Optimization strategies for radiation induced grafting of 4-vinylpyridine onto poly(ethylene-co-tetraflouroethene) film using Box-Behnken design

The radiation induced grafting of 4-vinylpyridine (4-VP) onto poly(ethylene-co-tetrafluoroethene) (ETFE) was optimized using the Box-Behnken factorial design available in the response surface method (RSM). The optimized grafting parameters; absorbed dose, monomer concentration, grafting time and reaction temperature were varied in four levels to quantify their effect on the grafting yield (GY). The validity of the statistical model was supported by the small deviation between the predicted (GY=61%) and experimental (GY=57%) values. The optimum conditions for enhancing GY were determined at the following values: monomer concentration of 48 vol%, absorbed dose of 64 kGy, reaction time of 4 h and temperature of 68 °C. A comparison was made between the optimization model developed for the present grafting system and that for grafting of 1-vinylimidazole (1-VIm) onto ETFE to confirm the validly and reliability of the Box-Behnken for the optimization of various radiation induced grafting reactions. Fourier transform infrared (FTIR), thermogravimetric analysis (TGA) and X-ray diffraction (XRD) were used to investigate the properties of the obtained films and provide evidence for grafting.     

Effect of zinc salts on the spontaneous copolymerization of 4-vinylpyridine with various electron-rich vinyl monomers

The spontaneous copolymerization of 4-vinylpyridine (4-VP) complexed with three different zinc salts (chloride, acetate, and triflate) with various electron-rich vinyl monomers (p-methoxystyrene, MeOSt; p-methylstyrene, MeSt; α-methylstyrene, α-MeSt; p-tert-butylstyrene, BuSt; styrene, St) was investigated in methanol at 75°C. Increasing the zinc salt concentration or the nucleophilicity of the electron-rich monomer increased the copolymer yields. All obtained copolymers are characterized by high molecular weight (10⁵) and broad molecular weight distribution. Both ¹H-NMR and elemental analyses confirmed the almost 1 : 1 copolymer structure. Changing the anion of the zinc salt does not have a considerable effect either on the copolymerization rate or on the molecular weight. The proposed mechanism exhibits the formation of a σ-bond between the β-carbons of the two donor–acceptor monomers. This creates the 1,4-tetramethylene biradical intermediate which can initiate the copolymerization reaction. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2787–2792, 1997     

Graft copolymerization of acrylonitrile onto polystyrene

It is possible to graft vinyl monomers, such as acrylonitrile, onto polystyrene via anionic processes but not by a radical process. Both homopolymerization of the added acrylonitrile and graft copolymerization in which acrylonitrile units are added to the para position on the benzene ring in styrene occur; the conversion of acrylonitrile into polymer depends upon the time and temperature of the reaction and on the concentration of the anionic initiator, butyllithium. A constant 15–20% of the acrylonitrile is converted to graft copolymer while the remainder is homopolymerized; graft copolymer may be separated from homopolymer by selective precipitation from either N,N′-dimethylformamide or aqueous potassium thiocyanate. Treatment of the mixed graft and homopolymer with aqueous sodium hydroxide converts the nitrile into an acid salt and one may conveniently separate homopolymer from graft copolymer in this way. Each polystyrene chain is grafted with acrylonitrile units. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1275–1282, 1997     

Effect of dimethylaminoethyl methacrylate on the graft copolymerization of ethyl acrylate onto hydroxypropyl methylcellulose in aqueous medium

Graft copolymerization of an ethyl acrylate (EA) and dimethylaminoethyl methacrylate (DMAEMA) monomer mixture onto water-soluble hydroxypropyl methylcellulose was investigated with potassium persulfate (KPS) as the initiator in an aqueous medium. The effects of introducing DMAEMA onto the graft copolymerization and the properties of the resulting latex that was produced were studied systematically. The optimum conditions for the graft copolymerization in terms of percentage of grafting and grafting efficiency were determined. The graft copolymer was characterized by Fourier transform infrared spectra, elemental analyses, nuclear magnetic resonance, transmission electron microscopy, and dynamic light scattering methods. The results suggest that the introduction of the DMAEMA monomer clearly accelerates the initial rate of the graft copolymerization, whereas the grafting parameters decrease significantly with increasing amounts of DMAEMA. These results can be attributed to the relatively large size of the DMAEMA molecule, its redox reaction with KPS, its hydrophilicity in water, and its chain transfer effect. The equilibrium humidity adsorption behavior and acid solubility of graft the copolymer films were also studied.     

Fabrication of Poly（4-vinylpyridine） Nanofiber and Fluorescent Poly（4-vinylpyridine）/Porphyrin Nanofiber by Electrospinning

Poly（4-vinylpyridine）（P4-VP） nanofiber and fluoresent poly（4-vinylpyridine）/porphyrin（P4-VP/TPPA） nanofiber were respectively prepared by electrospinning. The effect of the concentration of P4-VP/dimethylformamide （DMF） electrospinning solutions on the morphology of P4-VP nanofiber was investigated and it was found that the average diameter of the nanofiber of P4-VP/DMF increased with the increase of the concentration of the spinning solution. After the addition of TPPA to the P4-VP/DMF spinning solution, the diameter of P4-VP/TPPA nanofiber became even due to the increase of the conductivity of the P4-VP/DMF-TPPA solution. The photoluminescent（PL） spectral analysis indicates that the emission peak position of P4-VP/TPPA nanofiber is almost the same as that of pure TPPA at about 650 nm without peak shift, and when it was stored for 20 days, the emission peak of P4-VP/TPPA nanofiber is also at 650 nm, indicating that the fluorescent property of P4-VP/TPPA nanofiber is stable. Fourier-transform iufrared（FTIR） spectrum confirms the chemical composition of the resulting P4-VP/TPPA composite nanofiber.     

Graft copolymerization of butyl acrylate onto casein initiated by potassium diperiodatonickelate(IV) in alkaline medium

The novel redox system, potassium diperiodatonickelate (Ni(IV))-casein, was used to initiate graft copolymerization of butyl acrylate onto casein under heterogeneous conditions in aqueous 5% potassium hydroxide solution, which showed high grafting efficiency and percent grafting. FT i.r. spectroscopy, thermal analysis and scanning electron microscopy characterized the structures and properties of the grafted copolymer. The effects of synthesis variables in the graft copolymerization have been discussed in the light of grafting efficiency, percent grafting and the rate of polymerization. A possible initiation mechanism is proposed.     

Graft copolymerization of ethyl acrylate onto gelatin using hydrogen peroxide and ascorbic acid in aqueous medium

Gelatin a derived protein from collagen can be modified at 60°C by allowing it to react with ethyl acrylate by use of a novel initiator technique. The polymeric ethyl acrylate side chain is chemically bonded to gelatin. The effects of synthetic variable in the graft copolymerization reactions have been discussed in the light of percent grafting, grafting efficiency, and the rate of polymerization.     

Molecular weight influence on viscosimetric parameters of poly(4-vinylpyridine) polymers

This work describes the effect of the molecular weight on the viscosimetric parameters of poly(4-vinylpyridine) (P4VP) polymers in ethanolic solution. Numerous studies concerning this question have been reported in very separate intervals of molecular weight. We have observed a discordance (discontinuity) in the variation of the intrinsic viscosity as a function of the molecular weight of these polymers ([η]=f(M_w)). In order to establish a general relationship between viscosimetric parameters and M_w, we have considered 10 P4VP samples in a wide interval of molecular weights: 0.75×10⁴ to 153×10⁴. These results have been compared and completed with that of the literature. We have observed that:

(i)

All viscosimetric parameters (intrinsic viscosity [η], Huggins constant k_H, second virial coefficient, viscosimetric expansion coefficient α_η, and critical concentration) change according to a continuous function without a break.

(ii)

The lower is the molecular weight of P4VP; the higher are the variations of the expansion coefficient and the interaction effects.

(iii)

The variation of the intrinsic viscosity versus the molecular weight follows a unique relation in the whole M_w range. In fact, the Berkowitz equation (1), described for a limited range of relatively high M_w (10⁵ to 18.5×10⁵) is extended for all M_w interval values.

(iv)

Empiric laws for [η], k_H, A₂ and C^* and variations as a function of molecular weight were proposed for the P4VP in ethanol.

     

Complexation of sequence-ordered methacrylic acid copolymers with poly(4-vinylpyridine)

The complexation of three kinds of sequence-ordered acid (co)polymers with a base homopolymer was studied. The acid polymers used are poly(methacrylic acid) 1 , alternating (1:1) ethylene-methacrylic acid copolymer 2 , and periodic (2:1) ethylene-methacrylic acid copolymer 3 , and the base polymer is poly(4-vinylpyridine) 4. When mixing a methanol solution of 1, 2 , or 3 with that of 4 (0.1 M of each functional group), precipitate was formed immediately for all polymer pairs. All the precipitates contained carboxyl and pyridyl groups in ca. 1:1 molar ratio and showed IR spectra indicating the hydrogen bonding between carboxyl and pyridyl groups. When mixing dilute methanol solutions (10⁻⁴M) of the above polymer pairs, no precipitation was observed, but the extinction coefficient (ϵ_B) at 255 nm of pyridyl groups in 4 was found to increase with an increasing acid polymer concentration. This is ascribed to hydrogen bonding between carboxyl and pyridyl groups in methanol. Based on the ϵ_B variation, the order of complexation constants for acid/base polymer pairs was estimated as follows: 1/4 pair ∼ 2/4 pair ≫ 3/4 pair. © 1996 John Wiley & Sons, Inc.     

Graft copolymerization of methacrylic acid onto carboxymethyl chitosan

Carboxymethyl chitosan (CMCTS) was prepared and characterized by FTIR, ¹H NMR, and elemental analysis. The graft copolymerization of methacrylic acid (MAA) onto CMCTS using ammonium persulfate (APS) as an initiator was carried out in an aqueous solution. Evidence of grafting was obtained by comparison of FTIR spectra of CMCTS and the grafted copolymer as well as solubility characteristics of the products. The effects of APS, MAA, reaction temperature and time on graft copolymerization were studied by determining the grafting parameters such as grafting percentage and grafting efficiency. With keeping other conditions constant, the optimum conditions were shown as following: [APS]=8 mmol/l, [MAA]=2.4 mol/l, reaction temperature=60-70 °C, reaction time=120 min.     

Graft copolymerization of itaconic acid-methacrylamide comonomers onto poly(ethylene terephthalate) fibers

The graft copolymerization of itaconic acid-methacrylamide (IA-MAAm) comonomers was carried out using benzoyl peroxide as initiator onto poly(ethylene terephthalate) (PET) fibers in an aqueous medium. The grafted fibers were characterized by FTIR, TGA, DSC and SEM analysis. Effect of various parameters on graft yield such as feed composition, feed and initiator concentration, reaction time and temperature were investigated. The graft yield in the presence of MAAm increased because of the synergistic effect of MAAm comonomer. While, the graft yield alone with the IA onto PET fiber was 2.2%, the use of MAAm as a comonomer increased the amount of IA introduced to the PET fiber up to 13.7%. The reactivity ratios for both monomers were determined by using a Fineman-Ross plot. The grafting rate and saturation graft yield was increased upon increasing the temperature between 65 °C and 85 °C. When the temperature increased further than 85 °C, the saturation graft yield decreased. The graft yield has shown an increase up to an initiator concentration of 1.0 × 10⁻² M and slightly decreased. The grafting increased the dyeability with acidic and basic dyes, and moisture absorption capacity but decreased the thermal stability of the fibers.     

Square-wave voltammetric stripping analysis of thallium(III) at a poly(4-vinylpyridine)/mercury film electrode

A poly(4-vinylpyridine)/mercury film electrode (PVP/MFE) was used for the determination of trace thallium(III) by square-wave anodic stripping voltammetry (SWASV). Thallium(III) is preconcentrated onto the PVP/MFE as the anionic forms in chloride medium by the ion-exchange effect of the PVP. The high solubility of thallium in mercury further facilitates the accumulation effect. Various factors influencing the determination of thallium(III) were thoroughly investigated. This modified electrode displayed good resistance to interferences from surface-active compounds and common ions and increased sensitivity when used in conjunction with SWASV. In addition, detection can be achieved without deoxygenation and the electrode can be easily renewed. Applicability to various water samples is illustrated.     

Poly(4-vinylpyridine) catalyzed selective methanolysis of methyl and methylene bromides

The effect of poly(4-vinylpyridine) (PVP) on the methanolysis of methyl bromide and methylene bromide was studied at temperatures between 75 °C and 125 °C. PVP acts as an efficient HBr scavenger promoting the formation of dimethyl ether (DME) and dimethoxymethane (DMM) from the corresponding bromomethanes and methanol in moderate yields with high selectivity. No reaction was observed in the absence of PVP under the conditions adopted. The activity of the catalyst remained unchanged even after five cycles showing the efficacy and application of the polymer as an environmentally green reagent as well as catalyst in this methanolysis reaction.     

Preparation and characterization of graft copolymerization of ethyl acrylate onto hydroxypropyl methylcellulose in aqueous medium

Graft copolymerization of ethyl acrylate (EA) onto water-soluble hydroxypropyl methylcellulose (HPMC) was investigated with potassium persulfate (KPS) as initiator in an aqueous medium. The effects of monomer concentration, initiator concentration, matrix concentration, reaction temperature, reaction time and pre-interacting time in terms of percentage of grafting (G) and grafting efficiency (G _E) are discussed. The graft copolymers were characterized by Fourier transform infrared spectra (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction analysis (XRD) and differential scanning calorimetry (DSC). In addition, equilibrium humidity adsorption behavior of the pure grafted copolymers was also studied.     

Graft copolymerization of N-vinyl-2-pyrrolidone onto pre-irradiated poly(vinylidene fluoride) powder

Graft copolymerization of N-vinyl-2-pyrrolidone (NVP) onto ⁶⁰Co γ-ray pre-irradiated poly (vinylidene fluoride) (PVDF) powder was investigated to find out the relationship between the degree of grafting (DG) and various factors, including monomer concentration, irradiation dose, reaction time, catalyst and so on. The DG can be calculated by comparing the amount of nitrogen element in the resulting copolymer (PVDF-g-PVP) powder with that in PVP on the basis of element analysis. The presence of PVP in the resulting PVDF powder was confirmed by the comparative studies of pristine PVDF and grafted PVDF powder through Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), thermo gravimetric analyzer (TGA) and differential scanning calorimetry (DSC), respectively. When the reaction was performed at the monomer concentration of 20% (vol.) and the absorbed dose of 40 kGy for 3 h in water, the max. DG of 17.7% was obtained.     

聚(4-偶氮磺酸苯乙烯-co-4-乙烯基吡啶)与本征态聚苯胺的氢键自组装及其光电转换性能

合成了一种新的共聚体——聚(4-偶氮磺酸苯乙烯-co-4-乙烯基吡啶), 它含有吡啶环, 能作为氢受体与本征态聚苯胺进行氢键自组装. 在紫外光照下, 组装膜通过偶氮磺酸基的光解, 形成稳定的共价交联结构, 在电解质水溶液中也不被破坏, 可用作光电转换膜, 并能在盐水溶液中直接测定它的光电流. 结果表明含有本征态聚苯胺的自组装膜是一种良好的光电转换材料.     

Charge-mosaic membrane from gamma-irradiated poly(styrene-butadiene-4-vinylpyridine) triblock copolymer

Poly(styrene-butadiene-4-vinylpyridine) triblock copolymers were prepared from styrene (S), butadiene (B), and 4-vinylpyridine (P) by sequential anionic polymerization with n-butyllithium as initiator and benzene as solvent. The triblock copolymer was characterizated by gel-permeation chromatography (GPC), transmission electron microscopy (TEM), and viscoelastic spectrometry. Films of the triblock copolymer cast from solution in mixtures of chloroform and n-butyraldehyde were subjected to gamma-ray irradiation to form cross-linked networks, Cationic and anionic groups were introduced by sulfonation and quater-nization to obtain charge-mosaic membranes. The resulting membrane had substantial cation-exchange and anion-exchange capacities. The membranes were very permeable to electrolyte (J_KCI = 2.10×10^?8 mol/cm² s). © 1993 John Wiley & Sons, Inc.     

Graft copolymerization of epichlorohydrin and ethylenediamine onto cellulose derived from agricultural by-products for adsorption of Pb(II) in aqueous solution

In order to develop a low-cost and high efficient absorbent, cellulose was extracted from peanut hulls, soybean shells and grapefruit peels using 17.5 % NaOH and then copolymerized with epichlorohydrin and ethylenediamine. Infrared spectra and N contents show that the cellulose was copolymerized successfully with the ethylenediamine. Factors affecting the adsorption behavior of Pb(II), such as pH, temperature, ratio of solid to liquid, competitive sorption of various metal ions, initial metal concentration and adsorption time, were then investigated. The adsorption equilibrium could be obtained within 120 min and the kinetic adsorption processes fitted well with the pseudo-second order kinetic model. The isotherm adsorption data fitted well with Langmuir adsorption model and the maximum absorption capacities of the modified peanut hulls, soybean shells and grapefruit peels were 47.8, 101 and 232 mg g^?1, respectively. The competitive adsorption of mixed metal ions demonstrated that Pb(II) was preferentially removed from solution by the modified peanuts shells, soybean shells and grapefruit peels, then Cu(II) and Cr(III). Desorption of Pb(II) from modified peanut hulls, soybean shells and grapefruit peels was effectively achieved in a 1 mol L^?1 HCl solution. Ethylenediamine-modified grapefruit peels exhibited higher absorption performance than the ethylenediamine-modified soybean shells and peanut hulls and can be used as potential low-cost and high efficient absorbents for the removal of lead ions from wastewater.     

Poly(4-vinylpyridine) catalyzed hydrolysis of methyl bromide to methanol and dimethyl ether

The hydrolysis of methyl bromide with neutral water is performed in the presence and absence of various amines in a batch reactor at different temperatures (50–125 °C). Screening of poly(4-vinylpyridine) as a potential reusable solid amine catalyst showed maximum efficiency. This significant enhancement in efficiency is due to the capture of HBr by solid PVP and remains phase-separated driving the reaction forward. The major advantage of this process is that the polymer can be easily regenerated and reused without loss of activity making it a very effective catalyst for the conversion of methyl halides to methanol and dimethyl ether.