrogen stream. Both extracts were finally combined and analysed by LC-QQQ-MS/MS using the Document SANTE/11,945/2015 criteria. Recovery percentages at 1 and 10 μg kg^?1 for the studied compounds were in the range 70106% with relative standard deviations below 19 %. The quantification was performed using matrix-matched calibration curves as some compounds presented very strong signal suppression. Residuals of the matrix-matched calibration curves were below 20% for all the validated analytes. The quantification limit was1 μg kg^?1. The method also allows the screening of 11 pesticides in soil. Sixty-five real samples collected from regions where the use of pesticides is intensive were analysed. Quinclorac, tebuconazole, penoxsulam and clomazone were the most frequently pesticides detected.     

Application of SPE-HPLC-DAD and SPE-TLC-DAD to the determination of pesticides in real water samples

Planar chromatography with diode array scanning (TLC-DAD) and high-performance chromatography with diode array detection (HPLC-DAD) were used to screen water samples for pesticides. Pesticides were enriched from lake water samples by SPE on C18/SDB-1, C18, C18 Polar Plus and cyanopropyl (CN) cartridges. The recovery rates were high for all extraction materials except for all pesticides on CN cartridges, for which the values were lower. SPE was used not only for preconcentration of analytes but also for their fractionation. The analytes were eluted first with methanol and then with dichloromethane. Methanol eluates were analysed by HPLC-DAD, the dichloromethane eluates with TLC-DAD. The method was validated for precision, repeatability and accuracy. The calibration plots were linear between 0.1 and 50.0 microg/mL for all pesticides, the correlation coefficients, r, were between 0.9992 and 1.000 as determined by HPLC-DAD. In the TLC experiments, the best fit for the calibration lines was found when the calibration data were analysed using a second-degree polynomial regression. Calibration plots lay between 0.1 and 17 microg/spot for all pesticides, the correlation coefficients, r, were between 0.9974 and 0.9997 determined by TLC-DAD. The LOD was between 0.04 and 0.65 microg/spot (TLC-DAD) and between 0.02 and 3.68 microg/mL (HPLC-DAD).     

Multiresidue method for the determination of 13 pesticides in three environmental matrices: water, sediments and fish muscle

Pesticides residues in aquatic ecosystems are an environmental concern which requires efficient analytical methods. In this study, we proposed a generic method for the quantification of 13 pesticides (azoxystrobin, clomazone, diflufenican, dimethachlor, carbendazim, iprodion, isoproturon, mesosulfuron-methyl, metazachlor, napropamid, quizalofop and thifensulfuron-methyl) in three environmental matrices. Pesticides from water were extracted using a solid phase extraction system and a single solid-liquid extraction method was optimized for sediment and fish muscle, followed by a unique analysis by liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS). Limits of quantification were below 5 ng L⁻¹ for water (except for fluroxypyr and iprodion) and ranged between 0.1 ng g⁻¹ and 57.7 ng g⁻¹ for sediments and regarding fish, were below 1 ng g⁻¹ for 8 molecules and were determined between 5 and 49 ng g⁻¹ for the 5 other compounds. This method was finally used as a new routine practice for environmental research.     

Analytical and kinetic study of the aqueous hydrolysis of four organophosphorus and two carbamate pesticides

The hydrolysis of six selected pesticides has been studied in aqueous solution. Four organophosphorus pesticides (disulfoton, isofenfos, isazofos and profenfos) and two N-methylcarbamate derivatives (oxamyl and ethiofencarb) were selected. Hydrolysis was performed in purified buffered water at different pH in the range 7.0–10.0 (ionic strength?=?2.5?mM, T?=?25°C). At pH?=?8.0, isofenfos and disulfoton (t _1/2?≈?4 years, t _1/2?≈?1 year, resp.) were found to be far more stable than isazofos (t _1/2?≈?5 months), ethiofencarb and profenofos (t _1/2<1 month), themselves more stable than oxamyl (t _1/2?≈?1 day). As expected, a strong dependence on pH was observed for all pesticides: the rate of degradation increased when the pH increased. Degradation products were identified by GC–MS and/or LC–MS. Possible structures are presented in the article.     

Multiresidue analysis of 36 pesticides in soil using a modified quick,easy, cheap,effective, rugged,and safe method by liquid chromatography with tandem quadruple linear ion trap mass spectrometry

A new method for simultaneous determination of 36 pesticides, including 15 organophosphorus, six carbamate, and some other pesticides in soil was developed by liquid chromatography with tandem quadruple linear ion trap mass spectrometry. The extraction and clean‐up steps were optimized based on the quick, easy, cheap, effective, rugged, and safe method. The data were acquired in multiple reaction monitoring mode combined with enhanced product ion to increase confidence of the analytical results. Validation experiments were performed in soil samples. The average recoveries of pesticides at four spiking levels (1, 5, 50, and 100 μg/kg) ranged from 63 to 126% with relative standard deviation below 20%. The limits of detection of pesticides were 0.04–0.8 μg/kg, and the limits of quantification were 0.1–2.6 μg/kg. The correlation coefficients (r²) were higher than 0.990 in the linearity range of 0.5–200 μg/L for most of the pesticides. The method allowed for the analysis of the target pesticides in the lower μg/kg concentration range. The optimized method was then applied to the test of real soil samples obtained from several areas in China, confirming the feasibility of the method.     

The application of monolithic columns in pesticides analysis

HPLC and HPLC/MS are the most widely used analytical techniques in the field of pesticides analysis. In recent years, there has been considerable focus on fast separations in HPLC in order to reduce analysis time as well as cost. Monolithic columns, consisting of continuous beds with macropores and mesopores, can meet this requirement and have been widely used in the medical and biological fields. However, it has seldom been used when analyzing pesticides. In this work, the application of monolithic columns in pesticides analysis and their advantages are evaluated and compared with those obtained using conventional packed columns.     

Development, validation and application of a method based on DI-SPME and GC-MS for determination of pesticides of different chemical groups in surface and groundwater samples

A simple and rapid method based on solid-phase micro extraction (SPME) technique followed by gas chromatography-mass spectrometry with selected ion monitoring (GC-MS, SIM) was developed by the simultaneous determination of 16 pesticides of seven different chemical groups [Six organophosphorus (trichlorfon, diazinon, methyl parathion, malathion, fenthion and ethyon), three pyrethroids (bifenhin, permethrin, cypermethrin), two imidazoles (imazalil and prochloraz), two strobilurins (azoxystrobin and pyraclostrobin), one carbamate (carbofuran), one tetrazine (clofentezine), and one triazole (difenoconazole)] in water. The pesticides extraction was done with direct immersion mode (DI-SPME) of the polyacrilate fiber (PA 85 µm). The extraction temperature was adjusted to 50 °C during 30 min, while stirring at 250 rpm was applied. After extraction, the fiber was introduced in the GC injector for thermal desorption for 5 min. at 280 °C. The method was validated using ultra pure water samples fortified with pesticides at different concentration levels and shows good linearity in the concentrations between 0.05 and 250.00 ng mL^− 1. The LOD and LOQ ranged, from 0.02 to 0.30 ng mL^− 1 and 0.05 to 1.00 ng mL^− 1, respectively. Intra-day and inter-day precisions were determined in two concentration levels (5.00 and 50.00 ng mL^− 1). Intra-day relative standard deviation (%R.S.D.) ranged between 3.6 and 13.6%, and inter-day (%R.S.D.) ranged between 6.3 and 18.5%. Relative recovery tests were carried out spiking the ultra pure sample with standards in three different concentration levels 0.20, 5.00 and 50.00 ng mL^− 1. The recovery at 0.20 ng mL^− 1 level varied from 86.4 ± 9.4% to 108.5 ± 10.5%, at 5.00 ng mL^− 1 level varied from 77.5 ± 10.8% to 104.6 ± 9.6% and at 50.00 ng mL^− 1 level varied from 70.2 ± 4.6% to 98.4 ± 8.5%. The proposed SPME method was applied in twenty-six water samples collected in the “Platô de Neópolis”, State of Sergipe, Brazil. Methyl parathion was detected in five samples with an average concentration of 0.17 ng mL^− 1 and bifenthrin, pyraclostrobin and azoxystrobin residues were found in three samples with average concentrations of 2.28, 3.12 and 0.15 ng mL^− 1, respectively.     

Gas chromatographic method for studying the rate of photodegradation of some nitrogen-containing pesticides

Summary The photodegradation behaviour of 12 nitrogen-containing herbicides (atrazine, cyanazine, terbuthylazine, terbutryn, EPTC, buthylate, molinate, cycloate, vernolate, fenuron, chloroxuron, and methabenzthiazuron) has been examined. The compounds were degraded completely when exposed to a mercury-vapour lamp; the degradation process was followed by consecutive GC measurements. All the compounds studied had measurable photochemical activity, although actual and average degradation rates varied significantly. All the compounds except terbutryn furnished more than one major degradation product, in different ratios. Presented at Balaton Symposium '01 on High-Performance Separation Methods, Siófok, Hungary, September 2–4, 2001