Comparison of Cadmium Cd2+ and Lead Pb2+ Binding by Fe2O3@SiO2‐EDTA Nanoparticles – Binding Stability and Kinetic Studies

This study describes the synthesis and characterization of ethylenediaminetetraacetic acid (EDTA) functionalized magnetic nanoparticles of 20 nm in size – Fe₃O₄@SiO₂‐EDTA – which were used as a novel magnetic adsorbent for Cd(II) and Pb(II) binding in aqueous medium. These nanoparticles were obtained in two‐stage synthesis: covering by tetraethyl orthosilicate and functionalization with EDTA derivatives. Nanoparticles were characterized using TEM, FT‐IR, and XPS methods. Metal ions were detected under optimized experimental conditions using Differential Pulse Anodic Stripping Voltammetry (DPASV) and Hanging Mercury Drop Electrode (HDME) techniques. We compared the ability of Fe₃O₄@SiO₂‐EDTA to bind cadmium and lead in concentration of 553.9 μg L^?1 and 647.5 μg L^?1, respectively. Obtained results show that the adsorption rate of cadmium binding was very high. The equilibrium for Fe₃O₄@SiO₂‐EDTA‐Cd(II) was reached within 19 min while for the Fe₃O₄@SiO₂‐EDTA‐Pb(II) was reached within 25 minutes. About 2 mg of nanoparticles was enough to bind 87.5 % Cd(II) and 54.1 % Pb(II) content. In the next step the binding capacity of Fe₃O₄@SiO₂‐EDTA nanoparticles was determined. Only 1.265 mg of Fe₃O₄@SiO₂‐EDTA was enough to bind 96.14 % cadmium ions while 5.080 mg of nanoparticles bound 40.83 % lead ions. This phenomenon proves that the studied nanoparticles bind Cd(II) much better than Pb(II). The cadmium ions binding capacity of Fe₃O₄@SiO₂‐EDTA nanoparticles decreased during storage in 0.5 M KCl solution. Two days of Fe₃O₄@SiO₂‐EDTA storage in KCl solution caused the 32 % increase in the amount of nanoparticles required to bind 60 % of cadmium while eight‐days storage caused further increase to 328 %. The performed experiment confirmed that the storage of nanoparticles in solution without any surfactants reduced their binding capacity. The best binding capacity was observed for the nanoparticles prepared directly before the electrochemical measurements.     

Adsorption of acid red 114 and reactive black 5 in aqueous solutions on dendrimer‐conjugated magnetic nanoparticles

The adsorption of the dyes Acid Red 114 and Reactive Black 5 in aqueous solutions on polyhydroxyl dendrimer magnetic nanoparticles (Fe₃O₄@SiO₂‐TRIS) was studied in a batch system. The Fe₃O₄@SiO₂‐TRIS NPs were characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, and transmission electron microscopy. Experiments were performed under different conditions such as the initial dye concentration, adsorbent dose, and pH. The pseudo‐second‐order model provided a very good fit for the two anionic dyes. The Langmuir and Freundlich adsorption models were used to describe the equilibrium isotherms at different temperatures, and the former agreed very well with the experimental data. However, the adsorption capacity of Fe₃O₄@SiO₂‐TRIS NPs was reduced during surface modification, which could be due to the dye occupying the binding sites of the dendrimer. Thermodynamic parameters, namely the change in free energy (ΔG⁰), enthalpy (ΔH⁰), and entropy (ΔS⁰), were also determined.     

Carboxymethylated polyethylenimine modified magnetic nanoparticles specifically for purification of His‐tagged protein

Employing immobilized metal‐ion affinity chromatography and magnetic separation could ideally provide a useful analytical strategy for purifying His‐tagged protein. In the current study, a facile route was designed to prepare CMPEI‐Ni²⁺@SiO₂@Fe₃O₄ (CMPEI=carboxymethylated polyethyleneimine) magnetic nanoparticles composed of a strong magnetic core of Fe₃O₄ and a Ni²⁺‐immobilized carboxymethylated polyethyleneimine coated outside shell, which was formed by electrostatic interactions between polyanionic electrolyte of carboxymethylated polyethyleneimine and positively charged surface of 3‐(trimethoxysilyl)propylamin modified SiO₂@Fe₃O₄. The resulting CMPEI‐Ni²⁺@SiO₂@Fe₃O₄ composite nanoparticles displayed well‐uniform structure and high magnetic responsiveness. Hexa His‐tagged peptides and purified His‐tagged recombinant retinoid X receptor alpha were chosen as the model samples to evaluate the adsorption, capacity, and reusability of the composite nanoparticles. The results demonstrated the CMPEI‐Ni²⁺@SiO₂@Fe₃O₄ nanoparticles possessed rapid adsorption, large capacity, and good recyclability. The obtained nanoparticles were further used to purify His‐tagged protein in practical environment. It was found that the nanoparticles could selectively capture His‐tagged recombinant retinoid X receptor protein from complex cell lysate. Owing to its easy synthesis, large binding capacity, and good reusability, the prepared CMPEI‐Ni²⁺@SiO₂@Fe₃O₄ magnetic nanoparticles have great potential for application in biotechnological fields.     

Molecularly imprinted polymer functionalized magnetic Fe3O4 for the highly selective extraction of triclosan

We present a facile strategy to prepare the molecularly imprinted polymers layer on the surface of Fe₃O₄ nanoparticles with core‐shell structure via sol–gel condensation for recognition and enrichment of triclosan. The Fe₃O₄ nanoparticles were first synthesized by a solvothermal method. Then, template triclosan was self‐assembled with the functional monomer 3‐aminopropyltriethoxysilane on the silica‐coated Fe₃O₄ nanoparticles in the presence of ethanol and water. Finally, the molecularly imprinted polymers were formed on the surface of silica‐coated Fe₃O₄ nanoparticles to obtain the product. The morphology, magnetic susceptibility, adsorption, and recognition property of magnetic molecularly imprinted polymers were characterized using transmission electron microscopy, Fourier transform infrared spectroscopy, X‐ray diffractometry, vibrating sample magnetometry, and re‐binding experiments. The magnetic molecularly imprinted polymers showed binding sites with good accessibility, fast adsorption rate, and high adsorption capacity (218.34 μg/g) to triclosan. The selectivity of magnetic molecularly imprinted polymers was evaluated by the rebinding capability of triclosan and two other structural analogues (phenol and p‐chlorophenol) in a mixed solution and good selectivity with an imprinting factor of 2.46 was obtained. The application of triclosan removal in environmental samples was demonstrated.     

Preparation of core–shell structure Fe3O4@SiO2 superparamagnetic microspheres immoblized with iminodiacetic acid as immobilized metal ion affinity adsorbents for His‐tag protein purification

The core–shell structure Fe₃O₄/SiO₂ magnetic microspheres were prepared by a sol–gel method, and immobiled with iminodiacetic acid (IDA) as metal ion affinity ligands for protein adsorption. The size, morphology, magnetic properties and surface modification of magnetic silica nanospheres were characterized by various modern analytical instruments. It was shown that the magnetic silica nanospheres exhibited superparamagnetism with saturation magnetization values of up to 58.1 emu/g. Three divalent metal ions, Cu²⁺, Ni²⁺ and Zn²⁺, were chelated on the Fe₃O₄@SiO₂–IDA magnetic microspheres to adsorb lysozyme. The results indicated that Ni²⁺‐chelating magnetic microspheres had the maximum adsorption capacity for lysozyme of 51.0 mg/g, adsorption equilibrium could be achieved within 60 min and the adsorbed protein could be easily eluted. Furthermore, the synthesized Fe₃O₄@SiO₂–IDA–Ni²⁺ magnetic microspheres were successfully applied for selective enrichment lysozyme from egg white and His‐tag recombinant Homer 1a from the inclusion extraction expressed in Escherichia coli. The result indicated that the magnetic microspheres showed unique characteristics of high selective separation behavior of protein mixture, low nonspecific adsorption, and easy handling. This demonstrates that the magnetic silica microspheres can be used efficiently in protein separation or purification and show great potential in the pretreatment of the biological sample. Copyright © 2015 John Wiley & Sons, Ltd.     

Monomer Protonation‐Dependent Surface Polymerization to Achieve One‐Step Grafting Cross‐Linked Poly(4‐Vinylpyridine) Onto Core–Shell Fe3O4@SiO2 Nanoparticles

Functional polymer‐grafting silica nanoparticles hold great promise in diverse applications such as molecule recognition, drug delivery, and heterogeneous catalysis due to high density and uniform distribution of functional groups and their tunable spatial distance. However, conventional grafting methods from monomers mainly consist of one or more extra surface modification steps and a subsequent surface polymerization step. A monomer protonation‐dependent surface polymerization strategy is proposed to achieve one‐step uniform surface grafting of cross‐linked poly(4‐vinylpyridine) (P4VP) onto core–shell Fe₃O₄@SiO₂ nanostructures. At an approximate pH, partially protonated 4VP sites in aqueous solution can be strongly adsorbed onto deprotonated silanol groups ( Si O⁻) onto Fe₃O₄@SiO₂ nanospheres to ensure prior polymerization of these protonated 4VP sites exclusively onto Fe₃O₄@SiO₂ nanoparticles and subsequent polymerization of other 4VP and divinylbenzene monomers harvested by these protonated 4VP monomers onto Fe₃O₄@SiO₂ nanoparticles, thereby achieving direct grafting of cross‐linked P4VP macromolecules onto Fe₃O₄@SiO₂ nanoparticles.     

Carbazole‐based conjugated polymer covalently coated Fe3O4 nanoparticle as efficient and reversible Hg2+ optical probe

A type of fluorescent–magnetic dual‐function nanocomposite, Fe₃O₄@SiO₂@P‐2, was successfully obtained by Cu⁺‐catalyzed click reaction between acetylene (C?C? H)‐substituted carbazole‐based conjugated polymer ( P‐2) and azide‐terminated silica‐coated magnetic iron oxide nanoparticles (Fe₃O₄@SiO₂–N₃). Optical and magnetization analyses indicate that Fe₃O₄@SiO₂@P‐2 exhibits stable fluorescence and rapid magnetic response. The fluorescence of Fe₃O₄@SiO₂@P‐2 was quenched significantly in the presence of I^? and gave a detection limit (DL) of ～8.85 × 10^?7 M. Given the high binding constant and matching ratio between Hg²⁺ and I^?, the fluorescence of Fe₃O₄@SiO₂@P‐2/I^? complex recovered efficiently with the addition of Hg²⁺. A DL of ～4.17 × 10^?7 M was obtained by this probing system. Recycling of Fe₃O₄@SiO₂@P‐2 probe was readily achieved by simple magnetic separation. Results indicate that Fe₃O₄@SiO₂@P‐2 can be used as an “on–off–on” fluorescent switchable and recyclable Hg²⁺ probe. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3636–3645     

Synthesis,characterization and application of sulfonic acid supported on ferrite–silica superparamagnetic nanoparticles

In this study, the synthesis of sulfonic acid supported on ferrite–silica superparamagnetic nanoparticles (Fe₃O₄@SiO₂@SO₃H) as a nanocatalyst with large density of acidic groups is suggested. This nanocatalyst was prepared in three steps: preparation of colloidal iron oxide magnetic nanoparticles (Fe₃O₄ MNPs), coating of silica on Fe₃O₄ MNPs (Fe₃O₄@SiO₂) and incorporation of sulfonic acid as a functional group on the surface of Fe₃O₄@SiO₂ nanoparticles (Fe₃O₄@SiO₂@SO₃H). The properties of the prepared magnetic nanoparticles were characterized using transmission electron microscopy, infrared spectroscopy, vibrating sample magnetometry, X‐ray diffraction and thermogravimetric analysis. Finally, the applicability of the synthesized magnetic nanoparticles was tested as a heterogeneous solid acid nanocatalyst for one‐pot synthesis of diindolyloxindole derivatives in aqueous medium. Oxindole derivatives were produced by the coupling of indole and isatin compounds with good to high yields (60–98%). Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation of novel palladium nanoparticles supported on magnetic iron oxide and their catalytic application in the synthesis of 2‐imino‐3‐phenyl‐2,3‐dihydrobenzo[d]oxazol‐5‐ols

Novel Pd nanoparticles were prepared in five successive stages: 1) preparation of the Fe₃O₄ magnetic nanoparticles (Fe₃O₄ MNPs), 2) coating of Fe₃O₄ MNPs with SiO₂ (Fe₃O₄@SiO₂), 3) functionalization of Fe₃O₄@SiO₂ with 3‐chloropropyltrimethoxy‐ silane (CPTMS) ligand (Fe₃O₄@SiO₂@CPTMS), 4) further functionalization with 3,5‐diamino‐1,2,4‐triazole (DAT) ligand (Fe₃O₄@SiO₂@CPTMS @DAT), and 5) the complexation of Fe₃O₄@SiO₂@CPTMS@DAT with PdCl₂ (Fe₃O₄@SiO₂@CPTMS@ DAT@Pd). Then, the obtained Pd nano‐catalyst characterized by different methods such as the elemental analysis (CHN), FT‐IR, XRD, EDX, SEM, TEM, TG‐DTA and VSM. Finally, the Pd catalyst was applied for the synthesis of various 2‐imino‐3‐phenyl‐2,3‐dihydrobenzo[d]oxazol‐5‐ols.     

Improvement on physical properties of polyethersulfone membranes modified by poly(1‐vinylpyrrolidone) grafted magnetic Fe3O4@SiO2 nanoparticles

Polyethersulfone (PES) and poly(1‐vinylpyrrolidone) (PVP) were used to prepare ultrafiltration membranes with grafted Fe₃O₄ magnetic nanoparticles (PVP‐g‐Fe₃O₄@SiO₂). The structure of synthesized PVP‐g‐Fe₃O₄@SiO₂ was confirmed by FT‐IR and SEM analysis. Physical properties of blend membranes such as thermal resistance, Tensile strength, water uptake, and hydrophilicity were also investigated. Blended membranes of PES/PVP‐g‐Fe₃O₄@SiO₂ have exhibited higher thermal resistance due to increasing the modified nanoparticle content. The hydrophilicity of the synthesized PES/PVP‐g‐Fe₃O₄@SiO₂ membranes also improved by increasing the PVP‐g‐Fe₃O₄@SiO₂ content. As expected, increasing the hydrophilicity of blended membrane, caused enhancement of fouling resistance in membranes. Results showed that the content of PVP‐g‐Fe₃O₄@SiO₂ has different effects on the properties of synthesized composite membranes. Despite increasing the content of PVP‐g‐Fe₃O₄@SiO₂ has a negative effect on elongation, positive effects on maximum stress was observed. Moreover, the water uptake of synthesized membranes was significantly enhanced in comparison to other similar studies.     

Preparation and application of magnetic molecularly imprinted polymers for the isolation of chelerythrine from Macleaya cordata

A novel type of magnetic molecularly imprinted polymer was prepared for the selective enrichment and isolation of chelerythrine from Macleaya cordata (Willd) R. Br. The magnetic molecularly imprinted polymers were prepared using functional Fe₃O₄@SiO₂ as a magnetic support, chelerythrine as template, methacrylic acid as functional monomer, and ethylene glycol dimethacrylate as cross‐linker. Density functional theory at the B3LYP/6‐31G (d, p) level with Gaussian 09 software was applied to calculate the interaction energies of chelerythrine, methacrylic acid and the complexes formed from chelerythrine and methacrylic acid in different ratios. The structural features and morphology of the synthesized polymers were characterized by using Fourier transform infrared spectroscopy, X‐ray diffraction, transmission electron microscopy, and vibration sample magnetometry. Adsorption experiments revealed that the magnetic molecularly imprinted polymers possessed rapid kinetics, high selectivity, and a higher binding capacity (7.96 mg/g) to chelerythrine than magnetic molecularly non‐imprinted polymers (2.36 mg/g). The adsorption process was in good agreement with the Langmuir adsorption isotherm and pseudo‐second‐order kinetics models. Furthermore, the magnetic molecularly imprinted polymers were successfully employed as adsorbents for the extraction and enrichment of chelerythrine from Macleaya cordata (Willd) R. Br. The results indicated that the magnetic molecularly imprinted polymers were suitable for the selective adsorption of chelerythrine from complex samples such as natural medical plants.     

Butane‐1‐sulfonic acid immobilized on magnetic Fe3O4@SiO2 nanoparticles: A novel and heterogeneous catalyst for the one‐pot synthesis of barbituric acid and pyrano[2,3‐d] pyrimidine derivatives in aqueous media

Butane‐1‐sulfonic acid immobilized on magnetic Fe₃O₄@SiO₂ nanoparticles (Fe₃O₄@SiO₂‐Sultone) was easily prepared via direct ring opening of 1,4‐butanesultone with nanomagnetic Fe₃O₄@SiO₂. The prepared reagent was characterized and used for the efficient promotion of the synthesis of barbituric acid and pyrano[2,3‐d] pyrimidine derivatives. All reactions were performed under mild and completely heterogeneous reaction conditions affording products in good to high yields. The catalyst is easily isolated from the reaction mixture by magnetic decantation and can be reused at least eight times without significant loss in activity.     

One‐pot synthesis of 1‐ and 5‐substituted 1H‐tetrazoles using 1,4‐dihydroxyanthraquinone–copper(II) supported on superparamagnetic Fe3O4@SiO2 magnetic porous nanospheres as a recyclable catalyst

An effective one‐pot, convenient process for the synthesis of 1‐ and 5‐substituted 1H‐tetrazoles from nitriles and amines is described using1,4‐dihydroxyanthraquinone–copper(II) supported on Fe₃O₄@SiO₂ magnetic porous nanospheres as a novel recyclable catalyst. The application of this catalyst allows the synthesis of a variety of tetrazoles in good to excellent yields. The preparation of the magnetic nanocatalyst with core–shell structure is presented by using nano‐Fe₃O₄ as the core, tetraethoxysilane as the silica source and poly(vinyl alcohol) as the surfactant, and then Fe₃O₄@SiO₂ was coated with 1,4‐dihydroxyanthraquinone–copper(II) nanoparticles. The new catalyst was characterized using Fourier transform infrared spectroscopy, X‐ray diffraction, transmission electron microscopy, field emission scanning electron microscopy, dynamic light scattering, thermogravimetric analysis, vibration sample magnetometry, X‐ray photoelectron spectroscopy, nitrogen adsorption–desorption isotherm analysis and inductively coupled plasma analysis. This new procedure offers several advantages such as short reaction times, excellent yields, operational simplicity, practicability and applicability to various substrates and absence of any tedious workup or purification. In addition, the excellent catalytic performance, thermal stability and separation of the catalyst make it a good heterogeneous system and a useful alternative to other heterogeneous catalysts. Also, the catalyst could be magnetically separated and reused six times without significant loss of catalytic activity. Copyright © 2016 John Wiley & Sons, Ltd.     

Multi‐walled carbon nanotube modified dummy‐template magnetic molecularly imprinted microspheres as solid‐phase extraction material for the determination of polychlorinated biphenyls in fish

Novel multi‐walled carbon nanotube modified dummy‐template molecularly imprinted microspheres (MWCNTs@DMMIPs) were successfully synthesized as adsorbents for six kinds of polychlorinated biphenyls (PCBs). MWCNTs@DMMIPs were prepared by a surface molecular imprinting technique. Core–shell Fe₃O₄@SiO₂ nanoparticles were employed as magnetic support. 3,4‐Dichlorobenzene acetic acid was used as a dummy template instead of PCBs, methacrylic acid was used as functional monomer and ethylene glycol dimethacrylate was used as the cross‐linker. The resulting absorbent was characterized by various methods. The adsorbent was employed for extracting PCBs and exhibited good selectivity and high adsorption efficiency. Furthermore, it was reusable and capable of magnetic separation. Adsorption kinetics fit well with a pseudo‐second‐order kinetic equation and also exhibited a three‐stage intra‐particle diffusion model. The Freundlich model was used to describe the adsorption isotherms. The materials were successfully applied to the magnetic dispersive solid‐phase extraction of six kinds of PCBs followed by gas chromatography with mass spectrometry determination in fish samples, the limit of detection of six kinds of PCBs were 0.0028–0.0068 μg/L and spiked recoveries ranged between 73.41 and 114.21%. The prepared adsorbent was expected to be a new material for the removal and recovery of PCBs from contaminated foods.     

Synthesis of Fe3O4@SiO2-Au/Cu magnetic nanoparticles and its efficient catalytic performance for the Ullmann coupling reaction of bromamine acid

Over bimetallic Au/Cu catalyst supported on magnetic Fe₃O₄ nanoparticles, water-mediated bromamine acid could be selectively converted into 4,4'-diamino-1,1'-dianthraquinonyl-3,3'-disulfonic acid (DAS) with a yield of 88.67%. The magnetic catalyst could be readily separated and reused.     

Synthesis and characterization of Fe3O4@SiO2–polymer-imid–Pd magnetic porous nanospheres and their application as a novel recyclable catalyst for Sonogashira–Hagihara coupling reactions

We demonstrate herein the modification of magnetic nanoparticles and their use as a magnetic nanocatalyst in direct coupling reactions of aryl halides with terminal alkynes. Magnetite particles were prepared by simple co-precipitation method in aqueous medium, and then Fe₃O₄@ SiO₂ nanosphere was synthesized by using nano-Fe₃O₄ as the core, TEOS as the silica source and PVA as the surfactant. Fe₃O₄@SiO₂ was coated with polymeric N-heterocyclic carbene/Pd. The samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy, field emission scanning electron microscopy, dynamic light scattering, thermogravimetric analysis, vibration sample magnetometer and N₂ adsorption–desorption isotherm analysis. Poly (N-vinyl imidazole) functionalized Fe₃O₄@SiO₂ nanoparticle was found to be an efficient nanocatalyst in Sonogashira–Hagihara cross-coupling reactions. The nanocatalyst can be easily recovered by a magnetic field and reused for six runs without appreciable loss of its catalytic activity.     

Synthesis of a highly active amino‐functionalized Fe3O4@SiO2/APTS/Ru magnetic nanocomposite catalyst for hydrogenation reactions

An amino‐functionalized silica‐coated Fe₃O₄ nanocomposite (Fe₃O₄@SiO₂/APTS) was synthesized. The Fe₃O₄@SiO₂ microspheres possessed a well‐defined core–shell structure, uniform sizes and high magnetization. An immobilized ruthenium nanoparticle catalyst (Fe₃O₄@SiO₂/APTS/Ru) was obtained after coordination and reduction of Ru³⁺ on the Fe₃O₄@SiO₂/APTS nanocomposite. The Ru nanoparticles were not only ultra‐small with nearly monodisperse sizes but also had strong affinity with the surface of Fe₃O₄@SiO₂/APTS. The obtained catalyst exhibited excellent catalytic performance for the hydrogenation of a variety of aromatic nitro compounds, even at room temperature. Moreover, Fe₃O₄@SiO₂/APTS/Ru was easily recovered using a magnetic field and directly reused for at least five cycles without significant loss of its activity.     

Sulfonated magnetic nanocatalyst and application for synthesis of novel Spiro[acridine-9,5′-thiazole]-1,4′-dione derivatives

Sulfonated Sulfurol supported Fe₃O₄ (Fe₃O₄@SiO₂-Pr-Sulfurol-SO₃H) a new magnetic reusable nanocatalyst was prepared using chemical modification of magnetic nanoparticles (MNPs) surface with Sulfurol-SO₃H. The Sulfurol-SO₃H moieties on the surface of MNPs act as acidic catalytic sites for catalysis purposes. Fe₃O₄@SiO₂-Pr-Sulfurol-SO₃H was authenticated by usual analytical and spectroscopic techniques. The prepared Fe₃O₄@SiO₂-Pr-Sulfurol-SO₃H MNPs were applied to the preparation of novel Spiro[acridine-9,5′-thiazole]-1,4′-dione derivatives via the three-component condensation of isatins, dimedone and thioamides or thioureas.

     

Hiyama cross‐coupling reaction using Pd(II) nanocatalyst immobilized on the surface of Fe3O4@SiO2

We report a simple process for the synthesis of Fe₃O₄@SiO₂/APTMS (APTMS = 3‐aminopropyltrimethoxysilane) core–shell nanocatalyst support. The new nanocatalyst was prepared by stabilization of Pd(cdha)₂ (cdha = bis(2‐chloro‐3,4‐dihydroxyacetophenone)) on the surface of the Fe₃O₄@SiO₂/APTMS support. The structure and composition of this catalyst were characterized using various techniques. An efficient method was developed for the synthesis of a wide variety of biaryl compounds via fluoride‐free Hiyama cross‐coupling reactions of aryl halides with arylsiloxane, with Fe₃O₄@SiO₂/APTMS/Pd(cdha)₂ as the catalyst under reaction conditions. This methodology can be performed at 100°C through a simple one‐pot operation using in situ generated palladium nanoparticles. High catalytic activity, quick separation of catalyst from products using an external magnetic field and use of water as green solvent are attributes of this protocol.     

Highly selective and recyclable hydrogenation of α‐pinene catalyzed by ruthenium nanoparticles loaded on amphiphilic core–shell magnetic nanomaterials

A multifunctional nanomaterial (Fe₃O₄@SiO₂@C_X@NH₂) comprising a magnetic core, a silicon protective interlayer, and an amphiphilic silica shell is successfully prepared. Ru nanoparticles catalyst loaded on Fe₃O₄@SiO₂@C_X@NH₂ is used in hydrogenation of α‐pinene for the first time. The novel nanomaterial with amphipathy can be used as a solid foaming agent to increase gas–liquid–solid three‐phase contact and accelerate the reaction. Under the mild conditions (40 °C, 1 MPa H₂, 3 h), 99.9% α‐pinene conversion and 98.9% cis‐pinane selectivity are obtained, which is by far the best results reported. Furthermore, the magnetic nanocomposite catalyst can be easily separated by an external magnet and reused nine times with high selectivity maintaining.