Crosslinking of polyimides via spirodilactone unit in polymer backbone

A new approach for the crosslinking of polyimides via the lactamization of spirodilactone unit in polyimide backbone was studied by two means: model reaction and the comparison of the properties of the polyimide precursors to those of the crosslinking polymers. Polyimides 4 and 5 were soluble in N,N′dimethylacetamide (DMAc), dimethylformamide (DMF), dimethylsulfoxide (DMSO), N′-methylpyrrolidone (NMP), and other common organic solvents, whereas their corresponding crosslinking polymers were insoluble in these solvents. The glass transition temperatures for polyimide 5 and its crosslinking polymer were 262°C and 291°C, whereas those for polyimide 4 and its crosslinking polymer were 265°C and 360°C. The weight-loss rate of the crosslinking polymers was apparently slower than that of the precursors when the temperature was > 400°C. The 10% weight-loss temperature for the polyimides 4 and 5 was < 500°C, whereas that for the crosslinking polymers was close to or above 600°C. The results indicate that this type of crosslinking polymer has good thermal properties. The temperature for the formation of lactam was above 180°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3680–3686, 1999     

Synthesis and Characterization of Fluorinated Polyimide Derived from 3,3′‐Diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane

A novel aromatic diamine monomer, 3,3′‐diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane (PAFM), was successfully synthesized by coupling of 2‐isopropylaniline and 3,4‐difluorobenzaldehyde. The aromatic diamine was adopted to synthesize a series of fluorinated polyimides by polycondensation with various dianhydrides: pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA) and 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) via the conventional one‐step method. These polyimides presented excellent solubility in common organic solvents, such as N,N‐dimethylformamide (DMF), N,N‐dimethyl acetamide (DMAc), dimethyl sulfoxide (DMSO), N‐methyl‐2‐pyrrolidone (NMP), chloroform (CHCl₃), tetrahydrofuran (THF) and so on. The glass transition temperatures (T_g) of fluorinated polyimides were in the range of 260–306°C and the temperature at 10% weight loss in the range of 474–502°C. Their films showed the cut‐off wavelengths of 330–361 nm and higher than 80% transparency in a wavelength range of 385–463 nm. Moreover, polymer films exhibited low dielectric properties in the range of 2.76–2.96 at 1 MHz, as well as prominent mechanical properties with tensile strengths of 66.7–97.4 MPa, a tensile modulus of 1.7–2.1 GPa and elongation at break of 7.2%–12.9%. The polymer films also showed outstanding hydrophobicity with the contact angle in the range of 91.2°–97.9°.     

Synthesis and Characterization of Novel Poly(Arylene Ether)s from 1,3‐bis(4‐Hydroxyphenyl) Benzene

Abstract

Several poly(aryl ether)s have been prepared by the condensation of 1,3‐bis(4‐hydroxy phenyl) benzene with different trifluoromethyl activated bis‐fluoro compounds. IR, ¹H and ¹³C NMR, and elemental analyses have established the resulting polymer structures. The properties of the polymers have been evaluated by DSC, TGA, dynamic mechanical analysis (DMA) and stress–strain analysis. The polymers 1a and 1c showed semi‐crystalline behavior as evident by sharp crystalline melting peaks at 299°C and 330°C along with glass transitions at 202°C and 216°C, respectively. The polymers showed very good thermal stability in air, high modulus, and high tensile strength with low elongation at break.     

Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

Shape‐memory effect in hyperbranched poly(ethyleneimine)‐modified epoxy thermosets

A series of shape‐memory epoxy thermosets were synthesized by crosslinking diglycidyl ether of bisphenol A with mixtures of commercially available hyperbranched poly(ethyleneimine) and polyetheramine. Thermal, mechanical and shape‐memory properties were studied and the effect on them of the content and structure of the hyperbranched polymer was discussed. Measurements showed that the glass transition temperature can be tailored from 60 °C to 117 °C depending on the hyperbranched polymer content, and all formulations showed an appropriate glassy/rubbery storage modulus ratio. Shape‐memory programming was carried out at TgE′ given the excellent mechanical properties of the materials, with maximum stress and failure strain up to 15 MPa and 60%, respectively. The resulting shape‐memory behavior was excellent, with maximum shape recovery and shape fixity of 98% as well as a fast shape‐recovery rate of 22%/min. The results show that hyperbranched poly(ethyleneimine) as a crosslinking agent can be used to enhance mechanical and shape‐memory properties with different effects depending on the crosslinking density. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 924–933     

Internal acetylene unit linked para to the aromatic ring as a crosslink site for polyimide

Crosslinking behavior of internal acetylene units linked para to the aromatic rings was investigated by preparing polyimide from 4,4′-diaminodiphenylacetylene (p-intA) and 2,2′-bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA). Polyimide was also prepared from 1,4-phenylenediamine (PDA) and 6FDA for comparison. The polymers were moderately to highly viscous at the stage of polyamide acid. Thermal imidization gave polyimide having acetylene units that are linked para to the aromatic connecting units. Differential scanning calorimetry (DSC) measurement of the polymer revealed that exotherm due to the crosslinking of the acetylene unit appeared at ca. 330°C. After thermal treatment at high temperature such as 350 and 400°C, onset of the exotherm shifted to higher temperature and the amount of the exotherm became smaller. The dynamic mechanical properties of the uncrosslinked polyimide film treated at 250°C had a glass transition temperature (T_g) at 330°C with a considerable drop in the storage modulus at this temperature. After the film was exposed to a higher temperature to induce crosslinking, the T_g was observed to increase to above 400°C and the storage modulus was maintained to higher temperatures. Tensile properties of the polyimide showed that the films had good mechanical properties. © 1996 John Wiley & Sons, Inc.     

Novel Crosslinked Guest-Host System with Stable Second-Order Nonlinearity

Abstract

An epoxy-based nonlinear optical (NLO) polymeric material incorporating 4-(4′-nitrophenylazo) phenylamine has been synthesized and subsequently functionalized with acryloyl groups. A glass transition temperature (T ₈)of 108°C and a degradation temperature (air) of 251°C were recorded. After crosslinking at 160°C for 2 hours, the T ₈ of the polymer increased to 146°C. In order to increase the nonlinear optical chromophore concentration and the crosslinking density, the crosslink-able NLO dye, 2,4-acryloyloxy (4′-phenylazo nitrobenzene), was processed and poled in this epoxy-based NLO material matrix in a manner similar to a typical guest-host system, and thermally crosslinked under the above condition in the poled phase. The crosslinked guest-host material was found to be amorphous with a T ₈ of approximately 132°C. It also exhibits a second-order nonlinear optical coefficient d ₃₃ of 14.14 pm/V at a maximum doping level of 33% by weight of the NLO dye, and retains 93% of its original d ₃₃ value after being subjected to thermal treatment at 100°C for 168 hours. The behavior of the crosslinked polymer and the crosslinked guest-host polymer is discussed.     

Thermomechanical behavior of a polyphenylquinoxaline

Crosslinking of linear poly[2,2′-(1,4-phenylene)-6,6′-bis(3-phenylquinoxaline)] (PPQ) by isothermal heat exposure in the temperature range between 425 and 490°C was investigated by means of torsional braid analysis. The change in glass transition temperature due to isothermal exposure was used as a kinetic parameter. In order to determine the effect of molecular weight and type of polymer chain ends, three PPQ samples were prepared that differed only in molecular weight and polymer chain endgroups. The apparent activation energy of isothermal crosslinking was independent of molecular weight and chain endings. Its value of 60 kcal/mole is the same as that for the thermal degradation of PPQ (determined by isothermal weight loss measurements). The rates of change of T_g at a particular temperature, however, are a function of both molecular weight (at least for these polymers that do not have a sufficiently high molecular weight) and the type of polymer chain ends. It was observed that isothermally crosslinked PPQ gave a higher break point in the TGA curve and also an increased char yield at 800°C than the linear precursor.     

Modification of poly(vinyl chloride). XIII. Crosslinking of poly(vinyl chloride) with dithiols and properties of the crosslinked products

PVC was crosslinked by immersing PVC–dithiol blends in ethylenediamine at 30°C. Properties of the products depended on the chain length and chemical structure of the crosslinkage and on the molecular weight of the polymer chain between crosslinks M_c. Crosslinking by the agent of soft structure and long molecular chain resulted in high tensile strength at break and impact strength and low brittle temperature. The use of the crosslinking agent of short molecular chain gave high yield strength, Young's modulus, and heat distortion temperature. The relation of M_c and the chemical structure of the crosslinks to the properties of the crosslinked rigid polymer was discussed in regard to the crosslinking effect and plasticizing effect.     

Synthesis and NMR characterization of 6‐Phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose

Cellulose ( 1 ) was converted for the first time to 6‐phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 6 ) in 33% overall yield. Intermediates in the five‐step conversion of 1 to­ 6 were: 6‐O‐tritylcellulose ( 2 ), 6‐O‐trityl‐2,3‐di‐O‐methylcellulose ( 3 ), 2,3‐di‐O‐methylcellulose ( 4 ); and 6‐bromo‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 5 ). Elemental and quantitative carbon‐13 analyses were concurrently used to verify and confirm the degrees of substitution in each new polymer. Gel permeation chromotography (GPC) data were generated to monitor the changes in molecular weight (DP_w) as the synthesis progressed, and the compound average decrease in cellulose DP_w was ～ 27%. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to characterize the decomposition of all polymers. The degradation temperatures ( °C) and percent char at 500 °C of cellulose derivatives 2 to 6 were 308.6 and 6.3%, 227.6 °C and 9.7%, 273.9 °C and 30.2%, 200.4 °C and 25.6%, and 207.2 °C and 27.0%, respectively. The glass transition temperature (T_g) of­6‐O‐tritylcellulose by dynamic mechanical analysis (DMA) occurred at 126.7 °C and the modulus (E′, Pa) dropped 8.9 fold in the transition from ?150 °C to + 180 °C (6.6 × 10⁹ to 7.4 × 10⁸ Pa). Modulus at 20 °C was 3.26 × 10⁹ Pa. Complete proton and carbon‐13 chemical shift assignments of the repeating unit of the title polymer were made by a combination of the HMQC and COSY NMR methods. Ultimate non‐destructive proof of carbon–carbon bond formation at C6 of the anhydroglucose moiety was established by generating correlations between resonances of CH₂6 (anhydroglucose) and C1′, H2′, and H6′ of the attached aryl ring using the heteronuclear multiple‐bond correlation (HMBC) method. In this study, we achieved three major objectives: (a) new methodologies for the chemical modification of cellulose were developed; (b) new cellulose derivatives were designed, prepared and characterized; (c) unequivocal structural proof for carbon–carbon bond formation with cellulose was derived non‐destructively by use of one‐ and two‐dimensional NMR methods. Copyright © 2002 John Wiley & Sons, Ltd.     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Preparation,characterization, and properties of poly(thioether ether imide)s from isomeric bis(chlorophthalimide)s and 4,4′‐thiobisbenzenethiol

A series of isomeric poly(thioether ether imide)s (PTEIs) containing both thioether and ether linkages were prepared by nucleophilic substitution reaction of isomeric bis(chlorophthalimide)s with 4,4′‐thiobisbenzenethiol. The inherent viscosities of these polymers were in the range of 0.40–0.56 dL/g in m‐cresol at 30°C. The T_g values of PTEIs were 196–236°C; T_5% values reached up to 509–529°C in nitrogen and 508–534°C in air, which indicated this kind of polyimide possessed excellent thermal stability. The hydrolytic stability was arranged in the order: a > b > c > d > e, and improved with increasing the content of 3‐substituted phthalimide unit in the polymer backbone. Flexible films could be cast from the polymer solution with a solid content of 10%. The PTEI films exhibited good mechanical properties with tensile strengths of 90–104 MPa, elongations at break of 6.6–7.9%, and tensile moduli of 2.3–2.6 GPa. The minimum complex viscosity of PTEIs c was about 100 Pa·s at 310°C and the minimum melt viscosity of PTEIs (a–e) decreased with increasing the content of unsymmetrical 3,4′‐substituted phthalimide units. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis of phosphate‐pendant polymers and their application to thermally latent polymeric initiators

A novel phosphate monomer, O‐p‐(methacryloyloxymethyl)benzyl O,O‐diethyl phosphate (MDP) was synthesized by the reaction of diethyl phosphorochloridate with 1,4‐benzenedimethanol, followed by the reaction with methacryloyl chloride in the presence of triethylamine. The radical polymerization of MDP and copolymerization with methyl methacrylate were carried out in the presence of 2,2′‐azobisisobutyronitrile (3 mol %) in dimethylacetamide at 60 °C for 20 h to afford phosphate‐pendant polymers. The polymerization of glycidyl phenyl ether (GPE) was carried out with the phosphate‐pendant polymer as an initiator in the presence of ZnCl₂. The polymerization did not proceed below 90 °C but rapidly proceeded above 90 °C to afford polyGPE. The phosphate‐pendant polymer served as a good thermally latent polymeric initiator. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3365–3370, 2001     

Highly phenylated poly(aryl ether phthalazine)s

Two series of novel amorphous poly(aryl ether phthalazine)s have been prepared via an intramolecular ring closure reaction of poly(aryl ether ketone)s (PAEKs) with hydrazine monohydrate. Fluorinated PAEKs, which display solubility in solvents incorporating a ketone functionality such as acetone or ethyl acetate, were converted to poly(aryl ether phthalazine)s to observe if these polymers would display similar solubility characteristics. The poly(aryl ether phthalazine)s have glass transition temperatures in the range of 278–320°C and show 5% weight loss points greater than 500°C in air and nitrogen atmospheres. The fluorinated poly(aryl ether phthalazine)s were not soluble in ketonic solvents. A series of poly(aryl ether phthalazine)s incorporating pendant 2-naphthalenyl moieties has been prepared in an attempt to produce amorphous, thermally stable polymers with high glass transition temperatures. The polymers have glass transition temperatures in the range of 287–334°C and show 5% weight loss points greater than 500°C in air and nitrogen atmospheres. Poly(aryl ether phthalazine)s undergo an exothermic reaction above the glass transition temperature. The major product of this reaction is a rearrangement of the phthalazine moieties to quiazoline moieties, however some crosslinking of the polymers occurs. Cured samples of the poly(aryl ether phthalazine)s show a small increase in the polymer T_g and are insoluble in all solvents tested. © 1996 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 34:1897–1905, 1996     

Synthesis and characterization of phthalazinone‐based poly(aryl ether ketone) derived from 4,4′‐dichlorobenzophenone

As distinguished from the conventional preparation of poly(aryl ether ketone)s utilizing 4,4′‐difluorobenzophenone, a novel synthetic method of high molecular weight poly(phthalazinone ether ketone) derived from 4,4′‐dichlorobenzophenone was studied. Reaction conditions to get high molecular weight polymer were investigated in details. Experimentally, sulfolane was chosen as the reaction media and high molecular weight polymer could be obtained in 7–8 hr at 210°C. The cyclic oligomers in the polymer product reduced to below 3.0% when the concentration of the reactant is 1.6–1.7 g/ml. Fourier transform infrared (FT‐IR), ¹H NMR, and elemental analysis were used to confirm the structure of the obtained polymer. The amorphous polymer showed reasonable solubility in selective solvent, such as chloroform and N‐methyl‐2‐pyrrolidone, and tough, flexible, and transparent thin film can be readily prepared from their N‐methyl‐2‐pyrrolidone solution. The obtained polymer showed high glass transition temperature (T_g) up to 261°C detected by differential scanning calorimetry (DSC), and the temperature of 5% weight loss under nitrogen higher than 500°C detected by thermal gravimetric analysis (TGA), indicating its excellent thermal stability. Copyright © 2011 John Wiley & Sons, Ltd.     

Mechanical properties of gradient copolymers of styrene and n‐butyl acrylate

The mechanical properties of linear and V‐shaped compositional gradient copolymer of styrene and n‐butyl acrylate with composition of around 55 wt % styrene were investigated by comparing with their block copolymer counterparts. Compared with their block copolymer counterparts, the gradient copolymers showed lower elastic modulus, much larger elongation at break, and similar ultimate tensile strength at room temperature. This performance could be ascribed to that the local moduli continuously change from the hardest nanodomains to the softest nanodomains in the gradient copolymer, which alleviates the stress concentration during tensile test. Compared with the V‐shaped gradient (VG) copolymer, the linear gradient copolymer showed much higher elastic modulus but lower elongation at break. The mechanical properties of the gradient copolymers were more sensitive to the change in temperature from 9 °C to 75 °C. With recovery temperature increased from 10 °C to 60 °C, the strain recovery of VG copolymer would change steadily from 40% to 99%. However, the elastic recovery of linear and triblock copolymer was poor even at 60 °C. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 860–868     

含硫醚可溶性聚芳醚酮的合成及电子束辐照的研究

聚醚醚酮(PEEK)因具有优异的机械性能、耐热性、耐化学腐蚀性等优点而广泛应用于航空航天、电子器件、机械仪表等领域．具有刚性结构的聚醚醚酮有极好的耐溶剂性,不溶于一般的有机溶剂,并且需在较高的温度下进行加工．近20年来,人们不断开发性能优异的聚醚醚酮新材料,在聚合物主链上引入不同的功能基团(如萘环、氮杂萘环等)及侧基功能基团(如苯、三氟甲基等),以提高聚芳醚酮的溶解性,或者通过共聚和共混等方式进一步改善材料的使用性能和加工性能,     

Novel Non‐Coplanar and Tertbutyl‐Substituted Polyimides: Solubility,Optical, Thermal and Dielectric Properties

A novel aromatic diamine monomer bearing tertbutyl and 4‐tertbutylphenyl groups, 3,3′‐ditertbutyl‐4,4′‐diaminodiphenyl‐4′′‐tertbutylphenylmethane (TADBP), was prepared and characterized. A series of non‐coplanar polyimides (PIs) were synthesized via a conventional one‐step polycondensation from TADBP and various aromatic dianhydrides including pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (OPDA), 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) and 4,4′‐(hexafluoroisopropylidene)dipthalic anhydride (6FDA). All PIs exhibit excellent solubility in common organic solvents such as N,N‐dimethylformamide (DMF), N,N‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), dimethyl sulfoxide (DMSO), chloroform (CHCl₃), tetrahydrofuran (THF), and so on. Furthermore, the obtained transparent, strong and flexible polyimide films present good thermal stability and outstanding optical properties. Their glass transition temperatures (T_gs) are in the range of 298 to 347°C, and 10% weight loss temperatures are in excess of 490°C with more than 53% char yield at 800°C in nitrogen. All the polyimides can be cast into transparent and flexible films with tensile strength of 80.5–101 MPa, elongation at break of 8.4%–10.5%, and Young's modulus of 2.3–2.8 GPa. Meanwhile, the PIs show the cutoff wavelengths of 302–356 nm, as well as low moisture absorption (0.30% –0.55%) and low dielectric constant (2.78–3.12 at 1 MHz).     

Synthesis and proton conductivity of sulfonated,multi‐phenylated poly(arylene ether)s

A series of sterically‐encumbered, sulfonated, poly(arylene ether) copolymers were synthesized and their proton conductivity examined. The series was prepared by copolymerizing a novel monomer, 2″,3″,5″,6″‐tetraphenyl‐[1,1′:4',1″:4″,1″':4″',1″″‐quinquephenyl]‐4,4″″‐diol, with 4,4'‐difluorobenzophenone and bisphenol A. Subsequent sulfonation and solution casting provided membranes possessing ion exchange capacities of 1.9 to 2.7 mmol/g and excellent mechanical properties (Young's modulus, 0.2–1.2 GPa; tensile strength, 35–70 MPa; elongation at break, 62–231%). Water uptake ranged from 34 to 98 wt% at 80 °C/100% RH. Proton conductivities ranged between 0.24 to 16 mS/cm at 80 °C/60% RH, and 3 to 167 mS/cm at 80 °C/95% RH. TEM analysis of the polymers, in the dehydrated state, revealed isolated spherical aggregates of ions, which presumably coalesce when hydrated to provide highly conductive pathways. The strategy of using highly‐encumbered polymer frameworks for the design of mechanically‐robust and dimensionally‐stable proton conducting membranes is demonstrated. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2579‐2587     

Polyimide containing internal acetylene units linked para to the aromatic ring

4,4′-Diaminodiphenylacetylene (p-intA) was reacted with 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA), 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) and pyromellitic dianhydride (PMDA) in N-methyl-2-pyrrolidone (NMP) to give poly(amic acid) solution of moderate to high viscosity. Thermal imidization gave polyimide having acetylene units that are linked para to the aromatic connecting unit. Polyimide having acetylene units that are linked meta to the aromatic connecting unit also was prepared utilizing 3,3′-diaminodiphenylacetylene (m-intA) for comparison. The crosslinking behavior of the acetylene units was observed with DSC. Exotherm due to the crosslinking of the para-linked acetylene units appeared at ca. 340 to 380°C depending on the structure of polyimide, whereas meta-linked acetylene units appeared at lower temperature as 340–350°C. After thermal treatment at high temperature such as 350 or 400°C, the amount of the exotherm became smaller and finally disappeared on DSC, confirming the progress of crosslinking. Dynamic mechanical properties of the polyimide films show that glass transition temperature increased with higher heat treatment, also confirming the progress of crosslinking. Tensile properties of the polyimide films showed that rigid polyimide films consisting of p-intA with BPDA or PMDA have considerably higher modulus than those consisting of m-intA. Cold-drawing of the poly(amic acid) followed by imidization gave much higher modulus in the case of rigid polyimide. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2395–2402, 1997