Polyisobutylene‐based segmented polyureas. I. Synthesis of hydrolytically and oxidatively stable polyureas

Novel segmented polyurea elastomers containing soft polyisobutylene (PIB) segments were synthesized and characterized. The key ingredient, primary amine‐telechelic PIB oligomers (NH₂‐PIB‐NH₂) with number average molecular weights of 2500 and 6200 g/mol were synthesized. PIB‐based polyureas were prepared by using various aliphatic diisocyanates and diamine chain extenders with hard segment contents between 9.5 and 46.5% by weight. All copolymers displayed microphase morphologies as determined by dynamic mechanical analysis. Tensile strengths of nonchain‐extended and chain‐extended polyureas showed a linear dependence on the urea hard segment content. PIB‐based polyureas prepared with NH₂‐PIB‐NH₂ of M_n = 2500 g/mol, 4,4′‐methylendbis(cyclohexylisocyantate), and 1,6‐diaminohexane containing 45% hard segment exhibited 19.5 MPa tensile strength which rose to 23 MPa upon annealing at 150 °C for 12 h. With increasing hard segment content, elongation at break decreased from ～ 450% to a plateau of 110%. The hydrolytic and oxidative stability of PIB‐based polyureas were unprecedented. Although commercial “oxidatively resistant” thermoplastic polyurethanes degraded severely upon exposure to boiling water or concentrated nitric acid, the experimental polyureas survived without much degradation in properties. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 38–48, 2009     

Rubbery wound closure adhesives. I. design,synthesis, characterization,and testing of polyisobutylene‐based cyanoacrylate homo‐ and co‐networks

Novel rubbery wound closures containing various proportions and molecular weights of polyisobutylene (PIB) and poly(2‐octyl cyanoacrylate) [P(OctCA)] for potential clinical use were designed, synthesized, characterized, and tested. Homo‐networks were prepared by crosslinking 3‐arm star‐shaped PIBs fitted with terminal cyanoacrylate groups, [Ø(PIB‐CA)₃], and co‐networks by copolymerizing Ø(PIB‐CA)₃ with OctCA using N‐dimethyl‐p‐toluidine (DMT). Neat Ø(PIB‐CA)₃, and Ø(PIB‐CA)₃/OctCA blends, upon contact with initiator, polymerize within seconds to optically transparent strong rubbery co‐networks, Ø(PIB‐CA)₃‐co‐P(OctCA). Homo‐ and co‐network formation was demonstrated by sol/gel studies, and structures and properties were characterized by a battery of techniques. The T_g of P(OctCA) is 58 °C by DSC, and 75 °C by DMTA. Co‐networks comprising 25% Ø(PIB‐CA)₃ (M_n = 2400 g/mol) and 75% P(OctCA) are stronger and more extensible than skin. Short and long term creep studies show co‐networks exhibit high dimensional stability and <6% creep strain at high loading. When deposited on porcine skin co‐networks yield hermetically‐adhering clear rubbery coatings. Strips of porcine skin coated with co‐networks could be stretched and twisted without compromising membrane integrity. The co‐network is nontoxic to L‐929 mouse fibroblasts. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1640–1651     

Synthesis and Characterization of Thermoplastic Polyurethaneureas based on Polyisobutylene and Poly(tetramethylene oxide) Segments

New thermoplastic polyurethaneureas (TPUU) based on polyisobutylene (PIB) and poly(tetramethylene oxide) (PTMO) segments have been synthesized possessing tensile properties comparable to conventional PTMO based TPUs. PIB based TPUU containing 35 weight (wt)% hard segment was synthesized by chain extension of H₂N-Allyl-PIB-Allyl-NH₂ with 4,4′ -methylene bis(phenylisocyanate) (MDI) and 1,4-butanediol (BDO) in toluene. The ultimate tensile strength (UTS) = 12 MPa and ultimate elongation = 70% were inferior to PTMO based polyurethane (UTS = 35 MPa, elongation at break = 600%). H₂N-Allyl-PIB-Allyl-NH₂ and HO-PTMO-OH in different proportions were chain extended in presence of MDI and BDO to obtain TPUUs containing 35 wt% hard segment. The polymers exhibited M _ns = 84000–138000 with polydispersity indices (PDIs) = 1.7–3.7. The UTS = 23–32 MPa and elongation at break = 250–675% was comparable to that of PTMO based polyurethane and significantly higher than the PIB based TPUU with the same Shore hardness. The Young's modulus of the polymers was strongly dependent and directly proportional to the PIB wt% in the SS of the TPUUs.     

Synthesis and characterization of novel dendritic (arborescent,hyperbranched) polyisobutylene–polystyrene block copolymers

The synthesis of novel arborescent (arb; randomly branched, “tree‐like,” and often called “hyperbranched”) block copolymers comprised of rubbery polyisobutylene (PIB) and glassy polystyrene (PSt) blocks (arb‐PIB‐b‐PSt) is described. The syntheses were accomplished by the use of arb‐PIB macroinitiators (prepared by the use of 4‐(2‐methoxyisopropyl) styrene inimer) in conjunction with titanium tetrachloride (TiCl₄). The effect of reaction conditions on blocking of St from arb‐PIB was investigated. Purified block copolymers were characterized by ¹H NMR spectroscopy and Size Exclusion Chromatography (SEC). arb‐PIB‐b‐PSt with 11.7–33.8 wt % PSt and M_n = 468,800–652,900 g/mol displayed thermoplastic elastomeric properties with 3.6–8.7 MPa tensile strength and 950–1830% elongation. Samples with 26.8–33.8 wt % PSt were further characterized by Atomic Force Microscopy (AFM), which showed phase‐separated mixed spherical/cylindrical/lamellar PSt phases irregularly distributed within the continuous PIB phase. Dynamic Mechanical Thermal Analysis (DMTA) and solvent swelling of arb‐PIB‐b‐PSt revealed unique characteristics, in comparison with a semicommercial PSt‐b‐PIB‐b‐PSt block copolymer. The number of aromatic branching points of the arb‐PIB macroinitiator, determined by selective destruction of the linking sites, agreed well with that calculated from equilibrium swelling data of arb‐PIB‐b‐PSt. This method for the quantitative determination of branching sites might be generally applicable for arborescent polymers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1811–1826, 2005     

Polyisobutylene-containing block polymers by sequential monomer addition. IV. New triblock thermoplastic elastomers comprising high Tg styrenic glassy segments: Synthesis,characterization and physical properties

New linear triblock thermoplastic elastomers (TPEs) comprising a rubbery polyisobutylene (PIB) midblock flanked by two glassy endblocks of various styrenic polymers have been synthesized by living carbocationic polymerization by sequential monomer addition. First isobutylene (IB) was polymerized by a bifunctional tert-ether (dicumyl methyl ether) initiator in conjunction with TiCl₄ coinitiator in CH₃Cl/methylcyclohexane (MeCHx) (40/60 v/v) solvent mixtures at ?80°C. After the living narrow molecular weight distribution PIB midblock ( = 1.1–1.2) has reached the desired molecular weight, the styrenic monomers together with an electron pair donor (ED) and a proton trap (di-tert-butylpyridine, DtBP) were added to start the blocking of the glassy segments from the living ⊕PIB⊕ chain ends. While p-methylstyrene (pMeSt), p-t-butylstyrene (ptBuSt) and indene (In) gave essentially 100% blocking to the corresponding glassy endblocks, the blocking of 2,4,6-trimethylstyrene (TMeSt) and α-methylstyrene (αMeSt) were ineffective. Uncontrolled initiation by protic impurities was prevented by the use of DtBP. In the simultaneous presence of DtBP and the strong ED N,N-dimethylacetamide (DMA), TPEs with good mechanical properties (10–20 MPa tensile strength, 300–600% elongation) were prepared. The products exhibit a low and a high temperature T_g characteristic of phase separated rubbery and glassy domains. The service temperature of these new TPEs exceeds that of PSt–PIB–PSt triblock copolymers due to the higher T_gs (PpMeSt = 108, PptBuSt = 142 and PIn = 220–240°C) of the outer blocks. The T_g of the glassy blocks can be regulated by copolymerizing two styrene derivatives; a triblock copolymer with outer blocks of poly(pt-butylstyrene-co-indene) showed a single glassy transition T_g = +165°C, i.e., in between that of PptBuSt and PIn. Virgin TPEs have been repeatedly compression molded without deterioration of physical properties. The high melt flow index obtained with a TPE containing PptBuSt endblocks suggests superior processability relative to those with PSt end-blocks. The tensile strength retention at 60°C of the former TPE is far superior to that of a PSt–PIB–PSt triblock of similar composition.     

High‐molecular‐weight polyisobutylenes (PIBs) and PIB networks from liquid PIBs by thiol‐ene clicking

We report the synthesis of high‐molecular‐weight linear polyisobutylenes (PIBs) and PIB networks from low‐molecular‐weight PIB by thiol‐ene click chemistry. Thus, liquid allyl‐telechelic PIB was reacted with small di‐ and tri‐thiols, and the thiolated intermediates chain‐extended by UV‐ or thermally induced free radical initiation to linear and crosslinked products. PIB networks were also prepared by crosslinking SH‐telechelic PIB with a small triallyl compound. Linear products were characterized by ¹H NMR spectroscopy and GPC, and networks by FTIR spectroscopy, extractables, swelling, and permanent set. The effect of reaction conditions (nature of thiol chain extender, concentration of photo‐ and thermal initiators, UV radiation time, and reagent concentrations) on chain extension and crosslinking was investigated. Under well‐defined conditions high‐molecular‐weight PIBs and tight PIB networks were prepared. Thiol‐ene click chemistry provides novel thiolated PIB derivatives and is a useful strategy for the convenient preparation of high‐molecular‐weight rubbery PIBs and tight PIB networks from low‐molecular‐weight PIB precursors. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019     

Novel polyisobutylene/poly(dimethylsiloxane) bicomponent networks. I. Synthesis and characterization

The synthesis of novel polyisobutylene (PIB)/poly(dimethylsiloxane) (PDMS) bicomponent networks is described. The synthesis strategy (see Figure 1) was to prepare well-defined and -characterized allyl-tritelechelic polyisobutylenes [ϕ(PIB—C—C=C)₃] and SiH-ditelechelic poly(dimethylsiloxanes) (HSi–PDMS–SiH) and then crosslink these moieties by hydrosilation. The ϕ(PIB—C—C=C)₃ was prepared by living isobutylene polymerization followed by end-quenching with allyltrimethylsilane, whereas the HSi–PDMS–SiH was obtained by equilibrium polymerization of octamethylcyclotetrasiloxane and tetramethyldisiloxane. The detailed structures of the starting polymers were characterized by GPC and ¹H-NMR spectroscopy. A series of PIB/PDMS bicomponent networks of varying compositions and average molecular weights between crosslinks (M _c) of ∼ 20,000 g/mol were assembled. Optimum crosslinking conditions were defined in terms of H₂PtCl₆ catalyst concentration, nature of solvent, time, temperature, and stoichiometry of ∼ CH₂CH=CH₂/∼SiH groups, allowing for the convenient synthesis of well-defined model bicomponent networks. Swelling studies and elemental analysis confirm the correctness of the synthetic strategy. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1891–1899, 1998     

Precision synthesis and characterization of thymine‐functionalized polyisobutylene

A new two‐step synthesis of polyisobutylene (PIB) with precisely one thymine functionality per chain (PIB‐T) is reported. The primary hydroxyl‐functionalized PIB (PIB‐OH) precursor was prepared by direct functionalization via living carbocationic polymerization of isobutylene initiated by the α‐methylstyrene epoxide/TiCl₄ system. Matrix assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI‐ToF MS) of a low molecular weight PIB‐OH precursor demonstrated the effectiveness of direct functionalization by this method. A PIB‐acrylate precursor (PIB‐Ac) was obtained from such a PIB‐OH, and the PIB‐T was subsequently prepared by Michael addition of thymine across the acrylate double bond. MALDI‐ToF MS of the products verified that all polymer chains carried precisely one thymine group. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3501–3506, 2010     

Photoinitiated polymerization of acrylate,methacrylate, and vinyl ether end‐functional polyisobutylene macromonomers

Polyisobutylene‐based UV cured networks potentially useful as sealants were synthesized by photopolymerization of well‐defined polyisobutylene methacrylate (PIB‐MA), acrylate (PIB‐A) and vinyl ether (PIB‐VE) di‐ and trifunctional macromonomers. The kinetics of photocrosslinking were measured using an optical pyrometer apparatus and optimized with respect to different experimental parameters. PIB‐MA/A macromonomers displayed enhanced reactivity in radical photopolymerization in the presence of a bis(acylphosphine) oxide photoinitator. PIB‐VE macromonomers exhibited a high rates of photopolymerization with (4‐n‐octyloxyphenyl)phenyliodonium hexafluroantimonate as the photoinitiator. The rates as well as the ultimate monomer conversions were increased by increasing the irradiation light intensity. The inherent induction period associated with oxygen inhibition in the photopolymerization of PIB‐MA was significantly reduced by optimizing the choice of photoinitiator. A detailed investigation of the concentration of MA/A/VE end groups revealed the presence of a prominent saturation effect in the photopolymerization of PIB‐A, which was absent with PIB‐MA and PIB‐VE. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

One‐pot synthesis of isocyanate and methacrylate multifunctionalized polyisobutylene and polyisobutylene‐based amphiphilic networks

Amphiphilic polymer networks consisting of hydrophilic poly(2‐hydroxyethyl methacrylate) (PHEMA) and hydrophobic polyisobutylene (PIB) chains were synthesized from a cationic copolymer of isobutylene (IB) and 3‐isopropenyl‐α,α‐dimethylbenzyl isocyanate (IDI) prepared at ?50 °C in dichloromethane in conjunction with SnCl₄. The isocyanate groups of this random copolymer, PIB(NCO)_n, were subsequently transformed in situ to methacrylate (MA) groups in the dibutyltin dilaurate‐catalyzed reaction with 2‐hydroxyethyl methacrylate (HEMA) at 30 °C. The resulting PIB(MA)_n with number–average molecular weight 8200 and average functionality F_n ～ 4 per chain was in situ copolymerized radically with HEMA at 70 °C, giving rise to the amphiphilic networks containing 41 and 67 mol % HEMA. PHEMA–PIB network containing 43 mol % HEMA was also prepared by radical copolymerization of PIB(MA)_n precursor with HEMA using sequential synthesis. An amphiphilic nature of the resulting networks was proved by swelling in both water and n‐heptane. PIB(NCO)_n and PIB(MA)_n were characterized by FTIR spectroscopy, SEC and the latter also by ¹H NMR spectroscopy. Solid state ¹³C NMR spectroscopy was used for characterization of the resulting PHEMA–PIB networks. Whereas single glass‐transition temperature, T_g = ?67.4 °C, was observed for the rubbery crosslinked PIB prepared by reaction of PIB(NCO)_n with water, the PHEMA–PIB networks containing 67 and 41 mol % HEMA showed two T_g's: ?70.4 and 102.7 °C, and ?63 and 107.2 °C, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2891–2900, 2006     

Block copolymers derived from polyisobutylene oligomers

The synthesis of polyvalent functionalized polyisobutylene (PIB) oligomers containing multiple polar groups via radical polymerization is described. Polymerizations from PIB macroinitiators via alkylborane intermediates can form block copolymers but the polar block is consistently larger than the PIB block and unless a hydrophobic monomer is used, the products are insoluble in alkanes. Block copolymer products from ATRP macroinitiators are formed with more control over the degree of polymerization of a polar block from a 1000 Da PIB starting material but are still alkane insoluble because the degree of polymerization of the polar block was consistently equal to or greater than the degree of polymerization of the PIB block. RAFT polymerization using 5 mol % of azoisobutyronitrile relative to a PIB macroinitiator however was successful in producing acceptable yields of alkane soluble block copolymers using a 1000 Da PIB starting material and monomers like methyl methacrylacrylate, ethyl methacrylate, N,N‐dimethylacrylamide, and N‐isopropylacrylamide. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1860–1867     

Polyisobutylene‐based polyurethanes. IX. synthesis,characterization, and properties of polyisobutylene‐based poly(urethane‐ureas)

Polyisobutylene (PIB)‐based polyurethanes (PUs) exhibit unparalleled hydrolytic‐oxidative‐biologic stability and are melt processible, however, their mechanical (strength) properties are modest mainly due to insufficient H bonds. We posited and demonstrate that the ultimate properties of PIB‐PUs are enhanced, while their melt processibility is maintained, by the judicious introduction of urea linkages, i.e., strong bifurcated H bonds, in the chain. The incorporation of bifurcated H bonds in PIB‐PUs was achieved by using the conventional butane diol chain extender (CE) in combination with controlled amounts of amino alcohol as co‐chain extender (co‐CE). Polyurethanes containing both urethane and urea linkages are polyurethane‐ureas (PUU). Specifically, PIB‐PUUs prepared with PIB‐diol/MDI together with 80/20 mole % butane diol/amino butanol exhibited ～30 MPa tensile strength, ～550% elongation, ～80 Shore A hardness, and ～137 °C flow temperature. Other amino alcohols, i.e., amino ethanol, ‐propanol, and ‐hexanol, were less effective co‐CEs. ¹H‐NMR and FT‐IR spectroscopies indicate the presence of bifurcated H bonds in PIB‐PUUs prepared with CE/co‐CE combinations. Characterization by differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical thermal analysis, and creep experiments also suggest bifurcated H bonds in PIB‐PUU. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2361–2369     

Molecular motion of ends of isolated poly(isobutylene) chains tethered on the poly(tetrafluoroethylene) surface in vacuo

Poly(isobutylene) (PIB) chains with a radical at the chain end were graft-copolymerized on the poly(tetrafluoroethylene) (PTFE) surface in vacuo at 77 K. The PIB chains tethered on the PTFE surface in vacuo were regarded as isolated chains from neighboring tethered PIB chains. The molecular motion of the ends of the isolated PIB chains was observed by an electron spin resonance (ESR) spectrometer in the temperature range from 3 to 125 K, which was lower than T_g of PIB, 200 K,¹ and two motion modes were found: One is a quantum tunneling of the methyl group located at the chain end at 3 K, and the other is an interconformation transition with freely rotating methyl group at the end at 77 K, where the transition rate was estimated to be 15 MHz at that temperature. The transition rate increased with an increase in temperature. The activation energy of the transition was estimated to be 370 J/mol. The high mobility and low activation energy was attributed to the isolation of PIB chains in vacuo. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2095–2102, 1998     

Synthesis and characterization of carboxylic acid‐terminated polyisobutylenes

tert-Chloride-terminated polyisobutylenes (PIB) (1020 ≤ M_n ≤ 6700 g/mol) were dehydrochlorinated nonregiospecifically using basic alumina, or regiospecifically either via potassium tert-butoxide or in situ quenching of quasiliving PIB. Olefin-terminated PIBs were quantitatively ozonized at −78 °C using hexane/methylene chloride/methanol, 62/31/7 (v/v/v) cosolvents, and an ozone generator, employing pure oxygen as source gas. The primary ozonides were reduced using trimethyl phosphite to yield pure PIB methyl ketone from exo-olefin PIB, and a mixture of PIB methyl ketone and PIB aldehyde from mixed olefin-PIB. PIB methyl ketone was oxidized to carboxylate via the haloform reaction; titration revealed near-quantitative functionalization, but the reaction was slow. Tetrahalomethane oxidation was identified as a preferred alternative method, and was conducted using either CCl₄ as the reaction solvent, THF as the solvent with CCl₄ in reagent amounts, or hexane as the solvent with a phase-transfer catalyst and CCl₄ in reagent amounts. The system using hexane, with tetra-n-butyl ammonium chloride as phase-transfer catalyst, showed complete conversion in ∼ 4 h. PIB carboxylic acid was recovered by acidification and isolation. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3229–3240, 2008     

Low‐cost bifunctional initiators for bidirectional living cationic polymerization of olefins. III. centrally functionalized polyisobutylenes

Allyl‐telechelic polyisobutylene (A‐PIB‐A) produced by the bis‐benzocyclobutane dichloride (bBCB‐diCl) initiator contains the bis‐benzocyclobutane (bBCB) fragment at the center of the macromolecule (A‐PIB‐bBCB‐PIB‐A). Thermolysis of A‐PIB‐bBCB‐PIB‐A quantitatively converts the central bBCB fragment to a substituted conjugated tetraene (A‐PIB‐tetraene‐PIB‐A). The structure of A‐PIB‐tetraene‐PIB‐A was anticipated from small molecule models and identified/quantitated by ¹H NMR spectroscopy. This is the first time a reactive functional group was introduced at the statistical center of a (telechelic) PIB. Subsequently, the A‐PIB‐tetraene‐PIB‐A was peroxidized to an epoxy derivative. Reaction of the A‐PIB‐tetraene‐PIB‐A with HSCH₂CH₂OH produced HOCH₂‐telechelic PIB containing a central  CH₂OH function, and hydrosilation with HSi(Me₂)‐O‐Si(Me₂)H produced SiH‐telechelic PIB with a central  SiH function. Reactions with maleic anhydride, tetracyanoethylene, butyl lithium, and potassium permanganate have also been examined. In sum, A‐PIB‐bBCB‐PIB‐A and A‐PIB‐tetraene‐PIB‐A are useful intermediates for the synthesis of novel PIB‐based materials for various end uses under investigation. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1140–1145     

Polyisobutylene‐based polyurethanes: VII. structure/property investigations for medical applications

The outstanding hydrolytic and oxidative stabilities of polyisobutylene‐based polyurethanes (PIB‐based PUs) were reported earlier. Herein, we summarize recent investigations aimed at further enhancing hydrolytic‐oxidative stabilities (in terms of resistance to aqueous buffer, nitric acid and CoCl₂/H₂O₂) together with excellent mechanical properties. The purity and dryness of ingredients together with precise NCO/OH stoichiometry (～1.05) are essential to obtain PIB‐based PUs with improved properties. Static and dynamic mechanical properties were optimized by analyzing stress–strain traces, thermal (TGA, DSC) responses, self‐organization (XRD) profiles, and rheological (DMA, creep) information. According to microstructure and surface analyses (AFM, contact angle) annealing increases the segregation of individual segments and increases surface hydrophobicity, which in turn enhances the shielding of hydrolytically oxidatively vulnerable carbamate bonds by inert PIB barriers, and thus significantly improves hydrolytic‐oxidative stability. Annealing does not much affect bulk properties, such as static and dynamic mechanical and thermal properties; however, it increases damping over a wide temperature range. Annealed PIB‐based PU containing 72.5% PIB exhibits outstanding hydrolytic‐oxidative stability together with ～26 MPa tensile strength, ～500% elongation, and ～77 Microshore hardness. PIB‐based PUs are significantly more resistant to hydrolytic and oxidative degradation than ElastEon? E2A, a commercially available PDMS‐based PU, widely used for medical applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 532–543     

Calcification resistance of polyisobutylene and polyisobutylene‐based materials

Calcification of implanted biomaterials is highly undesirable and limits clinical applicability. Experiments were carried out to assess the calcification resistance of polyisobutylene (PIB), PIB‐based polyurethane (PIB‐PU), PIB‐PU reinforced with (CH₃)₃N⁺CH₂CH₂CH₂NH₂ I^?‐modified montmorillonite (PIB‐PU/nc), PIB‐based polyurethane urea (PIB‐PUU), PIB‐PU containing S atoms (PIB_S‐PU), PIB_S‐PU reinforced with (CH₃)₃N⁺CH₂CH₂CH₂NH₂ I^?‐modified montmorillonite (PIB_S‐PU/nc), and poly(isobutylene‐b‐styrene‐b‐isobutylene) (SIBS), relative to that of a clinically widely implanted polydimethylsiloxane (PDMS)–based PU, Elast‐Eon (the “control”). Samples were incubated in simulated body fluid for 28 days at 37°C, and the extent of surface calcification was analyzed by scanning electron microscopy (SEM), atomic force microscopy (AFM), energy‐dispersive X‐ray spectroscopy (EDX), X‐ray photoelectron spectroscopy (XPS), and Fourier‐transform‐infrared (FT‐IR) spectroscopy. Whereas the PDMS‐based PU showed extensive calcification, PIB and PIB‐PU containing 72.5% PIB, ie, a polyurethane whose surface is covered with PIB, were free of calcification. PIB_S‐PU and PIB‐PUU, ie, polyurethanes that contain S or urea groups, respectively, were slightly calcified. The amine‐modified montmorillonite‐reinforcing agent reduced the extent of calcification. SIBS was found slightly calcified. Evidently, PIB and materials fully coated with PIB are calcification resistant.     

Synthesis of comb‐like dispersants and a study on the effect of dispersant architecture and carbon black dispersion

Comb dispersants suitable for stabilization of carbonaceous deposits found in automotive lubricating oils were derived from the copolymerization of vinyl‐ether terminated polyisobutylene (VE‐PIB) macromonomers with maleic anhydride (MAH). The rate and degree of copolymerization of VE‐PIB with MAH was greatly influenced by the molecular weight of the VE‐PIB. Longer PIB tails imposed greater hindrance of the chain end resulting in slower propagation and lower degrees of copolymerization for PIB‐alt‐MAH copolymers. Functionalization of PIB‐alt‐MAH with a polyamine proceeded smoothly at elevated temperatures as evidenced by disappearance of anhydride stretches via Fourier transform infrared spectroscopy. Analogous linear and grafted dispersants were prepared to investigate the influence of architecture on the physical properties of the dispersants. Characterization of the intermediates and final dispersants was conducted by nuclear magnetic resonance, gel permeation chromatography, thermogravimetric analysis, and ultraviolet–visible. Using Langmuir adsorption studies and carbon black as a substitute for carbonaceous deposits, it was found that comb and grafted dispersants exhibit greater affinities for adsorption but decreased packing efficiencies in comparison to linear dispersants. Rheological studies investigating viscosity as a function of loading for dispersant/oil mixtures with carbon black present a similar finding. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1682–1696     

Synthesis and characterization of two novel star blocks: tCum[poly(isobutylene‐b‐norbornadiene)]3 and tCum[poly(norbornadiene‐b‐isobutylene)]3

Two structurally closely related three‐arm star blocks were synthesized and characterized: tCum(PIB‐b‐PNBD)₃ and tCum(PNBD‐b‐PIB)₃ [where tCum (tricumyl) stands for the phenyl‐1,3,5‐tris(‐2‐propyl) fragment and PIB and PNBD are polyisobutylene and polynorbornadiene, respectively]. The syntheses were accomplished in two stages: (1) the preparation of the first (or inner) block fitted with appropriate chlorine termini capable of initiating the polymerization of the second (or outer) block with TiCl₄ and (2) the mediation of the polymerization of the second block. Therefore, the synthesis of tCum(PIB‐b‐PNBD)₃ was effected with tCum(PIB‐Cl^t)₃ [where Cl^t is tert‐chlorine and number‐average molecular weight (M_n) = 102,000 g/mol] by the use of TiCl₄ and 30/70 CH₃Cl/CHCl₃ solvent mixtures at ?35 °C. PNBD homopolymer contamination formed by chain transfer was removed by selective precipitation. According to gel permeation chromatography, the M_n's of the star blocks were 107,300–109,200 g/mol. NMR spectroscopy (750 MHz) was used to determine structures and molecular weights. Differential scanning calorimetry (DSC) indicated two glass‐transition temperatures (T_g's), one each for the PIB (?65 °C) and PNBD (232 °C) phases. Thermogravimetric analysis thermograms showed 5% weight losses at 293 °C in air and at 352 °C in N₂. The synthesis of tCum(PNBD‐b‐PIB)₃ was achieved by the initiation of isobutylene polymerization with tCum(PNBD‐Cl^sec)₃ (where Cl^sec is sec‐chlorine and M_n = 2900 g/mol) by the use of TiCl₄ in CH₃Cl at ?60 °C. DSC for this star block (M_n = 14,200 g/mol) also showed two T_g's, that is, at ?67 and 228 °C for the PIB and PNBD segments, respectively. It is of interest that the Cl^sec terminus of PNBD, , readily initiated isobutylene polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 740–751, 2003     

Novel block ionomers. I. Synthesis and characterization of polyisobutylene‐based block anionomers

A series of novel block anionomers consisting of polyisobutylene (PIB) and poly(methacrylic acid) (PMAA) segments were prepared and characterized. The specific targets were various molecular weight diblocks (PIB‐b‐PMAA^?), triblocks (PMAA^?‐b‐PIB‐b‐PMAA^?), and three‐arm star blocks [Φ(PIB‐b‐PMAA^?)₃] consisting of rubbery PIB blocks with a number‐average degree of polymerization of 50–1000 (number‐average molecular weight = 3000–54,000 g/mol) connected to blocks of PMAA^? anions with a number‐average degree of polymerization of 5–20. The overall strategy for the synthesis of these constructs consisted of four steps: (1) synthesis by living cationic polymerization of t‐chloro‐monotelechelic, t‐chloro‐ditelechelic, and t‐chloro‐tritelechelic PIBs; (2) site transformation to obtain PIBs fitted with termini capable of mediating the atom transfer radical polymerization (ATRP) of tert‐butyl methacrylate (tBMA); (3) ATRP of tBMA, and (4) hydrolysis of poly(tert‐butyl methacrylate) to PMAA^?. The architectures created and the synthesis steps employed are summarized. Kinetic and model experiments greatly assisted in the development of convenient synthesis methods. The microarchitectures of the various block anionomers were confirmed by spectroscopy and other techniques. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3662–3678, 2002