Investigating Chain Dynamics in Highly Crosslinked Polymers using Solid‐State 1H NMR Spectroscopy

Solid state ¹H NMR line‐shape analysis and (double quantum) DQ ¹H NMR experiments have been used to investigate the segmental and polymer chain dynamics as a function of temperature for a series of thermosetting epoxy resins produced using different diamine curing agents. In these thermosets, chemical crosslinks introduce topological constraints leading to residual stresses during curing. Materials containing a unique ferrocene‐based diamine (FcDA) curing agent were evaluated to address the role of the ferrocene fluxional process on the atomic‐level polymer dynamics. At temperatures above the glass transition temperature (T_g), the DQ ¹H NMR experiments provided a measure of the relative effective crosslink and entanglement densities for these materials and revealed significant polymer chain dynamic heterogeneity in the FcDA‐cured thermosets. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1143–1156     

Simultaneous measurements of T1 and T2 during fast polymerization reaction using continuous wave‐free precession NMR method

Continuous wave‐free precession (CWFP) pulse sequence employing time domain nuclear magnetic resonance spectroscopy (TD‐NMR) was used to measure longitudinal (T₁) and transverse relaxation times (T₂), during the cure of a commercial epoxy resin (Araldite^TM) with a 10‐min solidification time. The intensity of the NMR signal after the first pulse and in the CWFP regime were used to monitor the concentration of the monomers, and the relaxation times were used to monitor the chain mobility. The main advantage of CWFP over the standard methods to measure relaxation times, inversion recovery (inv‐rec) for T₁ and Carr‐Purcell‐Meiboom‐Gill (CPMG) for T₂, is that the measurement of both relaxation times can be performed in a fast and single NMR experiment and, therefore, using a single reaction batch. CWFP is also as fast as the CPMG measurement but at least fivefold faster than the method to obtain T₁ using null point approximation in the inv‐rec method. Therefore, the CWFP sequence can be used as a fast and general method to measure relaxation times in polymerization reactions, even with fast solidification time. As a TD‐NMR technique, CWFP can be employed in any low‐cost bench top TD‐NMR equipment commonly used in an academic or industrial laboratory. Copyright © 2012 John Wiley & Sons, Ltd.     

Identification of complex structures of paintings on canvas by NMR: Correlation between NMR profile and stratigraphy

Paintings on canvas are complex structures created by superimposing layers of different composition. Investigations on the structure of these artworks can provide essential information on their state of conservation, pictorial technique, possible overpaintings, and in planning a proper conservation plan. Standard methods of investigation consist in sampling a limited number of fragments for stratigraphic analyses. Despite the recognized validity of these methods, they are affected by evident limitations. Nuclear magnetic resonance (NMR) profiling, often named NMR stratigraphy, is an NMR relaxometry technique applied by single-sided portable devices developed to overcome the disadvantages of microinvasive stratigraphic analyses. The potential of this approach on artworks, including wall paintings and a few examples of painted canvas, is described in the literature. In this study, NMR profiles of painting on canvas were examined by analyzing transverse relaxation time data by T₂ quasi-continuous distributions and the results compared with standard stratigraphic cross-sections analysis. Combining signal intensity and T₂ quasi-continuous distributions, the identification of textile, preparatory, and paint layers was enhanced. The diction “NMR stratigraphy” for these inhomogeneous layered artworks is also discussed. Indeed, unlike the stratigraphic cross-sections, NMR profiles provide information on a volume (flat slice), rather than on a surface, and the collected signal can derive from nonuniform and partially overlapping layers. This study paves the way for extensive investigations on relaxation time quasi-continuous distributions in various binder/pigment mixtures in order to improve the reliability of NMR profile as an innovative, non–invasive, and nondestructive method for analyzing paintings on canvas.     

Facile preparation of novel epoxy curing agents and their high‐performance thermosets

Two flame‐retardant epoxy curing agents, 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐yl‐tris(4‐hydroxyphenyl)methane (1) and 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐yl‐ (4‐aminophenyl)‐bis(4‐hydroxyphenyl)methane (2), were prepared by a facile, economic, one‐pot procedure. The structures of the curing agents were confirmed by IR, high‐resolution mass, 1‐D, and 2‐D NMR spectra. A reaction mechanism was proposed for the preparation, and the effect of electron withdrawing/donating effects on the stabilization of the carbocation was discussed. (1‐2) served as curing agents for diglycidyl ether of bisphenol A (DGEBA), dicyclopentadiene epoxy (HP‐7200), and cresol novolac epoxy (CNE). Properties such as glass transition temperature, coefficient of thermal expansion, thermal decomposition temperature, and flame retardancy of the resulting epoxy thermosets were evaluated. The resulting epoxy thermosets show high T_g, low thermal expansion, moderate thermostability, and excellent flame retardancy. The bulky biphenylene phosphinate pendant makes polymer chains difficult to rotate, explaining the high T_g and low thermal expansion characteristic. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7898–7912, 2008     

Thermal cured epoxy resins using certain calixarenes and their esterified derivatives as curing agents

The acetyl esterified calixarene (CA) derivatives were prepared from calix[4]resorcinarene (CRA), and p‐tert‐butylcalixarene (BCA[n], n = 4, 6, 8), respectively. Using these CA derivatives as curing agents, the thermal curing reactions of two multifunctional epoxy resins (jER 828, 186 g/equiv., and ESCN, 193.7 g/equiv.) were investigated. The temperatures of glass transition (T_g) and decomposition (T) were measured by DSC and TGA, respectively. Based on the yields, T_gs, and T_ds of the thermal cured jER 828 epoxy resin with CRA‐E100, the curing conditions were optimized to be tetrabutylphosphonium bromide (TBPB) as catalyst in NMP at 160 °C for 15 h. Under this curing condition, the cured materials of jER 828 or ESCN using various CA derivatives as curing agents were prepared. Except for BCA4 derivatives, the yields of thermal curing reaction were higher than 90%. T_gs and Ts of the resultant cured materials were in the range of 113–248 °C and 363–404 °C, respectively. These results mean that the cured epoxy resins with excellent T_gs were successfully formed by using CA derivatives as curing agents. It was also found that the T_gs of cured epoxy resins were strongly affected by the degree of esterification of CA derivatives. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1931–1942, 2010     

Quantitative nuclear magnetic resonance imaging of liquids in swelling polymers

The variation of nuclear magnetic resonance (NMR) relaxation parameters (T₁, T₂) within a polymer during swelling, limits the absolute accuracy with which liquid concentration profiles can be obtained using NMR imaging. In this article a study of the diffusion of decalin into ultra-high molecular weight polyethylene (UHMWPE) is reported. The study illustrates the use of a method of analysis whereby quantitative solvent profiles can be obtained from data influenced by both T₁ and T₂ contrast effects. A T₁ and T₂ map are obtained at a point in the uptake of liquid where the greatest range in liquid concentration is obtained at a point in the uptake of liquid where the greatest range in liquid concentration is observed. The intensity of signal corresponding to liquid in the polymer is compared to that of pure liquid in a reference sample, and correlations for T₁ and T₂ values versus signal intensity are used to deconvolve relaxation contrast, to yield the true liquid concentration. The technique was used to study the effect of degree of crosslinking of UHMWPE on the swelling kinetics and decalin transport within the polymer. A spin-echo imaging technique was used with a recycle delay approximately equal to the average spin-lattice relaxation time of the liquid, and an echo time approximately half the average spin-spin relaxation time. Under these conditions the relaxation contrast was significant, yet the mass uptake data derived from the concentration profiles obtained, using the method of analysis described, agreed well with gravimetric data. © 1995 John Wiley & Sons, Inc.     

The physical properties of bisphenol-a-based epoxy resins during and after curing. II. Creep behavior above and below the glass transition temperature

The creep behavior of a series of fully cured epoxy resins with different crosslink densities was determined from the glassy compliance level to the equilibrium compliance J_e at temperatures above T_g and at the glassy level below T_g during spontaneous densification at four aging temperatures, 4,4-diamino diphenyl sulfone DDS was used to crosslink the epoxy resins. The shear creep compliance curves J(t) obtained with materials at equilibrium densities near and above T_g were compared at their respective T_gs. T_gs from 101 to 205°C were observed for the epoxies which were based on the diglycidyl ether of bisphenol A. Creep rates were found to be the same at short times, and equilibrium compliances J_e were close to the predictions of the kinetic theory of rubberlike elasticity. Time scale shift factors determined during physical aging were reduced to T_g. At compliances below 2 × 10^?10 cm²/dyn, Andrade creep, where J(t) is a linear function of the cube root of creep time, was observed. The time to reach an equilibrium volume at T_g was found to be longer for the epoxy resin with lower crosslink densities. The increase of density during curing is illustrated for the epoxy resin with the highest crosslink density.     

Real-Time NMR. How Fast Can We Do It?

Network structure development during cross-linking photopolymerization of polyethylene glycol di-acrylate and its mixture with a mono-functional 2-ethylhexyl acrylate was studied using real-time proton NMR T₂ relaxation analysis. The time resolution of the method is typically in the order of seconds. The results reveal largely heterogeneous origin of network build up at the intermediate stages of photocuring. Domains of nano-gel are already formed on initial stages of UV-curing where hardly any change in viscosity is observed. Upon increasing curing time the fraction of gel increases at the expence of sol, the molar mass of network chains decreases and the molar mass of sol increases. The presence of mono-acrylate slows down the curing rate. The curing continues after UV-illumination causing a significant increase in the amount of gel and cross-link density in the gel. Thus, the NMR method is a valuable tool for characterization of the kinetics of photopolymerization, the development of molecular structure and the resultant molecular scale heterogeneity during photocuring.     

Glass transition temperature for epoxy-diamine networks

The glass transition temperature of systems based on epoxy resin and a number of diamines has been determined by using a torsion pendulum. An equation relating composition and crosslink density with the glass transition temperature has been established which gives reasonable predictions of the glass transition temperatures for systems based on aliphatic or aromatic amines and methylated amines and for systems containing a monofunctional epoxy diluent. The equation may be used to predict T_g for systems with non-stoichiometric quantities of curing agent and blends of amines. Deviation of the predicted and observed values for T_g is interpreted in terms of differences between definitions of T_g used by other workers and, also the occurrence of competing side reactions during polymerization which lead to additional crosslinks.     

NMR Microscopy—Fundamentals,Limits and Possible Applications

Alongside the numerous applications of NMR spectroscopy to structural elucidation in analytical chemistry, and to biochemical and morphological studies by NMR tomography, NMR microscopy makes possible a whole new range of applications. These include imaging, the investigation of biological objects such as plants and small animals, and also the observation of microscopic structures and structural changes in polymers and ceramics. NMR spectroscopy can also be conducted combinationally as volume-selective spectroscopy, whereby it is possible to spatially resolve the NMR-specific parameters: spin density ?, chemical shifts δ, and the relaxation times T₁ and T₂. The numerous well developed methods available make it possible to study dynamic processes by fast imaging with a temporal resolution in milliseconds. This not only allows the imaging of moving objects without incurring movement artefacts but also the measurement of diffusion constants in isotropic and anisotropic diffusion—in the latter case allowing, in principle, the determination of the complete diffusion tensor. The spatially resolved measurement of the relaxation times yields information on molecular mobility and bonding, e. g. the bonding of water, or other solvents, to polymers, the mobility of fluids in polymers or ceramics, or the three-dimensional evaluation of pore size in porous materials. In biomedicine, NMR microscopy allows the observation of growth on the cellular level, the study of embryos, and the development of therapeutic methods in animal experiments. It can lead to a drastic reduction in the number of animal experiments, and in combination with volume-selective spectroscopy gives valuable information on in-vivo metabolism.     

The physical properties of bisphenol-A-based epoxy resins during and after curing

A series of epoxy resins derived from diglycidyl ethers of bisphenol A with differing initial linear molecular chain lengths have been studied during and after curing with the diamines MDA (4,4′-methylene dianiline) and DDS (4,4′-diamino diphenyl sulfone). The properties that were measured during curing were the volume, the fictive temperature T_f, the gel fraction, the viscosity, and the equilibrium compliance. Graphs of T_f as a function the time of curing t_c obtained at four curing temperatures between 40 and 100°C have been reduced to a common curve. After curing, creep compliance curves J(t) were determined which characterize the viscoelastic response from the glassy compliance level to a rubbery equilibrium compliance level. The change in properties that occurs during the time-dependent spontaneous densification below the glass temperature T_g was monitored with repeated measurements of J(t). Time-scale shift factors as a function of volume contraction obtained during this physical aging below T_g were reduced to a common curve.     

Curing behavior of epoxy resins with a series of novel curing agents containing 4,4′-biphenyl and varying methylene units

A new homologous series of curing agents (LCECAn) containing 4,4′-biphenyl and n-methylene units (n = 2, 4, 6) were successfully synthesized. The curing behaviors of a commercial diglycidyl ether of bisphenol-A epoxy (E-51) and 4,4′-bis(2,3-epoxypropoxy)biphenyl (LCE) by using LCECAn as the curing agent have been investigated by differential scanning calorimetry (DSC), respectively. The Ozawa equation was applied to the curing kinetics based upon the dynamic DSC data, and the isothermal DSC data were fitted using an autocatalytic curing model. The glass transition temperatures (T _g) of the cured epoxy systems were determined by DSC upon the second heating, and the thermal decomposition temperatures (T _d) were obtained by thermogravimetric (TG) analyses. The results show that the number of methylene units in LCECAn has little influence on the curing temperatures of E-51/LCECAn and LCE/LCECAn systems. In addition, the activation energies obtained by the dynamic method proved to be larger than those by the isothermal method. Furthermore, both the T _g and T _d of the cured E-51/LCECAn systems and LCE/LCECAn systems decreased with the increase in the number of methylene units in LCECAn.     

Mechanical and Thermal Properties and Morphology of Epoxy Resins Modified by a Silicon Compound

A silicon compound (GAPSO) was synthesized to modify the diglycidyl ether of bisphenol-A (DGEBA). The chemical structure of GAPSO was confirmed using FT-IR, ²⁹Si NMR and GPC. The mechanical and thermal properties and morphologies of the cured epoxy resins were investigated by impact testing, tensile testing, differential scanning calorimetry and environmental scanning electron microscopy. The impact strength and tensile strength were both increased by introducing GAPSO, meanwhile the glass transition temperature (T_g ) was not decreased and the morphologies of the fracture surfaces show that the compatibility of GAPSO with epoxy resin was very good and the toughening follows the pinning and crack tip bifurcation mechanism. The high functional groups in GAPSO can react during the curing process, and chemically participate in the crosslinking network. GAPSO is thus expected to improve the toughness of epoxy resin, meanwhile maintain the glass transition temperature.     

Toughening of a trifunctional epoxy system: IV. Dynamic mechanical relaxational study of the thermoplastic-modified cure process

Dynamic mechanical spectroscopy has been used to investigate the cure of a thermoplastically modified trifunctional epoxy resin. The complex dissolution, curing behavior, and variations in the glass transition of the thermoplastic (PSF) phase were described, as was the T_g behavior of the epoxy phase. Prereaction of the PSF material with the epoxy resin was found to greatly increase the solubility of the PSF in the epoxy phase with little effect on the concentration of the epoxy monomer dissolving in the PSF phase. The curing behavior of the epoxy component in the thermoplastic phase was also investigated, in addition to changes in the mobility of the network at both gelation and vitrification. © 1997 John Wiley & Sons, Inc.     

SYNTHESIS AND NMR CHARACTERIZATION OF PRECURSORS OF EPOXY NETWORK AS POLYMER HOST FOR SOLID ELECTROLYTE

To raise the room temperature ionic conductivity and improve the mechanical strength of a PEO-based polymer electrolyte, a noncrystalline two-component epoxy electrolyte system has been prepared. The diglycidyl ether of polyethylene glycols as precursors of the system were synthesized by a two-step process. The presumed structure of the product was characterized, by ~(13)C, ~1H NMR and IR spectroscopy. It was found that a side-reaction occurred between the secondary hydroxyl group of PEG-chlorohydrin and epichlorohydrin in some degree, resulting in a by- product containing—CH_2Cl side group. By selecting a characteristic signal, which is undistorted by the increase in the length of CH_2 CH_2—O segment, a ~1H NMR approach of determining the equivalent epoxy weight (EEW) was proposed. The method is valid to specimens even though the EEW is as high as 2,000. The examination of the specimens by DSC showed that epoxidation greatly depressed the crystallinity of the PEG's, whereas the T_g was raised.     

Epoxy resins (DGEBA): The curing and physical aging process

Differential scanning calorimetry (DSC) and infrared spectroscopy (IR) were used to monitor the degree of cure of partially cured epoxy resin (Epon 828/MDA) samples. The extent of cure, as determined by residual heat of reaction, concurred with that determined by monitoring the infrared radiation absorbance of the epoxide group near 916 cm^?l. The fictive temperature T_{f, g} was found to increase with the degree of cure, increasing rapidly during cure until reaching a value near the cure temperature T_c of 130°C (approximately 80% cure) where the material vitrified. The greatly reduced reaction rate during the final 20% of cure was not only a consequence of vitrification but, as revealed by infrared spectroscopy, the result of the depletion in the number of reactive epoxide groups. The endothermic peak areas and peak temperatures evident during the DSC scans were used as a measure of the extent of “physical aging” which took place during the cure of this resin, and after, fully cured samples were aged 37°C below their ultimate glass temperature for various periods of time. The rate of physical aging slowed as the temperature increment (T_t,g ? T_c) increased. Although an endothermic peak was evident after only 1 h of cure (T_{f, g} = 138.3°C), such a peak did not appear until fully cured samples were aged for 16 h or more. Enthalpy data revealed that for partially cured material, the fictive temperature T_{f, a}, reflecting physical aging, increased with curing time. In contrast, the T_{f, a}, for fully cured samples decreased with sub-T_g aging time. The characteristic jump in the heat capacity ΔC_p which occurred at the T_{f, g} decreased as curing progressed. This decrease appears to be dependent upon the rotational and vibrational degrees of freedom of the glass. Finally, a graphical method of determining the fictive temperature T_{f, a}, of partially and fully cured epoxy material from measured endothermic peak areas was developed.     

Synthesis and properties of two novel silicon‐containing cycloaliphatic epoxy resins for electronic packaging application

In this paper, two silicon‐containing cycloaliphatic olefins were synthesized through the nucleophilic substitution reactions of cyclohex‐3‐enyl‐1‐methanol with di‐ or tri‐chlorosilane compounds. Then, after epoxidation, two new cycloaliphatic epoxy resins with different epoxy groups were successfully prepared. Their chemical structures were confirmed by ²⁹Si NMR, ¹H NMR, and Fourier‐transform infrared spectra (FTIR). The properties of cured products, including viscoelasticity, glass transition temperature (T_g), coefficient of thermal expansion, thermal stability and water absorption, were investigated. Compared to the difunctional epoxy resin, the trifunctional one exhibited a remarkably increased cross‐linking density from 0.82 to 4.08 × 10^?3 mol/cm³ and T_g from 157 to 228°C. More importantly, prior to curing, they had viscosities of only 240–290 mPa sec at 25°C, which were much lower than that of ERL‐4221 (409 mPa sec), providing the possibility of easy processing. The high glass transition temperatures, good thermal stabilities, and mechanical properties as well as excellent flowability endow the silicon‐containing epoxy resins with promising potential in microelectronic packaging application. Copyright © 2011 John Wiley & Sons, Ltd.     

Preparation, characterization and curing properties of epoxy-terminated poly(alkyl-phenylene oxide)s

A series of dihydroxyl telechelic poly(alkyl-phenylene oxide)s (1) have been synthesized by oxidative polymerization of alkylphenols with various aromatic diols using manganese or copper amine catalysts. The novel telechelic derivatives (1) were epoxidized with epichlorohydrin yielding a series of new epoxidized poly(alkyl-phenylene oxide)s (EPPO, 2) and the structures, properties were studied by nuclear magnetic resonance spectroscopy (NMR), differential scanning calorimetry (DSC), thermo gravimetric analysis (TGA) and gel permeation chromatography (GPC). The 1:1 blends of diglycidyl ether of bisphenol-A (DGEBA) with EPPO resins were cured with three curing agents and the effects of chemical structure change on thermal property of the curing matrixes were discussed. Incorporation of EPPOs to DGEBA epoxy system resulted in a significant increase in its glass transition temperature (T_g), thermal stability and flame resistance. The T_g values and char yields arising from a DDM-cured epoxy resin are usually higher than those of dicyandiamide (DICY) or 2-methylimidazole (2-MI) analogues and the reactivity of epoxy blends with three curing agents presents an increase in the order of 2-MI, DDM and DICY. In general, the tetramethylbisphenol-A (TMBPA)-derived polymer exhibits the lowest T_g, char yield and dielectric constant among PPO derivatives whereas the biphenol polymers usually results in higher T_g and char yield due to its rigid rod structure.     

Phase Behavior in Blends of Ethylene Oxide–Propylene Oxide Copolymer and Poly(ether sulfone) Studied by Modulated-Temperature DSC and NMR Relaxometry

The state diagram of a blend consisting of a copolymer containing ethylene oxide and propylene oxide, P(EO-ran-PO), and poly(ether sulfone), PES, is constructed by using modulated-temperature differential scanning calorimetry (MTDSC), T₂ NMR relaxometry, and light scattering. The apparent heat capacity signal in MTDSC is used for the characterization of polymer miscibility and morphology development. T₂ NMR relaxometry is used to detect the onset of phase separation, which is in good agreement with the onset of phase separation in the apparent heat capacity from MTDSC and the cloud-point temperature as determined from light scattering. The coexistence curve can be constructed from T₂ values at various temperatures by using a few blends with well-chosen compositions. These T₂ values also allow the detection of the boundary between the demixing zones with and without interference of partial vitrification and are in good agreement with stepwise quasi-isothermal MTDSC heat capacity measurements. Important interphases are detected in the heterogeneous P(EO-ran-PO)/PES blends.     

Dual nuclear magnetic resonance for probing intrinsic bone structure and a potential gut–bone axis in ovariectomized rats

Currently, the existence of a gut–bone axis receives massive attention, and while sound premises and indirect proofs exist for the gut–bone axis concept, few studies have provided actual data linking the gut and bone physically. This study aimed to exploit the versatile nature of nuclear magnetic resonance (NMR) to link NMR relaxometry data on bone mineralization with NMR spectroscopic profiling of gut metabolites. For this purpose, sample material was obtained from a 6-week intervention study with ovariectomized (OVX) rats (n = 49) fed with seven different diets varying in calcium content (0.2–6.0 mg/kg) and prebiotic fiber content (0–5.0% w/w). This design ensured a span in (i) calcium available for bone mineralization and (ii) metabolic activity in the gut. After termination of the intervention, longitudinal (T₁), transverse (T₂) relaxation, and mechanical bone strength were measured on the excised femur bones. A PLS model with high predictability (Q² = 0.86, R² = 0.997) was demonstrated between T₂ decay curves and femur mechanical strength. Correlations were established between bone T₂ populations and gut short-chain fatty acids. In conclusion, the present dual NMR approach showed strong correlation between T₂ relaxation and mechanical strength of the bone, and when metabolic activity in the gut was modulated by inulin, the potential existence of a gut–bone axis was demonstrated.